diff mbox series

[v2,11/11] arm64: dts: renesas: rzg3s-smarc-som: Enable the Ethernet interfaces

Message ID 20231207070700.4156557-12-claudiu.beznea.uj@bp.renesas.com
State New
Headers show
Series renesas: rzg3s: Add support for Ethernet | expand

Commit Message

Claudiu Dec. 7, 2023, 7:07 a.m. UTC
From: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>

The RZ/G3S Smarc Module has Ethernet PHYs (KSZ9131) connected to each
Ethernet IP. For this, add proper DT bindings to enable the Ethernet
communication through these PHYs.

The interface b/w PHYs and MACs is RGMII. The skew settings were set to
zero as based on phy-mode (rgmii-id) the KSZ9131 driver enables internal
DLL, which adds a 2ns delay b/w clocks (TX/RX) and data signals.

Different pin settings were applied to TXC and TX_CTL compared with the
rest of the RGMII pins to comply with requirements for these pins imposed
by HW manual of RZ/G3S (see chapters "Ether Ch0 Voltage Mode Control
Register (ETH0_POC)", "Ether Ch1 Voltage Mode Control Register (ETH1_POC)",
for power source selection, "Ether MII/RGMII Mode Control Register
(ETH_MODE)" for output-enable and "Input Enable Control Register (IEN_m)"
for input-enable configurations).

Commit also enables the Ethernet interfaces by selecting
SW_CONFIG3 = SW_ON.

Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
---

Changes in v2:
- removed #address-cells, #size-cells
- adapted patch description to reflect the usage of SW_CONFIG

 .../boot/dts/renesas/rzg3s-smarc-som.dtsi     | 141 +++++++++++++++++-
 1 file changed, 140 insertions(+), 1 deletion(-)

Comments

Geert Uytterhoeven Dec. 13, 2023, 2:09 p.m. UTC | #1
On Thu, Dec 7, 2023 at 8:08 AM Claudiu <claudiu.beznea@tuxon.dev> wrote:
> From: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
>
> The RZ/G3S Smarc Module has Ethernet PHYs (KSZ9131) connected to each
> Ethernet IP. For this, add proper DT bindings to enable the Ethernet
> communication through these PHYs.
>
> The interface b/w PHYs and MACs is RGMII. The skew settings were set to
> zero as based on phy-mode (rgmii-id) the KSZ9131 driver enables internal
> DLL, which adds a 2ns delay b/w clocks (TX/RX) and data signals.
>
> Different pin settings were applied to TXC and TX_CTL compared with the
> rest of the RGMII pins to comply with requirements for these pins imposed
> by HW manual of RZ/G3S (see chapters "Ether Ch0 Voltage Mode Control
> Register (ETH0_POC)", "Ether Ch1 Voltage Mode Control Register (ETH1_POC)",
> for power source selection, "Ether MII/RGMII Mode Control Register
> (ETH_MODE)" for output-enable and "Input Enable Control Register (IEN_m)"
> for input-enable configurations).
>
> Commit also enables the Ethernet interfaces by selecting
> SW_CONFIG3 = SW_ON.
>
> Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
> ---
>
> Changes in v2:
> - removed #address-cells, #size-cells
> - adapted patch description to reflect the usage of SW_CONFIG

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
i.e. will queue in renesas-devel for v6.8.

Gr{oetje,eeting}s,

                        Geert
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi b/arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi
index f59094701a4a..f062d4ad78b7 100644
--- a/arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi
+++ b/arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi
@@ -26,7 +26,7 @@ 
  *	SW_ON  - SCIF1, SSI0, IRQ0, IRQ1 connected to SoC
  */
 #define SW_CONFIG2	SW_ON
-#define SW_CONFIG3	SW_OFF
+#define SW_CONFIG3	SW_ON
 
 / {
 	compatible = "renesas,rzg3s-smarcm", "renesas,r9a08g045s33", "renesas,r9a08g045";
@@ -35,6 +35,9 @@  aliases {
 		mmc0 = &sdhi0;
 #if SW_CONFIG3 == SW_OFF
 		mmc2 = &sdhi2;
+#else
+		eth0 = &eth0;
+		eth1 = &eth1;
 #endif
 	};
 
@@ -89,6 +92,60 @@  vcc_sdhi2: regulator2 {
 	};
 };
 
+#if SW_CONFIG3 == SW_ON
+&eth0 {
+	pinctrl-0 = <&eth0_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	phy0: ethernet-phy@7 {
+		reg = <7>;
+		interrupt-parent = <&pinctrl>;
+		interrupts = <RZG2L_GPIO(12, 0) IRQ_TYPE_EDGE_FALLING>;
+		rxc-skew-psec = <0>;
+		txc-skew-psec = <0>;
+		rxdv-skew-psec = <0>;
+		txen-skew-psec = <0>;
+		rxd0-skew-psec = <0>;
+		rxd1-skew-psec = <0>;
+		rxd2-skew-psec = <0>;
+		rxd3-skew-psec = <0>;
+		txd0-skew-psec = <0>;
+		txd1-skew-psec = <0>;
+		txd2-skew-psec = <0>;
+		txd3-skew-psec = <0>;
+	};
+};
+
+&eth1 {
+	pinctrl-0 = <&eth1_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	phy1: ethernet-phy@7 {
+		reg = <7>;
+		interrupt-parent = <&pinctrl>;
+		interrupts = <RZG2L_GPIO(12, 1) IRQ_TYPE_EDGE_FALLING>;
+		rxc-skew-psec = <0>;
+		txc-skew-psec = <0>;
+		rxdv-skew-psec = <0>;
+		txen-skew-psec = <0>;
+		rxd0-skew-psec = <0>;
+		rxd1-skew-psec = <0>;
+		rxd2-skew-psec = <0>;
+		rxd3-skew-psec = <0>;
+		txd0-skew-psec = <0>;
+		txd1-skew-psec = <0>;
+		txd2-skew-psec = <0>;
+		txd3-skew-psec = <0>;
+	};
+};
+#endif
+
 &extal_clk {
 	clock-frequency = <24000000>;
 };
@@ -136,6 +193,88 @@  &sdhi2 {
 #endif
 
 &pinctrl {
+	eth0-phy-irq-hog {
+		gpio-hog;
+		gpios = <RZG2L_GPIO(12, 0) GPIO_ACTIVE_LOW>;
+		input;
+		line-name = "eth0-phy-irq";
+	};
+
+	eth0_pins: eth0 {
+		txc {
+			pinmux = <RZG2L_PORT_PINMUX(1, 0, 1)>;  /* ET0_TXC */
+			power-source = <1800>;
+			output-enable;
+			input-enable;
+			drive-strength-microamp = <5200>;
+		};
+
+		tx_ctl {
+			pinmux = <RZG2L_PORT_PINMUX(1, 1, 1)>;  /* ET0_TX_CTL */
+			power-source = <1800>;
+			output-enable;
+			drive-strength-microamp = <5200>;
+		};
+
+		mux {
+			pinmux = <RZG2L_PORT_PINMUX(1, 2, 1)>,	/* ET0_TXD0 */
+				 <RZG2L_PORT_PINMUX(1, 3, 1)>,	/* ET0_TXD1 */
+				 <RZG2L_PORT_PINMUX(1, 4, 1)>,	/* ET0_TXD2 */
+				 <RZG2L_PORT_PINMUX(2, 0, 1)>,	/* ET0_TXD3 */
+				 <RZG2L_PORT_PINMUX(3, 0, 1)>,	/* ET0_RXC */
+				 <RZG2L_PORT_PINMUX(3, 1, 1)>,	/* ET0_RX_CTL */
+				 <RZG2L_PORT_PINMUX(3, 2, 1)>,	/* ET0_RXD0 */
+				 <RZG2L_PORT_PINMUX(3, 3, 1)>,	/* ET0_RXD1 */
+				 <RZG2L_PORT_PINMUX(4, 0, 1)>,	/* ET0_RXD2 */
+				 <RZG2L_PORT_PINMUX(4, 1, 1)>,	/* ET0_RXD3 */
+				 <RZG2L_PORT_PINMUX(4, 3, 1)>,	/* ET0_MDC */
+				 <RZG2L_PORT_PINMUX(4, 4, 1)>,	/* ET0_MDIO */
+				 <RZG2L_PORT_PINMUX(4, 5, 1)>;	/* ET0_LINKSTA */
+			power-source = <1800>;
+		};
+	};
+
+	eth1-phy-irq-hog {
+		gpio-hog;
+		gpios = <RZG2L_GPIO(12, 1) GPIO_ACTIVE_LOW>;
+		input;
+		line-name = "eth1-phy-irq";
+	};
+
+	eth1_pins: eth1 {
+		txc {
+			pinmux = <RZG2L_PORT_PINMUX(7, 0, 1)>;	/* ET1_TXC */
+			power-source = <1800>;
+			output-enable;
+			input-enable;
+			drive-strength-microamp = <5200>;
+		};
+
+		tx_ctl {
+			pinmux = <RZG2L_PORT_PINMUX(7, 1, 1)>;	/* ET1_TX_CTL */
+			power-source = <1800>;
+			output-enable;
+			drive-strength-microamp = <5200>;
+		};
+
+		mux {
+			pinmux = <RZG2L_PORT_PINMUX(7, 2, 1)>,	/* ET1_TXD0 */
+				 <RZG2L_PORT_PINMUX(7, 3, 1)>,	/* ET1_TXD1 */
+				 <RZG2L_PORT_PINMUX(7, 4, 1)>,	/* ET1_TXD2 */
+				 <RZG2L_PORT_PINMUX(8, 0, 1)>,	/* ET1_TXD3 */
+				 <RZG2L_PORT_PINMUX(8, 4, 1)>,	/* ET1_RXC */
+				 <RZG2L_PORT_PINMUX(9, 0, 1)>,	/* ET1_RX_CTL */
+				 <RZG2L_PORT_PINMUX(9, 1, 1)>,	/* ET1_RXD0 */
+				 <RZG2L_PORT_PINMUX(9, 2, 1)>,	/* ET1_RXD1 */
+				 <RZG2L_PORT_PINMUX(9, 3, 1)>,	/* ET1_RXD2 */
+				 <RZG2L_PORT_PINMUX(10, 0, 1)>,	/* ET1_RXD3 */
+				 <RZG2L_PORT_PINMUX(10, 2, 1)>,	/* ET1_MDC */
+				 <RZG2L_PORT_PINMUX(10, 3, 1)>,	/* ET1_MDIO */
+				 <RZG2L_PORT_PINMUX(10, 4, 1)>;	/* ET1_LINKSTA */
+			power-source = <1800>;
+		};
+	};
+
 	sdhi0_pins: sd0 {
 		data {
 			pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3";