diff --git a/Documentation/devicetree/bindings/mfd/max77686.txt b/Documentation/devicetree/bindings/mfd/max77686.txt
index d2ed3c20a5c3..1225547523e6 100644
--- a/Documentation/devicetree/bindings/mfd/max77686.txt
+++ b/Documentation/devicetree/bindings/mfd/max77686.txt
@@ -8,7 +8,8 @@ client while probing.This document describes the binding for mfd device and
 PMIC submodule.
 
 Binding for the built-in 32k clock generator block is defined separately
-in bindings/clk/maxim,max77686.txt file.
+in the ../clk/maxim,max77686.txt file and binding for the regulators
+is defined in the ../regulator/max77686.txt file.
 
 Required properties:
 - compatible : Must be "maxim,max77686";
@@ -16,36 +17,6 @@ Required properties:
 - interrupts : This i2c device has an IRQ line connected to the main SoC.
 - interrupt-parent : The parent interrupt controller.
 
-Optional node:
-- voltage-regulators : The regulators of max77686 have to be instantiated
-  under subnode named "voltage-regulators" using the following format.
-
-	regulator_name {
-		regulator-compatible = LDOn/BUCKn
-		standard regulator constraints....
-	};
-	refer Documentation/devicetree/bindings/regulator/regulator.txt
-
-  The regulator node's name should be initialized with a string
-to get matched with their hardware counterparts as follow:
-
-	-LDOn 	:	for LDOs, where n can lie in range 1 to 26.
-		 	example: LDO1, LDO2, LDO26.
-	-BUCKn 	:	for BUCKs, where n can lie in range 1 to 9.
-			example: BUCK1, BUCK5, BUCK9.
-
-  Regulators which can be turned off during system suspend:
-	-LDOn	:	2, 6-8, 10-12, 14-16,
-	-BUCKn	:	1-4.
-  Use standard regulator bindings for it ('regulator-off-in-suspend').
-
-  LDO20, LDO21, LDO22, BUCK8 and BUCK9 can be configured to GPIO enable
-  control. To turn this feature on this property must be added to the regulator
-  sub-node:
-	- maxim,ena-gpios :	one GPIO specifier enable control (the gpio
-				flags are actually ignored and always
-				ACTIVE_HIGH is used)
-
 Example:
 
 	max77686: pmic@09 {
@@ -53,27 +24,4 @@ Example:
 		interrupt-parent = <&wakeup_eint>;
 		interrupts = <26 0>;
 		reg = <0x09>;
-
-		voltage-regulators {
-			ldo11_reg: LDO11 {
-				regulator-name = "vdd_ldo11";
-				regulator-min-microvolt = <1900000>;
-				regulator-max-microvolt = <1900000>;
-				regulator-always-on;
-			};
-
-			buck1_reg: BUCK1 {
-				regulator-name = "vdd_mif";
-				regulator-min-microvolt = <950000>;
-				regulator-max-microvolt = <1300000>;
-				regulator-always-on;
-				regulator-boot-on;
-			};
-
-			buck9_reg: BUCK9 {
-				regulator-name = "CAM_ISP_CORE_1.2V";
-				regulator-min-microvolt = <1000000>;
-				regulator-max-microvolt = <1200000>;
-				maxim,ena-gpios = <&gpm0 3 GPIO_ACTIVE_HIGH>;
-			};
-	}
+	};
diff --git a/Documentation/devicetree/bindings/regulator/max77686.txt b/Documentation/devicetree/bindings/regulator/max77686.txt
new file mode 100644
index 000000000000..0dded64d89d3
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/max77686.txt
@@ -0,0 +1,71 @@
+Binding for Maxim MAX77686 regulators
+
+This is a part of the device tree bindings of MAX77686 multi-function device.
+More information can be found in ../mfd/max77686.txt file.
+
+The MAX77686 PMIC has 9 high-efficiency Buck and 26 Low-DropOut (LDO)
+regulators that can be controlled over I2C.
+
+Following properties should be present in main device node of the MFD chip.
+
+Optional node:
+- voltage-regulators : The regulators of max77686 have to be instantiated
+  under subnode named "voltage-regulators" using the following format.
+
+	regulator_name {
+		regulator-compatible = LDOn/BUCKn
+		standard regulator constraints....
+	};
+	refer Documentation/devicetree/bindings/regulator/regulator.txt
+
+  The regulator node's name should be initialized with a string
+to get matched with their hardware counterparts as follow:
+
+	-LDOn 	:	for LDOs, where n can lie in range 1 to 26.
+			example: LDO1, LDO2, LDO26.
+	-BUCKn 	:	for BUCKs, where n can lie in range 1 to 9.
+			example: BUCK1, BUCK5, BUCK9.
+
+  Regulators which can be turned off during system suspend:
+	-LDOn	:	2, 6-8, 10-12, 14-16,
+	-BUCKn	:	1-4.
+  Use standard regulator bindings for it ('regulator-off-in-suspend').
+
+  LDO20, LDO21, LDO22, BUCK8 and BUCK9 can be configured to GPIO enable
+  control. To turn this feature on this property must be added to the regulator
+  sub-node:
+	- maxim,ena-gpios :	one GPIO specifier enable control (the gpio
+				flags are actually ignored and always
+				ACTIVE_HIGH is used)
+
+Example:
+
+	max77686: pmic@09 {
+		compatible = "maxim,max77686";
+		interrupt-parent = <&wakeup_eint>;
+		interrupts = <26 IRQ_TYPE_NONE>;
+		reg = <0x09>;
+
+		voltage-regulators {
+			ldo11_reg: LDO11 {
+				regulator-name = "vdd_ldo11";
+				regulator-min-microvolt = <1900000>;
+				regulator-max-microvolt = <1900000>;
+				regulator-always-on;
+			};
+
+			buck1_reg: BUCK1 {
+				regulator-name = "vdd_mif";
+				regulator-min-microvolt = <950000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck9_reg: BUCK9 {
+				regulator-name = "CAM_ISP_CORE_1.2V";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1200000>;
+				maxim,ena-gpios = <&gpm0 3 GPIO_ACTIVE_HIGH>;
+			};
+	};