@@ -2732,9 +2732,7 @@ N: Suniel Mahesh <sunil@amarulasolutions.com>
F: board/friendlyarm/nanopi-m4
F: board/pine64/rockpro64
F: board/radxa/rockpi-n8
-F: board/radxa/rockpi-n10
F: configs/rock_pi_n8_defconfig
-F: configs/rock_pi_n10_defconfig
F: configs/rockpro64_defconfig
F: package/arm-gnu-toolchain/
deleted file mode 100644
@@ -1,4 +0,0 @@
-label RK3399_ROCK_PI_N10 linux
- kernel /Image
- devicetree /rk3399pro-rock-pi-n10.dtb
- append earlycon=uart8250,mmio32,0xff1a0000 root=/dev/mmcblk0p4 rw rootwait
deleted file mode 100644
@@ -1,39 +0,0 @@
-image boot.vfat {
- vfat {
- files = {
- "Image",
- "rk3399pro-rock-pi-n10.dtb",
- "extlinux"
- }
- }
-
- size = 112M
-}
-
-image sdcard.img {
- hdimage {
- partition-table-type = "gpt"
- }
-
- partition loader1 {
- image = "idbloader.img"
- offset = 32K
- }
-
- partition loader2 {
- image = "u-boot.itb"
- offset = 8M
- }
-
- partition boot {
- partition-type-uuid = F
- bootable = "true"
- image = "boot.vfat"
- offset = 16M
- }
-
- partition rootfs {
- partition-type-uuid = b921b045-1df0-41c3-af44-4c6f280d3fae
- image = "rootfs.ext4"
- }
-}
deleted file mode 100755
@@ -1,5 +0,0 @@
-#!/bin/sh
-
-BOARD_DIR="$(dirname $0)"
-
-install -m 0644 -D $BOARD_DIR/extlinux.conf $BINARIES_DIR/extlinux/extlinux.conf
deleted file mode 100644
@@ -1,61 +0,0 @@
-RADXA ROCKPI-N10
-================
-https://wiki.radxa.com/RockpiN10
-
-Build:
-======
- $ make rock_pi_n10_defconfig
- $ make
-
-Files created in output directory
-=================================
-
-output/images
-.
-├── bl31.elf
-├── boot.vfat
-├── extlinux
-├── idbloader.img
-├── Image
-├── rk3399pro-rock-pi-n10.dtb
-├── rootfs.ext2
-├── rootfs.ext4 -> rootfs.ext2
-├── rootfs.tar
-├── sdcard.img
-├── u-boot.bin
-└── u-boot.itb
-
-Creating bootable SD card:
-==========================
-
-Simply invoke (as root)
-
-sudo dd if=output/images/sdcard.img of=/dev/sdX && sync
-
-Where X is your SD card device.
-
-Booting:
-========
-
-Serial console:
----------------
-RockPi-N10 has a 40-pin GPIO header. The pin layout is as follows:
-
-pin 6: gnd
-pin 8: tx
-pin 10: rx
-
-Baudrate for this board is 1500000.
-
-The boot order on rockpi-n10 is emmc, sd. If emmc contains a valid Image, the board
-always boots from emmc. To boot from SD, erase emmc as per the guide:
-
-https://wiki.amarulasolutions.com/bsp/setup/rockchip/rk3399_emmc.html
-
-Login:
-------
-Enter 'root' as login user, and the prompt is ready.
-
-wiki link:
-----------
-https://wiki.amarulasolutions.com/bsp/rockchip/rk3399pro/rock-pi-n10.html
deleted file mode 100644
@@ -1,55 +0,0 @@
-# Architecture
-BR2_aarch64=y
-BR2_cortex_a72_a53=y
-
-# Linux headers same as kernel, a 5.7 series
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_7=y
-
-# Firmware
-BR2_TARGET_ARM_TRUSTED_FIRMWARE=y
-BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_GIT=y
-BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_REPO_URL="https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git"
-BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_REPO_VERSION="11a0a46a899fcc3b1fdb214b382f3d7495d88eca"
-BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="rk3399"
-BR2_TARGET_ARM_TRUSTED_FIRMWARE_BL31=y
-BR2_TARGET_ARM_TRUSTED_FIRMWARE_NEEDS_ARM32_TOOLCHAIN=y
-BR2_TARGET_ARM_TRUSTED_FIRMWARE_IMAGES=""
-
-# Bootloader
-BR2_TARGET_UBOOT=y
-BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y
-BR2_TARGET_UBOOT_CUSTOM_GIT=y
-BR2_TARGET_UBOOT_CUSTOM_REPO_URL="https://github.com/amarula/u-boot-amarula.git"
-BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="cf2747360fdd1eb0d51dd01a984c7c62c7f714fe"
-BR2_TARGET_UBOOT_BOARD_DEFCONFIG="rock-pi-n10-rk3399pro"
-BR2_TARGET_UBOOT_NEEDS_DTC=y
-BR2_TARGET_UBOOT_NEEDS_PYTHON3=y
-BR2_TARGET_UBOOT_NEEDS_ATF_BL31=y
-BR2_TARGET_UBOOT_NEEDS_ATF_BL31_ELF=y
-BR2_TARGET_UBOOT_FORMAT_CUSTOM=y
-BR2_TARGET_UBOOT_FORMAT_CUSTOM_NAME="u-boot.itb"
-BR2_TARGET_UBOOT_SPL=y
-BR2_TARGET_UBOOT_SPL_NAME="idbloader.img"
-
-# Kernel
-BR2_LINUX_KERNEL=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.7.2"
-BR2_LINUX_KERNEL_USE_ARCH_DEFAULT_CONFIG=y
-BR2_LINUX_KERNEL_DTS_SUPPORT=y
-BR2_LINUX_KERNEL_INTREE_DTS_NAME="rockchip/rk3399pro-rock-pi-n10"
-BR2_LINUX_KERNEL_NEEDS_HOST_OPENSSL=y
-
-# Filesystem
-BR2_TARGET_GENERIC_HOSTNAME="rockpi-n10"
-BR2_TARGET_GENERIC_ISSUE="Welcome to ROCKPI-N10"
-BR2_TARGET_ROOTFS_EXT2=y
-BR2_TARGET_ROOTFS_EXT2_4=y
-BR2_TARGET_ROOTFS_EXT2_SIZE="160M"
-BR2_PACKAGE_HOST_DOSFSTOOLS=y
-BR2_PACKAGE_HOST_GENIMAGE=y
-BR2_PACKAGE_HOST_MTOOLS=y
-BR2_PACKAGE_HOST_UBOOT_TOOLS=y
-BR2_ROOTFS_POST_IMAGE_SCRIPT="support/scripts/genimage.sh"
-BR2_ROOTFS_POST_SCRIPT_ARGS="-c board/radxa/rockpi-n10/genimage.cfg"
-BR2_ROOTFS_POST_BUILD_SCRIPT="board/radxa/rockpi-n10/post-build.sh"
This defconfig has been failing to build for several months, with nobody stepping up to fix it. It's time to drop it. See https://lore.kernel.org/buildroot/20220806224338.0159e15c@windsurf/ for a notification on August 6, 2022 about the issues with this defconfig. Fixes: https://gitlab.com/buildroot.org/buildroot/-/jobs/3259671399 Cc: Suniel Mahesh <sunil@amarulasolutions.com> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> --- DEVELOPERS | 2 - board/radxa/rockpi-n10/extlinux.conf | 4 -- board/radxa/rockpi-n10/genimage.cfg | 39 ------------------ board/radxa/rockpi-n10/post-build.sh | 5 --- board/radxa/rockpi-n10/readme.txt | 61 ---------------------------- configs/rock_pi_n10_defconfig | 55 ------------------------- 6 files changed, 166 deletions(-) delete mode 100644 board/radxa/rockpi-n10/extlinux.conf delete mode 100644 board/radxa/rockpi-n10/genimage.cfg delete mode 100755 board/radxa/rockpi-n10/post-build.sh delete mode 100644 board/radxa/rockpi-n10/readme.txt delete mode 100644 configs/rock_pi_n10_defconfig