diff mbox

[PATCH/RFC,v11,10/20] DT: Add documentation for the mfd Maxim max77693

Message ID 1424276441-3969-11-git-send-email-j.anaszewski@samsung.com
State Superseded, archived
Headers show

Commit Message

Jacek Anaszewski Feb. 18, 2015, 4:20 p.m. UTC 
This patch adds device tree binding documentation for
the flash cell of the Maxim max77693 multifunctional device.

Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
---
 Documentation/devicetree/bindings/mfd/max77693.txt |   61 ++++++++++++++++++++
 1 file changed, 61 insertions(+)
diff mbox

Patch

diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt
index 38e6440..ab8fbd5 100644
--- a/Documentation/devicetree/bindings/mfd/max77693.txt
+++ b/Documentation/devicetree/bindings/mfd/max77693.txt
@@ -76,7 +76,53 @@  Optional properties:
     Valid values: 4300000, 4700000, 4800000, 4900000
     Default: 4300000
 
+- led : the LED submodule device node
+
+There are two LED outputs available - FLED1 and FLED2. Each of them can
+control a separate LED or they can be connected together to double
+the maximum current for a single connected LED. One LED is represented
+by one child node.
+
+Required properties:
+- compatible : Must be "maxim,max77693-led".
+
+Optional properties:
+- maxim,trigger-type : Flash trigger type.
+	Possible trigger types:
+		LEDS_TRIG_TYPE_EDGE (0) - Rising edge of the signal triggers
+			the flash,
+		LEDS_TRIG_TYPE_LEVEL (1) - Strobe pulse length controls duration
+			of the flash.
+- maxim,boost-mode :
+	In boost mode the device can produce up to 1.2A of total current
+	on both outputs. The maximum current on each output is reduced
+	to 625mA then. If not enabled explicitly, boost setting defaults to
+	LEDS_BOOST_FIXED in case both current sources are used.
+	Possible values:
+		LEDS_BOOST_OFF (0) - no boost,
+		LEDS_BOOST_ADAPTIVE (1) - adaptive mode,
+		LEDS_BOOST_FIXED (2) - fixed mode.
+- maxim,boost-mvout : Output voltage of the boost module in millivolts.
+- maxim,mvsys-min : Low input voltage level in millivolts. Flash is not fired
+	if chip estimates that system voltage could drop below this level due
+	to flash power consumption.
+
+Required properties of the LED child node:
+- label : see Documentation/devicetree/bindings/leds/common.txt
+- led-sources : see Documentation/devicetree/bindings/leds/common.txt;
+		device current output identifiers: 0 - FLED1, 1 - FLED2
+
+Optional properties of the LED child node:
+- max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+		Range: 15625 - 250000
+- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+		Range: 15625 - 1000000
+- flash-timeout-us : see Documentation/devicetree/bindings/leds/common.txt
+		Range: 62500 - 1000000
+
 Example:
+#include <dt-bindings/leds/max77693.h>
+
 	max77693@66 {
 		compatible = "maxim,max77693";
 		reg = <0x66>;
@@ -117,5 +163,20 @@  Example:
 			maxim,thermal-regulation-celsius = <75>;
 			maxim,battery-overcurrent-microamp = <3000000>;
 			maxim,charge-input-threshold-microvolt = <4300000>;
+
+		led {
+			compatible = "maxim,max77693-led";
+			maxim,trigger-type = <LEDS_TRIG_TYPE_LEVEL>;
+			maxim,boost-mode = <LEDS_BOOST_FIXED>;
+			maxim,boost-mvout = <5000>;
+			maxim,mvsys-min = <2400>;
+
+			camera_flash: flash-led {
+				label = "max77693-flash1";
+				led-sources = <0>, <1>;
+				max-microamp = <500000>;
+				flash-max-microamp = <1250000>;
+				flash-timeout-us = <1000000>;
+			};
 		};
 	};