Message ID | 20201014085316.11916-1-o.rempel@pengutronix.de |
---|---|
State | Superseded, archived |
Headers | show |
Series | [v1,1/3] dt-bindings: vendor-prefixes: Add an entry for Van der Laan b.v. | expand |
Context | Check | Description |
---|---|---|
robh/checkpatch | success | |
robh/dt-meta-schema | success |
Hi Oleksij, pls can you send a patch adding this board to: Documentation/devicetree/bindings/arm/fsl.yaml infront of this patch? On 20-10-14 10:53, Oleksij Rempel wrote: > Van der Laan LANMCU is a module for the food storage rooms to control > proper gas composition. > > Co-Developed-by: Robin van der Gracht <robin@protonic.nl> > Signed-off-by: Robin van der Gracht <robin@protonic.nl> > Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/imx6dl-lanmcu.dts | 468 ++++++++++++++++++++++++++++ > 2 files changed, 469 insertions(+) > create mode 100644 arch/arm/boot/dts/imx6dl-lanmcu.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 2289a28c0ff6..dc2543a7b7e9 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -447,6 +447,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ > imx6dl-icore.dtb \ > imx6dl-icore-mipi.dtb \ > imx6dl-icore-rqs.dtb \ > + imx6dl-lanmcu.dtb \ > imx6dl-mamoj.dtb \ > imx6dl-nit6xlite.dtb \ > imx6dl-nitrogen6x.dtb \ > diff --git a/arch/arm/boot/dts/imx6dl-lanmcu.dts b/arch/arm/boot/dts/imx6dl-lanmcu.dts > new file mode 100644 > index 000000000000..60336c972286 > --- /dev/null > +++ b/arch/arm/boot/dts/imx6dl-lanmcu.dts > @@ -0,0 +1,468 @@ > +// SPDX-License-Identifier: GPL-2.0-or-later > +/* > + * Copyright (c) 2019 Protonic Holland > + * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix > + */ > + > +/dts-v1/; > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/leds/common.h> > +#include "imx6dl.dtsi" > + > +/ { ... > +&fec { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_enet>; > + phy-mode = "rmii"; > + clocks = <&clks IMX6QDL_CLK_ENET>, > + <&clks IMX6QDL_CLK_ENET>, > + <&clock_ksz8081>; > + clock-names = "ipg", "ahb", "ptp"; > + status = "okay"; > + > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + > + /* Microchip KSZ8081RNA PHY */ > + rgmii_phy: ethernet-phy@0 { Do you need this phandle here? > + reg = <0>; > + interrupts-extended = <&gpio5 23 IRQ_TYPE_LEVEL_LOW>; > + reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>; > + reset-assert-us = <10000>; > + reset-deassert-us = <300>; > + }; > + }; > +}; ... > +&i2c3 { > + clock-frequency = <100000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c3>; > + status = "okay"; > + > + edt-ft5406@38 { Please use generic names like: touchscreen@38 or touchcontroller@38. > + compatible = "edt,edt-ft5406"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_ts_edt>; > + reg = <0x38>; reg should be 2nd entry. > + interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>; > + > + touchscreen-size-x = <1792>; > + touchscreen-size-y = <1024>; > + > + touchscreen-fuzz-x = <0>; > + touchscreen-fuzz-y = <0>; > + > + /* Touch screen calibration */ > + threshold = <50>; > + gain = <5>; > + offset = <10>; > + }; > + > + rtc@51 { > + compatible = "nxp,pcf8563"; > + reg = <0x51>; > + }; > +}; ... > +&usdhc2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usdhc2>; > + no-1-8-v; > + non-removable; > + mmc-pwrseq = <&usdhc2_wifi_pwrseq>; > + status = "okay"; status is always the last property of this list. > + #address-cells = <1>; > + #size-cells = <0>; > + > + brcmf: bcrmf@1 { > + reg = <1>; > + compatible = "brcm,bcm4329-fmac"; > + }; > +}; Regards, Marco
Hi Marco, thank you for review! On Wed, Oct 14, 2020 at 12:05:01PM +0200, Marco Felsch wrote: > Hi Oleksij, > > pls can you send a patch adding this board to: > Documentation/devicetree/bindings/arm/fsl.yaml > > infront of this patch? This is patch 3/3 and fsl.yaml 2/3. Do I'm missing some thing? > On 20-10-14 10:53, Oleksij Rempel wrote: > > Van der Laan LANMCU is a module for the food storage rooms to control > > proper gas composition. > > > > Co-Developed-by: Robin van der Gracht <robin@protonic.nl> > > Signed-off-by: Robin van der Gracht <robin@protonic.nl> > > Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> > > --- > > arch/arm/boot/dts/Makefile | 1 + > > arch/arm/boot/dts/imx6dl-lanmcu.dts | 468 ++++++++++++++++++++++++++++ > > 2 files changed, 469 insertions(+) > > create mode 100644 arch/arm/boot/dts/imx6dl-lanmcu.dts > > > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > > index 2289a28c0ff6..dc2543a7b7e9 100644 > > --- a/arch/arm/boot/dts/Makefile > > +++ b/arch/arm/boot/dts/Makefile > > @@ -447,6 +447,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ > > imx6dl-icore.dtb \ > > imx6dl-icore-mipi.dtb \ > > imx6dl-icore-rqs.dtb \ > > + imx6dl-lanmcu.dtb \ > > imx6dl-mamoj.dtb \ > > imx6dl-nit6xlite.dtb \ > > imx6dl-nitrogen6x.dtb \ > > diff --git a/arch/arm/boot/dts/imx6dl-lanmcu.dts b/arch/arm/boot/dts/imx6dl-lanmcu.dts > > new file mode 100644 > > index 000000000000..60336c972286 > > --- /dev/null > > +++ b/arch/arm/boot/dts/imx6dl-lanmcu.dts > > @@ -0,0 +1,468 @@ > > +// SPDX-License-Identifier: GPL-2.0-or-later > > +/* > > + * Copyright (c) 2019 Protonic Holland > > + * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix > > + */ > > + > > +/dts-v1/; > > +#include <dt-bindings/gpio/gpio.h> > > +#include <dt-bindings/leds/common.h> > > +#include "imx6dl.dtsi" > > + > > +/ { > > ... > > > +&fec { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_enet>; > > + phy-mode = "rmii"; > > + clocks = <&clks IMX6QDL_CLK_ENET>, > > + <&clks IMX6QDL_CLK_ENET>, > > + <&clock_ksz8081>; > > + clock-names = "ipg", "ahb", "ptp"; > > + status = "okay"; > > + > > + mdio { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + /* Microchip KSZ8081RNA PHY */ > > + rgmii_phy: ethernet-phy@0 { > > Do you need this phandle here? Fixed by adding phy-handle. > > + reg = <0>; > > + interrupts-extended = <&gpio5 23 IRQ_TYPE_LEVEL_LOW>; > > + reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>; > > + reset-assert-us = <10000>; > > + reset-deassert-us = <300>; > > + }; > > + }; > > +}; > > ... > > > +&i2c3 { > > + clock-frequency = <100000>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_i2c3>; > > + status = "okay"; > > + > > + edt-ft5406@38 { > > Please use generic names like: touchscreen@38 or touchcontroller@38. OK, i'll use "touchscreen@38". touchcontroller@ this variant was never used in the mainline kernel. > > + compatible = "edt,edt-ft5406"; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_ts_edt>; > > + reg = <0x38>; > > reg should be 2nd entry. done > > + interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>; > > + > > + touchscreen-size-x = <1792>; > > + touchscreen-size-y = <1024>; > > + > > + touchscreen-fuzz-x = <0>; > > + touchscreen-fuzz-y = <0>; > > + > > + /* Touch screen calibration */ > > + threshold = <50>; > > + gain = <5>; > > + offset = <10>; > > + }; > > + > > + rtc@51 { > > + compatible = "nxp,pcf8563"; > > + reg = <0x51>; > > + }; > > +}; > > ... > > > +&usdhc2 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_usdhc2>; > > + no-1-8-v; > > + non-removable; > > + mmc-pwrseq = <&usdhc2_wifi_pwrseq>; > > + status = "okay"; > > status is always the last property of this list. done > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + brcmf: bcrmf@1 { > > + reg = <1>; > > + compatible = "brcm,bcm4329-fmac"; > > + }; > > +}; > Regards, Oleksij
On 20-10-15 11:02, Oleksij Rempel wrote: > Hi Marco, > > thank you for review! > > On Wed, Oct 14, 2020 at 12:05:01PM +0200, Marco Felsch wrote: > > Hi Oleksij, > > > > pls can you send a patch adding this board to: > > Documentation/devicetree/bindings/arm/fsl.yaml > > > > infront of this patch? > > This is patch 3/3 and fsl.yaml 2/3. Do I'm missing some thing? Argh.. didn't saw this patch 2/3.. Regards, Marco
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index 801cc267349d..a570f96348a7 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -1120,6 +1120,8 @@ patternProperties: description: Vamrs Ltd. "^variscite,.*": description: Variscite Ltd. + "^vdl,.*": + description: Van der Laan b.v. "^via,.*": description: VIA Technologies, Inc. "^videostrong,.*":
Add "vdl" entry for Van der Laan b.v.: https://www.teamvdl.nl/ Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> --- Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+)