@@ -85,3 +85,15 @@ config PATA_PARPORT_FIT2
you chose to build PATA_PARPORT support into your kernel, you may answer Y
here to build in the protocol driver, otherwise you should answer M
to build it as a loadable module. The module will be called ktti.
+
+config PATA_PARPORT_FIT3
+ tristate "FIT TD-3000 protocol"
+ depends on PATA_PARPORT
+ help
+ This option enables support for the TD-3000 parallel port IDE
+ protocol from Fidelity International Technology. This protocol is
+ used in newer models of their portable disk, CD-ROM and PD/CD
+ devices. If you chose to build PATA_PARPORT support into your kernel, you
+ may answer Y here to build in the protocol driver, otherwise you
+ should answer M to build it as a loadable module. The module will be
+ called fit3.
@@ -13,3 +13,4 @@ obj-$(CONFIG_PATA_PARPORT_BPCK6) += bpck6.o
obj-$(CONFIG_PATA_PARPORT_COMM) += comm.o
obj-$(CONFIG_PATA_PARPORT_DSTR) += dstr.o
obj-$(CONFIG_PATA_PARPORT_FIT2) += fit2.o
+obj-$(CONFIG_PATA_PARPORT_FIT3) += fit3.o
new file mode 100644
@@ -0,0 +1,195 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * fit3.c (c) 1998 Grant R. Guenther <grant@torque.net>
+ * Under the terms of the GNU General Public License.
+ *
+ * fit3.c is a low-level protocol driver for newer models
+ * of the Fidelity International Technology parallel port adapter.
+ * This adapter is used in their TransDisk 3000 portable
+ * hard-drives, as well as CD-ROM, PD-CD and other devices.
+ *
+ * The TD-2000 and certain older devices use a different protocol.
+ * Try the fit2 protocol module with them.
+ *
+ * NB: The FIT adapters do not appear to support the control
+ * registers. So, we map ALT_STATUS to STATUS and NO-OP writes
+ * to the device control register - this means that IDE reset
+ * will not work on these devices.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/wait.h>
+#include <linux/io.h>
+
+#include "pata_parport.h"
+
+#define j44(a, b) (((a >> 3) & 0x0f) | ((b << 1) & 0xf0))
+
+#define w7(byte) out_p(7, byte)
+#define r7() (in_p(7) & 0xff)
+
+/* cont = 0 - access the IDE register file
+ * cont = 1 - access the IDE command set
+ */
+
+static void fit3_write_regr(struct pi_adapter *pi, int cont, int regr, int val)
+{
+ if (cont == 1)
+ return;
+
+ switch (pi->mode) {
+ case 0:
+ case 1:
+ w2(0xc); w0(regr); w2(0x8); w2(0xc);
+ w0(val); w2(0xd);
+ w0(0); w2(0xc);
+ break;
+ case 2:
+ w2(0xc); w0(regr); w2(0x8); w2(0xc);
+ w4(val); w4(0);
+ w2(0xc);
+ break;
+ }
+}
+
+static int fit3_read_regr(struct pi_adapter *pi, int cont, int regr)
+{
+ int a, b;
+
+ if (cont) {
+ if (regr != 6)
+ return 0xff;
+ regr = 7;
+ }
+
+ switch (pi->mode) {
+ case 0:
+ w2(0xc); w0(regr + 0x10); w2(0x8); w2(0xc);
+ w2(0xd); a = r1();
+ w2(0xf); b = r1();
+ w2(0xc);
+ return j44(a, b);
+ case 1:
+ w2(0xc); w0(regr + 0x90); w2(0x8); w2(0xc);
+ w2(0xec); w2(0xee); w2(0xef); a = r0();
+ w2(0xc);
+ return a;
+ case 2:
+ w2(0xc); w0(regr + 0x90); w2(0x8); w2(0xc);
+ w2(0xec);
+ a = r4(); b = r4();
+ w2(0xc);
+ return a;
+ }
+ return -1;
+}
+
+static void fit3_read_block(struct pi_adapter *pi, char *buf, int count)
+{
+ int k, a, b, c, d;
+
+ switch (pi->mode) {
+ case 0:
+ w2(0xc); w0(0x10); w2(0x8); w2(0xc);
+ for (k = 0; k < count / 2; k++) {
+ w2(0xd); a = r1();
+ w2(0xf); b = r1();
+ w2(0xc); c = r1();
+ w2(0xe); d = r1();
+ buf[2 * k] = j44(a, b);
+ buf[2 * k + 1] = j44(c, d);
+ }
+ w2(0xc);
+ break;
+ case 1:
+ w2(0xc); w0(0x90); w2(0x8); w2(0xc);
+ w2(0xec); w2(0xee);
+ for (k = 0; k < count / 2; k++) {
+ w2(0xef); a = r0();
+ w2(0xee); b = r0();
+ buf[2 * k] = a;
+ buf[2 * k + 1] = b;
+ }
+ w2(0xec);
+ w2(0xc);
+ break;
+ case 2:
+ w2(0xc); w0(0x90); w2(0x8); w2(0xc);
+ w2(0xec);
+ for (k = 0; k < count; k++)
+ buf[k] = r4();
+ w2(0xc);
+ break;
+ }
+}
+
+static void fit3_write_block(struct pi_adapter *pi, char *buf, int count)
+{
+ int k;
+
+ switch (pi->mode) {
+ case 0:
+ case 1:
+ w2(0xc); w0(0); w2(0x8); w2(0xc);
+ for (k = 0; k < count/2; k++) {
+ w0(buf[2 * k]); w2(0xd);
+ w0(buf[2 * k + 1]); w2(0xc);
+ }
+ break;
+ case 2:
+ w2(0xc); w0(0); w2(0x8); w2(0xc);
+ for (k = 0; k < count; k++)
+ w4(buf[k]);
+ w2(0xc);
+ break;
+ }
+}
+
+static void fit3_connect(struct pi_adapter *pi)
+{
+ pi->saved_r0 = r0();
+ pi->saved_r2 = r2();
+ w2(0xc); w0(0); w2(0xa);
+ if (pi->mode == 2) {
+ w2(0xc); w0(0x9); w2(0x8); w2(0xc);
+ }
+}
+
+static void fit3_disconnect(struct pi_adapter *pi)
+{
+ w2(0xc); w0(0xa); w2(0x8); w2(0xc);
+ w0(pi->saved_r0);
+ w2(pi->saved_r2);
+}
+
+static void fit3_log_adapter(struct pi_adapter *pi, char *scratch, int verbose)
+{
+ static char * const mode_string[] = { "4-bit", "8-bit", "EPP" };
+
+ dev_info(&pi->dev, "fit3, FIT 3000 adapter at 0x%x, mode %d (%s), delay %d\n",
+ pi->port, pi->mode, mode_string[pi->mode], pi->delay);
+}
+
+static struct pi_protocol fit3 = {
+ .owner = THIS_MODULE,
+ .name = "fit3",
+ .max_mode = 3,
+ .epp_first = 2,
+ .default_delay = 1,
+ .max_units = 1,
+ .write_regr = fit3_write_regr,
+ .read_regr = fit3_read_regr,
+ .write_block = fit3_write_block,
+ .read_block = fit3_read_block,
+ .connect = fit3_connect,
+ .disconnect = fit3_disconnect,
+ .log_adapter = fit3_log_adapter,
+ .sht = { PATA_PARPORT_SHT("pata_parport-fit3") },
+};
+
+MODULE_LICENSE("GPL");
+module_pata_parport_driver(fit3);
Add FIT TD-3000 protocol driver. Signed-off-by: Ondrej Zary <linux@zary.sk> --- drivers/ata/pata_parport/Kconfig | 12 ++ drivers/ata/pata_parport/Makefile | 1 + drivers/ata/pata_parport/fit3.c | 195 ++++++++++++++++++++++++++++++ 3 files changed, 208 insertions(+) create mode 100644 drivers/ata/pata_parport/fit3.c