@@ -3,12 +3,24 @@ NXP LPC18xx/43xx GPIO controller Device Tree Bindings
Required properties:
- compatible : Should be "nxp,lpc1850-gpio"
-- reg : Address and length of the register set for the device
-- clocks : Clock specifier (see clock bindings for details)
-- gpio-controller : Marks the device node as a GPIO controller.
-- #gpio-cells : Should be two
- - First cell is the GPIO line number
- - Second cell is used to specify polarity
+- reg : List of addresses and lengths of the GPIO controller
+ register sets
+- reg-names : Should be "gpio", "gpio-pin-ic", "gpio-group0-ic" and
+ "gpio-gpoup1-ic"
+- clocks : Phandle and clock specifier pair for GPIO controller
+- resets : Phandle and reset specifier pair for GPIO controller
+- gpio-controller : Marks the device node as a GPIO controller
+- #gpio-cells : Should be two:
+ - The first cell is the GPIO line number
+ - The second cell is used to specify polarity
+- interrupt-controller : Marks the device node as an interrupt controller
+- #interrupt-cells : Should be two:
+ - The first cell is an interrupt number within
+ 0..9 range, for GPIO pin interrupts it is equal
+ to 'nxp,gpio-pin-interrupt' property value of
+ GPIO pin configuration, 8 is for GPIO GROUP0
+ interrupt, 9 is for GPIO GROUP1 interrupt
+ - The second cell is used to specify interrupt type
Optional properties:
- gpio-ranges : Mapping between GPIO and pinctrl
@@ -19,21 +31,29 @@ Example:
gpio: gpio@400f4000 {
compatible = "nxp,lpc1850-gpio";
- reg = <0x400f4000 0x4000>;
+ reg = <0x400f4000 0x4000>, <0x40087000 0x1000>,
+ <0x40088000 0x1000>, <0x40089000 0x1000>;
+ reg-names = "gpio", "gpio-pin-ic",
+ "gpio-group0-ic", "gpio-gpoup1-ic";
clocks = <&ccu1 CLK_CPU_GPIO>;
+ resets = <&rgu 28>;
gpio-controller;
#gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
gpio-ranges = <&pinctrl LPC_GPIO(0,0) LPC_PIN(0,0) 2>,
...
<&pinctrl LPC_GPIO(7,19) LPC_PIN(f,5) 7>;
};
gpio_joystick {
- compatible = "gpio-keys-polled";
+ compatible = "gpio-keys";
...
- button@0 {
+ button0 {
...
+ interrupt-parent = <&gpio>;
+ interrupts = <1 IRQ_TYPE_EDGE_BOTH>;
gpios = <&gpio LPC_GPIO(4,8) GPIO_ACTIVE_LOW>;
};
};
From LPC18xx and LPC43xx User Manuals the GPIO controller consists of the following weakly connected blocks: * GPIO pin interrupt block at 0x40087000, * GPIO GROUP0 interrupt block at 0x40088000, * GPIO GROUP1 interrupt block at 0x40089000, * GPIO port block at 0x400F4000. While all 4 sub-controller blocks have their own I/O addresses, moreover all 3 interrupt blocks are APB0 peripherals and high-speed GPIO block is an AHB slave, according to the hardware manual interrupt controllers and GPIO controller block are seen as a single device, all 4 sub-controllers have the shared reset signal RGU #28 and the same shared clock to access registers CLK_Mx_GPIO on CCU1. The change adds descriptions of the currently missing interrupt controller blocks found on GPIO controller, new added properties are 'reg-names', 'resets', 'interrupt-controller' and '#interrupt-cells', also the example is updated to reflect the changes in device tree binding description. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> --- .../bindings/gpio/nxp,lpc1850-gpio.txt | 38 ++++++++++++++----- 1 file changed, 29 insertions(+), 9 deletions(-)