diff mbox

[v2,3/3] gpiolib: debugfs: identify gpios requested as irq only

Message ID 1432117823-1834-4-git-send-email-grygorii.strashko@linaro.org
State New
Headers show

Commit Message

grygorii.strashko@linaro.org May 20, 2015, 10:30 a.m. UTC
Now many of GPIO drivers implement two interfaces gpiolib and irqchip
which are essentially orthogonal. So, now GPIO line can be requested
in three ways:
1) As pure GPIO (gpioX_request())
2) As pure GPIO IRQ, especially in DT boot case.
  DT:
	interrupt-parent = <&gpio6>;
	interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
  Code:
	platform_get_irq() or of_irq_get()
        request_irq()
3) combination of (1) and (2).

And from GPIO debugfs it could be identified when GPIO is
requested/used or used as IRQ, but there is no way to determine
when GPIO is requested/used as IRQ only.

Such information is useful for debugging, so update GPIO debugfs code
to show marker '<irq-only>' for GPIO lines which are requested/used as
GPIO IRQ only.

After this patch sys/kernel/debug/gpio will produce following output:
  ...
 GPIOs 160-191, platform/4805d000.gpio, gpio:
  gpio-171 ((null)              ) in  hi IRQ-209 <irq-only>

 GPIOs 192-223, platform/48051000.gpio, gpio:
  gpio-203 (vtt_fixed           ) out hi

Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
---
 drivers/gpio/gpiolib.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

Comments

Linus Walleij June 1, 2015, 12:52 p.m. UTC | #1
On Wed, May 20, 2015 at 12:30 PM, Grygorii Strashko
<grygorii.strashko@linaro.org> wrote:

> Now many of GPIO drivers implement two interfaces gpiolib and irqchip
> which are essentially orthogonal. So, now GPIO line can be requested
> in three ways:
> 1) As pure GPIO (gpioX_request())
> 2) As pure GPIO IRQ, especially in DT boot case.
>   DT:
>         interrupt-parent = <&gpio6>;
>         interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
>   Code:
>         platform_get_irq() or of_irq_get()
>         request_irq()
> 3) combination of (1) and (2).
>
> And from GPIO debugfs it could be identified when GPIO is
> requested/used or used as IRQ, but there is no way to determine
> when GPIO is requested/used as IRQ only.
>
> Such information is useful for debugging, so update GPIO debugfs code
> to show marker '<irq-only>' for GPIO lines which are requested/used as
> GPIO IRQ only.
>
> After this patch sys/kernel/debug/gpio will produce following output:
>   ...
>  GPIOs 160-191, platform/4805d000.gpio, gpio:
>   gpio-171 ((null)              ) in  hi IRQ-209 <irq-only>
>
>  GPIOs 192-223, platform/48051000.gpio, gpio:
>   gpio-203 (vtt_fixed           ) out hi
>
> Cc: Johan Hovold <johan@kernel.org>
> Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>

Patch applied.

Yours,
Linus Walleij
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
diff mbox

Patch

diff --git a/drivers/gpio/gpiolib.c b/drivers/gpio/gpiolib.c
index f1dcb5b..d69fc58 100644
--- a/drivers/gpio/gpiolib.c
+++ b/drivers/gpio/gpiolib.c
@@ -2272,8 +2272,11 @@  static void gpiolib_dbg_show(struct seq_file *s, struct gpio_chip *chip)
 			chip->get
 				? (chip->get(chip, i) ? "hi" : "lo")
 				: "?  ");
-		if (is_irq)
+		if (is_irq) {
 			seq_printf(s, " IRQ-%d", gpiod_to_irq(gdesc));
+			if (!test_bit(FLAG_REQUESTED, &gdesc->flags))
+				seq_puts(s, " <irq-only>");
+		}
 		seq_printf(s, "\n");
 	}
 }