| Message ID | 20230616185742.2250452-2-krzysztof.kozlowski@linaro.org |
|---|---|
| State | New |
| Headers | show |
| Series | [1/3] dt-bindings: pinctrl: qcom,sm8350-lpass-lpi: add SM8350 LPASS TLMM | expand |
On 16.06.2023 20:57, Krzysztof Kozlowski wrote: > Add driver for pin controller in Low Power Audio SubSystem (LPASS). The > driver is similar to SM8450 LPASS pin controller, with difference in one > new pin (gpio14). 8250* 8450 has a whole lot more! The 8250 in fact does look almost identical.. Perhaps in this case it would be sane to combine the two? Konrad > > Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> > --- > drivers/pinctrl/qcom/Kconfig | 10 ++ > drivers/pinctrl/qcom/Makefile | 1 + > .../pinctrl/qcom/pinctrl-sm8350-lpass-lpi.c | 167 ++++++++++++++++++ > 3 files changed, 178 insertions(+) > create mode 100644 drivers/pinctrl/qcom/pinctrl-sm8350-lpass-lpi.c > > diff --git a/drivers/pinctrl/qcom/Kconfig b/drivers/pinctrl/qcom/Kconfig > index 634c75336983..9c43bc05c447 100644 > --- a/drivers/pinctrl/qcom/Kconfig > +++ b/drivers/pinctrl/qcom/Kconfig > @@ -77,6 +77,16 @@ config PINCTRL_SM8250_LPASS_LPI > Qualcomm Technologies Inc LPASS (Low Power Audio SubSystem) LPI > (Low Power Island) found on the Qualcomm Technologies Inc SM8250 platform. > > +config PINCTRL_SM3550_LPASS_LPI > + tristate "Qualcomm Technologies Inc SM8350 LPASS LPI pin controller driver" > + depends on ARM64 || COMPILE_TEST > + depends on PINCTRL_LPASS_LPI > + help > + This is the pinctrl, pinmux, pinconf and gpiolib driver for the > + Qualcomm Technologies Inc LPASS (Low Power Audio SubSystem) LPI > + (Low Power Island) found on the Qualcomm Technologies Inc SM8350 > + platform. > + > config PINCTRL_SM8450_LPASS_LPI > tristate "Qualcomm Technologies Inc SM8450 LPASS LPI pin controller driver" > depends on ARM64 || COMPILE_TEST > diff --git a/drivers/pinctrl/qcom/Makefile b/drivers/pinctrl/qcom/Makefile > index 426ddbf35f32..76ffcfbffc8e 100644 > --- a/drivers/pinctrl/qcom/Makefile > +++ b/drivers/pinctrl/qcom/Makefile > @@ -52,6 +52,7 @@ obj-$(CONFIG_PINCTRL_SM8150) += pinctrl-sm8150.o > obj-$(CONFIG_PINCTRL_SM8250) += pinctrl-sm8250.o > obj-$(CONFIG_PINCTRL_SM8250_LPASS_LPI) += pinctrl-sm8250-lpass-lpi.o > obj-$(CONFIG_PINCTRL_SM8350) += pinctrl-sm8350.o > +obj-$(CONFIG_PINCTRL_SM8350_LPASS_LPI) += pinctrl-sm8350-lpass-lpi.o > obj-$(CONFIG_PINCTRL_SM8450) += pinctrl-sm8450.o > obj-$(CONFIG_PINCTRL_SM8450_LPASS_LPI) += pinctrl-sm8450-lpass-lpi.o > obj-$(CONFIG_PINCTRL_SM8550) += pinctrl-sm8550.o > diff --git a/drivers/pinctrl/qcom/pinctrl-sm8350-lpass-lpi.c b/drivers/pinctrl/qcom/pinctrl-sm8350-lpass-lpi.c > new file mode 100644 > index 000000000000..23cce59d1a95 > --- /dev/null > +++ b/drivers/pinctrl/qcom/pinctrl-sm8350-lpass-lpi.c > @@ -0,0 +1,167 @@ > +// SPDX-License-Identifier: GPL-2.0-only > +/* > + * Copyright (c) 2016-2019, The Linux Foundation. All rights reserved. > + * Copyright (c) 20202-2023 Linaro Ltd. > + */ > + > +#include <linux/gpio/driver.h> > +#include <linux/module.h> > +#include <linux/platform_device.h> > + > +#include "pinctrl-lpass-lpi.h" > + > +enum lpass_lpi_functions { > + LPI_MUX_dmic1_clk, > + LPI_MUX_dmic1_data, > + LPI_MUX_dmic2_clk, > + LPI_MUX_dmic2_data, > + LPI_MUX_dmic3_clk, > + LPI_MUX_dmic3_data, > + LPI_MUX_i2s1_clk, > + LPI_MUX_i2s1_data, > + LPI_MUX_i2s1_ws, > + LPI_MUX_i2s2_clk, > + LPI_MUX_i2s2_data, > + LPI_MUX_i2s2_ws, > + LPI_MUX_qua_mi2s_data, > + LPI_MUX_qua_mi2s_sclk, > + LPI_MUX_qua_mi2s_ws, > + LPI_MUX_swr_rx_clk, > + LPI_MUX_swr_rx_data, > + LPI_MUX_swr_tx_clk, > + LPI_MUX_swr_tx_data, > + LPI_MUX_swr_tx_data2, > + LPI_MUX_wsa_swr_clk, > + LPI_MUX_wsa_swr_data, > + LPI_MUX_gpio, > + LPI_MUX__, > +}; > + > +static int gpio0_pins[] = { 0 }; > +static int gpio1_pins[] = { 1 }; > +static int gpio2_pins[] = { 2 }; > +static int gpio3_pins[] = { 3 }; > +static int gpio4_pins[] = { 4 }; > +static int gpio5_pins[] = { 5 }; > +static int gpio6_pins[] = { 6 }; > +static int gpio7_pins[] = { 7 }; > +static int gpio8_pins[] = { 8 }; > +static int gpio9_pins[] = { 9 }; > +static int gpio10_pins[] = { 10 }; > +static int gpio11_pins[] = { 11 }; > +static int gpio12_pins[] = { 12 }; > +static int gpio13_pins[] = { 13 }; > +static int gpio14_pins[] = { 14 }; > + > +static const struct pinctrl_pin_desc sm8350_lpi_pins[] = { > + PINCTRL_PIN(0, "gpio0"), > + PINCTRL_PIN(1, "gpio1"), > + PINCTRL_PIN(2, "gpio2"), > + PINCTRL_PIN(3, "gpio3"), > + PINCTRL_PIN(4, "gpio4"), > + PINCTRL_PIN(5, "gpio5"), > + PINCTRL_PIN(6, "gpio6"), > + PINCTRL_PIN(7, "gpio7"), > + PINCTRL_PIN(8, "gpio8"), > + PINCTRL_PIN(9, "gpio9"), > + PINCTRL_PIN(10, "gpio10"), > + PINCTRL_PIN(11, "gpio11"), > + PINCTRL_PIN(12, "gpio12"), > + PINCTRL_PIN(13, "gpio13"), > + PINCTRL_PIN(14, "gpio14"), > +}; > + > +static const char * const swr_tx_clk_groups[] = { "gpio0" }; > +static const char * const swr_tx_data_groups[] = { "gpio1", "gpio2", "gpio5", "gpio14" }; > +static const char * const swr_rx_clk_groups[] = { "gpio3" }; > +static const char * const swr_rx_data_groups[] = { "gpio4", "gpio5" }; > +static const char * const dmic1_clk_groups[] = { "gpio6" }; > +static const char * const dmic1_data_groups[] = { "gpio7" }; > +static const char * const dmic2_clk_groups[] = { "gpio8" }; > +static const char * const dmic2_data_groups[] = { "gpio9" }; > +static const char * const i2s2_clk_groups[] = { "gpio10" }; > +static const char * const i2s2_ws_groups[] = { "gpio11" }; > +static const char * const dmic3_clk_groups[] = { "gpio12" }; > +static const char * const dmic3_data_groups[] = { "gpio13" }; > +static const char * const qua_mi2s_sclk_groups[] = { "gpio0" }; > +static const char * const qua_mi2s_ws_groups[] = { "gpio1" }; > +static const char * const qua_mi2s_data_groups[] = { "gpio2", "gpio3", "gpio4" }; > +static const char * const i2s1_clk_groups[] = { "gpio6" }; > +static const char * const i2s1_ws_groups[] = { "gpio7" }; > +static const char * const i2s1_data_groups[] = { "gpio8", "gpio9" }; > +static const char * const wsa_swr_clk_groups[] = { "gpio10" }; > +static const char * const wsa_swr_data_groups[] = { "gpio11" }; > +static const char * const i2s2_data_groups[] = { "gpio12", "gpio12" }; > + > +static const struct lpi_pingroup sm8350_groups[] = { > + LPI_PINGROUP(0, 0, swr_tx_clk, qua_mi2s_sclk, _, _), > + LPI_PINGROUP(1, 2, swr_tx_data, qua_mi2s_ws, _, _), > + LPI_PINGROUP(2, 4, swr_tx_data, qua_mi2s_data, _, _), > + LPI_PINGROUP(3, 8, swr_rx_clk, qua_mi2s_data, _, _), > + LPI_PINGROUP(4, 10, swr_rx_data, qua_mi2s_data, _, _), > + LPI_PINGROUP(5, 12, swr_tx_data, swr_rx_data, _, _), > + LPI_PINGROUP(6, LPI_NO_SLEW, dmic1_clk, i2s1_clk, _, _), > + LPI_PINGROUP(7, LPI_NO_SLEW, dmic1_data, i2s1_ws, _, _), > + LPI_PINGROUP(8, LPI_NO_SLEW, dmic2_clk, i2s1_data, _, _), > + LPI_PINGROUP(9, LPI_NO_SLEW, dmic2_data, i2s1_data, _, _), > + LPI_PINGROUP(10, 16, i2s2_clk, wsa_swr_clk, _, _), > + LPI_PINGROUP(11, 18, i2s2_ws, wsa_swr_data, _, _), > + LPI_PINGROUP(12, LPI_NO_SLEW, dmic3_clk, i2s2_data, _, _), > + LPI_PINGROUP(13, LPI_NO_SLEW, dmic3_data, i2s2_data, _, _), > + LPI_PINGROUP(14, 6, swr_rx_data, _, _, _), > +}; > + > +static const struct lpi_function sm8350_functions[] = { > + LPI_FUNCTION(dmic1_clk), > + LPI_FUNCTION(dmic1_data), > + LPI_FUNCTION(dmic2_clk), > + LPI_FUNCTION(dmic2_data), > + LPI_FUNCTION(dmic3_clk), > + LPI_FUNCTION(dmic3_data), > + LPI_FUNCTION(i2s1_clk), > + LPI_FUNCTION(i2s1_data), > + LPI_FUNCTION(i2s1_ws), > + LPI_FUNCTION(i2s2_clk), > + LPI_FUNCTION(i2s2_data), > + LPI_FUNCTION(i2s2_ws), > + LPI_FUNCTION(qua_mi2s_data), > + LPI_FUNCTION(qua_mi2s_sclk), > + LPI_FUNCTION(qua_mi2s_ws), > + LPI_FUNCTION(swr_rx_clk), > + LPI_FUNCTION(swr_rx_data), > + LPI_FUNCTION(swr_tx_clk), > + LPI_FUNCTION(swr_tx_data), > + LPI_FUNCTION(wsa_swr_clk), > + LPI_FUNCTION(wsa_swr_data), > +}; > + > +static const struct lpi_pinctrl_variant_data sm8350_lpi_data = { > + .pins = sm8350_lpi_pins, > + .npins = ARRAY_SIZE(sm8350_lpi_pins), > + .groups = sm8350_groups, > + .ngroups = ARRAY_SIZE(sm8350_groups), > + .functions = sm8350_functions, > + .nfunctions = ARRAY_SIZE(sm8350_functions), > +}; > + > +static const struct of_device_id lpi_pinctrl_of_match[] = { > + { > + .compatible = "qcom,sm8350-lpass-lpi-pinctrl", > + .data = &sm8350_lpi_data, > + }, > + { } > +}; > +MODULE_DEVICE_TABLE(of, lpi_pinctrl_of_match); > + > +static struct platform_driver lpi_pinctrl_driver = { > + .driver = { > + .name = "qcom-sm8350-lpass-lpi-pinctrl", > + .of_match_table = lpi_pinctrl_of_match, > + }, > + .probe = lpi_pinctrl_probe, > + .remove = lpi_pinctrl_remove, > +}; > + > +module_platform_driver(lpi_pinctrl_driver); > +MODULE_DESCRIPTION("QTI SM8350 LPI GPIO pin control driver"); > +MODULE_LICENSE("GPL");
On 17/06/2023 01:36, Konrad Dybcio wrote: > On 16.06.2023 20:57, Krzysztof Kozlowski wrote: >> Add driver for pin controller in Low Power Audio SubSystem (LPASS). The >> driver is similar to SM8450 LPASS pin controller, with difference in one >> new pin (gpio14). > 8250* > > 8450 has a whole lot more! > > The 8250 in fact does look almost identical.. Perhaps in this case it > would be sane to combine the two? It meant to be 8250 as I copied that one. I'll fix it. Best regards, Krzysztof
On 16/06/2023 20:57, Krzysztof Kozlowski wrote: > Add driver for pin controller in Low Power Audio SubSystem (LPASS). The > driver is similar to SM8450 LPASS pin controller, with difference in one > new pin (gpio14). > > Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> > --- > drivers/pinctrl/qcom/Kconfig | 10 ++ > drivers/pinctrl/qcom/Makefile | 1 + > .../pinctrl/qcom/pinctrl-sm8350-lpass-lpi.c | 167 ++++++++++++++++++ > 3 files changed, 178 insertions(+) > create mode 100644 drivers/pinctrl/qcom/pinctrl-sm8350-lpass-lpi.c > > diff --git a/drivers/pinctrl/qcom/Kconfig b/drivers/pinctrl/qcom/Kconfig > index 634c75336983..9c43bc05c447 100644 > --- a/drivers/pinctrl/qcom/Kconfig > +++ b/drivers/pinctrl/qcom/Kconfig > @@ -77,6 +77,16 @@ config PINCTRL_SM8250_LPASS_LPI > Qualcomm Technologies Inc LPASS (Low Power Audio SubSystem) LPI > (Low Power Island) found on the Qualcomm Technologies Inc SM8250 platform. > > +config PINCTRL_SM3550_LPASS_LPI s/PINCTRL_SM3550_LPASS_LPI/PINCTRL_SM8350_LPASS_LPI/g <snip>
On 19/06/2023 10:55, Neil Armstrong wrote: > On 16/06/2023 20:57, Krzysztof Kozlowski wrote: >> Add driver for pin controller in Low Power Audio SubSystem (LPASS). The >> driver is similar to SM8450 LPASS pin controller, with difference in one >> new pin (gpio14). >> >> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> >> --- >> drivers/pinctrl/qcom/Kconfig | 10 ++ >> drivers/pinctrl/qcom/Makefile | 1 + >> .../pinctrl/qcom/pinctrl-sm8350-lpass-lpi.c | 167 ++++++++++++++++++ >> 3 files changed, 178 insertions(+) >> create mode 100644 drivers/pinctrl/qcom/pinctrl-sm8350-lpass-lpi.c >> >> diff --git a/drivers/pinctrl/qcom/Kconfig b/drivers/pinctrl/qcom/Kconfig >> index 634c75336983..9c43bc05c447 100644 >> --- a/drivers/pinctrl/qcom/Kconfig >> +++ b/drivers/pinctrl/qcom/Kconfig >> @@ -77,6 +77,16 @@ config PINCTRL_SM8250_LPASS_LPI >> Qualcomm Technologies Inc LPASS (Low Power Audio SubSystem) LPI >> (Low Power Island) found on the Qualcomm Technologies Inc SM8250 platform. >> >> +config PINCTRL_SM3550_LPASS_LPI > > s/PINCTRL_SM3550_LPASS_LPI/PINCTRL_SM8350_LPASS_LPI/g Indeed, thanks. Best regards, Krzysztof
diff --git a/drivers/pinctrl/qcom/Kconfig b/drivers/pinctrl/qcom/Kconfig index 634c75336983..9c43bc05c447 100644 --- a/drivers/pinctrl/qcom/Kconfig +++ b/drivers/pinctrl/qcom/Kconfig @@ -77,6 +77,16 @@ config PINCTRL_SM8250_LPASS_LPI Qualcomm Technologies Inc LPASS (Low Power Audio SubSystem) LPI (Low Power Island) found on the Qualcomm Technologies Inc SM8250 platform. +config PINCTRL_SM3550_LPASS_LPI + tristate "Qualcomm Technologies Inc SM8350 LPASS LPI pin controller driver" + depends on ARM64 || COMPILE_TEST + depends on PINCTRL_LPASS_LPI + help + This is the pinctrl, pinmux, pinconf and gpiolib driver for the + Qualcomm Technologies Inc LPASS (Low Power Audio SubSystem) LPI + (Low Power Island) found on the Qualcomm Technologies Inc SM8350 + platform. + config PINCTRL_SM8450_LPASS_LPI tristate "Qualcomm Technologies Inc SM8450 LPASS LPI pin controller driver" depends on ARM64 || COMPILE_TEST diff --git a/drivers/pinctrl/qcom/Makefile b/drivers/pinctrl/qcom/Makefile index 426ddbf35f32..76ffcfbffc8e 100644 --- a/drivers/pinctrl/qcom/Makefile +++ b/drivers/pinctrl/qcom/Makefile @@ -52,6 +52,7 @@ obj-$(CONFIG_PINCTRL_SM8150) += pinctrl-sm8150.o obj-$(CONFIG_PINCTRL_SM8250) += pinctrl-sm8250.o obj-$(CONFIG_PINCTRL_SM8250_LPASS_LPI) += pinctrl-sm8250-lpass-lpi.o obj-$(CONFIG_PINCTRL_SM8350) += pinctrl-sm8350.o +obj-$(CONFIG_PINCTRL_SM8350_LPASS_LPI) += pinctrl-sm8350-lpass-lpi.o obj-$(CONFIG_PINCTRL_SM8450) += pinctrl-sm8450.o obj-$(CONFIG_PINCTRL_SM8450_LPASS_LPI) += pinctrl-sm8450-lpass-lpi.o obj-$(CONFIG_PINCTRL_SM8550) += pinctrl-sm8550.o diff --git a/drivers/pinctrl/qcom/pinctrl-sm8350-lpass-lpi.c b/drivers/pinctrl/qcom/pinctrl-sm8350-lpass-lpi.c new file mode 100644 index 000000000000..23cce59d1a95 --- /dev/null +++ b/drivers/pinctrl/qcom/pinctrl-sm8350-lpass-lpi.c @@ -0,0 +1,167 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (c) 2016-2019, The Linux Foundation. All rights reserved. + * Copyright (c) 20202-2023 Linaro Ltd. + */ + +#include <linux/gpio/driver.h> +#include <linux/module.h> +#include <linux/platform_device.h> + +#include "pinctrl-lpass-lpi.h" + +enum lpass_lpi_functions { + LPI_MUX_dmic1_clk, + LPI_MUX_dmic1_data, + LPI_MUX_dmic2_clk, + LPI_MUX_dmic2_data, + LPI_MUX_dmic3_clk, + LPI_MUX_dmic3_data, + LPI_MUX_i2s1_clk, + LPI_MUX_i2s1_data, + LPI_MUX_i2s1_ws, + LPI_MUX_i2s2_clk, + LPI_MUX_i2s2_data, + LPI_MUX_i2s2_ws, + LPI_MUX_qua_mi2s_data, + LPI_MUX_qua_mi2s_sclk, + LPI_MUX_qua_mi2s_ws, + LPI_MUX_swr_rx_clk, + LPI_MUX_swr_rx_data, + LPI_MUX_swr_tx_clk, + LPI_MUX_swr_tx_data, + LPI_MUX_swr_tx_data2, + LPI_MUX_wsa_swr_clk, + LPI_MUX_wsa_swr_data, + LPI_MUX_gpio, + LPI_MUX__, +}; + +static int gpio0_pins[] = { 0 }; +static int gpio1_pins[] = { 1 }; +static int gpio2_pins[] = { 2 }; +static int gpio3_pins[] = { 3 }; +static int gpio4_pins[] = { 4 }; +static int gpio5_pins[] = { 5 }; +static int gpio6_pins[] = { 6 }; +static int gpio7_pins[] = { 7 }; +static int gpio8_pins[] = { 8 }; +static int gpio9_pins[] = { 9 }; +static int gpio10_pins[] = { 10 }; +static int gpio11_pins[] = { 11 }; +static int gpio12_pins[] = { 12 }; +static int gpio13_pins[] = { 13 }; +static int gpio14_pins[] = { 14 }; + +static const struct pinctrl_pin_desc sm8350_lpi_pins[] = { + PINCTRL_PIN(0, "gpio0"), + PINCTRL_PIN(1, "gpio1"), + PINCTRL_PIN(2, "gpio2"), + PINCTRL_PIN(3, "gpio3"), + PINCTRL_PIN(4, "gpio4"), + PINCTRL_PIN(5, "gpio5"), + PINCTRL_PIN(6, "gpio6"), + PINCTRL_PIN(7, "gpio7"), + PINCTRL_PIN(8, "gpio8"), + PINCTRL_PIN(9, "gpio9"), + PINCTRL_PIN(10, "gpio10"), + PINCTRL_PIN(11, "gpio11"), + PINCTRL_PIN(12, "gpio12"), + PINCTRL_PIN(13, "gpio13"), + PINCTRL_PIN(14, "gpio14"), +}; + +static const char * const swr_tx_clk_groups[] = { "gpio0" }; +static const char * const swr_tx_data_groups[] = { "gpio1", "gpio2", "gpio5", "gpio14" }; +static const char * const swr_rx_clk_groups[] = { "gpio3" }; +static const char * const swr_rx_data_groups[] = { "gpio4", "gpio5" }; +static const char * const dmic1_clk_groups[] = { "gpio6" }; +static const char * const dmic1_data_groups[] = { "gpio7" }; +static const char * const dmic2_clk_groups[] = { "gpio8" }; +static const char * const dmic2_data_groups[] = { "gpio9" }; +static const char * const i2s2_clk_groups[] = { "gpio10" }; +static const char * const i2s2_ws_groups[] = { "gpio11" }; +static const char * const dmic3_clk_groups[] = { "gpio12" }; +static const char * const dmic3_data_groups[] = { "gpio13" }; +static const char * const qua_mi2s_sclk_groups[] = { "gpio0" }; +static const char * const qua_mi2s_ws_groups[] = { "gpio1" }; +static const char * const qua_mi2s_data_groups[] = { "gpio2", "gpio3", "gpio4" }; +static const char * const i2s1_clk_groups[] = { "gpio6" }; +static const char * const i2s1_ws_groups[] = { "gpio7" }; +static const char * const i2s1_data_groups[] = { "gpio8", "gpio9" }; +static const char * const wsa_swr_clk_groups[] = { "gpio10" }; +static const char * const wsa_swr_data_groups[] = { "gpio11" }; +static const char * const i2s2_data_groups[] = { "gpio12", "gpio12" }; + +static const struct lpi_pingroup sm8350_groups[] = { + LPI_PINGROUP(0, 0, swr_tx_clk, qua_mi2s_sclk, _, _), + LPI_PINGROUP(1, 2, swr_tx_data, qua_mi2s_ws, _, _), + LPI_PINGROUP(2, 4, swr_tx_data, qua_mi2s_data, _, _), + LPI_PINGROUP(3, 8, swr_rx_clk, qua_mi2s_data, _, _), + LPI_PINGROUP(4, 10, swr_rx_data, qua_mi2s_data, _, _), + LPI_PINGROUP(5, 12, swr_tx_data, swr_rx_data, _, _), + LPI_PINGROUP(6, LPI_NO_SLEW, dmic1_clk, i2s1_clk, _, _), + LPI_PINGROUP(7, LPI_NO_SLEW, dmic1_data, i2s1_ws, _, _), + LPI_PINGROUP(8, LPI_NO_SLEW, dmic2_clk, i2s1_data, _, _), + LPI_PINGROUP(9, LPI_NO_SLEW, dmic2_data, i2s1_data, _, _), + LPI_PINGROUP(10, 16, i2s2_clk, wsa_swr_clk, _, _), + LPI_PINGROUP(11, 18, i2s2_ws, wsa_swr_data, _, _), + LPI_PINGROUP(12, LPI_NO_SLEW, dmic3_clk, i2s2_data, _, _), + LPI_PINGROUP(13, LPI_NO_SLEW, dmic3_data, i2s2_data, _, _), + LPI_PINGROUP(14, 6, swr_rx_data, _, _, _), +}; + +static const struct lpi_function sm8350_functions[] = { + LPI_FUNCTION(dmic1_clk), + LPI_FUNCTION(dmic1_data), + LPI_FUNCTION(dmic2_clk), + LPI_FUNCTION(dmic2_data), + LPI_FUNCTION(dmic3_clk), + LPI_FUNCTION(dmic3_data), + LPI_FUNCTION(i2s1_clk), + LPI_FUNCTION(i2s1_data), + LPI_FUNCTION(i2s1_ws), + LPI_FUNCTION(i2s2_clk), + LPI_FUNCTION(i2s2_data), + LPI_FUNCTION(i2s2_ws), + LPI_FUNCTION(qua_mi2s_data), + LPI_FUNCTION(qua_mi2s_sclk), + LPI_FUNCTION(qua_mi2s_ws), + LPI_FUNCTION(swr_rx_clk), + LPI_FUNCTION(swr_rx_data), + LPI_FUNCTION(swr_tx_clk), + LPI_FUNCTION(swr_tx_data), + LPI_FUNCTION(wsa_swr_clk), + LPI_FUNCTION(wsa_swr_data), +}; + +static const struct lpi_pinctrl_variant_data sm8350_lpi_data = { + .pins = sm8350_lpi_pins, + .npins = ARRAY_SIZE(sm8350_lpi_pins), + .groups = sm8350_groups, + .ngroups = ARRAY_SIZE(sm8350_groups), + .functions = sm8350_functions, + .nfunctions = ARRAY_SIZE(sm8350_functions), +}; + +static const struct of_device_id lpi_pinctrl_of_match[] = { + { + .compatible = "qcom,sm8350-lpass-lpi-pinctrl", + .data = &sm8350_lpi_data, + }, + { } +}; +MODULE_DEVICE_TABLE(of, lpi_pinctrl_of_match); + +static struct platform_driver lpi_pinctrl_driver = { + .driver = { + .name = "qcom-sm8350-lpass-lpi-pinctrl", + .of_match_table = lpi_pinctrl_of_match, + }, + .probe = lpi_pinctrl_probe, + .remove = lpi_pinctrl_remove, +}; + +module_platform_driver(lpi_pinctrl_driver); +MODULE_DESCRIPTION("QTI SM8350 LPI GPIO pin control driver"); +MODULE_LICENSE("GPL");
Add driver for pin controller in Low Power Audio SubSystem (LPASS). The driver is similar to SM8450 LPASS pin controller, with difference in one new pin (gpio14). Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> --- drivers/pinctrl/qcom/Kconfig | 10 ++ drivers/pinctrl/qcom/Makefile | 1 + .../pinctrl/qcom/pinctrl-sm8350-lpass-lpi.c | 167 ++++++++++++++++++ 3 files changed, 178 insertions(+) create mode 100644 drivers/pinctrl/qcom/pinctrl-sm8350-lpass-lpi.c