| Message ID | 20230217102122.16547-1-chanh@os.amperecomputing.com |
|---|---|
| State | Superseded, archived |
| Headers | show |
| Series | ARM: dts: aspeed: mtmitchell: Enable NCSI | expand |
On 17/02/2023 18:32, Krzysztof Kozlowski wrote: > On 17/02/2023 11:21, Chanh Nguyen wrote: >> Support the mac3 (RGMII4) as an NC-SI stack instead of an MDIO PHY. >> >> The OCP slot #0 and OCP slot #1 use a common the BMC_NCSI signal, >> so we use only one of them at the same time. The OCP slot #0 will >> be enabled by PCA9539's setting by default. >> >> Also, enable the OCP Auxiliary Power during booting. >> >> Signed-off-by: Chanh Nguyen <chanh@os.amperecomputing.com> >> --- >> .../boot/dts/aspeed-bmc-ampere-mtmitchell.dts | 37 ++++++++++++++++++- >> 1 file changed, 36 insertions(+), 1 deletion(-) >> >> diff --git a/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts b/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts >> index 4b91600eaf62..e8a6b1f08d6a 100644 >> --- a/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts >> +++ b/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts >> @@ -251,6 +251,14 @@ >> pinctrl-0 = <&pinctrl_rgmii1_default>; >> }; >> >> +&mac3 { >> + status = "okay"; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&pinctrl_rmii4_default>; >> + clock-names = "MACCLK", "RCLK"; >> + use-ncsi; >> +}; >> + >> &fmc { >> status = "okay"; >> flash@0 { >> @@ -439,6 +447,26 @@ >> status = "okay"; >> }; >> >> +&i2c8 { >> + status = "okay"; >> + >> + pca9539@77 { > > Node names should be generic, so I believe this is "gpio". > https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation > > Best regards, > Krzysztof > Thank Krzysztof, The PCA9539APW is a GPIO expander via I2C. For a generic name, I think the "gpio" is suitable.
diff --git a/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts b/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts index 4b91600eaf62..e8a6b1f08d6a 100644 --- a/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts +++ b/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts @@ -251,6 +251,14 @@ pinctrl-0 = <&pinctrl_rgmii1_default>; }; +&mac3 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rmii4_default>; + clock-names = "MACCLK", "RCLK"; + use-ncsi; +}; + &fmc { status = "okay"; flash@0 { @@ -439,6 +447,26 @@ status = "okay"; }; +&i2c8 { + status = "okay"; + + pca9539@77 { + compatible = "nxp,pca9539"; + reg = <0x77>; + gpio-controller; + #address-cells = <1>; + #size-cells = <0>; + #gpio-cells = <2>; + + bmc-ocp0-en-hog { + gpio-hog; + gpios = <7 GPIO_ACTIVE_LOW>; + output-high; + line-name = "bmc-ocp0-en-n"; + }; + }; +}; + &i2c9 { status = "okay"; }; @@ -530,13 +558,20 @@ /*V0-V7*/ "s0-hightemp-n","s0-fault-alert","s0-sys-auth-failure-n", "host0-reboot-ack-n","host0-ready","host0-shd-req-n", "host0-shd-ack-n","s0-overtemp-n", - /*W0-W7*/ "ocp-aux-pwren","ocp-main-pwren","ocp-pgood","", + /*W0-W7*/ "","ocp-main-pwren","ocp-pgood","", "bmc-ok","bmc-ready","spi0-program-sel","spi0-backup-sel", /*X0-X7*/ "i2c-backup-sel","s1-fault-alert","s1-fw-boot-ok", "s1-hightemp-n","s0-spi-auth-fail-n","s1-sys-auth-failure-n", "s1-overtemp-n","s1-spi-auth-fail-n", /*Y0-Y7*/ "","","","","","","","host0-special-boot", /*Z0-Z7*/ "reset-button","ps0-pgood","ps1-pgood","","","","",""; + + ocp-aux-pwren-hog { + gpio-hog; + gpios = <ASPEED_GPIO(W, 0) GPIO_ACTIVE_HIGH>; + output-high; + line-name = "ocp-aux-pwren"; + }; }; &gpio1 {
Support the mac3 (RGMII4) as an NC-SI stack instead of an MDIO PHY. The OCP slot #0 and OCP slot #1 use a common the BMC_NCSI signal, so we use only one of them at the same time. The OCP slot #0 will be enabled by PCA9539's setting by default. Also, enable the OCP Auxiliary Power during booting. Signed-off-by: Chanh Nguyen <chanh@os.amperecomputing.com> --- .../boot/dts/aspeed-bmc-ampere-mtmitchell.dts | 37 ++++++++++++++++++- 1 file changed, 36 insertions(+), 1 deletion(-)