diff mbox series

[1/2] dt-bindings: phy: Introduce Qualcomm eDP/DP PHY binding

Message ID 20210511041930.592483-1-bjorn.andersson@linaro.org
State Changes Requested
Headers show
Series [1/2] dt-bindings: phy: Introduce Qualcomm eDP/DP PHY binding | expand

Checks

Context Check Description
robh/checkpatch success
robh/dt-meta-schema success
robh/dtbs-check success

Commit Message

Bjorn Andersson May 11, 2021, 4:19 a.m. UTC
Introduce a binding for the eDP/DP PHY hardware block found in several
different Qualcomm platforms.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
 .../devicetree/bindings/phy/qcom,edp-phy.yaml | 69 +++++++++++++++++++
 1 file changed, 69 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/qcom,edp-phy.yaml

Comments

Stephen Boyd May 11, 2021, 5:22 a.m. UTC | #1
Quoting Bjorn Andersson (2021-05-10 21:19:30)
> Many recent Qualcomm platforms comes with native DP and eDP support.
> This consists of a controller int he MDSS and a QMP-like PHY.
>
> While similar to the well known QMP block, the eDP PHY only has TX lanes
> and the programming sequences are slightly different. Rather than
> continuing the trend of parameterize the QMP driver to pieces, this
> introduces the support as a new driver.

Thank you for not slamming it into the same mega driver.

>
> The registration of link and pixel clocks are borrowed from the QMP
> driver. The non-DP link frequencies are omitted for now.

Can we make some library code for "DP" stuff in qmp that the two can
call to share the logic?

>
> The eDP PHY is very similar to the dedicated (non-USB) DP PHY, but only
> the prior is supported for now.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> ---
>  drivers/phy/qualcomm/Kconfig        |  10 +
>  drivers/phy/qualcomm/Makefile       |   1 +
>  drivers/phy/qualcomm/phy-qcom-edp.c | 750 ++++++++++++++++++++++++++++
>  3 files changed, 761 insertions(+)
>  create mode 100644 drivers/phy/qualcomm/phy-qcom-edp.c
>
> diff --git a/drivers/phy/qualcomm/Kconfig b/drivers/phy/qualcomm/Kconfig
> index 7f6fcb8ec5ba..13ae6f4f3112 100644
> --- a/drivers/phy/qualcomm/Kconfig
> +++ b/drivers/phy/qualcomm/Kconfig
> @@ -114,3 +114,13 @@ config PHY_QCOM_IPQ806X_USB
>           This option enables support for the Synopsis PHYs present inside the
>           Qualcomm USB3.0 DWC3 controller on ipq806x SoC. This driver supports
>           both HS and SS PHY controllers.
> +
> +config PHY_QCOM_EDP

Can this come somewhere alphabet sorted?

> +       tristate "Qualcomm eDP PHY driver"
> +       depends on ARCH_QCOM || COMPILE_TEST

I wonder if this could be pulled up above for the whole file.

> +       depends on OF
> +       depends on COMMON_CLK
> +       select GENERIC_PHY
> +       help
> +         Enable this driver to support the Qualcomm eDP PHY found in various
> +         Qualcomm chipsets.
> diff --git a/drivers/phy/qualcomm/Makefile b/drivers/phy/qualcomm/Makefile
> index 47acbd7daa3a..1afd0882dbcc 100644
> --- a/drivers/phy/qualcomm/Makefile
> +++ b/drivers/phy/qualcomm/Makefile
> @@ -12,3 +12,4 @@ obj-$(CONFIG_PHY_QCOM_USB_HS_28NM)    += phy-qcom-usb-hs-28nm.o
>  obj-$(CONFIG_PHY_QCOM_USB_SS)          += phy-qcom-usb-ss.o
>  obj-$(CONFIG_PHY_QCOM_USB_SNPS_FEMTO_V2)+= phy-qcom-snps-femto-v2.o
>  obj-$(CONFIG_PHY_QCOM_IPQ806X_USB)             += phy-qcom-ipq806x-usb.o
> +obj-$(CONFIG_PHY_QCOM_EDP)             += phy-qcom-edp.o

Also alphabet sorted instead of tacked onto the end?

> diff --git a/drivers/phy/qualcomm/phy-qcom-edp.c b/drivers/phy/qualcomm/phy-qcom-edp.c
> new file mode 100644
> index 000000000000..ff0508e49548
> --- /dev/null
> +++ b/drivers/phy/qualcomm/phy-qcom-edp.c
> @@ -0,0 +1,750 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2017, 2020, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2021, Linaro Ltd.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/clk-provider.h>
> +#include <linux/delay.h>
> +#include <linux/err.h>
> +#include <linux/io.h>
> +#include <linux/iopoll.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/of_address.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/reset.h>
> +#include <linux/slab.h>
> +
> +#include <dt-bindings/phy/phy.h>
> +
> +#define DP_PHY_PD_CTL_PWRDN                    0x001
> +#define DP_PHY_PD_CTL_PSR_PWRDN                        0x002
> +#define DP_PHY_PD_CTL_AUX_PWRDN                        0x004
> +#define DP_PHY_PD_CTL_LANE_0_1_PWRDN           0x008
> +#define DP_PHY_PD_CTL_LANE_2_3_PWRDN           0x010
> +#define DP_PHY_PD_CTL_PLL_PWRDN                        0x020
> +#define DP_PHY_PD_CTL_DP_CLAMP_EN              0x040
> +
> +#define DP_PHY_CFG                              0x0010
> +#define DP_PHY_CFG_1                            0x0014
> +#define DP_PHY_PD_CTL                           0x001C
> +#define DP_PHY_MODE                             0x0020
> +
> +#define DP_PHY_AUX_CFG0                                0x0020
> +#define DP_PHY_AUX_CFG1                                0x0024
> +#define DP_PHY_AUX_CFG2                                0x0028
> +#define DP_PHY_AUX_CFG3                                0x002c
> +#define DP_PHY_AUX_CFG4                                0x0030
> +#define DP_PHY_AUX_CFG5                                0x0034
> +#define DP_PHY_AUX_CFG6                                0x0038
> +#define DP_PHY_AUX_CFG7                                0x003c
> +#define DP_PHY_AUX_CFG8                                0x0040
> +#define DP_PHY_AUX_CFG9                                0x0044
> +
> +#define DP_PHY_VCO_DIV                          0x0074
> +#define DP_PHY_TX0_TX1_LANE_CTL                 0x007C
> +#define DP_PHY_TX2_TX3_LANE_CTL                 0x00A0
> +
> +#define DP_PHY_SPARE0                           0x00CC
> +#define DP_PHY_STATUS                           0x00E0
> +
> +/* Tx registers */
> +#define TXn_CLKBUF_ENABLE                       0x0000
> +#define TXn_TX_EMP_POST1_LVL                    0x0004
> +
> +#define TXn_TX_DRV_LVL                          0x0014
> +#define TXn_TX_DRV_LVL_OFFSET                   0x0018
> +#define TXn_RESET_TSYNC_EN                      0x001C
> +//#define TXn_PRE_STALL_LDO_BOOST_EN            0x0020
> +#define TXn_LDO_CONFIG                          0x0084
> +#define TXn_TX_BAND                             0x0028
> +#define TXn_INTERFACE_SELECT                    0x0024
> +
> +#define TXn_RES_CODE_LANE_OFFSET_TX0            0x0044
> +#define TXn_RES_CODE_LANE_OFFSET_TX1            0x0048
> +//#define TXn_RES_CODE_LANE_OFFSET_RX           0x0040
> +
> +#define TXn_TRANSCEIVER_BIAS_EN                 0x0054
> +#define TXn_HIGHZ_DRVR_EN                       0x0058
> +#define TXn_TX_POL_INV                          0x005C
> +#define TXn_PARRATE_REC_DETECT_IDLE_EN          0x0060
> +#define TXn_LANE_MODE_1                         0x0064
> +
> +#define TXn_TRAN_DRVR_EMP_EN                    0x0078
> +//#define TXn_TX_INTERFACE_MODE                 0x00BC

Future work? Maybe add a TODO?

> +
> +#define TXn_VMODE_CTRL1                         0x007C
> +
> +/* PLL register offset */
> +#define QSERDES_COM_BG_TIMER                    0x000C
> +#define QSERDES_COM_BIAS_EN_CLKBUFLR_EN         0x0044
> +#define QSERDES_COM_CLK_ENABLE1                 0x0048
> +#define QSERDES_COM_SYS_CLK_CTRL                0x004C
[..]
> +static int qcom_edp_clks_register(struct qcom_edp *edp, struct device_node *np)
> +{
> +       struct clk_init_data init = { };
> +       int ret;
> +
> +       init.ops = &qcom_edp_dp_link_clk_ops;
> +       init.name = "edp_phy_pll_link_clk";
> +       edp->dp_link_hw.init = &init;
> +       ret = devm_clk_hw_register(edp->dev, &edp->dp_link_hw);
> +       if (ret)
> +               return ret;
> +
> +       init.ops = &qcom_edp_dp_pixel_clk_ops;
> +       init.name = "edp_phy_pll_vco_div_clk";
> +       edp->dp_pixel_hw.init = &init;
> +       ret = devm_clk_hw_register(edp->dev, &edp->dp_pixel_hw);
> +       if (ret)
> +               return ret;
> +
> +       ret = of_clk_add_hw_provider(np, qcom_edp_dp_clks_hw_get, edp);
> +       if (ret)
> +               return ret;
> +
> +       /*
> +        * Roll a devm action because the clock provider is the child node, but

Is it still a child node?

> +        * the child node is not actually a device.
> +        */
> +       ret = devm_add_action(edp->dev, phy_clk_release_provider, np);
> +       if (ret)
> +               phy_clk_release_provider(np);
> +
> +       return ret;
> +}
> +
Jeffrey Hugo May 11, 2021, 2:24 p.m. UTC | #2
On Mon, May 10, 2021 at 10:21 PM Bjorn Andersson
<bjorn.andersson@linaro.org> wrote:
>
> Many recent Qualcomm platforms comes with native DP and eDP support.
> This consists of a controller int he MDSS and a QMP-like PHY.

"in the"
Dmitry Baryshkov May 11, 2021, 2:46 p.m. UTC | #3
On Tue, 11 May 2021 at 07:19, Bjorn Andersson
<bjorn.andersson@linaro.org> wrote:
>
> Many recent Qualcomm platforms comes with native DP and eDP support.
> This consists of a controller int he MDSS and a QMP-like PHY.
>
> While similar to the well known QMP block, the eDP PHY only has TX lanes
> and the programming sequences are slightly different. Rather than
> continuing the trend of parameterize the QMP driver to pieces, this
> introduces the support as a new driver.
>
> The registration of link and pixel clocks are borrowed from the QMP
> driver. The non-DP link frequencies are omitted for now.
>
> The eDP PHY is very similar to the dedicated (non-USB) DP PHY, but only
> the prior is supported for now.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> ---
>  drivers/phy/qualcomm/Kconfig        |  10 +
>  drivers/phy/qualcomm/Makefile       |   1 +
>  drivers/phy/qualcomm/phy-qcom-edp.c | 750 ++++++++++++++++++++++++++++
>  3 files changed, 761 insertions(+)
>  create mode 100644 drivers/phy/qualcomm/phy-qcom-edp.c
>
> diff --git a/drivers/phy/qualcomm/Kconfig b/drivers/phy/qualcomm/Kconfig
> index 7f6fcb8ec5ba..13ae6f4f3112 100644
> --- a/drivers/phy/qualcomm/Kconfig
> +++ b/drivers/phy/qualcomm/Kconfig
> @@ -114,3 +114,13 @@ config PHY_QCOM_IPQ806X_USB
>           This option enables support for the Synopsis PHYs present inside the
>           Qualcomm USB3.0 DWC3 controller on ipq806x SoC. This driver supports
>           both HS and SS PHY controllers.
> +

Just a generic suggestion: what about naming it
PHY_QCOM_QMP_EDP/phy-qcom-qmp-edp.c, so that it stays close to the
"big" qmp driver and also so that other qmp parts can follow this
example if we ever split the bg driver in future?

> +config PHY_QCOM_EDP
> +       tristate "Qualcomm eDP PHY driver"
> +       depends on ARCH_QCOM || COMPILE_TEST
> +       depends on OF
> +       depends on COMMON_CLK
> +       select GENERIC_PHY
> +       help
> +         Enable this driver to support the Qualcomm eDP PHY found in various
> +         Qualcomm chipsets.
> diff --git a/drivers/phy/qualcomm/Makefile b/drivers/phy/qualcomm/Makefile
> index 47acbd7daa3a..1afd0882dbcc 100644
> --- a/drivers/phy/qualcomm/Makefile
> +++ b/drivers/phy/qualcomm/Makefile
> @@ -12,3 +12,4 @@ obj-$(CONFIG_PHY_QCOM_USB_HS_28NM)    += phy-qcom-usb-hs-28nm.o
>  obj-$(CONFIG_PHY_QCOM_USB_SS)          += phy-qcom-usb-ss.o
>  obj-$(CONFIG_PHY_QCOM_USB_SNPS_FEMTO_V2)+= phy-qcom-snps-femto-v2.o
>  obj-$(CONFIG_PHY_QCOM_IPQ806X_USB)             += phy-qcom-ipq806x-usb.o
> +obj-$(CONFIG_PHY_QCOM_EDP)             += phy-qcom-edp.o
> diff --git a/drivers/phy/qualcomm/phy-qcom-edp.c b/drivers/phy/qualcomm/phy-qcom-edp.c
> new file mode 100644
> index 000000000000..ff0508e49548
> --- /dev/null
> +++ b/drivers/phy/qualcomm/phy-qcom-edp.c
> @@ -0,0 +1,750 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2017, 2020, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2021, Linaro Ltd.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/clk-provider.h>
> +#include <linux/delay.h>
> +#include <linux/err.h>
> +#include <linux/io.h>
> +#include <linux/iopoll.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/of_address.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/reset.h>
> +#include <linux/slab.h>
> +
> +#include <dt-bindings/phy/phy.h>
> +
> +#define DP_PHY_PD_CTL_PWRDN                    0x001
> +#define DP_PHY_PD_CTL_PSR_PWRDN                        0x002
> +#define DP_PHY_PD_CTL_AUX_PWRDN                        0x004
> +#define DP_PHY_PD_CTL_LANE_0_1_PWRDN           0x008
> +#define DP_PHY_PD_CTL_LANE_2_3_PWRDN           0x010
> +#define DP_PHY_PD_CTL_PLL_PWRDN                        0x020
> +#define DP_PHY_PD_CTL_DP_CLAMP_EN              0x040
> +
> +#define DP_PHY_CFG                              0x0010
> +#define DP_PHY_CFG_1                            0x0014
> +#define DP_PHY_PD_CTL                           0x001C
> +#define DP_PHY_MODE                             0x0020
> +
> +#define DP_PHY_AUX_CFG0                                0x0020
> +#define DP_PHY_AUX_CFG1                                0x0024
> +#define DP_PHY_AUX_CFG2                                0x0028
> +#define DP_PHY_AUX_CFG3                                0x002c
> +#define DP_PHY_AUX_CFG4                                0x0030
> +#define DP_PHY_AUX_CFG5                                0x0034
> +#define DP_PHY_AUX_CFG6                                0x0038
> +#define DP_PHY_AUX_CFG7                                0x003c
> +#define DP_PHY_AUX_CFG8                                0x0040
> +#define DP_PHY_AUX_CFG9                                0x0044
> +
> +#define DP_PHY_VCO_DIV                          0x0074
> +#define DP_PHY_TX0_TX1_LANE_CTL                 0x007C
> +#define DP_PHY_TX2_TX3_LANE_CTL                 0x00A0
> +
> +#define DP_PHY_SPARE0                           0x00CC
> +#define DP_PHY_STATUS                           0x00E0
> +
> +/* Tx registers */
> +#define TXn_CLKBUF_ENABLE                       0x0000
> +#define TXn_TX_EMP_POST1_LVL                    0x0004
> +
> +#define TXn_TX_DRV_LVL                          0x0014
> +#define TXn_TX_DRV_LVL_OFFSET                   0x0018
> +#define TXn_RESET_TSYNC_EN                      0x001C
> +//#define TXn_PRE_STALL_LDO_BOOST_EN            0x0020
> +#define TXn_LDO_CONFIG                          0x0084
> +#define TXn_TX_BAND                             0x0028
> +#define TXn_INTERFACE_SELECT                    0x0024
> +
> +#define TXn_RES_CODE_LANE_OFFSET_TX0            0x0044
> +#define TXn_RES_CODE_LANE_OFFSET_TX1            0x0048
> +//#define TXn_RES_CODE_LANE_OFFSET_RX           0x0040
> +
> +#define TXn_TRANSCEIVER_BIAS_EN                 0x0054
> +#define TXn_HIGHZ_DRVR_EN                       0x0058
> +#define TXn_TX_POL_INV                          0x005C
> +#define TXn_PARRATE_REC_DETECT_IDLE_EN          0x0060
> +#define TXn_LANE_MODE_1                         0x0064
> +
> +#define TXn_TRAN_DRVR_EMP_EN                    0x0078
> +//#define TXn_TX_INTERFACE_MODE                 0x00BC
> +
> +#define TXn_VMODE_CTRL1                         0x007C
> +
> +/* PLL register offset */
> +#define QSERDES_COM_BG_TIMER                    0x000C
> +#define QSERDES_COM_BIAS_EN_CLKBUFLR_EN         0x0044
> +#define QSERDES_COM_CLK_ENABLE1                 0x0048
> +#define QSERDES_COM_SYS_CLK_CTRL                0x004C
> +#define QSERDES_COM_SYSCLK_BUF_ENABLE           0x0050
> +#define QSERDES_COM_PLL_IVCO                    0x0058
> +
> +#define QSERDES_COM_CP_CTRL_MODE0               0x0074
> +#define QSERDES_COM_PLL_RCTRL_MODE0             0x007C
> +#define QSERDES_COM_PLL_CCTRL_MODE0             0x0084
> +#define QSERDES_COM_SYSCLK_EN_SEL               0x0094
> +#define QSERDES_COM_RESETSM_CNTRL               0x009C
> +#define QSERDES_COM_LOCK_CMP_EN                 0x00A4
> +#define QSERDES_COM_LOCK_CMP1_MODE0             0x00AC
> +#define QSERDES_COM_LOCK_CMP2_MODE0             0x00B0
> +
> +#define QSERDES_COM_DEC_START_MODE0             0x00BC
> +#define QSERDES_COM_DIV_FRAC_START1_MODE0       0x00CC
> +#define QSERDES_COM_DIV_FRAC_START2_MODE0       0x00D0
> +#define QSERDES_COM_DIV_FRAC_START3_MODE0       0x00D4
> +#define QSERDES_COM_INTEGLOOP_GAIN0_MODE0       0x00EC
> +#define QSERDES_COM_INTEGLOOP_GAIN1_MODE0       0x00F0
> +#define QSERDES_COM_VCO_TUNE_CTRL               0x0108
> +#define QSERDES_COM_VCO_TUNE_MAP                0x010C
> +#define QSERDES_COM_VCO_TUNE1_MODE0             0x0110
> +#define QSERDES_COM_VCO_TUNE2_MODE0             0x0114
> +#define QSERDES_COM_CMN_STATUS                  0x0140
> +
> +#define QSERDES_COM_CLK_SEL                     0x0154
> +#define QSERDES_COM_HSCLK_SEL                   0x0158
> +
> +#define QSERDES_COM_CORECLK_DIV_MODE0           0x0168
> +
> +#define QSERDES_COM_CORE_CLK_EN                 0x0174
> +#define QSERDES_COM_C_READY_STATUS              0x0178
> +#define QSERDES_COM_CMN_CONFIG                  0x017C
> +
> +#define QSERDES_COM_SVS_MODE_CLK_SEL            0x0184
> +
> +#define QSERDES_COM_SSC_EN_CENTER               0x0010
> +#define QSERDES_COM_SSC_ADJ_PER1                0x0014
> +#define QSERDES_COM_SSC_ADJ_PER2                0x0018
> +#define QSERDES_COM_SSC_PER1                    0x001C
> +#define QSERDES_COM_SSC_PER2                    0x0020
> +#define QSERDES_COM_SSC_STEP_SIZE1_MODE0        0x0024
> +#define QSERDES_COM_SSC_STEP_SIZE2_MODE0        0x0028
> +
> +#define DP_PHY_PLL_POLL_SLEEP_US                500
> +#define DP_PHY_PLL_POLL_TIMEOUT_US              10000
> +
> +#define EDP_VCO_RATE_8100MHZDIV1000             8100000UL
> +#define EDP_VCO_RATE_8640MHZDIV1000             8640000UL
> +#define EDP_VCO_RATE_9720MHZDIV1000             9720000UL
> +#define EDP_VCO_RATE_10800MHZDIV1000            10800000UL
> +#define EDP_VCO_RATE_11880MHZDIV1000            11880000UL

Can we use phy-qcom-qmp.h for register difinitions?

> +
> +struct qcom_edp {
> +       struct device *dev;
> +
> +       struct phy *phy;
> +
> +       void __iomem *edp;
> +       void __iomem *tx0;
> +       void __iomem *tx1;
> +       void __iomem *pll;
> +
> +       struct clk_hw dp_link_hw;
> +       struct clk_hw dp_pixel_hw;
> +
> +       struct phy_configure_opts_dp dp_opts;
> +
> +       struct clk_bulk_data clks[2];
> +       struct regulator_bulk_data supplies[2];
> +} ;
> +
> +static int qcom_edp_phy_init(struct phy *phy)
> +{
> +       struct qcom_edp *edp = phy_get_drvdata(phy);
> +       int ret;
> +
> +       ret = regulator_bulk_enable(ARRAY_SIZE(edp->supplies), edp->supplies);
> +       if (ret)
> +               return ret;
> +
> +       ret = clk_bulk_prepare_enable(ARRAY_SIZE(edp->clks), edp->clks);
> +       if (ret)
> +               goto out_disable_supplies;
> +
> +       writel(DP_PHY_PD_CTL_PWRDN | DP_PHY_PD_CTL_AUX_PWRDN |
> +              DP_PHY_PD_CTL_PLL_PWRDN | DP_PHY_PD_CTL_DP_CLAMP_EN,
> +              edp->edp + DP_PHY_PD_CTL);
> +
> +       writel(0x17, edp->pll + QSERDES_COM_BIAS_EN_CLKBUFLR_EN);
> +
> +       writel(DP_PHY_PD_CTL_PSR_PWRDN, edp->edp + DP_PHY_PD_CTL);
> +       msleep(20);
> +
> +       writel(DP_PHY_PD_CTL_PWRDN | DP_PHY_PD_CTL_AUX_PWRDN |
> +              DP_PHY_PD_CTL_LANE_0_1_PWRDN | DP_PHY_PD_CTL_LANE_2_3_PWRDN |
> +              DP_PHY_PD_CTL_PLL_PWRDN | DP_PHY_PD_CTL_DP_CLAMP_EN,
> +              edp->edp + DP_PHY_PD_CTL);
> +
> +       writel(0x00, edp->edp + DP_PHY_AUX_CFG0);
> +       writel(0x13, edp->edp + DP_PHY_AUX_CFG1);
> +       writel(0x24, edp->edp + DP_PHY_AUX_CFG2);
> +       writel(0x00, edp->edp + DP_PHY_AUX_CFG3);
> +       writel(0x0a, edp->edp + DP_PHY_AUX_CFG4);
> +       writel(0x26, edp->edp + DP_PHY_AUX_CFG5);
> +       writel(0x0a, edp->edp + DP_PHY_AUX_CFG6);
> +       writel(0x03, edp->edp + DP_PHY_AUX_CFG7);
> +       writel(0x37, edp->edp + DP_PHY_AUX_CFG8);
> +       writel(0x03, edp->edp + DP_PHY_AUX_CFG9);
> +
> +       writel(0x1f, edp->edp + 0x58);
> +
> +       msleep(20);
> +
> +       return 0;
> +
> +out_disable_supplies:
> +       regulator_bulk_disable(ARRAY_SIZE(edp->supplies), edp->supplies);
> +
> +       return ret;
> +}
> +
> +static int qcom_edp_phy_configure(struct phy *phy, union phy_configure_opts *opts)
> +{
> +       const struct phy_configure_opts_dp *dp_opts = &opts->dp;
> +       struct qcom_edp *edp = phy_get_drvdata(phy);
> +
> +       memcpy(&edp->dp_opts, dp_opts, sizeof(*dp_opts));
> +
> +       return 0;
> +}
> +
> +static int qcom_edp_configure_ssc(struct qcom_edp *edp)
> +{
> +       const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts;
> +       u32 step1;
> +       u32 step2;
> +
> +       switch (dp_opts->link_rate) {
> +       case 1620:
> +       case 2700:
> +       case 8100:
> +               step1 = 0x45;
> +               step2 = 0x06;
> +               break;
> +       case 5400:
> +               step1 = 0x5c;
> +               step2 = 0x08;
> +               break;
> +       default:
> +               /* Other link rates aren't supported */
> +               return -EINVAL;
> +       }
> +
> +       writel(0x01, edp->pll + QSERDES_COM_SSC_EN_CENTER);
> +       writel(0x00, edp->pll + QSERDES_COM_SSC_ADJ_PER1);
> +       writel(0x36, edp->pll + QSERDES_COM_SSC_PER1);
> +       writel(0x01, edp->pll + QSERDES_COM_SSC_PER2);
> +       writel(step1, edp->pll + QSERDES_COM_SSC_STEP_SIZE1_MODE0);
> +       writel(step2, edp->pll + QSERDES_COM_SSC_STEP_SIZE2_MODE0);
> +
> +       return 0;
> +}
> +
> +static int qcom_edp_configure_pll(struct qcom_edp *edp)
> +{
> +       const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts;
> +       u32 div_frac_start2_mode0;
> +       u32 div_frac_start3_mode0;
> +       u32 dec_start_mode0;
> +       u32 lock_cmp1_mode0;
> +       u32 lock_cmp2_mode0;
> +       u32 hsclk_sel;
> +
> +       switch (dp_opts->link_rate) {
> +       case 1620:
> +               hsclk_sel = 0x5;
> +               dec_start_mode0 = 0x69;
> +               div_frac_start2_mode0 = 0x80;
> +               div_frac_start3_mode0 = 0x07;
> +               lock_cmp1_mode0 = 0x6f;
> +               lock_cmp2_mode0 = 0x08;
> +               break;
> +       case 2700:
> +               hsclk_sel = 0x3;
> +               dec_start_mode0 = 0x69;
> +               div_frac_start2_mode0 = 0x80;
> +               div_frac_start3_mode0 = 0x07;
> +               lock_cmp1_mode0 = 0x0f;
> +               lock_cmp2_mode0 = 0x0e;
> +               break;
> +       case 5400:
> +               hsclk_sel = 0x1;
> +               dec_start_mode0 = 0x8c;
> +               div_frac_start2_mode0 = 0x00;
> +               div_frac_start3_mode0 = 0x0a;
> +               lock_cmp1_mode0 = 0x1f;
> +               lock_cmp2_mode0 = 0x1c;
> +               break;
> +       case 8100:
> +               hsclk_sel = 0x0;
> +               dec_start_mode0 = 0x69;
> +               div_frac_start2_mode0 = 0x80;
> +               div_frac_start3_mode0 = 0x07;
> +               lock_cmp1_mode0 = 0x2f;
> +               lock_cmp2_mode0 = 0x2a;
> +               break;
> +       default:
> +               /* Other link rates aren't supported */
> +               return -EINVAL;
> +       }
> +
> +       writel(0x01, edp->pll + QSERDES_COM_SVS_MODE_CLK_SEL);
> +       writel(0x0b, edp->pll + QSERDES_COM_SYSCLK_EN_SEL);
> +       writel(0x02, edp->pll + QSERDES_COM_SYS_CLK_CTRL);
> +       writel(0x0c, edp->pll + QSERDES_COM_CLK_ENABLE1);
> +       writel(0x06, edp->pll + QSERDES_COM_SYSCLK_BUF_ENABLE);
> +       writel(0x30, edp->pll + QSERDES_COM_CLK_SEL);
> +       writel(hsclk_sel, edp->pll + QSERDES_COM_HSCLK_SEL);
> +       writel(0x0f, edp->pll + QSERDES_COM_PLL_IVCO);
> +       writel(0x08, edp->pll + QSERDES_COM_LOCK_CMP_EN);
> +       writel(0x36, edp->pll + QSERDES_COM_PLL_CCTRL_MODE0);
> +       writel(0x16, edp->pll + QSERDES_COM_PLL_RCTRL_MODE0);
> +       writel(0x06, edp->pll + QSERDES_COM_CP_CTRL_MODE0);
> +       writel(dec_start_mode0, edp->pll + QSERDES_COM_DEC_START_MODE0);
> +       writel(0x00, edp->pll + QSERDES_COM_DIV_FRAC_START1_MODE0);
> +       writel(div_frac_start2_mode0, edp->pll + QSERDES_COM_DIV_FRAC_START2_MODE0);
> +       writel(div_frac_start3_mode0, edp->pll + QSERDES_COM_DIV_FRAC_START3_MODE0);
> +       writel(0x02, edp->pll + QSERDES_COM_CMN_CONFIG);
> +       writel(0x3f, edp->pll + QSERDES_COM_INTEGLOOP_GAIN0_MODE0);
> +       writel(0x00, edp->pll + QSERDES_COM_INTEGLOOP_GAIN1_MODE0);
> +       writel(0x00, edp->pll + QSERDES_COM_VCO_TUNE_MAP);
> +       writel(lock_cmp1_mode0, edp->pll + QSERDES_COM_LOCK_CMP1_MODE0);
> +       writel(lock_cmp2_mode0, edp->pll + QSERDES_COM_LOCK_CMP2_MODE0);
> +
> +       writel(0x0a, edp->pll + QSERDES_COM_BG_TIMER);
> +       writel(0x14, edp->pll + QSERDES_COM_CORECLK_DIV_MODE0);
> +       writel(0x00, edp->pll + QSERDES_COM_VCO_TUNE_CTRL);
> +       writel(0x17, edp->pll + QSERDES_COM_BIAS_EN_CLKBUFLR_EN);
> +       writel(0x0f, edp->pll + QSERDES_COM_CORE_CLK_EN);
> +       writel(0xa0, edp->pll + QSERDES_COM_VCO_TUNE1_MODE0);
> +       writel(0x03, edp->pll + QSERDES_COM_VCO_TUNE2_MODE0);
> +
> +       return 0;
> +}
> +
> +static int qcom_edp_set_vco_div(struct qcom_edp *edp)
> +{
> +       const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts;
> +       unsigned long pixel_freq;
> +       u32 vco_div;
> +
> +       switch (dp_opts->link_rate) {
> +       case 1620:
> +               vco_div = 0x1;
> +               pixel_freq = 1620000000UL / 2;
> +               break;
> +       case 2700:
> +               vco_div = 0x1;
> +               pixel_freq = 2700000000UL / 2;
> +               break;
> +       case 5400:
> +               vco_div = 0x2;
> +               pixel_freq = 5400000000UL / 4;
> +               break;
> +       case 8100:
> +               vco_div = 0x0;
> +               pixel_freq = 8100000000UL / 6;
> +               break;
> +       default:
> +               /* Other link rates aren't supported */
> +               return -EINVAL;
> +       }
> +
> +       writel(vco_div, edp->edp + DP_PHY_VCO_DIV);
> +
> +       clk_set_rate(edp->dp_link_hw.clk, dp_opts->link_rate * 100000);
> +       clk_set_rate(edp->dp_pixel_hw.clk, pixel_freq);
> +
> +       return 0;
> +}
> +
> +static int qcom_edp_phy_power_on(struct phy *phy)
> +{
> +       struct qcom_edp *edp = phy_get_drvdata(phy);
> +       int timeout;
> +       int ret;
> +       u32 val;
> +
> +       writel(DP_PHY_PD_CTL_PWRDN | DP_PHY_PD_CTL_AUX_PWRDN |
> +              DP_PHY_PD_CTL_LANE_0_1_PWRDN | DP_PHY_PD_CTL_LANE_2_3_PWRDN |
> +              DP_PHY_PD_CTL_PLL_PWRDN | DP_PHY_PD_CTL_DP_CLAMP_EN,
> +              edp->edp + DP_PHY_PD_CTL);
> +       writel(0xfc, edp->edp + DP_PHY_MODE);
> +
> +       timeout = readl_poll_timeout(edp->pll + QSERDES_COM_CMN_STATUS,
> +                                    val, val & BIT(7), 5, 200);
> +       if (timeout)
> +               return timeout;
> +
> +       writel(0x01, edp->tx0 + TXn_LDO_CONFIG);
> +       writel(0x01, edp->tx1 + TXn_LDO_CONFIG);
> +       writel(0x00, edp->tx0 + TXn_LANE_MODE_1);
> +       writel(0x00, edp->tx1 + TXn_LANE_MODE_1);
> +
> +       ret = qcom_edp_configure_ssc(edp);
> +       if (ret)
> +               return ret;
> +
> +       ret = qcom_edp_configure_pll(edp);
> +       if (ret)
> +               return ret;
> +
> +       /* TX Lane configuration */
> +       writel(0x05, edp->edp + DP_PHY_TX0_TX1_LANE_CTL);
> +       writel(0x05, edp->edp + DP_PHY_TX2_TX3_LANE_CTL);
> +
> +       /* TX-0 register configuration */
> +       writel(0x03, edp->tx0 + TXn_TRANSCEIVER_BIAS_EN);
> +       writel(0x0f, edp->tx0 + TXn_CLKBUF_ENABLE);
> +       writel(0x03, edp->tx0 + TXn_RESET_TSYNC_EN);
> +       writel(0x01, edp->tx0 + TXn_TRAN_DRVR_EMP_EN);
> +       writel(0x04, edp->tx0 + TXn_TX_BAND);
> +
> +       /* TX-1 register configuration */
> +       writel(0x03, edp->tx1 + TXn_TRANSCEIVER_BIAS_EN);
> +       writel(0x0f, edp->tx1 + TXn_CLKBUF_ENABLE);
> +       writel(0x03, edp->tx1 + TXn_RESET_TSYNC_EN);
> +       writel(0x01, edp->tx1 + TXn_TRAN_DRVR_EMP_EN);
> +       writel(0x04, edp->tx1 + TXn_TX_BAND);
> +
> +       ret = qcom_edp_set_vco_div(edp);
> +       if (ret)
> +               return ret;
> +
> +       writel(0x01, edp->edp + DP_PHY_CFG);
> +        writel(0x05, edp->edp + DP_PHY_CFG);
> +        writel(0x01, edp->edp + DP_PHY_CFG);
> +        writel(0x09, edp->edp + DP_PHY_CFG);
> +
> +        writel(0x20, edp->pll + QSERDES_COM_RESETSM_CNTRL);
> +
> +       timeout = readl_poll_timeout(edp->pll + QSERDES_COM_C_READY_STATUS,
> +                                    val, val & BIT(0), 500, 10000);
> +       if (timeout)
> +               return timeout;
> +
> +       writel(0x19, edp->edp + DP_PHY_CFG);
> +       writel(0x1f, edp->tx0 + TXn_HIGHZ_DRVR_EN);
> +       writel(0x04, edp->tx0 + TXn_HIGHZ_DRVR_EN);
> +       writel(0x00, edp->tx0 + TXn_TX_POL_INV);
> +       writel(0x1f, edp->tx1 + TXn_HIGHZ_DRVR_EN);
> +       writel(0x04, edp->tx1 + TXn_HIGHZ_DRVR_EN);
> +       writel(0x00, edp->tx1 + TXn_TX_POL_INV);
> +       writel(0x10, edp->tx0 + TXn_TX_DRV_LVL_OFFSET);
> +       writel(0x10, edp->tx1 + TXn_TX_DRV_LVL_OFFSET);
> +       writel(0x11, edp->tx0 + TXn_RES_CODE_LANE_OFFSET_TX0);
> +       writel(0x11, edp->tx0 + TXn_RES_CODE_LANE_OFFSET_TX1);
> +       writel(0x11, edp->tx1 + TXn_RES_CODE_LANE_OFFSET_TX0);
> +       writel(0x11, edp->tx1 + TXn_RES_CODE_LANE_OFFSET_TX1);
> +
> +       writel(0x10, edp->tx0 + TXn_TX_EMP_POST1_LVL);
> +       writel(0x10, edp->tx1 + TXn_TX_EMP_POST1_LVL);
> +       writel(0x1f, edp->tx0 + TXn_TX_DRV_LVL);
> +       writel(0x1f, edp->tx1 + TXn_TX_DRV_LVL);
> +
> +       writel(0x4, edp->tx0 + TXn_HIGHZ_DRVR_EN);
> +       writel(0x3, edp->tx0 + TXn_TRANSCEIVER_BIAS_EN);
> +       writel(0x4, edp->tx1 + TXn_HIGHZ_DRVR_EN);
> +       writel(0x0, edp->tx1 + TXn_TRANSCEIVER_BIAS_EN);
> +       writel(0x3, edp->edp + DP_PHY_CFG_1);
> +
> +       writel(0x18, edp->edp + DP_PHY_CFG);
> +       udelay(100);
> +
> +       writel(0x19, edp->edp + DP_PHY_CFG);
> +
> +       return readl_poll_timeout(edp->edp + DP_PHY_STATUS,
> +                                 val, val & BIT(1), 500, 10000);
> +}
> +
> +static int qcom_edp_phy_power_off(struct phy *phy)
> +{
> +       struct qcom_edp *edp = phy_get_drvdata(phy);
> +
> +       writel(DP_PHY_PD_CTL_PSR_PWRDN, edp->edp + DP_PHY_PD_CTL);
> +
> +       return 0;
> +}
> +
> +static int qcom_edp_phy_exit(struct phy *phy)
> +{
> +       struct qcom_edp *edp = phy_get_drvdata(phy);
> +
> +       clk_bulk_disable_unprepare(ARRAY_SIZE(edp->clks), edp->clks);
> +       regulator_bulk_disable(ARRAY_SIZE(edp->supplies), edp->supplies);
> +
> +       return 0;
> +}
> +
> +static const struct phy_ops qcom_edp_ops = {
> +       .init           = qcom_edp_phy_init,
> +       .configure      = qcom_edp_phy_configure,
> +       .power_on       = qcom_edp_phy_power_on,
> +       .power_off      = qcom_edp_phy_power_off,
> +       .exit           = qcom_edp_phy_exit,
> +       .owner          = THIS_MODULE,
> +};
> +
> +/*
> + * Display Port PLL driver block diagram for branch clocks
> + *
> + *              +------------------------------+
> + *              |         DP_VCO_CLK           |
> + *              |                              |
> + *              |    +-------------------+     |
> + *              |    |   (DP PLL/VCO)    |     |
> + *              |    +---------+---------+     |
> + *              |              v               |
> + *              |   +----------+-----------+   |
> + *              |   | hsclk_divsel_clk_src |   |
> + *              |   +----------+-----------+   |
> + *              +------------------------------+
> + *                              |
> + *          +---------<---------v------------>----------+
> + *          |                                           |
> + * +--------v----------------+                          |
> + * |    dp_phy_pll_link_clk  |                          |
> + * |     link_clk            |                          |
> + * +--------+----------------+                          |
> + *          |                                           |
> + *          |                                           |
> + *          v                                           v
> + * Input to DISPCC block                                |
> + * for link clk, crypto clk                             |
> + * and interface clock                                  |
> + *                                                      |
> + *                                                      |
> + *      +--------<------------+-----------------+---<---+
> + *      |                     |                 |
> + * +----v---------+  +--------v-----+  +--------v------+
> + * | vco_divided  |  | vco_divided  |  | vco_divided   |
> + * |    _clk_src  |  |    _clk_src  |  |    _clk_src   |
> + * |              |  |              |  |               |
> + * |divsel_six    |  |  divsel_two  |  |  divsel_four  |
> + * +-------+------+  +-----+--------+  +--------+------+
> + *         |                 |                  |
> + *         v---->----------v-------------<------v
> + *                         |
> + *              +----------+-----------------+
> + *              |   dp_phy_pll_vco_div_clk   |
> + *              +---------+------------------+
> + *                        |
> + *                        v
> + *              Input to DISPCC block
> + *              for DP pixel clock
> + *
> + */
> +static int qcom_edp_dp_pixel_clk_determine_rate(struct clk_hw *hw,
> +                                               struct clk_rate_request *req)
> +{
> +       switch (req->rate) {
> +       case 1620000000UL / 2:
> +       case 2700000000UL / 2:
> +       /* 5.4 and 8.1 GHz are same link rate as 2.7GHz, i.e. div 4 and div 6 */
> +               return 0;
> +       default:
> +               return -EINVAL;
> +       }
> +}
> +
> +static unsigned long
> +qcom_edp_dp_pixel_clk_recalc_rate(struct clk_hw *hw, unsigned long parent_rate)
> +{
> +       const struct qcom_edp *edp = container_of(hw, struct qcom_edp, dp_pixel_hw);
> +       const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts;
> +
> +       switch (dp_opts->link_rate) {
> +       case 1620:
> +               return 1620000000UL / 2;
> +       case 2700:
> +               return 2700000000UL / 2;
> +       case 5400:
> +               return 5400000000UL / 4;
> +       case 8100:
> +               return 8100000000UL / 6;
> +       default:
> +               return 0;
> +       }
> +}
> +
> +static const struct clk_ops qcom_edp_dp_pixel_clk_ops = {
> +       .determine_rate = qcom_edp_dp_pixel_clk_determine_rate,
> +       .recalc_rate = qcom_edp_dp_pixel_clk_recalc_rate,
> +};
> +
> +static int qcom_edp_dp_link_clk_determine_rate(struct clk_hw *hw,
> +                                              struct clk_rate_request *req)
> +{
> +       switch (req->rate) {
> +       case 162000000:
> +       case 270000000:
> +       case 540000000:
> +       case 810000000:
> +               return 0;
> +       default:
> +               return -EINVAL;
> +       }
> +}
> +
> +static unsigned long
> +qcom_edp_dp_link_clk_recalc_rate(struct clk_hw *hw, unsigned long parent_rate)
> +{
> +       const struct qcom_edp *edp = container_of(hw, struct qcom_edp, dp_link_hw);
> +       const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts;
> +
> +       switch (dp_opts->link_rate) {
> +       case 1620:
> +       case 2700:
> +       case 5400:
> +       case 8100:
> +               return dp_opts->link_rate * 100000;
> +       default:
> +               return 0;
> +       }
> +}
> +
> +static const struct clk_ops qcom_edp_dp_link_clk_ops = {
> +       .determine_rate = qcom_edp_dp_link_clk_determine_rate,
> +       .recalc_rate = qcom_edp_dp_link_clk_recalc_rate,
> +};
> +
> +static struct clk_hw *
> +qcom_edp_dp_clks_hw_get(struct of_phandle_args *clkspec, void *data)
> +{
> +       unsigned int idx = clkspec->args[0];
> +       struct qcom_edp *edp = data;
> +
> +       if (idx >= 2) {
> +               pr_err("%s: invalid index %u\n", __func__, idx);
> +               return ERR_PTR(-EINVAL);
> +       }
> +
> +       if (idx == 0)
> +               return &edp->dp_link_hw;
> +
> +       return &edp->dp_pixel_hw;
> +}
> +
> +static void phy_clk_release_provider(void *res)
> +{
> +       of_clk_del_provider(res);
> +}
> +
> +static int qcom_edp_clks_register(struct qcom_edp *edp, struct device_node *np)
> +{
> +       struct clk_init_data init = { };
> +       int ret;
> +
> +       init.ops = &qcom_edp_dp_link_clk_ops;
> +       init.name = "edp_phy_pll_link_clk";
> +       edp->dp_link_hw.init = &init;
> +       ret = devm_clk_hw_register(edp->dev, &edp->dp_link_hw);
> +       if (ret)
> +               return ret;
> +
> +       init.ops = &qcom_edp_dp_pixel_clk_ops;
> +       init.name = "edp_phy_pll_vco_div_clk";
> +       edp->dp_pixel_hw.init = &init;
> +       ret = devm_clk_hw_register(edp->dev, &edp->dp_pixel_hw);
> +       if (ret)
> +               return ret;
> +
> +       ret = of_clk_add_hw_provider(np, qcom_edp_dp_clks_hw_get, edp);

I think we can use of_clk_onecell_get here (and we should change main
qmp driver)
Also we can use devm_of_clk_add_hw_provider.

> +       if (ret)
> +               return ret;
> +
> +       /*
> +        * Roll a devm action because the clock provider is the child node, but
> +        * the child node is not actually a device.
> +        */
> +       ret = devm_add_action(edp->dev, phy_clk_release_provider, np);
> +       if (ret)
> +               phy_clk_release_provider(np);
> +
> +       return ret;
> +}
> +
> +static int qcom_edp_phy_probe(struct platform_device *pdev)
> +{
> +       struct phy_provider *phy_provider;
> +       struct device *dev = &pdev->dev;
> +       struct qcom_edp *edp;
> +       int ret;
> +
> +       edp = devm_kzalloc(dev, sizeof(*edp), GFP_KERNEL);
> +       if (!edp)
> +               return -ENOMEM;
> +
> +       edp->dev = dev;
> +
> +       edp->edp = devm_platform_ioremap_resource(pdev, 0);
> +       if (IS_ERR(edp->edp))
> +               return PTR_ERR(edp->edp);
> +
> +       edp->tx0 = devm_platform_ioremap_resource(pdev, 1);
> +       if (IS_ERR(edp->tx0))
> +               return PTR_ERR(edp->tx0);
> +
> +       edp->tx1 = devm_platform_ioremap_resource(pdev, 2);
> +       if (IS_ERR(edp->tx1))
> +               return PTR_ERR(edp->tx1);
> +
> +       edp->pll = devm_platform_ioremap_resource(pdev, 3);
> +       if (IS_ERR(edp->pll))
> +               return PTR_ERR(edp->pll);
> +
> +       edp->clks[0].id = "aux";
> +       edp->clks[1].id = "cfg_ahb";
> +       ret = devm_clk_bulk_get(dev, ARRAY_SIZE(edp->clks), edp->clks);
> +       if (ret)
> +               return ret;
> +
> +       edp->supplies[0].supply = "vdda-phy";
> +       edp->supplies[1].supply = "vdda-pll";
> +       ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(edp->supplies), edp->supplies);
> +       if (ret)
> +               return ret;
> +
> +       ret = qcom_edp_clks_register(edp, pdev->dev.of_node);
> +       if (ret)
> +               return ret;
> +
> +       edp->phy = devm_phy_create(dev, pdev->dev.of_node, &qcom_edp_ops);
> +       if (IS_ERR(edp->phy)) {
> +               dev_err(dev, "failed to register phy\n");
> +               return PTR_ERR(edp->phy);
> +       }
> +
> +       phy_set_drvdata(edp->phy, edp);
> +
> +       phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> +       return PTR_ERR_OR_ZERO(phy_provider);
> +}
> +
> +static const struct of_device_id qcom_edp_phy_match_table[] = {
> +       { .compatible = "qcom,sc8180x-edp-phy" },
> +       { }
> +};
> +MODULE_DEVICE_TABLE(of, qcom_edp_phy_match_table);
> +
> +static struct platform_driver qcom_edp_phy_driver = {
> +       .probe          = qcom_edp_phy_probe,
> +       .driver = {
> +               .name   = "qcom-edp-phy",
> +               .of_match_table = qcom_edp_phy_match_table,
> +       },
> +};
> +
> +module_platform_driver(qcom_edp_phy_driver);
> +
> +MODULE_DESCRIPTION("Qualcomm eDP PHY driver");
> +MODULE_LICENSE("GPL v2");
> --
> 2.29.2
>
Stephen Boyd May 11, 2021, 5:24 p.m. UTC | #4
Quoting Bjorn Andersson (2021-05-10 21:19:29)
> diff --git a/Documentation/devicetree/bindings/phy/qcom,edp-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,edp-phy.yaml
> new file mode 100644
> index 000000000000..c258e4f7e332
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/qcom,edp-phy.yaml
> @@ -0,0 +1,69 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +
> +%YAML 1.2
> +---
> +$id: "http://devicetree.org/schemas/phy/qcom,edp-phy.yaml#"
> +$schema: "http://devicetree.org/meta-schemas/core.yaml#"
> +
> +title: Qualcomm DP/eDP PHY
> +
> +maintainers:
> +  - Bjorn Andersson <bjorn.andersson@linaro.org>
> +
> +description:
> +  The Qualcomm DP/eDP PHY is found in a number of Qualcomm platform and
> +  provides the physical interface for DisplayPort and Embedded Display Port.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - qcom,sc8180x-dp-phy
> +      - qcom,sc8180x-edp-phy
> +
> +  reg:
> +    items:
> +      - description: PHY base register block
> +      - description: tx0 register block
> +      - description: tx1 register block
> +      - description: PLL register block
> +
> +  clocks:
> +    maxItems: 2

Can this be items: - const: again? I think having maxItems means you can
have one or two items, which wouldn't match the number of clock-names
then.

> +
> +  clock-names:
> +    items:
> +      - const: aux
> +      - const: cfg_ahb
> +
Vinod Koul May 14, 2021, 10:38 a.m. UTC | #5
On 10-05-21, 22:22, Stephen Boyd wrote:
> Quoting Bjorn Andersson (2021-05-10 21:19:30)
> > Many recent Qualcomm platforms comes with native DP and eDP support.
> > This consists of a controller int he MDSS and a QMP-like PHY.
> >
> > While similar to the well known QMP block, the eDP PHY only has TX lanes
> > and the programming sequences are slightly different. Rather than
> > continuing the trend of parameterize the QMP driver to pieces, this
> > introduces the support as a new driver.
> 
> Thank you for not slamming it into the same mega driver.
> 
> >
> > The registration of link and pixel clocks are borrowed from the QMP
> > driver. The non-DP link frequencies are omitted for now.
> 
> Can we make some library code for "DP" stuff in qmp that the two can
> call to share the logic?

I think we should split QMP into a library of common code which the
respective function driver DP, UFS, USB QMP drivers (re)use across...
Vinod Koul May 14, 2021, 10:40 a.m. UTC | #6
On 10-05-21, 23:19, Bjorn Andersson wrote:

> +static int qcom_edp_phy_power_on(struct phy *phy)
> +{
> +	struct qcom_edp *edp = phy_get_drvdata(phy);
> +	int timeout;
> +	int ret;
> +	u32 val;
> +
> +	writel(DP_PHY_PD_CTL_PWRDN | DP_PHY_PD_CTL_AUX_PWRDN |
> +	       DP_PHY_PD_CTL_LANE_0_1_PWRDN | DP_PHY_PD_CTL_LANE_2_3_PWRDN |
> +	       DP_PHY_PD_CTL_PLL_PWRDN | DP_PHY_PD_CTL_DP_CLAMP_EN,
> +	       edp->edp + DP_PHY_PD_CTL);
> +	writel(0xfc, edp->edp + DP_PHY_MODE);
> +
> +	timeout = readl_poll_timeout(edp->pll + QSERDES_COM_CMN_STATUS,
> +				     val, val & BIT(7), 5, 200);
> +	if (timeout)
> +		return timeout;
> +
> +	writel(0x01, edp->tx0 + TXn_LDO_CONFIG);
> +	writel(0x01, edp->tx1 + TXn_LDO_CONFIG);
> +	writel(0x00, edp->tx0 + TXn_LANE_MODE_1);
> +	writel(0x00, edp->tx1 + TXn_LANE_MODE_1);
> +
> +	ret = qcom_edp_configure_ssc(edp);
> +	if (ret)
> +		return ret;
> +
> +	ret = qcom_edp_configure_pll(edp);
> +	if (ret)
> +		return ret;
> +
> +	/* TX Lane configuration */
> +	writel(0x05, edp->edp + DP_PHY_TX0_TX1_LANE_CTL);
> +	writel(0x05, edp->edp + DP_PHY_TX2_TX3_LANE_CTL);
> +
> +	/* TX-0 register configuration */
> +	writel(0x03, edp->tx0 + TXn_TRANSCEIVER_BIAS_EN);
> +	writel(0x0f, edp->tx0 + TXn_CLKBUF_ENABLE);
> +	writel(0x03, edp->tx0 + TXn_RESET_TSYNC_EN);
> +	writel(0x01, edp->tx0 + TXn_TRAN_DRVR_EMP_EN);
> +	writel(0x04, edp->tx0 + TXn_TX_BAND);
> +
> +	/* TX-1 register configuration */
> +	writel(0x03, edp->tx1 + TXn_TRANSCEIVER_BIAS_EN);
> +	writel(0x0f, edp->tx1 + TXn_CLKBUF_ENABLE);
> +	writel(0x03, edp->tx1 + TXn_RESET_TSYNC_EN);
> +	writel(0x01, edp->tx1 + TXn_TRAN_DRVR_EMP_EN);
> +	writel(0x04, edp->tx1 + TXn_TX_BAND);
> +
> +	ret = qcom_edp_set_vco_div(edp);
> +	if (ret)
> +		return ret;
> +
> +	writel(0x01, edp->edp + DP_PHY_CFG);
> +        writel(0x05, edp->edp + DP_PHY_CFG);
> +        writel(0x01, edp->edp + DP_PHY_CFG);
> +        writel(0x09, edp->edp + DP_PHY_CFG);
> +
> +        writel(0x20, edp->pll + QSERDES_COM_RESETSM_CNTRL);	
> +
> +	timeout = readl_poll_timeout(edp->pll + QSERDES_COM_C_READY_STATUS,
> +				     val, val & BIT(0), 500, 10000);
> +	if (timeout)
> +		return timeout;
> +
> +	writel(0x19, edp->edp + DP_PHY_CFG);
> +	writel(0x1f, edp->tx0 + TXn_HIGHZ_DRVR_EN);
> +	writel(0x04, edp->tx0 + TXn_HIGHZ_DRVR_EN);
> +	writel(0x00, edp->tx0 + TXn_TX_POL_INV);
> +	writel(0x1f, edp->tx1 + TXn_HIGHZ_DRVR_EN);
> +	writel(0x04, edp->tx1 + TXn_HIGHZ_DRVR_EN);
> +	writel(0x00, edp->tx1 + TXn_TX_POL_INV);
> +	writel(0x10, edp->tx0 + TXn_TX_DRV_LVL_OFFSET);
> +	writel(0x10, edp->tx1 + TXn_TX_DRV_LVL_OFFSET);
> +	writel(0x11, edp->tx0 + TXn_RES_CODE_LANE_OFFSET_TX0);
> +	writel(0x11, edp->tx0 + TXn_RES_CODE_LANE_OFFSET_TX1);
> +	writel(0x11, edp->tx1 + TXn_RES_CODE_LANE_OFFSET_TX0);
> +	writel(0x11, edp->tx1 + TXn_RES_CODE_LANE_OFFSET_TX1);
> +
> +	writel(0x10, edp->tx0 + TXn_TX_EMP_POST1_LVL);
> +	writel(0x10, edp->tx1 + TXn_TX_EMP_POST1_LVL);
> +	writel(0x1f, edp->tx0 + TXn_TX_DRV_LVL);
> +	writel(0x1f, edp->tx1 + TXn_TX_DRV_LVL);
> +
> +	writel(0x4, edp->tx0 + TXn_HIGHZ_DRVR_EN);
> +	writel(0x3, edp->tx0 + TXn_TRANSCEIVER_BIAS_EN);
> +	writel(0x4, edp->tx1 + TXn_HIGHZ_DRVR_EN);
> +	writel(0x0, edp->tx1 + TXn_TRANSCEIVER_BIAS_EN);
> +	writel(0x3, edp->edp + DP_PHY_CFG_1);
> +
> +	writel(0x18, edp->edp + DP_PHY_CFG);

Can't help but think that this should be made modular. We would come up
with next set which would have different set of sequence/values so
having a qmp style table here would be better..
Rob Herring May 17, 2021, 9:46 p.m. UTC | #7
On Tue, May 11, 2021 at 10:24:06AM -0700, Stephen Boyd wrote:
> Quoting Bjorn Andersson (2021-05-10 21:19:29)
> > diff --git a/Documentation/devicetree/bindings/phy/qcom,edp-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,edp-phy.yaml
> > new file mode 100644
> > index 000000000000..c258e4f7e332
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/phy/qcom,edp-phy.yaml
> > @@ -0,0 +1,69 @@
> > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> > +
> > +%YAML 1.2
> > +---
> > +$id: "http://devicetree.org/schemas/phy/qcom,edp-phy.yaml#"
> > +$schema: "http://devicetree.org/meta-schemas/core.yaml#"
> > +
> > +title: Qualcomm DP/eDP PHY
> > +
> > +maintainers:
> > +  - Bjorn Andersson <bjorn.andersson@linaro.org>
> > +
> > +description:
> > +  The Qualcomm DP/eDP PHY is found in a number of Qualcomm platform and
> > +  provides the physical interface for DisplayPort and Embedded Display Port.
> > +
> > +properties:
> > +  compatible:
> > +    enum:
> > +      - qcom,sc8180x-dp-phy
> > +      - qcom,sc8180x-edp-phy

Is there a difference in DP and eDP?

> > +
> > +  reg:
> > +    items:
> > +      - description: PHY base register block
> > +      - description: tx0 register block
> > +      - description: tx1 register block
> > +      - description: PLL register block
> > +
> > +  clocks:
> > +    maxItems: 2
> 
> Can this be items: - const: again? I think having maxItems means you can
> have one or two items, which wouldn't match the number of clock-names
> then.

No, it's implicitly 'minItems: 2'. But you can have 'items' if a 
description of each clock is useful.

> 
> > +
> > +  clock-names:
> > +    items:
> > +      - const: aux
> > +      - const: cfg_ahb
> > +
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/phy/qcom,edp-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,edp-phy.yaml
new file mode 100644
index 000000000000..c258e4f7e332
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom,edp-phy.yaml
@@ -0,0 +1,69 @@ 
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/phy/qcom,edp-phy.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Qualcomm DP/eDP PHY
+
+maintainers:
+  - Bjorn Andersson <bjorn.andersson@linaro.org>
+
+description:
+  The Qualcomm DP/eDP PHY is found in a number of Qualcomm platform and
+  provides the physical interface for DisplayPort and Embedded Display Port.
+
+properties:
+  compatible:
+    enum:
+      - qcom,sc8180x-dp-phy
+      - qcom,sc8180x-edp-phy
+
+  reg:
+    items:
+      - description: PHY base register block
+      - description: tx0 register block
+      - description: tx1 register block
+      - description: PLL register block
+
+  clocks:
+    maxItems: 2
+
+  clock-names:
+    items:
+      - const: aux
+      - const: cfg_ahb
+
+  "#clock-cells":
+    const: 1
+
+  "#phy-cells":
+    const: 0
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - "#clock-cells"
+  - "#phy-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    phy@aec2a00 {
+      compatible = "qcom,sc8180x-edp-phy";
+      reg = <0x0aec2a00 0x1c0>,
+            <0x0aec2200 0xa0>,
+            <0x0aec2600 0xa0>,
+            <0x0aec2000 0x19c>;
+
+      clocks = <&dispcc 0>, <&dispcc 1>;
+      clock-names = "aux", "cfg_ahb";
+
+      #clock-cells = <1>;
+      #phy-cells = <0>;
+    };
+...