| Message ID | 20230130114702.20606-9-quic_kathirav@quicinc.com |
|---|---|
| State | New |
| Headers | show |
| Series | Add minimal boot support for IPQ5332 | expand |
On 30.01.2023 12:47, Kathiravan Thirumoorthy wrote: > From: Kathiravan T <quic_kathirav@quicinc.com> > > Add initial device tree support for the Qualcomm IPQ5332 SoC and > MI01.2 board. > > Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com> > --- [...] > + > + reserved-memory { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + tz_mem: tz@4a600000 { > + no-map; > + reg = <0x0 0x4a600000 0x0 0x200000>; reg should come before no-map > + }; > + }; > + > + soc@0 { > + compatible = "simple-bus"; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges = <0 0 0 0xffffffff>; > + > + tlmm: pinctrl@1000000 { > + compatible = "qcom,ipq5332-tlmm"; > + reg = <0x01000000 0x300000>; > + interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&tlmm 0 0 53>; > + interrupt-controller; > + #interrupt-cells = <2>; > + > + serial_0_pins: serial0-state { > + pins = "gpio18", "gpio19"; > + function = "blsp0_uart0"; > + drive-strength = <8>; > + bias-pull-up; > + }; > + }; > + > + gcc: clock-controller@1800000 { > + compatible = "qcom,ipq5332-gcc"; > + reg = <0x01800000 0x80000>; > + #clock-cells = <1>; > + #reset-cells = <1>; > + #power-domain-cells = <1>; > + clock-names = "xo", > + "sleep_clk", > + "pcie_2lane_phy_pipe_clk", > + "pcie_2lane_phy_pipe_clk_x1", > + "usb_pcie_wrapper_pipe_clk"; > + clocks = <&xo_board>, > + <&sleep_clk>, > + <0>, > + <0>, > + <0>; > + }; > + > + sdhc: mmc@7804000 { > + compatible = "qcom,ipq5332-sdhci", "qcom,sdhci-msm-v5"; > + reg = <0x07804000 0x1000>, <0x07805000 0x1000>; > + > + interrupts = <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "hc_irq", "pwr_irq"; > + > + clocks = <&gcc GCC_SDCC1_AHB_CLK>, > + <&gcc GCC_SDCC1_APPS_CLK>, > + <&xo_board>; > + clock-names = "iface", "core", "xo"; > + mmc-ddr-1_8v; > + mmc-hs200-1_8v; > + max-frequency = <192000000>; > + bus-width = <4>; > + status = "disabled"; > + }; > + > + blsp1_uart0: serial@78af000 { > + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; > + reg = <0x078af000 0x200>; > + interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, > + <&gcc GCC_BLSP1_AHB_CLK>; > + clock-names = "core", "iface"; > + status = "disabled"; > + }; > + > + intc: interrupt-controller@b000000 { > + compatible = "qcom,msm-qgic2"; > + reg = <0x0b000000 0x1000>, /* GICD */ > + <0x0b002000 0x1000>, /* GICC */ > + <0x0b001000 0x1000>, /* GICH */ > + <0x0b004000 0x1000>; /* GICV */ > + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-controller; > + #interrupt-cells = <3>; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges = <0 0x0b00c000 0x3000>; > + > + v2m0: v2m@0 { > + compatible = "arm,gic-v2m-frame"; > + reg = <0x00000000 0xffd>; > + msi-controller; > + }; > + > + v2m1: v2m@1 { > + compatible = "arm,gic-v2m-frame"; > + reg = <0x00001000 0xffd>; The unit address does not match the address part of the reg property, dtbs_check will not succeed.. The rest lgtm Konrad > + msi-controller; > + }; > + > + v2m2: v2m@2 { > + compatible = "arm,gic-v2m-frame"; > + reg = <0x00002000 0xffd>; > + msi-controller; > + }; > + }; > + > + timer@b120000 { > + compatible = "arm,armv7-timer-mem"; > + reg = <0x0b120000 0x1000>; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; > + > + frame@b120000 { > + reg = <0x0b121000 0x1000>, > + <0x0b122000 0x1000>; > + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; > + frame-number = <0>; > + }; > + > + frame@b123000 { > + reg = <0x0b123000 0x1000>; > + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; > + frame-number = <1>; > + status = "disabled"; > + }; > + > + frame@b124000 { > + reg = <0x0b124000 0x1000>; > + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; > + frame-number = <2>; > + status = "disabled"; > + }; > + > + frame@b125000 { > + reg = <0x0b125000 0x1000>; > + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; > + frame-number = <3>; > + status = "disabled"; > + }; > + > + frame@b126000 { > + reg = <0x0b126000 0x1000>; > + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; > + frame-number = <4>; > + status = "disabled"; > + }; > + > + frame@b127000 { > + reg = <0x0b127000 0x1000>; > + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; > + frame-number = <5>; > + status = "disabled"; > + }; > + > + frame@b128000 { > + reg = <0x0b128000 0x1000>; > + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; > + frame-number = <6>; > + status = "disabled"; > + }; > + }; > + }; > + > + timer { > + compatible = "arm,armv8-timer"; > + interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, > + <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, > + <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, > + <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; > + }; > +};
On 30/01/2023 12:47, Kathiravan Thirumoorthy wrote: > From: Kathiravan T <quic_kathirav@quicinc.com> > > Add initial device tree support for the Qualcomm IPQ5332 SoC and > MI01.2 board. > > Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com> > + sdhc: mmc@7804000 { > + compatible = "qcom,ipq5332-sdhci", "qcom,sdhci-msm-v5"; > + reg = <0x07804000 0x1000>, <0x07805000 0x1000>; > + > + interrupts = <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "hc_irq", "pwr_irq"; > + > + clocks = <&gcc GCC_SDCC1_AHB_CLK>, > + <&gcc GCC_SDCC1_APPS_CLK>, > + <&xo_board>; > + clock-names = "iface", "core", "xo"; > + mmc-ddr-1_8v; > + mmc-hs200-1_8v; No, our discussion did not finish. These are not properties of the SoC in most cases. Why do you say there are part of the SoC? Is your SoC coming with the same memory? Memory embedded in the SoC, not in the board? If yes, the status is incorrect. > + max-frequency = <192000000>; Same Best regards, Krzysztof
On 1/30/2023 5:55 PM, Konrad Dybcio wrote: > > On 30.01.2023 12:47, Kathiravan Thirumoorthy wrote: >> From: Kathiravan T <quic_kathirav@quicinc.com> >> >> Add initial device tree support for the Qualcomm IPQ5332 SoC and >> MI01.2 board. >> >> Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com> >> --- > [...] > >> + >> + reserved-memory { >> + #address-cells = <2>; >> + #size-cells = <2>; >> + ranges; >> + >> + tz_mem: tz@4a600000 { >> + no-map; >> + reg = <0x0 0x4a600000 0x0 0x200000>; > reg should come before no-map Ack. Will fix it in V3. > > >> + }; >> + }; >> + >> + soc@0 { >> + compatible = "simple-bus"; >> + #address-cells = <1>; >> + #size-cells = <1>; >> + ranges = <0 0 0 0xffffffff>; >> + >> + tlmm: pinctrl@1000000 { >> + compatible = "qcom,ipq5332-tlmm"; >> + reg = <0x01000000 0x300000>; >> + interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>; >> + gpio-controller; >> + #gpio-cells = <2>; >> + gpio-ranges = <&tlmm 0 0 53>; >> + interrupt-controller; >> + #interrupt-cells = <2>; >> + >> + serial_0_pins: serial0-state { >> + pins = "gpio18", "gpio19"; >> + function = "blsp0_uart0"; >> + drive-strength = <8>; >> + bias-pull-up; >> + }; >> + }; >> + >> + gcc: clock-controller@1800000 { >> + compatible = "qcom,ipq5332-gcc"; >> + reg = <0x01800000 0x80000>; >> + #clock-cells = <1>; >> + #reset-cells = <1>; >> + #power-domain-cells = <1>; >> + clock-names = "xo", >> + "sleep_clk", >> + "pcie_2lane_phy_pipe_clk", >> + "pcie_2lane_phy_pipe_clk_x1", >> + "usb_pcie_wrapper_pipe_clk"; >> + clocks = <&xo_board>, >> + <&sleep_clk>, >> + <0>, >> + <0>, >> + <0>; >> + }; >> + >> + sdhc: mmc@7804000 { >> + compatible = "qcom,ipq5332-sdhci", "qcom,sdhci-msm-v5"; >> + reg = <0x07804000 0x1000>, <0x07805000 0x1000>; >> + >> + interrupts = <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>, >> + <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>; >> + interrupt-names = "hc_irq", "pwr_irq"; >> + >> + clocks = <&gcc GCC_SDCC1_AHB_CLK>, >> + <&gcc GCC_SDCC1_APPS_CLK>, >> + <&xo_board>; >> + clock-names = "iface", "core", "xo"; >> + mmc-ddr-1_8v; >> + mmc-hs200-1_8v; >> + max-frequency = <192000000>; >> + bus-width = <4>; >> + status = "disabled"; >> + }; >> + >> + blsp1_uart0: serial@78af000 { >> + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; >> + reg = <0x078af000 0x200>; >> + interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>; >> + clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, >> + <&gcc GCC_BLSP1_AHB_CLK>; >> + clock-names = "core", "iface"; >> + status = "disabled"; >> + }; >> + >> + intc: interrupt-controller@b000000 { >> + compatible = "qcom,msm-qgic2"; >> + reg = <0x0b000000 0x1000>, /* GICD */ >> + <0x0b002000 0x1000>, /* GICC */ >> + <0x0b001000 0x1000>, /* GICH */ >> + <0x0b004000 0x1000>; /* GICV */ >> + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; >> + interrupt-controller; >> + #interrupt-cells = <3>; >> + #address-cells = <1>; >> + #size-cells = <1>; >> + ranges = <0 0x0b00c000 0x3000>; >> + >> + v2m0: v2m@0 { >> + compatible = "arm,gic-v2m-frame"; >> + reg = <0x00000000 0xffd>; >> + msi-controller; >> + }; >> + >> + v2m1: v2m@1 { >> + compatible = "arm,gic-v2m-frame"; >> + reg = <0x00001000 0xffd>; > The unit address does not match the address part of the reg > property, dtbs_check will not succeed.. Thanks, will update the node name accordingly in V3. AFAIR, I didn't see any dtbs_check warning. Let me cross check it again. > > The rest lgtm Thanks a lot for the review! > > Konrad >> + msi-controller; >> + }; >> + >> + v2m2: v2m@2 { >> + compatible = "arm,gic-v2m-frame"; >> + reg = <0x00002000 0xffd>; >> + msi-controller; >> + }; >> + }; >> + >> + timer@b120000 { >> + compatible = "arm,armv7-timer-mem"; >> + reg = <0x0b120000 0x1000>; >> + #address-cells = <1>; >> + #size-cells = <1>; >> + ranges; >> + >> + frame@b120000 { >> + reg = <0x0b121000 0x1000>, >> + <0x0b122000 0x1000>; >> + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, >> + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; >> + frame-number = <0>; >> + }; >> + >> + frame@b123000 { >> + reg = <0x0b123000 0x1000>; >> + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; >> + frame-number = <1>; >> + status = "disabled"; >> + }; >> + >> + frame@b124000 { >> + reg = <0x0b124000 0x1000>; >> + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; >> + frame-number = <2>; >> + status = "disabled"; >> + }; >> + >> + frame@b125000 { >> + reg = <0x0b125000 0x1000>; >> + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; >> + frame-number = <3>; >> + status = "disabled"; >> + }; >> + >> + frame@b126000 { >> + reg = <0x0b126000 0x1000>; >> + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; >> + frame-number = <4>; >> + status = "disabled"; >> + }; >> + >> + frame@b127000 { >> + reg = <0x0b127000 0x1000>; >> + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; >> + frame-number = <5>; >> + status = "disabled"; >> + }; >> + >> + frame@b128000 { >> + reg = <0x0b128000 0x1000>; >> + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; >> + frame-number = <6>; >> + status = "disabled"; >> + }; >> + }; >> + }; >> + >> + timer { >> + compatible = "arm,armv8-timer"; >> + interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, >> + <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, >> + <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, >> + <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; >> + }; >> +};
On 2/1/2023 12:56 AM, Krzysztof Kozlowski wrote: > On 30/01/2023 12:47, Kathiravan Thirumoorthy wrote: >> From: Kathiravan T <quic_kathirav@quicinc.com> >> >> Add initial device tree support for the Qualcomm IPQ5332 SoC and >> MI01.2 board. >> >> Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com> > >> + sdhc: mmc@7804000 { >> + compatible = "qcom,ipq5332-sdhci", "qcom,sdhci-msm-v5"; >> + reg = <0x07804000 0x1000>, <0x07805000 0x1000>; >> + >> + interrupts = <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>, >> + <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>; >> + interrupt-names = "hc_irq", "pwr_irq"; >> + >> + clocks = <&gcc GCC_SDCC1_AHB_CLK>, >> + <&gcc GCC_SDCC1_APPS_CLK>, >> + <&xo_board>; >> + clock-names = "iface", "core", "xo"; >> + mmc-ddr-1_8v; >> + mmc-hs200-1_8v; > No, our discussion did not finish. These are not properties of the SoC > in most cases. Why do you say there are part of the SoC? Is your SoC > coming with the same memory? Memory embedded in the SoC, not in the > board? If yes, the status is incorrect. Thanks. Got your point, will move the below properties to the board DTS in V3. mmc-ddr-1_8v; mmc-hs200-1_8v; max-frequency = <192000000>; bus-width = <4>; > >> + max-frequency = <192000000>; > Same > > > Best regards, > Krzysztof >
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index b0423ca3e79f..28d0587b8991 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8094-sony-xperia-kitakami-karin_windy.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb +dtb-$(CONFIG_ARCH_QCOM) += ipq5332-mi01.2.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c1.dtb diff --git a/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts b/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts new file mode 100644 index 000000000000..e86ae14e5613 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts @@ -0,0 +1,71 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * IPQ5332 AP-MI01.2 board device tree source + * + * Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All rights reserved. + */ + +/dts-v1/; + +#include "ipq5332.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. IPQ5332 MI01.2"; + compatible = "qcom,ipq5332-ap-mi01.2", "qcom,ipq5332"; + + aliases { + serial0 = &blsp1_uart0; + }; + + chosen { + stdout-path = "serial0"; + }; +}; + +&blsp1_uart0 { + pinctrl-0 = <&serial_0_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&sdhc { + pinctrl-0 = <&sdc_default_state>; + pinctrl-names = "default"; + non-removable; + status = "okay"; +}; + +&sleep_clk { + clock-frequency = <32000>; +}; + +&xo_board { + clock-frequency = <24000000>; +}; + +/* PINCTRL */ + +&tlmm { + sdc_default_state: sdc-default-state { + clk-pins { + pins = "gpio13"; + function = "sdc_clk"; + drive-strength = <8>; + bias-disable; + }; + + cmd-pins { + pins = "gpio12"; + function = "sdc_cmd"; + drive-strength = <8>; + bias-pull-up; + }; + + data-pins { + pins = "gpio8", "gpio9", "gpio10", "gpio11"; + function = "sdc_data"; + drive-strength = <8>; + bias-pull-up; + }; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/ipq5332.dtsi b/arch/arm64/boot/dts/qcom/ipq5332.dtsi new file mode 100644 index 000000000000..7f0ba2ec339c --- /dev/null +++ b/arch/arm64/boot/dts/qcom/ipq5332.dtsi @@ -0,0 +1,272 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * IPQ5332 device tree source + * + * Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All rights reserved. + */ + +#include <dt-bindings/clock/qcom,ipq5332-gcc.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> + +/ { + interrupt-parent = <&intc>; + #address-cells = <2>; + #size-cells = <2>; + + clocks { + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + }; + + xo_board: xo-board-clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + }; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x0>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + }; + + CPU1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x1>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + }; + + CPU2: cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x2>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + }; + + CPU3: cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x3>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + }; + + L2_0: l2-cache { + compatible = "cache"; + cache-level = <2>; + }; + }; + + firmware { + scm { + compatible = "qcom,scm-ipq5332", "qcom,scm"; + }; + }; + + memory@40000000 { + device_type = "memory"; + /* We expect the bootloader to fill in the size */ + reg = <0x0 0x40000000 0x0 0x0>; + }; + + pmu { + compatible = "arm,cortex-a53-pmu"; + interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + tz_mem: tz@4a600000 { + no-map; + reg = <0x0 0x4a600000 0x0 0x200000>; + }; + }; + + soc@0 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0 0xffffffff>; + + tlmm: pinctrl@1000000 { + compatible = "qcom,ipq5332-tlmm"; + reg = <0x01000000 0x300000>; + interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&tlmm 0 0 53>; + interrupt-controller; + #interrupt-cells = <2>; + + serial_0_pins: serial0-state { + pins = "gpio18", "gpio19"; + function = "blsp0_uart0"; + drive-strength = <8>; + bias-pull-up; + }; + }; + + gcc: clock-controller@1800000 { + compatible = "qcom,ipq5332-gcc"; + reg = <0x01800000 0x80000>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + clock-names = "xo", + "sleep_clk", + "pcie_2lane_phy_pipe_clk", + "pcie_2lane_phy_pipe_clk_x1", + "usb_pcie_wrapper_pipe_clk"; + clocks = <&xo_board>, + <&sleep_clk>, + <0>, + <0>, + <0>; + }; + + sdhc: mmc@7804000 { + compatible = "qcom,ipq5332-sdhci", "qcom,sdhci-msm-v5"; + reg = <0x07804000 0x1000>, <0x07805000 0x1000>; + + interrupts = <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hc_irq", "pwr_irq"; + + clocks = <&gcc GCC_SDCC1_AHB_CLK>, + <&gcc GCC_SDCC1_APPS_CLK>, + <&xo_board>; + clock-names = "iface", "core", "xo"; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + max-frequency = <192000000>; + bus-width = <4>; + status = "disabled"; + }; + + blsp1_uart0: serial@78af000 { + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; + reg = <0x078af000 0x200>; + interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + }; + + intc: interrupt-controller@b000000 { + compatible = "qcom,msm-qgic2"; + reg = <0x0b000000 0x1000>, /* GICD */ + <0x0b002000 0x1000>, /* GICC */ + <0x0b001000 0x1000>, /* GICH */ + <0x0b004000 0x1000>; /* GICV */ + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <3>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x0b00c000 0x3000>; + + v2m0: v2m@0 { + compatible = "arm,gic-v2m-frame"; + reg = <0x00000000 0xffd>; + msi-controller; + }; + + v2m1: v2m@1 { + compatible = "arm,gic-v2m-frame"; + reg = <0x00001000 0xffd>; + msi-controller; + }; + + v2m2: v2m@2 { + compatible = "arm,gic-v2m-frame"; + reg = <0x00002000 0xffd>; + msi-controller; + }; + }; + + timer@b120000 { + compatible = "arm,armv7-timer-mem"; + reg = <0x0b120000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + frame@b120000 { + reg = <0x0b121000 0x1000>, + <0x0b122000 0x1000>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + frame-number = <0>; + }; + + frame@b123000 { + reg = <0x0b123000 0x1000>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + frame-number = <1>; + status = "disabled"; + }; + + frame@b124000 { + reg = <0x0b124000 0x1000>; + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + frame-number = <2>; + status = "disabled"; + }; + + frame@b125000 { + reg = <0x0b125000 0x1000>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + frame-number = <3>; + status = "disabled"; + }; + + frame@b126000 { + reg = <0x0b126000 0x1000>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + frame-number = <4>; + status = "disabled"; + }; + + frame@b127000 { + reg = <0x0b127000 0x1000>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + frame-number = <5>; + status = "disabled"; + }; + + frame@b128000 { + reg = <0x0b128000 0x1000>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + frame-number = <6>; + status = "disabled"; + }; + }; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; + }; +};