diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig index a48586bb8edb..64127740a248 100644 --- a/drivers/gpio/Kconfig +++ b/drivers/gpio/Kconfig @@ -1385,6 +1385,18 @@ config GPIO_BD72720 be configured to GPO on the ROHM PMIC. The pin configuration is done on OTP at manufacturing. +config GPIO_BD73800 + tristate "ROHM BD73800 GPIO support" + depends on MFD_ROHM_BD71828 + select GPIO_REGMAP + help + Support for GPIOs on ROHM BD73800 PMIC. There can be up to 4 + GPI or GPO pins available on the PMIC in total. The purpose of + the pins is decided at the device manufacturing by OTP + configuration and can't be reconfigured later. Enable this + if your PMIC has pins set as GPIs or GPOs and if you wish to + control the pins via the GPIO framework. + config GPIO_BD9571MWV tristate "ROHM BD9571 GPIO support" depends on MFD_BD9571MWV diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile index dc9e6d643b5b..dc5e0583e328 100644 --- a/drivers/gpio/Makefile +++ b/drivers/gpio/Makefile @@ -45,6 +45,7 @@ obj-$(CONFIG_GPIO_BCM_XGS_IPROC) += gpio-xgs-iproc.o obj-$(CONFIG_GPIO_BD71815) += gpio-bd71815.o obj-$(CONFIG_GPIO_BD71828) += gpio-bd71828.o obj-$(CONFIG_GPIO_BD72720) += gpio-bd72720.o +obj-$(CONFIG_GPIO_BD73800) += gpio-bd73800.o obj-$(CONFIG_GPIO_BD9571MWV) += gpio-bd9571mwv.o obj-$(CONFIG_GPIO_BLZP1600) += gpio-blzp1600.o obj-$(CONFIG_GPIO_BRCMSTB) += gpio-brcmstb.o diff --git a/drivers/gpio/gpio-bd73800.c b/drivers/gpio/gpio-bd73800.c new file mode 100644 index 000000000000..824901859a61 --- /dev/null +++ b/drivers/gpio/gpio-bd73800.c @@ -0,0 +1,209 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Support to GPIOs on ROHM BD73800 + * Copyright 2024 ROHM Semiconductors. + * Author: Matti Vaittinen + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +#define BD73800_GPIO_MAX_PINS 4 +/* + * The BD73800 has several "one time programmable" (OTP) configurations which + * can be set at manufacturing phase. Some of these options allow using + * individual pins as GPI or GPO (not both at the same time). The OTP + * configuration can't be read at run-time, so drivers rely on device-tree to + * advertise the OTP programmed in manufacturing. + * + * The pins which can be used as GPIO are: + * GPIO1, CLKOUT (GPIO2), FAULT_B, EXTEN_OUT. + * + * The OTP options 2 and 3 state for all the pins: + * - OTP2: GPI (also IRQ source) + * - OTP3: GPO (NOTE: This is actually 2 different OTP options. Either a + * register controllable output or a power-sequence controlled output. + * The "gpo" referred here means only the register controllable output.) + * The datasheet refers to this as: " output is controlled by + * GPIO_OUT or power on/off sequencer to control external VRs. ON/OFF + * sequence timing is configurable." + * + * The data-sheet further says that the GPI/GPO is not a default OTP + * configuration for any of the pins. Hence the GPIO driver defaults to a pin + * not being a GPI or GPO, but requires the pin to be explicitly marked as a + * GPI or GPO in the device-tree. + * + * DT properties: + * "rohm,pin-gpio1", "rohm,pin-clkout", "rohm,pin-fault_b", "rohm,pin-exten" + * can be set to one of the values "gpi" or "gpo" to enable them to be used as + * GPIO. + * + * The amount of GPIO lines the chip exposes to the user-space (chip.ngpio) is + * always the same, regardless of the OTP variant in use. The lines which are + * not usable as GPIO on a given OTP variant are marked invalid via the GPIO + * valid_mask. This way the user-space always sees a constant amount of GPIO + * lines, where numbering (relative to the chip's base) stays also the same. + * Users can then use the valid_mask to find out which of the lines are usable. + */ + +struct bd73800_gpio { + /* dev points to the platform device for devm and prints */ + struct device *dev; + struct regmap *regmap; + /* Pins which have been OTP configured as GPI or GPO */ + DECLARE_BITMAP(valid_mask, BD73800_GPIO_MAX_PINS); + /* Subset of valid_mask - pins which have been OTP configured as GPO */ + DECLARE_BITMAP(output_mask, BD73800_GPIO_MAX_PINS); +}; + +static const char * const bd73800_gpio_properties[BD73800_GPIO_MAX_PINS] = { + "rohm,pin-gpio1", "rohm,pin-clkout", "rohm,pin-fault_b", "rohm,pin-exten" +}; + +static int bd73800_gpio_get_pins(struct bd73800_gpio *data) +{ + struct device *parent = data->dev->parent; + const char *val; + int i, ret; + + for (i = 0; i < BD73800_GPIO_MAX_PINS; i++) { + ret = device_property_read_string(parent, + bd73800_gpio_properties[i], + &val); + if (ret) { + if (ret == -EINVAL) + continue; + + return dev_err_probe(data->dev, ret, + "pin %d (%s), bad configuration\n", i, + bd73800_gpio_properties[i]); + } + + if (!strcmp(val, "gpi")) { + __set_bit(i, data->valid_mask); + } else if (!strcmp(val, "gpo")) { + __set_bit(i, data->valid_mask); + __set_bit(i, data->output_mask); + } else { + dev_warn(data->dev, + "pin %d (%s), unknown value '%s' ignored\n", i, + bd73800_gpio_properties[i], val); + } + } + + return 0; +} + +static int bd73800_gpio_init_valid_mask(struct gpio_chip *gc, + unsigned long *valid_mask, + unsigned int ngpios) +{ + struct gpio_regmap *gpio = gpiochip_get_data(gc); + struct bd73800_gpio *data = gpio_regmap_get_drvdata(gpio); + + bitmap_copy(valid_mask, data->valid_mask, ngpios); + + return 0; +} + +/* + * The used register depends on OTP: + * - If OTP has set pin as GPO, only the GPO_OUT register is valid. + * - If OTP has set pin as GPI, only the INT_5_SRC register is valid. + */ +static int bd73800_gpio_reg_mask_xlate(struct gpio_regmap *gpio, + enum gpio_regmap_operation op, + unsigned int base, unsigned int offset, + unsigned int *reg, unsigned int *mask) +{ + struct bd73800_gpio *data = gpio_regmap_get_drvdata(gpio); + bool is_output = test_bit(offset, data->output_mask); + + if (is_output) + *reg = BD73800_REG_GPO_OUT; + else + *reg = base; + + *mask = BIT(offset); + + return 0; +} + +static int gpo_bd73800_probe(struct platform_device *pdev) +{ + struct gpio_regmap_config config = { }; + struct bd73800_gpio *data; + struct device *parent, *dev; + struct gpio_regmap *gpio; + int ret; + + dev = &pdev->dev; + /* The device-tree and regmap come from MFD => use parent for that */ + parent = dev->parent; + + data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL); + if (!data) + return -ENOMEM; + + data->dev = dev; + data->regmap = dev_get_regmap(parent, NULL); + if (!data->regmap) + return dev_err_probe(dev, -ENODEV, "no parent regmap\n"); + + ret = bd73800_gpio_get_pins(data); + if (ret) + return ret; + + if (bitmap_empty(data->valid_mask, BD73800_GPIO_MAX_PINS)) { + /* + * The BD73800 may or may not have pins allocated for GPIO + * depending on the OTP used at manufacturing. + * If there are no pins, then we have nothing to do. + */ + dev_dbg(dev, "no GPIO pins\n"); + return -ENODEV; + } + + config.parent = parent; + config.regmap = data->regmap; + config.label = "bd73800"; + config.ngpio = BD73800_GPIO_MAX_PINS; + config.reg_dat_base = BD73800_REG_INT_5_SRC; + config.reg_set_base = BD73800_REG_GPO_OUT; + config.reg_mask_xlate = bd73800_gpio_reg_mask_xlate; + config.init_valid_mask = bd73800_gpio_init_valid_mask; + /* All pins that are valid GPIO lines also have a fixed direction */ + config.fixed_direction_mask = data->valid_mask; + config.fixed_direction_output = data->output_mask; + config.drvdata = data; + + gpio = devm_gpio_regmap_register(dev, &config); + + return PTR_ERR_OR_ZERO(gpio); +} + +static const struct platform_device_id bd73800_gpio_id[] = { + { "bd73800-gpio" }, + { }, +}; +MODULE_DEVICE_TABLE(platform, bd73800_gpio_id); + +static struct platform_driver gpo_bd73800_driver = { + .driver = { + .name = "bd73800-gpio", + .probe_type = PROBE_PREFER_ASYNCHRONOUS, + }, + .probe = gpo_bd73800_probe, + .id_table = bd73800_gpio_id, +}; +module_platform_driver(gpo_bd73800_driver); + +MODULE_AUTHOR("Matti Vaittinen "); +MODULE_DESCRIPTION("GPIO interface for BD73800"); +MODULE_LICENSE("GPL");