[v5,3/5] usb: host: ehci-st: Add ehci-st devicetree bindings documentation

This patch documents the device tree bindings required for the
ehci on-chip controller found in ST consumer electronics SoC's.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
---
 Documentation/devicetree/bindings/usb/ehci-st.txt | 39 +++++++++++++++++++++++
 1 file changed, 39 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/usb/ehci-st.txt

Hello.

On 08/15/2014 06:03 PM, Peter Griffin wrote:

> This patch documents the device tree bindings required for the
> ehci on-chip controller found in ST consumer electronics SoC's.

> Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
> ---
>   Documentation/devicetree/bindings/usb/ehci-st.txt | 39 +++++++++++++++++++++++
>   1 file changed, 39 insertions(+)
>   create mode 100644 Documentation/devicetree/bindings/usb/ehci-st.txt

> diff --git a/Documentation/devicetree/bindings/usb/ehci-st.txt b/Documentation/devicetree/bindings/usb/ehci-st.txt
> new file mode 100644
> index 0000000..fb45fa5
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/usb/ehci-st.txt
> @@ -0,0 +1,39 @@
> +ST USB EHCI controller
> +
> +Required properties:
> + - compatible		: must be "st,st-ehci-300x"
> + - reg			: physical base addresses of the controller and length of memory mapped
> +			  region
> + - interrupts		: one EHCI interrupt should be described here
> + - pinctrl-names	: a pinctrl state named "default" must be defined
> + - pinctrl-0		: phandle referencing pin configuration of the USB controller
> +See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt
> + - clocks		: phandle list of usb clocks
> + - clock-names		: should be "ic" for interconnect clock and "clk48"

    This sentence seems unfinished?

> +See: Documentation/devicetree/bindings/clock/clock-bindings.txt
> +
> + - phys			: phandle for the PHY device
> + - phy-names		: should be "usb"
> + - resets		: phandle + reset specifier pairs to the powerdown and softreset lines
> +			  of the USB IP
> + - reset-names		: should be "power" and "softreset"
> +See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt
> +See: Documentation/devicetree/bindings/reset/reset.txt
> +
> +Example:
> +
> +	ehci1: usb@0xfe203e00 {
> +		compatible = "st,st-ehci-300x";
> +		reg = <0xfe203e00 0x100>;
> +		interrupts = <GIC_SPI 148 IRQ_TYPE_NONE>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_usb1>;
> +		clocks = <&clk_s_a1_ls 0>;

    You said that "clock-names" is a required prop but you didn't specify it.

> +		phys = <&usb2_phy>;
> +		phy-names = "usb";
> +		status = "okay";

    Not necessary.

> +
> +		resets = <&powerdown STIH416_USB1_POWERDOWN>,
> +			 <&softreset STIH416_USB1_SOFTRESET>;
> +		reset-names = "power", "softreset";
> +	};

WBR, Sergei

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html