diff mbox series

[1/1] mtd: spinand: Add support for new Micron SPI NAND devices

Message ID 20191209064223.10003-2-sshivamurthy@micron.com
State Changes Requested
Delegated to: Miquel Raynal
Headers show
Series Add new series Micron SPI NAND devices | expand

Commit Message

Shivamurthy Shastri Dec. 9, 2019, 6:42 a.m. UTC 
From: Shivamurthy Shastri <sshivamurthy@micron.com>

Add device table for new Micron SPI NAND devices. While at it, add
support to the multi-die selection. Also, generalize the OOB layout
structure and function names.

Signed-off-by: Shivamurthy Shastri <sshivamurthy@micron.com>
---
 drivers/mtd/nand/spi/micron.c | 135 ++++++++++++++++++++++++++++++----
 1 file changed, 121 insertions(+), 14 deletions(-)

Comments

Miquel Raynal Jan. 9, 2020, 3:48 p.m. UTC | #1 
Hi Shiva,

shiva.linuxworks@gmail.com wrote on Mon,  9 Dec 2019 07:42:23 +0100:

> From: Shivamurthy Shastri <sshivamurthy@micron.com>
> 
> Add device table for new Micron SPI NAND devices. While at it, add
> support to the multi-die selection. Also, generalize the OOB layout
> structure and function names.

Sorry for the delay. I am fine with this patch mostly, but could we
split it please?

O/ Disable continuous read feature (one typo, see below). I think this
might be considered as a fix.

1/ Generalize the OOB layout structure and function names.
2/ Add support for all the parts.
3/ Add multi-die support (one comment below about that).

As a general rule of thumb, small patches, doing one logic change are
much easier and quick to review and accept.


> +static int micron_select_target(struct spinand_device *spinand,
> +				unsigned int target)
> +{
> +	struct spi_mem_op op = SPINAND_SET_FEATURE_OP(0xd0,
> +						      spinand->scratchbuf);
> +
> +	if (target == 1)
> +		*spinand->scratchbuf = 0x40;

Please define 0x40 and explain clearly with a comment that this is
multi-die selection.

> +
> +	return spi_mem_exec_op(spinand->spimem, &op);
> +}
> +

[...]

> +static int micron_spinand_init(struct spinand_device *spinand)
> +{
> +	/*
> +	 * M70A series device enables Continuos Read feature on Power-up,
> +	 * which is not supported here. Making this BIT disable will avoid
> +	 * any possible failure.

What about:

           M70A device series enable Continuous Read feature at
           power-up, which is not supported. Disable this bit to
	   avoid any possible failure.

> +	 */
> +	return spinand_upd_cfg(spinand, CFG_QUAD_ENABLE, 0);
> +}
> +
>  static const struct spinand_manufacturer_ops micron_spinand_manuf_ops = {
>  	.detect = micron_spinand_detect,
> +	.init = micron_spinand_init,
>  };
>  
>  const struct spinand_manufacturer micron_spinand_manufacturer = {

Thanks,
Miquèl
diff mbox series

Patch

diff --git a/drivers/mtd/nand/spi/micron.c b/drivers/mtd/nand/spi/micron.c
index 7d7b1f7fcf71..bce5da21d96c 100644
--- a/drivers/mtd/nand/spi/micron.c
+++ b/drivers/mtd/nand/spi/micron.c
@@ -34,38 +34,38 @@  static SPINAND_OP_VARIANTS(update_cache_variants,
 		SPINAND_PROG_LOAD_X4(false, 0, NULL, 0),
 		SPINAND_PROG_LOAD(false, 0, NULL, 0));
 
-static int mt29f2g01abagd_ooblayout_ecc(struct mtd_info *mtd, int section,
-					struct mtd_oob_region *region)
+static int micron_8_ooblayout_ecc(struct mtd_info *mtd, int section,
+				  struct mtd_oob_region *region)
 {
 	if (section)
 		return -ERANGE;
 
-	region->offset = 64;
-	region->length = 64;
+	region->offset = mtd->oobsize / 2;
+	region->length = mtd->oobsize / 2;
 
 	return 0;
 }
 
-static int mt29f2g01abagd_ooblayout_free(struct mtd_info *mtd, int section,
-					 struct mtd_oob_region *region)
+static int micron_8_ooblayout_free(struct mtd_info *mtd, int section,
+				   struct mtd_oob_region *region)
 {
 	if (section)
 		return -ERANGE;
 
 	/* Reserve 2 bytes for the BBM. */
 	region->offset = 2;
-	region->length = 62;
+	region->length = (mtd->oobsize / 2) - 2;
 
 	return 0;
 }
 
-static const struct mtd_ooblayout_ops mt29f2g01abagd_ooblayout = {
-	.ecc = mt29f2g01abagd_ooblayout_ecc,
-	.free = mt29f2g01abagd_ooblayout_free,
+static const struct mtd_ooblayout_ops micron_8_ooblayout = {
+	.ecc = micron_8_ooblayout_ecc,
+	.free = micron_8_ooblayout_free,
 };
 
-static int mt29f2g01abagd_ecc_get_status(struct spinand_device *spinand,
-					 u8 status)
+static int micron_8_ecc_get_status(struct spinand_device *spinand,
+				   u8 status)
 {
 	switch (status & MICRON_STATUS_ECC_MASK) {
 	case STATUS_ECC_NO_BITFLIPS:
@@ -90,7 +90,20 @@  static int mt29f2g01abagd_ecc_get_status(struct spinand_device *spinand,
 	return -EINVAL;
 }
 
+static int micron_select_target(struct spinand_device *spinand,
+				unsigned int target)
+{
+	struct spi_mem_op op = SPINAND_SET_FEATURE_OP(0xd0,
+						      spinand->scratchbuf);
+
+	if (target == 1)
+		*spinand->scratchbuf = 0x40;
+
+	return spi_mem_exec_op(spinand->spimem, &op);
+}
+
 static const struct spinand_info micron_spinand_table[] = {
+	/* M79A 2Gb 3.3V */
 	SPINAND_INFO("MT29F2G01ABAGD", 0x24,
 		     NAND_MEMORG(1, 2048, 128, 64, 2048, 40, 2, 1, 1),
 		     NAND_ECCREQ(8, 512),
@@ -98,8 +111,91 @@  static const struct spinand_info micron_spinand_table[] = {
 					      &write_cache_variants,
 					      &update_cache_variants),
 		     0,
-		     SPINAND_ECCINFO(&mt29f2g01abagd_ooblayout,
-				     mt29f2g01abagd_ecc_get_status)),
+		     SPINAND_ECCINFO(&micron_8_ooblayout,
+				     micron_8_ecc_get_status)),
+	/* M79A 2Gb 1.8V */
+	SPINAND_INFO("MT29F2G01ABBGD", 0x25,
+		     NAND_MEMORG(1, 2048, 128, 64, 2048, 40, 2, 1, 1),
+		     NAND_ECCREQ(8, 512),
+		     SPINAND_INFO_OP_VARIANTS(&read_cache_variants,
+					      &write_cache_variants,
+					      &update_cache_variants),
+		     0,
+		     SPINAND_ECCINFO(&micron_8_ooblayout,
+				     micron_8_ecc_get_status)),
+	/* M78A 1Gb 3.3V */
+	SPINAND_INFO("MT29F1G01ABAFD", 0x14,
+		     NAND_MEMORG(1, 2048, 128, 64, 1024, 20, 1, 1, 1),
+		     NAND_ECCREQ(8, 512),
+		     SPINAND_INFO_OP_VARIANTS(&read_cache_variants,
+					      &write_cache_variants,
+					      &update_cache_variants),
+		     0,
+		     SPINAND_ECCINFO(&micron_8_ooblayout,
+				     micron_8_ecc_get_status)),
+	/* M78A 1Gb 1.8V */
+	SPINAND_INFO("MT29F1G01ABAFD", 0x15,
+		     NAND_MEMORG(1, 2048, 128, 64, 1024, 20, 1, 1, 1),
+		     NAND_ECCREQ(8, 512),
+		     SPINAND_INFO_OP_VARIANTS(&read_cache_variants,
+					      &write_cache_variants,
+					      &update_cache_variants),
+		     0,
+		     SPINAND_ECCINFO(&micron_8_ooblayout,
+				     micron_8_ecc_get_status)),
+	/* M79A 4Gb 3.3V */
+	SPINAND_INFO("MT29F4G01ADAGD", 0x36,
+		     NAND_MEMORG(1, 2048, 128, 64, 2048, 80, 2, 1, 2),
+		     NAND_ECCREQ(8, 512),
+		     SPINAND_INFO_OP_VARIANTS(&read_cache_variants,
+					      &write_cache_variants,
+					      &update_cache_variants),
+		     0,
+		     SPINAND_ECCINFO(&micron_8_ooblayout,
+				     micron_8_ecc_get_status),
+		     SPINAND_SELECT_TARGET(micron_select_target)),
+	/* M70A 4Gb 3.3V */
+	SPINAND_INFO("MT29F4G01ABAFD", 0x34,
+		     NAND_MEMORG(1, 4096, 256, 64, 2048, 40, 1, 1, 1),
+		     NAND_ECCREQ(8, 512),
+		     SPINAND_INFO_OP_VARIANTS(&read_cache_variants,
+					      &write_cache_variants,
+					      &update_cache_variants),
+		     0,
+		     SPINAND_ECCINFO(&micron_8_ooblayout,
+				     micron_8_ecc_get_status)),
+	/* M70A 4Gb 1.8V */
+	SPINAND_INFO("MT29F4G01ABBFD", 0x35,
+		     NAND_MEMORG(1, 4096, 256, 64, 2048, 40, 1, 1, 1),
+		     NAND_ECCREQ(8, 512),
+		     SPINAND_INFO_OP_VARIANTS(&read_cache_variants,
+					      &write_cache_variants,
+					      &update_cache_variants),
+		     0,
+		     SPINAND_ECCINFO(&micron_8_ooblayout,
+				     micron_8_ecc_get_status)),
+	/* M70A 8Gb 3.3V */
+	SPINAND_INFO("MT29F8G01ADAFD", 0x46,
+		     NAND_MEMORG(1, 4096, 256, 64, 2048, 40, 1, 1, 2),
+		     NAND_ECCREQ(8, 512),
+		     SPINAND_INFO_OP_VARIANTS(&read_cache_variants,
+					      &write_cache_variants,
+					      &update_cache_variants),
+		     0,
+		     SPINAND_ECCINFO(&micron_8_ooblayout,
+				     micron_8_ecc_get_status),
+		     SPINAND_SELECT_TARGET(micron_select_target)),
+	/* M70A 8Gb 1.8V */
+	SPINAND_INFO("MT29F8G01ADBFD", 0x47,
+		     NAND_MEMORG(1, 4096, 256, 64, 2048, 40, 1, 1, 2),
+		     NAND_ECCREQ(8, 512),
+		     SPINAND_INFO_OP_VARIANTS(&read_cache_variants,
+					      &write_cache_variants,
+					      &update_cache_variants),
+		     0,
+		     SPINAND_ECCINFO(&micron_8_ooblayout,
+				     micron_8_ecc_get_status),
+		     SPINAND_SELECT_TARGET(micron_select_target)),
 };
 
 static int micron_spinand_detect(struct spinand_device *spinand)
@@ -122,8 +218,19 @@  static int micron_spinand_detect(struct spinand_device *spinand)
 	return 1;
 }
 
+static int micron_spinand_init(struct spinand_device *spinand)
+{
+	/*
+	 * M70A series device enables Continuos Read feature on Power-up,
+	 * which is not supported here. Making this BIT disable will avoid
+	 * any possible failure.
+	 */
+	return spinand_upd_cfg(spinand, CFG_QUAD_ENABLE, 0);
+}
+
 static const struct spinand_manufacturer_ops micron_spinand_manuf_ops = {
 	.detect = micron_spinand_detect,
+	.init = micron_spinand_init,
 };
 
 const struct spinand_manufacturer micron_spinand_manufacturer = {