diff mbox series

rs6000: Use memory_operand for all simple {l,st}*brx instructions

Message ID 2233e8a73834a4fb4f959c2c4ae43a1cdd8fa77e.1574978788.git.segher@kernel.crashing.org
State New
Headers show
Series rs6000: Use memory_operand for all simple {l,st}*brx instructions | expand

Commit Message

Segher Boessenkool Nov. 28, 2019, 10:23 p.m. UTC
We run fwprop before combine, very early even in the case of fwprop1;
and fwprop1 will change memory addressing to what it considers cheaper.
After the "common" change, it now changes the indexed store instruction
in the testcase to be to a constant address.  But that is not an
improvement at all: the byte reverse instructions only exist in the
indexed form, so they will not match anymore.

This patch changes the patterns for the byte reverse instructions to
allow plain memory_operand, letting reload fix this up.

Tested on powerpc64-linux {-m32,-m64}, committing to trunk.


2019-11-28  Segher Boessenkool  <segher@kernel.crashing.org>

	PR target/92602
	* config/rs6000/rs6000.md (bswap<mode>2_load for HSI): Change the
	indexed_or_indirect_operand to be memory_operand.
	(bswap<mode>2_store for HSI): Ditto.
	(bswapdi2_load): Ditto.
	(bswapdi2_store): Ditto.

 gcc/config/rs6000/rs6000.md | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
diff mbox series


diff --git a/gcc/config/rs6000/rs6000.md b/gcc/config/rs6000/rs6000.md
index 876dfe3..0187ba0 100644
--- a/gcc/config/rs6000/rs6000.md
+++ b/gcc/config/rs6000/rs6000.md
@@ -2510,13 +2510,13 @@  (define_expand "bswap<mode>2"
 (define_insn "bswap<mode>2_load"
   [(set (match_operand:HSI 0 "gpc_reg_operand" "=r")
-	(bswap:HSI (match_operand:HSI 1 "indexed_or_indirect_operand" "Z")))]
+	(bswap:HSI (match_operand:HSI 1 "memory_operand" "Z")))]
   "l<wd>brx %0,%y1"
   [(set_attr "type" "load")])
 (define_insn "bswap<mode>2_store"
-  [(set (match_operand:HSI 0 "indexed_or_indirect_operand" "=Z")
+  [(set (match_operand:HSI 0 "memory_operand" "=Z")
 	(bswap:HSI (match_operand:HSI 1 "gpc_reg_operand" "r")))]
   "st<wd>brx %1,%y0"
@@ -2632,13 +2632,13 @@  (define_expand "bswapdi2"
 ;; Power7/cell has ldbrx/stdbrx, so use it directly
 (define_insn "bswapdi2_load"
   [(set (match_operand:DI 0 "gpc_reg_operand" "=r")
-	(bswap:DI (match_operand:DI 1 "indexed_or_indirect_operand" "Z")))]
+	(bswap:DI (match_operand:DI 1 "memory_operand" "Z")))]
   "ldbrx %0,%y1"
   [(set_attr "type" "load")])
 (define_insn "bswapdi2_store"
-  [(set (match_operand:DI 0 "indexed_or_indirect_operand" "=Z")
+  [(set (match_operand:DI 0 "memory_operand" "=Z")
 	(bswap:DI (match_operand:DI 1 "gpc_reg_operand" "r")))]
   "stdbrx %1,%y0"