| Message ID | 1400682454-24535-3-git-send-email-ivan.khoronzhuk@ti.com |
|---|---|
| State | Superseded, archived |
| Headers | show |
On Wednesday 21 May 2014 17:27:31 Ivan Khoronzhuk wrote: > This node is intended to allow SoC reset in case of software reset > or appropriate watchdogs. > > The Keystone SoCs can contain up to 4 watchdog timers to reset > SoC. Each watchdog timer event input is connected to the Reset Mux > block. The Reset Mux block can be configured to cause reset or not. > > Additionally soft or hard reset can be configured. > > Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> > --- > .../bindings/power/reset/keystone-reset.txt | 66 ++++++++++++++++++++++ > 1 file changed, 66 insertions(+) > create mode 100644 Documentation/devicetree/bindings/power/reset/keystone-reset.txt > > diff --git a/Documentation/devicetree/bindings/power/reset/keystone-reset.txt b/Documentation/devicetree/bindings/power/reset/keystone-reset.txt > new file mode 100644 > index 0000000..64cb7b4 > --- /dev/null > +++ b/Documentation/devicetree/bindings/power/reset/keystone-reset.txt > @@ -0,0 +1,66 @@ > +* Device tree bindings for Texas Instruments keystone reset > + > +This node is intended to allow SoC reset in case of software reset > +of selected watchdogs. > + > +The Keystone SoCs can contain up to 4 watchdog timers to reset > +SoC. Each watchdog timer event input is connected to the Reset Mux > +block. The Reset Mux block can be configured to cause reset or not. > + > +Additionally soft or hard reset can be configured. > + > +Required properties: > + > +- compatible: ti,keystone-reset > + > +- ti,syscon-pll: syscon register range used to access pll controller > + registers in order to use reset control registers. > + > +- ti,syscon-dev: syscon register range used to access device state > + control registers in order to use mux block registers > + for all watchdogs. This should be updated to call these phandles rather than register ranges. > +Optional properties: > + > +- ti,soft-reset: Boolean option indicating soft reset. > + By default hard reset is used. > + > +- ti,wdt_list: WDT list that can cause SoC reset. It's not related > + to WDT driver, it's just needed to enable a SoC related > + reset that's triggered by one of WDTs. The list is > + in format: <0>, <2>; It can be in random order and > + begins from 0 to 3, as keystone can contain up to 4 SoC > + reset watchdogs and can be in random order. > + > +Example 1: > +Setup keystone reset so that in case software reset or > +WDT0 is triggered it issues hard reset for SoC. > + > +pllctrl: pll_controller { > + compatible = "syscon"; > + reg = <0x2310000 0x200>; > +}; > + > +devctrl: device_state_control { > + compatible = "syscon"; > + reg = <0x2620000 0x1000>; > +}; It's ok to have these in the example, but please also add a binding file for each one describing what they are, and add a proper "compatible" string so they can be matched by a high-level device driver if needed. This could for instance be compatible = "ti,keystone-1.0-pll-controller", "syscon"; Arnd -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 05/21/2014 05:50 PM, Arnd Bergmann wrote: > On Wednesday 21 May 2014 17:27:31 Ivan Khoronzhuk wrote: >> This node is intended to allow SoC reset in case of software reset >> or appropriate watchdogs. >> >> The Keystone SoCs can contain up to 4 watchdog timers to reset >> SoC. Each watchdog timer event input is connected to the Reset Mux >> block. The Reset Mux block can be configured to cause reset or not. >> >> Additionally soft or hard reset can be configured. >> >> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> >> --- >> .../bindings/power/reset/keystone-reset.txt | 66 ++++++++++++++++++++++ >> 1 file changed, 66 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/power/reset/keystone-reset.txt >> >> diff --git a/Documentation/devicetree/bindings/power/reset/keystone-reset.txt b/Documentation/devicetree/bindings/power/reset/keystone-reset.txt >> new file mode 100644 >> index 0000000..64cb7b4 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/power/reset/keystone-reset.txt >> @@ -0,0 +1,66 @@ >> +* Device tree bindings for Texas Instruments keystone reset >> + >> +This node is intended to allow SoC reset in case of software reset >> +of selected watchdogs. >> + >> +The Keystone SoCs can contain up to 4 watchdog timers to reset >> +SoC. Each watchdog timer event input is connected to the Reset Mux >> +block. The Reset Mux block can be configured to cause reset or not. >> + >> +Additionally soft or hard reset can be configured. >> + >> +Required properties: >> + >> +- compatible: ti,keystone-reset >> + >> +- ti,syscon-pll: syscon register range used to access pll controller >> + registers in order to use reset control registers. >> + >> +- ti,syscon-dev: syscon register range used to access device state >> + control registers in order to use mux block registers >> + for all watchdogs. > This should be updated to call these phandles rather than register ranges. > >> +Optional properties: >> + >> +- ti,soft-reset: Boolean option indicating soft reset. >> + By default hard reset is used. >> + >> +- ti,wdt_list: WDT list that can cause SoC reset. It's not related >> + to WDT driver, it's just needed to enable a SoC related >> + reset that's triggered by one of WDTs. The list is >> + in format: <0>, <2>; It can be in random order and >> + begins from 0 to 3, as keystone can contain up to 4 SoC >> + reset watchdogs and can be in random order. >> + >> +Example 1: >> +Setup keystone reset so that in case software reset or >> +WDT0 is triggered it issues hard reset for SoC. >> + >> +pllctrl: pll_controller { >> + compatible = "syscon"; >> + reg = <0x2310000 0x200>; >> +}; >> + >> +devctrl: device_state_control { >> + compatible = "syscon"; >> + reg = <0x2620000 0x1000>; >> +}; > It's ok to have these in the example, but please also add a binding file > for each one describing what they are, and add a proper "compatible" string > so they can be matched by a high-level device driver if needed. > > This could for instance be > > compatible = "ti,keystone-1.0-pll-controller", "syscon"; Arnd, I've slightly confused where should I add these bindings. The main pll controller mostly used by clk driver.... As its register set is used also by reset driver it's logically to put it to bindings/mfd, but pll controller in mfd it's strange.... Could you please help to decide where should it be?.
On Wednesday 21 May 2014 19:03:38 Ivan Khoronzhuk wrote: > > I've slightly confused where should I add these bindings. > The main pll controller mostly used by clk driver.... > As its register set is used also by reset driver it's logically to put > it to bindings/mfd, > but pll controller in mfd it's strange.... > > Could you please help to decide where should it be?. Put it into Documentation/devicetree/bindings/clock/keystone-pll.txt Arnd -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Wednesday 21 May 2014 12:07 PM, Arnd Bergmann wrote: > On Wednesday 21 May 2014 19:03:38 Ivan Khoronzhuk wrote: >> >> I've slightly confused where should I add these bindings. >> The main pll controller mostly used by clk driver.... >> As its register set is used also by reset driver it's logically to put >> it to bindings/mfd, >> but pll controller in mfd it's strange.... >> >> Could you please help to decide where should it be?. > > Put it into Documentation/devicetree/bindings/clock/keystone-pll.txt > I was just about post the same suggestion. Lets do that. regards, Santosh -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/power/reset/keystone-reset.txt b/Documentation/devicetree/bindings/power/reset/keystone-reset.txt new file mode 100644 index 0000000..64cb7b4 --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/keystone-reset.txt @@ -0,0 +1,66 @@ +* Device tree bindings for Texas Instruments keystone reset + +This node is intended to allow SoC reset in case of software reset +of selected watchdogs. + +The Keystone SoCs can contain up to 4 watchdog timers to reset +SoC. Each watchdog timer event input is connected to the Reset Mux +block. The Reset Mux block can be configured to cause reset or not. + +Additionally soft or hard reset can be configured. + +Required properties: + +- compatible: ti,keystone-reset + +- ti,syscon-pll: syscon register range used to access pll controller + registers in order to use reset control registers. + +- ti,syscon-dev: syscon register range used to access device state + control registers in order to use mux block registers + for all watchdogs. + +Optional properties: + +- ti,soft-reset: Boolean option indicating soft reset. + By default hard reset is used. + +- ti,wdt_list: WDT list that can cause SoC reset. It's not related + to WDT driver, it's just needed to enable a SoC related + reset that's triggered by one of WDTs. The list is + in format: <0>, <2>; It can be in random order and + begins from 0 to 3, as keystone can contain up to 4 SoC + reset watchdogs and can be in random order. + +Example 1: +Setup keystone reset so that in case software reset or +WDT0 is triggered it issues hard reset for SoC. + +pllctrl: pll_controller { + compatible = "syscon"; + reg = <0x2310000 0x200>; +}; + +devctrl: device_state_control { + compatible = "syscon"; + reg = <0x2620000 0x1000>; +}; + +rstctrl: reset-controller { + compatible = "ti,keystone-reset"; + ti,syscon-pll = <&pllctrl>; + ti,syscon-dev = <&devctrl>; + ti,wdt_list = <0>; +}; + +Example 2: +Setup keystone reset so that in case of software reset or +WDT0 or WDT2 is triggered it issues soft reset for SoC. + +rstctrl: reset-controller { + compatible = "ti,keystone-reset"; + ti,syscon-pll = <&pllctrl>; + ti,syscon-dev = <&devctrl>; + ti,wdt_list = <0>, <2>; + ti,soft-reset; +};
This node is intended to allow SoC reset in case of software reset or appropriate watchdogs. The Keystone SoCs can contain up to 4 watchdog timers to reset SoC. Each watchdog timer event input is connected to the Reset Mux block. The Reset Mux block can be configured to cause reset or not. Additionally soft or hard reset can be configured. Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> --- .../bindings/power/reset/keystone-reset.txt | 66 ++++++++++++++++++++++ 1 file changed, 66 insertions(+) create mode 100644 Documentation/devicetree/bindings/power/reset/keystone-reset.txt