diff mbox series

[net-next,1/5] dt-bindings: net: Convert Altera TSE bindings to yaml

Message ID 20220826135451.526756-2-maxime.chevallier@bootlin.com
State Changes Requested, archived
Headers show
Series net: altera: tse: phylink conversion | expand

Checks

Context Check Description
robh/checkpatch warning total: 0 errors, 2 warnings, 134 lines checked
robh/patch-applied success
robh/dt-meta-schema fail build log

Commit Message

Maxime Chevallier Aug. 26, 2022, 1:54 p.m. UTC 
This converts the bindings for the Altera Triple-Speed Ethernet to yaml.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
 .../devicetree/bindings/net/altera_tse.txt    | 113 ---------------
 .../devicetree/bindings/net/altr,tse.yaml     | 134 ++++++++++++++++++
 2 files changed, 134 insertions(+), 113 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/net/altera_tse.txt
 create mode 100644 Documentation/devicetree/bindings/net/altr,tse.yaml

Comments

Rob Herring Aug. 28, 2022, 2:21 p.m. UTC | #1 
On Fri, 26 Aug 2022 15:54:47 +0200, Maxime Chevallier wrote:
> This converts the bindings for the Altera Triple-Speed Ethernet to yaml.
> 
> Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
> ---
>  .../devicetree/bindings/net/altera_tse.txt    | 113 ---------------
>  .../devicetree/bindings/net/altr,tse.yaml     | 134 ++++++++++++++++++
>  2 files changed, 134 insertions(+), 113 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/net/altera_tse.txt
>  create mode 100644 Documentation/devicetree/bindings/net/altr,tse.yaml
> 

My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):

yamllint warnings/errors:

dtschema/dtc warnings/errors:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/net/altr,tse.yaml: allOf:1:then:properties:reg-names: {'maxItems': 4, 'items': [{'const': 'control_port'}, {'const': 'rx_csr'}, {'const': 'tx_csr'}, {'const': 's1'}]} should not be valid under {'required': ['maxItems']}
	hint: "maxItems" is not needed with an "items" list
	from schema $id: http://devicetree.org/meta-schemas/items.yaml#
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/net/altr,tse.yaml: allOf:2:then:properties:reg-names: 'oneOf' conditional failed, one must be fixed:
	[{'const': 'control_port'}, {'const': 'rx_csr'}, {'const': 'rx_desc'}, {'const': 'rx_resp'}, {'const': 'tx_csr'}, {'const': 'tx_desc'}] is too long
	[{'const': 'control_port'}, {'const': 'rx_csr'}, {'const': 'rx_desc'}, {'const': 'rx_resp'}, {'const': 'tx_csr'}, {'const': 'tx_desc'}] is too short
	False schema does not allow 6
	1 was expected
	6 is greater than the maximum of 2
	6 is greater than the maximum of 3
	6 is greater than the maximum of 4
	6 is greater than the maximum of 5
	hint: "minItems" is only needed if less than the "items" list length
	from schema $id: http://devicetree.org/meta-schemas/items.yaml#
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/net/altr,tse.yaml: ignoring, error in schema: allOf: 1: then: properties: reg-names
Documentation/devicetree/bindings/net/altr,tse.example.dtb:0:0: /example-0/ethernet@1,00001000: failed to match any schema with compatible: ['altr,tse-msgdma-1.0']
Documentation/devicetree/bindings/net/altr,tse.example.dtb:0:0: /example-0/ethernet@1,00001000/mdio: failed to match any schema with compatible: ['altr,tse-mdio']

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/patch/

This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit.
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/net/altera_tse.txt b/Documentation/devicetree/bindings/net/altera_tse.txt
deleted file mode 100644
index 1d9148ff5130..000000000000
--- a/Documentation/devicetree/bindings/net/altera_tse.txt
+++ /dev/null
@@ -1,113 +0,0 @@ 
-* Altera Triple-Speed Ethernet MAC driver (TSE)
-
-Required properties:
-- compatible: Should be "altr,tse-1.0" for legacy SGDMA based TSE, and should
-		be "altr,tse-msgdma-1.0" for the preferred MSGDMA based TSE.
-		ALTR is supported for legacy device trees, but is deprecated.
-		altr should be used for all new designs.
-- reg: Address and length of the register set for the device. It contains
-  the information of registers in the same order as described by reg-names
-- reg-names: Should contain the reg names
-  "control_port": MAC configuration space region
-  "tx_csr":       xDMA Tx dispatcher control and status space region
-  "tx_desc":      MSGDMA Tx dispatcher descriptor space region
-  "rx_csr" :      xDMA Rx dispatcher control and status space region
-  "rx_desc":      MSGDMA Rx dispatcher descriptor space region
-  "rx_resp":      MSGDMA Rx dispatcher response space region
-  "s1":		  SGDMA descriptor memory
-- interrupts: Should contain the TSE interrupts and its mode.
-- interrupt-names: Should contain the interrupt names
-  "rx_irq":       xDMA Rx dispatcher interrupt
-  "tx_irq":       xDMA Tx dispatcher interrupt
-- rx-fifo-depth: MAC receive FIFO buffer depth in bytes
-- tx-fifo-depth: MAC transmit FIFO buffer depth in bytes
-- phy-mode: See ethernet.txt in the same directory.
-- phy-handle: See ethernet.txt in the same directory.
-- phy-addr: See ethernet.txt in the same directory. A configuration should
-		include phy-handle or phy-addr.
-- altr,has-supplementary-unicast:
-		If present, TSE supports additional unicast addresses.
-		Otherwise additional unicast addresses are not supported.
-- altr,has-hash-multicast-filter:
-		If present, TSE supports a hash based multicast filter.
-		Otherwise, hash-based multicast filtering is not supported.
-
-- mdio device tree subnode: When the TSE has a phy connected to its local
-		mdio, there must be device tree subnode with the following
-		required properties:
-
-	- compatible: Must be "altr,tse-mdio".
-	- #address-cells: Must be <1>.
-	- #size-cells: Must be <0>.
-
-	For each phy on the mdio bus, there must be a node with the following
-	fields:
-
-	- reg: phy id used to communicate to phy.
-	- device_type: Must be "ethernet-phy".
-
-The MAC address will be determined using the optional properties defined in
-ethernet.txt.
-
-Example:
-
-	tse_sub_0_eth_tse_0: ethernet@1,00000000 {
-		compatible = "altr,tse-msgdma-1.0";
-		reg =	<0x00000001 0x00000000 0x00000400>,
-			<0x00000001 0x00000460 0x00000020>,
-			<0x00000001 0x00000480 0x00000020>,
-			<0x00000001 0x000004A0 0x00000008>,
-			<0x00000001 0x00000400 0x00000020>,
-			<0x00000001 0x00000420 0x00000020>;
-		reg-names = "control_port", "rx_csr", "rx_desc", "rx_resp", "tx_csr", "tx_desc";
-		interrupt-parent = <&hps_0_arm_gic_0>;
-		interrupts = <0 41 4>, <0 40 4>;
-		interrupt-names = "rx_irq", "tx_irq";
-		rx-fifo-depth = <2048>;
-		tx-fifo-depth = <2048>;
-		address-bits = <48>;
-		max-frame-size = <1500>;
-		local-mac-address = [ 00 00 00 00 00 00 ];
-		phy-mode = "gmii";
-		altr,has-supplementary-unicast;
-		altr,has-hash-multicast-filter;
-		phy-handle = <&phy0>;
-		mdio {
-			compatible = "altr,tse-mdio";
-			#address-cells = <1>;
-			#size-cells = <0>;
-			phy0: ethernet-phy@0 {
-				reg = <0x0>;
-				device_type = "ethernet-phy";
-			};
-
-			phy1: ethernet-phy@1 {
-				reg = <0x1>;
-				device_type = "ethernet-phy";
-			};
-
-		};
-	};
-
-	tse_sub_1_eth_tse_0: ethernet@1,00001000 {
-		compatible = "altr,tse-msgdma-1.0";
-		reg = 	<0x00000001 0x00001000 0x00000400>,
-			<0x00000001 0x00001460 0x00000020>,
-			<0x00000001 0x00001480 0x00000020>,
-			<0x00000001 0x000014A0 0x00000008>,
-			<0x00000001 0x00001400 0x00000020>,
-			<0x00000001 0x00001420 0x00000020>;
-		reg-names = "control_port", "rx_csr", "rx_desc", "rx_resp", "tx_csr", "tx_desc";
-		interrupt-parent = <&hps_0_arm_gic_0>;
-		interrupts = <0 43 4>, <0 42 4>;
-		interrupt-names = "rx_irq", "tx_irq";
-		rx-fifo-depth = <2048>;
-		tx-fifo-depth = <2048>;
-		address-bits = <48>;
-		max-frame-size = <1500>;
-		local-mac-address = [ 00 00 00 00 00 00 ];
-		phy-mode = "gmii";
-		altr,has-supplementary-unicast;
-		altr,has-hash-multicast-filter;
-		phy-handle = <&phy1>;
-	};
diff --git a/Documentation/devicetree/bindings/net/altr,tse.yaml b/Documentation/devicetree/bindings/net/altr,tse.yaml
new file mode 100644
index 000000000000..24e081cd1aa9
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/altr,tse.yaml
@@ -0,0 +1,134 @@ 
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/altr,tse.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Altera Triple Speed Ethernet MAC driver (TSE)
+
+maintainers:
+  - Maxime Chevallier <maxime.chevallier@bootlin.com>
+
+allOf:
+  - $ref: "ethernet-controller.yaml#"
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - altr,tse-1.0
+              - ALTR,tse-1.0
+    then:
+      properties:
+        reg:
+          maxItems: 4
+        reg-names:
+          maxItems: 4
+          items:
+            - const: control_port
+            - const: rx_csr
+            - const: tx_csr
+            - const: s1
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - altr,tse-msgdma-1.0
+    then:
+      properties:
+        reg:
+          minItems: 6
+        reg-names:
+          minItems: 6
+          items:
+            - const: control_port
+            - const: rx_csr
+            - const: rx_desc
+            - const: rx_resp
+            - const: tx_csr
+            - const: tx_desc
+
+properties:
+  compatible:
+    enum:
+      - altr,tse-1.0
+      - ALTR,tse-1.0
+      - altr,tse-msgdma-1.0
+
+  interrupts:
+    minItems: 2
+
+  interrupt-names:
+    items:
+      - const: rx_irq
+      - const: tx_irq
+
+  rx-fifo-depth:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Depth in bytes of the RX FIFO
+
+  tx-fifo-depth:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Depth in bytes of the TX FIFO
+
+  altr,has_supplementary_unicast:
+    type: boolean
+    description:
+      If present, TSE supports additional unicast addresses.
+
+  altr,has_hash_multicast_filter:
+    type: boolean
+    description:
+      If present, TSE supports hash based multicast filter.
+
+  mdio:
+    $ref: mdio.yaml#
+    unevaluatedProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - rx-fifo-depth
+  - tx-fifo-depth
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    tse_sub_1_eth_tse_0: ethernet@1,00001000 {
+        compatible = "altr,tse-msgdma-1.0";
+        reg = <0x00001000 0x00000400>,
+              <0x00001460 0x00000020>,
+              <0x00001480 0x00000020>,
+              <0x000014A0 0x00000008>,
+              <0x00001400 0x00000020>,
+              <0x00001420 0x00000020>;
+        reg-names = "control_port", "rx_csr", "rx_desc", "rx_resp", "tx_csr", "tx_desc";
+        interrupt-parent = <&hps_0_arm_gic_0>;
+        interrupts = <0 43 4>, <0 42 4>;
+        interrupt-names = "rx_irq", "tx_irq";
+        rx-fifo-depth = <2048>;
+        tx-fifo-depth = <2048>;
+        address-bits = <48>;
+        max-frame-size = <1500>;
+        local-mac-address = [ 00 00 00 00 00 00 ];
+        phy-mode = "gmii";
+        altr,has-supplementary-unicast;
+        altr,has-hash-multicast-filter;
+        phy-handle = <&phy1>;
+        mdio {
+            compatible = "altr,tse-mdio";
+            #address-cells = <1>;
+            #size-cells = <0>;
+            phy1: ethernet-phy@1 {
+                reg = <0x1>;
+            };
+        };
+    };
+
+...