diff mbox series

[mvebu-dt64] arm64: dts: marvell: armada-37xx: Add DTS file for Turris Mox

Message ID 20180830152326.15562-1-marek.behun@nic.cz
State New
Headers show
Series [mvebu-dt64] arm64: dts: marvell: armada-37xx: Add DTS file for Turris Mox | expand

Commit Message

Marek Behun Aug. 30, 2018, 3:23 p.m. UTC
This adds support for the Turris Mox board from CZ.NIC.

Turris Mox is as modular router based on the Armada 3720 SOC (same as
EspressoBin).

The basic module can be extended by different modules.
When those modules are connected, U-Boot shall patch this device-tree
by enabling nodes corresponding to those modules.

Signed-off-by: Marek BehĂșn <marek.behun@nic.cz>
---
 .../arm/marvell/armada-3720-turris-mox.txt         |   6 +
 arch/arm64/boot/dts/marvell/Makefile               |   1 +
 .../boot/dts/marvell/armada-3720-turris-mox.dts    | 817 +++++++++++++++++++++
 3 files changed, 824 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-3720-turris-mox.txt
 create mode 100644 arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts

Comments

Andrew Lunn Aug. 30, 2018, 3:57 p.m. UTC | #1
> +	switch0@10 {
> +		compatible = "marvell,mv88e6190";
> +		reg = <0x10 0>;

MDO reg should have a single value, i think.

> +	switch0@2 {
> +		status = "disabled";
...
> +	};
> +
> +	switch1@11 {
> +		status = "disabled";
...
> +	};
> +
> +	switch1@2 {
> +		status = "disabled";
...
> +	};
> +
> +	switch2@12 {
> +		status = "disabled";
...
> +	};
> +
> +	switch2@2 {
> +		status = "disabled";
...
> +	};
> +};

I'm assuming the boatloader is probing the hardware, and then enabling
what it finds? This is a poor mans DT fragments. Lets see that Rob has
to say about this.

> +	moxtet@1 {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		compatible = "cznic,moxtet";
> +		reg = <1>;
> +		devrst-gpio = <&gpiosb 2 GPIO_ACTIVE_LOW>;
> +		spi-max-frequency = <1000000>;
> +		spi-cpol;
> +		spi-cpha;
> +
> +		moxtet_sfp: moxtet-sfp@0 {
> +			compatible = "cznic,moxtet-gpio";
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +			reg = <0>;
> +			moxtet,id = <1>;
> +			moxtet,input-mask = <0x7>;
> +			moxtet,output-mask = <0x3>;
> +			status = "disabled";
> +		};
> +	};
> +};

Have the drivers for this been merged yet?

     Andrew
Marek Behun Aug. 30, 2018, 4:16 p.m. UTC | #2
On Thu, 30 Aug 2018 17:57:01 +0200
Andrew Lunn <andrew@lunn.ch> wrote:

> > +	switch0@10 {
> > +		compatible = "marvell,mv88e6190";
> > +		reg = <0x10 0>;  
> 
> MDO reg should have a single value, i think.
> 
> > +	switch0@2 {
> > +		status = "disabled";  
> ...
> > +	};
> > +
> > +	switch1@11 {
> > +		status = "disabled";  
> ...
> > +	};
> > +
> > +	switch1@2 {
> > +		status = "disabled";  
> ...
> > +	};
> > +
> > +	switch2@12 {
> > +		status = "disabled";  
> ...
> > +	};
> > +
> > +	switch2@2 {
> > +		status = "disabled";  
> ...
> > +	};
> > +};  
> 
> I'm assuming the boatloader is probing the hardware, and then enabling
> what it finds? This is a poor mans DT fragments. Lets see that Rob has
> to say about this.

The bootloader can read which hardware is connected via a SPI shift
register. Three switch modules can be connected in DSA, in these
possibilities:
  6190
  6190-6190
  6190-6190-6190
  6141
  6190-6141
  6190-6190-6141
At first I had the Linux's device tree completely without the switch
nodes, and I generated the nodes via libfdt in u-boot, but the code was
terrible to read. This way u-boot's code is nice and readable.

> 
> > +	moxtet@1 {
> > +		#address-cells = <1>;
> > +		#size-cells = <0>;
> > +		compatible = "cznic,moxtet";
> > +		reg = <1>;
> > +		devrst-gpio = <&gpiosb 2 GPIO_ACTIVE_LOW>;
> > +		spi-max-frequency = <1000000>;
> > +		spi-cpol;
> > +		spi-cpha;
> > +
> > +		moxtet_sfp: moxtet-sfp@0 {
> > +			compatible = "cznic,moxtet-gpio";
> > +			gpio-controller;
> > +			#gpio-cells = <2>;
> > +			reg = <0>;
> > +			moxtet,id = <1>;
> > +			moxtet,input-mask = <0x7>;
> > +			moxtet,output-mask = <0x3>;
> > +			status = "disabled";
> > +		};
> > +	};
> > +};  
> 
> Have the drivers for this been merged yet?

No, I sent the patches today as this one.

> 
>      Andrew
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/arm/marvell/armada-3720-turris-mox.txt b/Documentation/devicetree/bindings/arm/marvell/armada-3720-turris-mox.txt
new file mode 100644
index 000000000000..408fc07a9bbf
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/marvell/armada-3720-turris-mox.txt
@@ -0,0 +1,6 @@ 
+CZ.NIC's Turris Mox SOHO router Device Tree Bindings
+----------------------------------------------------
+
+Required root node property:
+
+compatible: must contain "cznic,turris-mox"
diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index ea9d49f2a911..1dd89d1bf8ad 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -2,6 +2,7 @@ 
 # Mvebu SoC Family
 dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-turris-mox.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
new file mode 100644
index 000000000000..9267ae96f14f
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
@@ -0,0 +1,817 @@ 
+// SPDX-License-Identifier: GPL-2.0+ or X11
+/*
+ * Device Tree file for CZ.NIC Turris Mox Board
+ * 2018 by Marek Behun <marek.behun@nic.cz>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "armada-372x.dtsi"
+
+/ {
+	model = "CZ.NIC Turris Mox Board";
+	compatible = "cznic,turris-mox", "marvell,armada3720",
+		     "marvell,armada3710";
+
+	aliases {
+		spi0 = &spi0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		red {
+			gpios = <&gpiosb 21 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		reset_button {
+			label = "reset";
+			linux,code = <BTN_MISC>;
+			gpios = <&gpiosb 20 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+	};
+
+	exp_usb3_vbus: usb3-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb3-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-always-on;
+		gpio = <&gpiosb 0 GPIO_ACTIVE_HIGH>;
+	};
+
+	usb3_phy: usb3-phy {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&exp_usb3_vbus>;
+	};
+
+	vsdc_reg: vsdc_reg {
+		compatible = "regulator-gpio";
+		regulator-name = "vsdc";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+
+		gpios = <&gpiosb 23 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0>;
+		states = <1800000 0x1
+			  3300000 0x0>;
+		enable-active-high;
+	};
+
+	vsdio_reg: vsdio_reg {
+		compatible = "regulator-gpio";
+		regulator-name = "vsdio";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+
+		gpios = <&gpiosb 22 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0>;
+		states = <1800000 0x1
+			  3300000 0x0>;
+		enable-active-high;
+	};
+
+	sfp: sfp {
+		compatible = "sff,sfp+";
+		i2c-bus = <&i2c0>;
+		los-gpio = <&moxtet_sfp 0 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpio = <&moxtet_sfp 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpio = <&moxtet_sfp 2 GPIO_ACTIVE_LOW>;
+		tx-disable-gpio = <&moxtet_sfp 3 GPIO_ACTIVE_HIGH>;
+		rate-select0-gpio = <&moxtet_sfp 4 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+};
+
+&pinctrl_nb {
+	spi_cs1_pins: spi-cs1-pins {
+		groups = "spi_cs1";
+		function = "spi";
+	};
+
+	sdio0_pins: sdio0-pins {
+		groups = "sdio0";
+		function = "sdio";
+	};
+};
+
+&pinctrl_sb {
+	sdio_sb_pins: sdio-sb-pins {
+		groups = "sdio_sb";
+		function = "sdio";
+	};
+
+	smi_pins: smi-pins {
+		groups = "smi";
+		function = "smi";
+	};
+
+	pcie_pins: pcie1-pins {
+		groups = "pcie1";
+		function = "gpio";
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	status = "okay";
+
+	rtc@6f {
+		compatible = "microchip,mcp7940x";
+		reg = <0x6f>;
+	};
+};
+
+&pcie0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_pins>;
+	status = "okay";
+	max-link-speed = <2>;
+	reset-gpio = <&gpiosb 3 GPIO_ACTIVE_HIGH>;
+
+	/* this shall be enabled by u-boot if the PCIe module is present */
+	status = "disabled";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&eth0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	phy-mode = "rgmii-id";
+	phy = <&phy1>;
+	status = "okay";
+};
+
+&eth1 {
+	phy-mode = "1000base-x";
+	managed = "in-band-status";
+};
+
+&mdio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&smi_pins>;
+	status = "okay";
+
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+
+	switch0@10 {
+		compatible = "marvell,mv88e6190";
+		reg = <0x10 0>;
+		dsa,member = <0 0>;
+		interrupt-parent = <&gpiosb>;
+		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+		status = "disabled";
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch0phy1: switch0phy1@1 {
+				reg = <0x1>;
+			};
+
+			switch0phy2: switch0phy2@2 {
+				reg = <0x2>;
+			};
+
+			switch0phy3: switch0phy3@3 {
+				reg = <0x3>;
+			};
+
+			switch0phy4: switch0phy4@4 {
+				reg = <0x4>;
+			};
+
+			switch0phy5: switch0phy5@5 {
+				reg = <0x5>;
+			};
+
+			switch0phy6: switch0phy6@6 {
+				reg = <0x6>;
+			};
+
+			switch0phy7: switch0phy7@7 {
+				reg = <0x7>;
+			};
+
+			switch0phy8: switch0phy8@8 {
+				reg = <0x8>;
+			};
+		};
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@1 {
+				reg = <0x1>;
+				label = "lan1";
+				phy-handle = <&switch0phy1>;
+			};
+
+			port@2 {
+				reg = <0x2>;
+				label = "lan2";
+				phy-handle = <&switch0phy2>;
+			};
+
+			port@3 {
+				reg = <0x3>;
+				label = "lan3";
+				phy-handle = <&switch0phy3>;
+			};
+
+			port@4 {
+				reg = <0x4>;
+				label = "lan4";
+				phy-handle = <&switch0phy4>;
+			};
+
+			port@5 {
+				reg = <0x5>;
+				label = "lan5";
+				phy-handle = <&switch0phy5>;
+			};
+
+			port@6 {
+				reg = <0x6>;
+				label = "lan6";
+				phy-handle = <&switch0phy6>;
+			};
+
+			port@7 {
+				reg = <0x7>;
+				label = "lan7";
+				phy-handle = <&switch0phy7>;
+			};
+
+			port@8 {
+				reg = <0x8>;
+				label = "lan8";
+				phy-handle = <&switch0phy8>;
+			};
+
+			port@9 {
+				reg = <0x9>;
+				label = "cpu";
+				ethernet = <&eth1>;
+			};
+
+			switch0port10: port@a {
+				reg = <0xa>;
+				label = "dsa";
+				phy-mode = "2500base-x";
+				link = <&switch1port9 &switch2port9>;
+				status = "disabled";
+			};
+
+			port-sfp@a {
+				reg = <0xa>;
+				label = "sfp";
+				sfp = <&sfp>;
+				phy-mode = "sgmii";
+				managed = "in-band-status";
+				status = "disabled";
+			};
+		};
+	};
+
+	switch0@2 {
+		compatible = "marvell,mv88e6085";
+		reg = <0x2 0>;
+		dsa,member = <0 0>;
+		interrupt-parent = <&gpiosb>;
+		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+		status = "disabled";
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch0phy1_topaz: switch0phy1@11 {
+				reg = <0x11>;
+			};
+
+			switch0phy2_topaz: switch0phy2@12 {
+				reg = <0x12>;
+			};
+
+			switch0phy3_topaz: switch0phy3@13 {
+				reg = <0x13>;
+			};
+
+			switch0phy4_topaz: switch0phy4@14 {
+				reg = <0x14>;
+			};
+		};
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@1 {
+				reg = <0x1>;
+				label = "lan1";
+				phy-handle = <&switch0phy1_topaz>;
+			};
+
+			port@2 {
+				reg = <0x2>;
+				label = "lan2";
+				phy-handle = <&switch0phy2_topaz>;
+			};
+
+			port@3 {
+				reg = <0x3>;
+				label = "lan3";
+				phy-handle = <&switch0phy3_topaz>;
+			};
+
+			port@4 {
+				reg = <0x4>;
+				label = "lan4";
+				phy-handle = <&switch0phy4_topaz>;
+			};
+
+			port@5 {
+				reg = <0x5>;
+				label = "cpu";
+				ethernet = <&eth1>;
+			};
+		};
+	};
+
+	switch1@11 {
+		compatible = "marvell,mv88e6190";
+		reg = <0x11 0>;
+		dsa,member = <0 1>;
+		interrupt-parent = <&gpiosb>;
+		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+		status = "disabled";
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch1phy1: switch1phy1@1 {
+				reg = <0x1>;
+			};
+
+			switch1phy2: switch1phy2@2 {
+				reg = <0x2>;
+			};
+
+			switch1phy3: switch1phy3@3 {
+				reg = <0x3>;
+			};
+
+			switch1phy4: switch1phy4@4 {
+				reg = <0x4>;
+			};
+
+			switch1phy5: switch1phy5@5 {
+				reg = <0x5>;
+			};
+
+			switch1phy6: switch1phy6@6 {
+				reg = <0x6>;
+			};
+
+			switch1phy7: switch1phy7@7 {
+				reg = <0x7>;
+			};
+
+			switch1phy8: switch1phy8@8 {
+				reg = <0x8>;
+			};
+		};
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@1 {
+				reg = <0x1>;
+				label = "lan9";
+				phy-handle = <&switch1phy1>;
+			};
+
+			port@2 {
+				reg = <0x2>;
+				label = "lan10";
+				phy-handle = <&switch1phy2>;
+			};
+
+			port@3 {
+				reg = <0x3>;
+				label = "lan11";
+				phy-handle = <&switch1phy3>;
+			};
+
+			port@4 {
+				reg = <0x4>;
+				label = "lan12";
+				phy-handle = <&switch1phy4>;
+			};
+
+			port@5 {
+				reg = <0x5>;
+				label = "lan13";
+				phy-handle = <&switch1phy5>;
+			};
+
+			port@6 {
+				reg = <0x6>;
+				label = "lan14";
+				phy-handle = <&switch1phy6>;
+			};
+
+			port@7 {
+				reg = <0x7>;
+				label = "lan15";
+				phy-handle = <&switch1phy7>;
+			};
+
+			port@8 {
+				reg = <0x8>;
+				label = "lan16";
+				phy-handle = <&switch1phy8>;
+			};
+
+			switch1port9: port@9 {
+				reg = <0x9>;
+				label = "dsa";
+				phy-mode = "2500base-x";
+				link = <&switch0port10>;
+			};
+
+			switch1port10: port@a {
+				reg = <0xa>;
+				label = "dsa";
+				phy-mode = "2500base-x";
+				link = <&switch2port9>;
+				status = "disabled";
+			};
+
+			port-sfp@a {
+				reg = <0xa>;
+				label = "sfp";
+				sfp = <&sfp>;
+				phy-mode = "sgmii";
+				managed = "in-band-status";
+				status = "disabled";
+			};
+		};
+	};
+
+	switch1@2 {
+		compatible = "marvell,mv88e6085";
+		reg = <0x2 0>;
+		dsa,member = <0 1>;
+		interrupt-parent = <&gpiosb>;
+		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+		status = "disabled";
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch1phy1_topaz: switch1phy1@11 {
+				reg = <0x11>;
+			};
+
+			switch1phy2_topaz: switch1phy2@12 {
+				reg = <0x12>;
+			};
+
+			switch1phy3_topaz: switch1phy3@13 {
+				reg = <0x13>;
+			};
+
+			switch1phy4_topaz: switch1phy4@14 {
+				reg = <0x14>;
+			};
+		};
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@1 {
+				reg = <0x1>;
+				label = "lan9";
+				phy-handle = <&switch1phy1_topaz>;
+			};
+
+			port@2 {
+				reg = <0x2>;
+				label = "lan10";
+				phy-handle = <&switch1phy2_topaz>;
+			};
+
+			port@3 {
+				reg = <0x3>;
+				label = "lan11";
+				phy-handle = <&switch1phy3_topaz>;
+			};
+
+			port@4 {
+				reg = <0x4>;
+				label = "lan12";
+				phy-handle = <&switch1phy4_topaz>;
+			};
+
+			port@5 {
+				reg = <0x5>;
+				label = "dsa";
+				phy-mode = "2500base-x";
+				link = <&switch0port10>;
+			};
+		};
+	};
+
+	switch2@12 {
+		compatible = "marvell,mv88e6190";
+		reg = <0x12 0>;
+		dsa,member = <0 2>;
+		interrupt-parent = <&gpiosb>;
+		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+		status = "disabled";
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch2phy1: switch2phy1@1 {
+				reg = <0x1>;
+			};
+
+			switch2phy2: switch2phy2@2 {
+				reg = <0x2>;
+			};
+
+			switch2phy3: switch2phy3@3 {
+				reg = <0x3>;
+			};
+
+			switch2phy4: switch2phy4@4 {
+				reg = <0x4>;
+			};
+
+			switch2phy5: switch2phy5@5 {
+				reg = <0x5>;
+			};
+
+			switch2phy6: switch2phy6@6 {
+				reg = <0x6>;
+			};
+
+			switch2phy7: switch2phy7@7 {
+				reg = <0x7>;
+			};
+
+			switch2phy8: switch2phy8@8 {
+				reg = <0x8>;
+			};
+		};
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@1 {
+				reg = <0x1>;
+				label = "lan17";
+				phy-handle = <&switch2phy1>;
+			};
+
+			port@2 {
+				reg = <0x2>;
+				label = "lan18";
+				phy-handle = <&switch2phy2>;
+			};
+
+			port@3 {
+				reg = <0x3>;
+				label = "lan19";
+				phy-handle = <&switch2phy3>;
+			};
+
+			port@4 {
+				reg = <0x4>;
+				label = "lan20";
+				phy-handle = <&switch2phy4>;
+			};
+
+			port@5 {
+				reg = <0x5>;
+				label = "lan21";
+				phy-handle = <&switch2phy5>;
+			};
+
+			port@6 {
+				reg = <0x6>;
+				label = "lan22";
+				phy-handle = <&switch2phy6>;
+			};
+
+			port@7 {
+				reg = <0x7>;
+				label = "lan23";
+				phy-handle = <&switch2phy7>;
+			};
+
+			port@8 {
+				reg = <0x8>;
+				label = "lan24";
+				phy-handle = <&switch2phy8>;
+			};
+
+			switch2port9: port@9 {
+				reg = <0x9>;
+				label = "dsa";
+				phy-mode = "2500base-x";
+				link = <&switch1port10 &switch0port10>;
+			};
+
+			port-sfp@a {
+				reg = <0xa>;
+				label = "sfp";
+				sfp = <&sfp>;
+				phy-mode = "sgmii";
+				managed = "in-band-status";
+				status = "disabled";
+			};
+		};
+	};
+
+	switch2@2 {
+		compatible = "marvell,mv88e6085";
+		reg = <0x2 0>;
+		dsa,member = <0 2>;
+		interrupt-parent = <&gpiosb>;
+		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+		status = "disabled";
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch2phy1_topaz: switch2phy1@11 {
+				reg = <0x11>;
+			};
+
+			switch2phy2_topaz: switch2phy2@12 {
+				reg = <0x12>;
+			};
+
+			switch2phy3_topaz: switch2phy3@13 {
+				reg = <0x13>;
+			};
+
+			switch2phy4_topaz: switch2phy4@14 {
+				reg = <0x14>;
+			};
+		};
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@1 {
+				reg = <0x1>;
+				label = "lan17";
+				phy-handle = <&switch2phy1_topaz>;
+			};
+
+			port@2 {
+				reg = <0x2>;
+				label = "lan18";
+				phy-handle = <&switch2phy2_topaz>;
+			};
+
+			port@3 {
+				reg = <0x3>;
+				label = "lan19";
+				phy-handle = <&switch2phy3_topaz>;
+			};
+
+			port@4 {
+				reg = <0x4>;
+				label = "lan20";
+				phy-handle = <&switch2phy4_topaz>;
+			};
+
+			port@5 {
+				reg = <0x5>;
+				label = "dsa";
+				phy-mode = "2500base-x";
+				link = <&switch1port10 &switch0port10>;
+			};
+		};
+	};
+
+};
+
+&sdhci0 {
+	wp-inverted;
+	bus-width = <4>;
+	cd-gpios = <&gpionb 10 GPIO_ACTIVE_HIGH>;
+	vqmmc-supply = <&vsdc_reg>;
+	marvell,pad-type = "sd";
+	status = "okay";
+};
+
+&sdhci1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdio0_pins &sdio_sb_pins>;
+	non-removable;
+	bus-width = <4>;
+	marvell,pad-type = "sd";
+	vqmmc-supply = <&vsdio_reg>;
+	status = "okay";
+};
+
+&spi0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi_quad_pins &spi_cs1_pins>;
+	assigned-clocks = <&nb_periph_clk 7>;
+	assigned-clock-parents = <&tbg 1>;
+	assigned-clock-rates = <20000000>;
+
+	spi-flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <2000000>;
+
+		partition@0 {
+			label = "u-boot";
+			reg = <0x0 0x3f0000>;
+		};
+
+		partition@3f0000 {
+			label = "u-boot-env";
+			reg = <0x180000 0x10000>;
+		};
+
+		partition@400000 {
+			label = "Rescue system";
+			reg = <0x190000 0x670000>;
+		};
+	};
+
+	moxtet@1 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "cznic,moxtet";
+		reg = <1>;
+		devrst-gpio = <&gpiosb 2 GPIO_ACTIVE_LOW>;
+		spi-max-frequency = <1000000>;
+		spi-cpol;
+		spi-cpha;
+
+		moxtet_sfp: moxtet-sfp@0 {
+			compatible = "cznic,moxtet-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+			reg = <0>;
+			moxtet,id = <1>;
+			moxtet,input-mask = <0x7>;
+			moxtet,output-mask = <0x3>;
+			status = "disabled";
+		};
+	};
+};
+
+&usb3 {
+	status = "okay";
+	usb-phy = <&usb3_phy>;
+};