@@ -350,10 +350,10 @@ static void aspeed_smc_send_cmd_addr(struct spi_nor *nor, u8 cmd, u32 addr)
__be32 temp;
u32 cmdaddr;
- switch (nor->addr_width) {
+ switch (nor->addr_nbytes) {
default:
WARN_ONCE(1, "Unexpected address width %u, defaulting to 3\n",
- nor->addr_width);
+ nor->addr_nbytes);
fallthrough;
case 3:
cmdaddr = addr & 0xFFFFFF;
@@ -709,7 +709,7 @@ static int aspeed_smc_chip_setup_finish(struct aspeed_smc_chip *chip)
const struct aspeed_smc_info *info = controller->info;
u32 cmd;
- if (chip->nor.addr_width == 4 && info->set_4b)
+ if (chip->nor.addr_nbytes == 4 && info->set_4b)
info->set_4b(chip);
/* This is for direct AHB access when using Command Mode. */
@@ -237,7 +237,7 @@ static int hisi_spi_nor_dma_transfer(struct spi_nor *nor, loff_t start_off,
reg = readl(host->regbase + FMC_CFG);
reg &= ~(FMC_CFG_OP_MODE_MASK | SPI_NOR_ADDR_MODE_MASK);
reg |= FMC_CFG_OP_MODE_NORMAL;
- reg |= (nor->addr_width == 4) ? SPI_NOR_ADDR_MODE_4BYTES
+ reg |= (nor->addr_nbytes == 4) ? SPI_NOR_ADDR_MODE_4BYTES
: SPI_NOR_ADDR_MODE_3BYTES;
writel(reg, host->regbase + FMC_CFG);
@@ -203,7 +203,7 @@ static ssize_t nxp_spifi_write(struct spi_nor *nor, loff_t to, size_t len,
SPIFI_CMD_DATALEN(len) |
SPIFI_CMD_FIELDFORM_ALL_SERIAL |
SPIFI_CMD_OPCODE(nor->program_opcode) |
- SPIFI_CMD_FRAMEFORM(spifi->nor.addr_width + 1);
+ SPIFI_CMD_FRAMEFORM(spifi->nor.addr_nbytes + 1);
writel(cmd, spifi->io_base + SPIFI_CMD);
for (i = 0; i < len; i++)
@@ -230,7 +230,7 @@ static int nxp_spifi_erase(struct spi_nor *nor, loff_t offs)
cmd = SPIFI_CMD_FIELDFORM_ALL_SERIAL |
SPIFI_CMD_OPCODE(nor->erase_opcode) |
- SPIFI_CMD_FRAMEFORM(spifi->nor.addr_width + 1);
+ SPIFI_CMD_FRAMEFORM(spifi->nor.addr_nbytes + 1);
writel(cmd, spifi->io_base + SPIFI_CMD);
return nxp_spifi_wait_for_cmd(spifi);
@@ -252,12 +252,12 @@ static int nxp_spifi_setup_memory_cmd(struct nxp_spifi *spifi)
}
/* Memory mode supports address length between 1 and 4 */
- if (spifi->nor.addr_width < 1 || spifi->nor.addr_width > 4)
+ if (spifi->nor.addr_nbytes < 1 || spifi->nor.addr_nbytes > 4)
return -EINVAL;
spifi->mcmd |= SPIFI_CMD_OPCODE(spifi->nor.read_opcode) |
SPIFI_CMD_INTLEN(spifi->nor.read_dummy / 8) |
- SPIFI_CMD_FRAMEFORM(spifi->nor.addr_width + 1);
+ SPIFI_CMD_FRAMEFORM(spifi->nor.addr_nbytes + 1);
return 0;
}
@@ -38,7 +38,7 @@
*/
#define CHIP_ERASE_2MB_READY_WAIT_JIFFIES (40UL * HZ)
-#define SPI_NOR_MAX_ADDR_WIDTH 4
+#define SPI_NOR_MAX_ADDR_NBYTES 4
#define SPI_NOR_SRST_SLEEP_MIN 200
#define SPI_NOR_SRST_SLEEP_MAX 400
@@ -198,7 +198,7 @@ static ssize_t spi_nor_spimem_read_data(struct spi_nor *nor, loff_t from,
{
struct spi_mem_op op =
SPI_MEM_OP(SPI_MEM_OP_CMD(nor->read_opcode, 0),
- SPI_MEM_OP_ADDR(nor->addr_width, from, 0),
+ SPI_MEM_OP_ADDR(nor->addr_nbytes, from, 0),
SPI_MEM_OP_DUMMY(nor->read_dummy, 0),
SPI_MEM_OP_DATA_IN(len, buf, 0));
bool usebouncebuf;
@@ -262,7 +262,7 @@ static ssize_t spi_nor_spimem_write_data(struct spi_nor *nor, loff_t to,
{
struct spi_mem_op op =
SPI_MEM_OP(SPI_MEM_OP_CMD(nor->program_opcode, 0),
- SPI_MEM_OP_ADDR(nor->addr_width, to, 0),
+ SPI_MEM_OP_ADDR(nor->addr_nbytes, to, 0),
SPI_MEM_OP_NO_DUMMY,
SPI_MEM_OP_DATA_OUT(len, buf, 0));
ssize_t nbytes;
@@ -1143,7 +1143,7 @@ int spi_nor_erase_sector(struct spi_nor *nor, u32 addr)
if (nor->spimem) {
struct spi_mem_op op =
SPI_NOR_SECTOR_ERASE_OP(nor->erase_opcode,
- nor->addr_width, addr);
+ nor->addr_nbytes, addr);
spi_nor_spimem_setup_op(nor, &op, nor->write_proto);
@@ -1156,13 +1156,13 @@ int spi_nor_erase_sector(struct spi_nor *nor, u32 addr)
* Default implementation, if driver doesn't have a specialized HW
* control
*/
- for (i = nor->addr_width - 1; i >= 0; i--) {
+ for (i = nor->addr_nbytes - 1; i >= 0; i--) {
nor->bouncebuf[i] = addr & 0xff;
addr >>= 8;
}
return spi_nor_controller_ops_write_reg(nor, nor->erase_opcode,
- nor->bouncebuf, nor->addr_width);
+ nor->bouncebuf, nor->addr_nbytes);
}
/**
@@ -2279,9 +2279,9 @@ static int spi_nor_default_setup(struct spi_nor *nor,
return 0;
}
-static int spi_nor_set_addr_width(struct spi_nor *nor)
+static int spi_nor_set_addr_nbytes(struct spi_nor *nor)
{
- if (nor->addr_width) {
+ if (nor->addr_nbytes) {
/* already configured from SFDP */
} else if (nor->read_proto == SNOR_PROTO_8_8_8_DTR) {
/*
@@ -2296,26 +2296,26 @@ static int spi_nor_set_addr_width(struct spi_nor *nor)
* Force all 8D-8D-8D flashes to use an address width of 4 to
* avoid this situation.
*/
- nor->addr_width = 4;
- } else if (nor->info->addr_width) {
- nor->addr_width = nor->info->addr_width;
+ nor->addr_nbytes = 4;
+ } else if (nor->info->addr_nbytes) {
+ nor->addr_nbytes = nor->info->addr_nbytes;
} else {
- nor->addr_width = 3;
+ nor->addr_nbytes = 3;
}
- if (nor->addr_width == 3 && nor->params->size > 0x1000000) {
+ if (nor->addr_nbytes == 3 && nor->params->size > 0x1000000) {
/* enable 4-byte addressing if the device exceeds 16MiB */
- nor->addr_width = 4;
+ nor->addr_nbytes = 4;
}
- if (nor->addr_width > SPI_NOR_MAX_ADDR_WIDTH) {
+ if (nor->addr_nbytes > SPI_NOR_MAX_ADDR_NBYTES) {
dev_dbg(nor->dev, "address width is too large: %u\n",
- nor->addr_width);
+ nor->addr_nbytes);
return -EINVAL;
}
/* Set 4byte opcodes when possible. */
- if (nor->addr_width == 4 && nor->flags & SNOR_F_4B_OPCODES &&
+ if (nor->addr_nbytes == 4 && nor->flags & SNOR_F_4B_OPCODES &&
!(nor->flags & SNOR_F_HAS_4BAIT))
spi_nor_set_4byte_opcodes(nor);
@@ -2334,7 +2334,7 @@ static int spi_nor_setup(struct spi_nor *nor,
if (ret)
return ret;
- return spi_nor_set_addr_width(nor);
+ return spi_nor_set_addr_nbytes(nor);
}
/**
@@ -2527,7 +2527,7 @@ static void spi_nor_sfdp_init_params_deprecated(struct spi_nor *nor)
if (spi_nor_parse_sfdp(nor)) {
memcpy(nor->params, &sfdp_params, sizeof(*nor->params));
- nor->addr_width = 0;
+ nor->addr_nbytes = 0;
nor->flags &= ~SNOR_F_4B_OPCODES;
}
}
@@ -2748,7 +2748,7 @@ static int spi_nor_init(struct spi_nor *nor)
nor->flags & SNOR_F_SWP_IS_VOLATILE))
spi_nor_try_unlock_all(nor);
- if (nor->addr_width == 4 &&
+ if (nor->addr_nbytes == 4 &&
nor->read_proto != SNOR_PROTO_8_8_8_DTR &&
!(nor->flags & SNOR_F_4B_OPCODES)) {
/*
@@ -2875,7 +2875,7 @@ static void spi_nor_put_device(struct mtd_info *mtd)
void spi_nor_restore(struct spi_nor *nor)
{
/* restore the addressing mode */
- if (nor->addr_width == 4 && !(nor->flags & SNOR_F_4B_OPCODES) &&
+ if (nor->addr_nbytes == 4 && !(nor->flags & SNOR_F_4B_OPCODES) &&
nor->flags & SNOR_F_BROKEN_RESET)
nor->params->set_4byte_addr_mode(nor, false);
@@ -3060,7 +3060,7 @@ static int spi_nor_create_read_dirmap(struct spi_nor *nor)
{
struct spi_mem_dirmap_info info = {
.op_tmpl = SPI_MEM_OP(SPI_MEM_OP_CMD(nor->read_opcode, 0),
- SPI_MEM_OP_ADDR(nor->addr_width, 0, 0),
+ SPI_MEM_OP_ADDR(nor->addr_nbytes, 0, 0),
SPI_MEM_OP_DUMMY(nor->read_dummy, 0),
SPI_MEM_OP_DATA_IN(0, NULL, 0)),
.offset = 0,
@@ -3091,7 +3091,7 @@ static int spi_nor_create_write_dirmap(struct spi_nor *nor)
{
struct spi_mem_dirmap_info info = {
.op_tmpl = SPI_MEM_OP(SPI_MEM_OP_CMD(nor->program_opcode, 0),
- SPI_MEM_OP_ADDR(nor->addr_width, 0, 0),
+ SPI_MEM_OP_ADDR(nor->addr_nbytes, 0, 0),
SPI_MEM_OP_NO_DUMMY,
SPI_MEM_OP_DATA_OUT(0, NULL, 0)),
.offset = 0,
@@ -90,9 +90,9 @@
SPI_MEM_OP_NO_DUMMY, \
SPI_MEM_OP_NO_DATA)
-#define SPI_NOR_SECTOR_ERASE_OP(opcode, addr_width, addr) \
+#define SPI_NOR_SECTOR_ERASE_OP(opcode, addr_nbytes, addr) \
SPI_MEM_OP(SPI_MEM_OP_CMD(opcode, 0), \
- SPI_MEM_OP_ADDR(addr_width, addr, 0), \
+ SPI_MEM_OP_ADDR(addr_nbytes, addr, 0), \
SPI_MEM_OP_NO_DUMMY, \
SPI_MEM_OP_NO_DATA)
@@ -434,7 +434,7 @@ struct spi_nor_fixups {
* isn't necessarily called a "sector" by the vendor.
* @n_sectors: the number of sectors.
* @page_size: the flash's page size.
- * @addr_width: the flash's address width.
+ * @addr_nbytes: number of address bytes to send.
*
* @parse_sfdp: true when flash supports SFDP tables. The false value has no
* meaning. If one wants to skip the SFDP tables, one should
@@ -493,7 +493,7 @@ struct flash_info {
unsigned sector_size;
u16 n_sectors;
u16 page_size;
- u16 addr_width;
+ u16 addr_nbytes;
bool parse_sfdp;
u16 flags;
@@ -555,11 +555,11 @@ struct flash_info {
.n_sectors = (_n_sectors), \
.page_size = 256, \
-#define CAT25_INFO(_sector_size, _n_sectors, _page_size, _addr_width) \
+#define CAT25_INFO(_sector_size, _n_sectors, _page_size, _addr_nbytes) \
.sector_size = (_sector_size), \
.n_sectors = (_n_sectors), \
.page_size = (_page_size), \
- .addr_width = (_addr_width), \
+ .addr_nbytes = (_addr_nbytes), \
.flags = SPI_NOR_NO_ERASE | SPI_NOR_NO_FR, \
#define OTP_INFO(_len, _n_regions, _base, _offset) \
@@ -20,7 +20,7 @@ is25lp256_post_bfpt_fixups(struct spi_nor *nor,
*/
if ((bfpt->dwords[BFPT_DWORD(1)] & BFPT_DWORD1_ADDRESS_BYTES_MASK) ==
BFPT_DWORD1_ADDRESS_BYTES_3_ONLY)
- nor->addr_width = 4;
+ nor->addr_nbytes = 4;
return 0;
}
@@ -35,13 +35,13 @@
*/
int spi_nor_otp_read_secr(struct spi_nor *nor, loff_t addr, size_t len, u8 *buf)
{
- u8 addr_width, read_opcode, read_dummy;
+ u8 addr_nbytes, read_opcode, read_dummy;
struct spi_mem_dirmap_desc *rdesc;
enum spi_nor_protocol read_proto;
int ret;
read_opcode = nor->read_opcode;
- addr_width = nor->addr_width;
+ addr_nbytes = nor->addr_nbytes;
read_dummy = nor->read_dummy;
read_proto = nor->read_proto;
rdesc = nor->dirmap.rdesc;
@@ -54,7 +54,7 @@ int spi_nor_otp_read_secr(struct spi_nor *nor, loff_t addr, size_t len, u8 *buf)
ret = spi_nor_read_data(nor, addr, len, buf);
nor->read_opcode = read_opcode;
- nor->addr_width = addr_width;
+ nor->addr_nbytes = addr_nbytes;
nor->read_dummy = read_dummy;
nor->read_proto = read_proto;
nor->dirmap.rdesc = rdesc;
@@ -85,11 +85,11 @@ int spi_nor_otp_write_secr(struct spi_nor *nor, loff_t addr, size_t len,
{
enum spi_nor_protocol write_proto;
struct spi_mem_dirmap_desc *wdesc;
- u8 addr_width, program_opcode;
+ u8 addr_nbytes, program_opcode;
int ret, written;
program_opcode = nor->program_opcode;
- addr_width = nor->addr_width;
+ addr_nbytes = nor->addr_nbytes;
write_proto = nor->write_proto;
wdesc = nor->dirmap.wdesc;
@@ -113,7 +113,7 @@ int spi_nor_otp_write_secr(struct spi_nor *nor, loff_t addr, size_t len,
out:
nor->program_opcode = program_opcode;
- nor->addr_width = addr_width;
+ nor->addr_nbytes = addr_nbytes;
nor->write_proto = write_proto;
nor->dirmap.wdesc = wdesc;
@@ -134,7 +134,7 @@ struct sfdp_4bait {
/**
* spi_nor_read_raw() - raw read of serial flash memory. read_opcode,
- * addr_width and read_dummy members of the struct spi_nor
+ * addr_nbytes and read_dummy members of the struct spi_nor
* should be previously
* set.
* @nor: pointer to a 'struct spi_nor'
@@ -178,21 +178,21 @@ static int spi_nor_read_raw(struct spi_nor *nor, u32 addr, size_t len, u8 *buf)
static int spi_nor_read_sfdp(struct spi_nor *nor, u32 addr,
size_t len, void *buf)
{
- u8 addr_width, read_opcode, read_dummy;
+ u8 addr_nbytes, read_opcode, read_dummy;
int ret;
read_opcode = nor->read_opcode;
- addr_width = nor->addr_width;
+ addr_nbytes = nor->addr_nbytes;
read_dummy = nor->read_dummy;
nor->read_opcode = SPINOR_OP_RDSFDP;
- nor->addr_width = 3;
+ nor->addr_nbytes = 3;
nor->read_dummy = 8;
ret = spi_nor_read_raw(nor, addr, len, buf);
nor->read_opcode = read_opcode;
- nor->addr_width = addr_width;
+ nor->addr_nbytes = addr_nbytes;
nor->read_dummy = read_dummy;
return ret;
@@ -462,11 +462,11 @@ static int spi_nor_parse_bfpt(struct spi_nor *nor,
switch (bfpt.dwords[BFPT_DWORD(1)] & BFPT_DWORD1_ADDRESS_BYTES_MASK) {
case BFPT_DWORD1_ADDRESS_BYTES_3_ONLY:
case BFPT_DWORD1_ADDRESS_BYTES_3_OR_4:
- nor->addr_width = 3;
+ nor->addr_nbytes = 3;
break;
case BFPT_DWORD1_ADDRESS_BYTES_4_ONLY:
- nor->addr_width = 4;
+ nor->addr_nbytes = 4;
break;
default:
@@ -637,12 +637,12 @@ static int spi_nor_parse_bfpt(struct spi_nor *nor,
}
/**
- * spi_nor_smpt_addr_width() - return the address width used in the
+ * spi_nor_smpt_addr_nbytes() - return the number of address bytes used in the
* configuration detection command.
* @nor: pointer to a 'struct spi_nor'
* @settings: configuration detection command descriptor, dword1
*/
-static u8 spi_nor_smpt_addr_width(const struct spi_nor *nor, const u32 settings)
+static u8 spi_nor_smpt_addr_nbytes(const struct spi_nor *nor, const u32 settings)
{
switch (settings & SMPT_CMD_ADDRESS_LEN_MASK) {
case SMPT_CMD_ADDRESS_LEN_0:
@@ -653,7 +653,7 @@ static u8 spi_nor_smpt_addr_width(const struct spi_nor *nor, const u32 settings)
return 4;
case SMPT_CMD_ADDRESS_LEN_USE_CURRENT:
default:
- return nor->addr_width;
+ return nor->addr_nbytes;
}
}
@@ -690,7 +690,7 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt,
u32 addr;
int err;
u8 i;
- u8 addr_width, read_opcode, read_dummy;
+ u8 addr_nbytes, read_opcode, read_dummy;
u8 read_data_mask, map_id;
/* Use a kmalloc'ed bounce buffer to guarantee it is DMA-able. */
@@ -698,7 +698,7 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt,
if (!buf)
return ERR_PTR(-ENOMEM);
- addr_width = nor->addr_width;
+ addr_nbytes = nor->addr_nbytes;
read_dummy = nor->read_dummy;
read_opcode = nor->read_opcode;
@@ -709,7 +709,7 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt,
break;
read_data_mask = SMPT_CMD_READ_DATA(smpt[i]);
- nor->addr_width = spi_nor_smpt_addr_width(nor, smpt[i]);
+ nor->addr_nbytes = spi_nor_smpt_addr_nbytes(nor, smpt[i]);
nor->read_dummy = spi_nor_smpt_read_dummy(nor, smpt[i]);
nor->read_opcode = SMPT_CMD_OPCODE(smpt[i]);
addr = smpt[i + 1];
@@ -756,7 +756,7 @@ static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt,
/* fall through */
out:
kfree(buf);
- nor->addr_width = addr_width;
+ nor->addr_nbytes = addr_nbytes;
nor->read_dummy = read_dummy;
nor->read_opcode = read_opcode;
return ret;
@@ -1044,7 +1044,7 @@ static int spi_nor_parse_4bait(struct spi_nor *nor,
/*
* We need at least one 4-byte op code per read, program and erase
* operation; the .read(), .write() and .erase() hooks share the
- * nor->addr_width value.
+ * nor->addr_nbytes value.
*/
if (!read_hwcaps || !pp_hwcaps || !erase_mask)
goto out;
@@ -1098,7 +1098,7 @@ static int spi_nor_parse_4bait(struct spi_nor *nor,
* Spansion memory. However this quirk is no longer needed with new
* SFDP compliant memories.
*/
- nor->addr_width = 4;
+ nor->addr_nbytes = 4;
nor->flags |= SNOR_F_4B_OPCODES | SNOR_F_HAS_4BAIT;
/* fall through */
@@ -31,7 +31,7 @@
.sector_size = (8 * (_page_size)), \
.n_sectors = (_n_sectors), \
.page_size = (_page_size), \
- .addr_width = 3, \
+ .addr_nbytes = 3, \
.flags = SPI_NOR_NO_FR
/* Xilinx S3AN share MFR with Atmel SPI NOR */
@@ -353,7 +353,7 @@ struct spi_nor_flash_parameter;
* @bouncebuf_size: size of the bounce buffer
* @info: SPI NOR part JEDEC MFR ID and other info
* @manufacturer: SPI NOR manufacturer
- * @addr_width: number of address bytes
+ * @addr_nbytes: number of address bytes
* @erase_opcode: the opcode for erasing a sector
* @read_opcode: the read opcode
* @read_dummy: the dummy needed by the read operation
@@ -382,7 +382,7 @@ struct spi_nor {
size_t bouncebuf_size;
const struct flash_info *info;
const struct spi_nor_manufacturer *manufacturer;
- u8 addr_width;
+ u8 addr_nbytes;
u8 erase_opcode;
u8 read_opcode;
u8 read_dummy;
Address width was an unfortunate name, as it means the number of IO lines used for the address, whereas in the code it is used as the number of address bytes. s/addr_width/addr_nbytes throughout the entire SPI NOR framework. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> --- drivers/mtd/spi-nor/controllers/aspeed-smc.c | 6 +-- drivers/mtd/spi-nor/controllers/hisi-sfc.c | 2 +- drivers/mtd/spi-nor/controllers/nxp-spifi.c | 8 ++-- drivers/mtd/spi-nor/core.c | 46 ++++++++++---------- drivers/mtd/spi-nor/core.h | 12 ++--- drivers/mtd/spi-nor/issi.c | 2 +- drivers/mtd/spi-nor/otp.c | 12 ++--- drivers/mtd/spi-nor/sfdp.c | 32 +++++++------- drivers/mtd/spi-nor/xilinx.c | 2 +- include/linux/mtd/spi-nor.h | 4 +- 10 files changed, 63 insertions(+), 63 deletions(-)