diff mbox series

[1/5] mtd: rawnand: omap: Aggregate the HW configuration of the ELM

Message ID 20210610134906.3503303-2-miquel.raynal@bootlin.com
State Accepted
Headers show
Series AM335x large page support | expand

Commit Message

Miquel Raynal June 10, 2021, 1:49 p.m. UTC 
Instead of calling elm_config() for each possible BCH configuration,
just save the BCH configuration that must be applied and use it in a
single call at the bottom.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 drivers/mtd/nand/raw/omap2.c | 32 ++++++++++++--------------------
 1 file changed, 12 insertions(+), 20 deletions(-)

Comments

Miquel Raynal June 11, 2021, 7:01 p.m. UTC | #1 
On Thu, 2021-06-10 at 13:49:02 UTC, Miquel Raynal wrote:
> Instead of calling elm_config() for each possible BCH configuration,
> just save the BCH configuration that must be applied and use it in a
> single call at the bottom.
> 
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

Applied to https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git nand/next.

Miquel
diff mbox series

Patch

diff --git a/drivers/mtd/nand/raw/omap2.c b/drivers/mtd/nand/raw/omap2.c
index 512f60780a50..eb8b5e10ab6e 100644
--- a/drivers/mtd/nand/raw/omap2.c
+++ b/drivers/mtd/nand/raw/omap2.c
@@ -1915,6 +1915,7 @@  static int omap_nand_attach_chip(struct nand_chip *chip)
 	struct omap_nand_info *info = mtd_to_omap(mtd);
 	struct device *dev = &info->pdev->dev;
 	int min_oobbytes = BADBLOCK_MARKER_LENGTH;
+	int elm_bch_strength = -1;
 	int oobbytes_per_step;
 	dma_cap_mask_t mask;
 	int err;
@@ -2068,12 +2069,7 @@  static int omap_nand_attach_chip(struct nand_chip *chip)
 		chip->ecc.write_subpage	= omap_write_subpage_bch;
 		mtd_set_ooblayout(mtd, &omap_ooblayout_ops);
 		oobbytes_per_step	= chip->ecc.bytes;
-
-		err = elm_config(info->elm_dev, BCH4_ECC,
-				 mtd->writesize / chip->ecc.size,
-				 chip->ecc.size, chip->ecc.bytes);
-		if (err < 0)
-			return err;
+		elm_bch_strength = BCH4_ECC;
 		break;
 
 	case OMAP_ECC_BCH8_CODE_HW_DETECTION_SW:
@@ -2110,13 +2106,7 @@  static int omap_nand_attach_chip(struct nand_chip *chip)
 		chip->ecc.write_subpage	= omap_write_subpage_bch;
 		mtd_set_ooblayout(mtd, &omap_ooblayout_ops);
 		oobbytes_per_step	= chip->ecc.bytes;
-
-		err = elm_config(info->elm_dev, BCH8_ECC,
-				 mtd->writesize / chip->ecc.size,
-				 chip->ecc.size, chip->ecc.bytes);
-		if (err < 0)
-			return err;
-
+		elm_bch_strength = BCH8_ECC;
 		break;
 
 	case OMAP_ECC_BCH16_CODE_HW:
@@ -2132,19 +2122,21 @@  static int omap_nand_attach_chip(struct nand_chip *chip)
 		chip->ecc.write_subpage	= omap_write_subpage_bch;
 		mtd_set_ooblayout(mtd, &omap_ooblayout_ops);
 		oobbytes_per_step	= chip->ecc.bytes;
-
-		err = elm_config(info->elm_dev, BCH16_ECC,
-				 mtd->writesize / chip->ecc.size,
-				 chip->ecc.size, chip->ecc.bytes);
-		if (err < 0)
-			return err;
-
+		elm_bch_strength = BCH16_ECC;
 		break;
 	default:
 		dev_err(dev, "Invalid or unsupported ECC scheme\n");
 		return -EINVAL;
 	}
 
+	if (elm_bch_strength >= 0) {
+		err = elm_config(info->elm_dev, elm_bch_strength,
+				 mtd->writesize / chip->ecc.size,
+				 chip->ecc.size, chip->ecc.bytes);
+		if (err < 0)
+			return err;
+	}
+
 	/* Check if NAND device's OOB is enough to store ECC signatures */
 	min_oobbytes += (oobbytes_per_step *
 			 (mtd->writesize / chip->ecc.size));