@@ -1226,10 +1226,6 @@ F: support/testing/tests/package/test_python_scipy.py
N: Gustavo Heinz <gustavo@gsthnz.com>
F: package/python-m2crypto/
-N: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
-F: configs/arm_juno_defconfig
-F: board/arm/juno/
-
N: Gwenhael Goavec-Merou <gwenhael.goavec-merou@trabucayre.com>
F: board/terasic/de10nano_cyclone5/
F: configs/terasic_de10nano_cyclone5_defconfig
deleted file mode 100644
@@ -1,169 +0,0 @@
-CONFIG_SMP=y
-CONFIG_SYSVIPC=y
-CONFIG_POSIX_MQUEUE=y
-CONFIG_FHANDLE=y
-CONFIG_AUDIT=y
-CONFIG_NO_HZ_IDLE=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_BSD_PROCESS_ACCT=y
-CONFIG_BSD_PROCESS_ACCT_V3=y
-CONFIG_TASKSTATS=y
-CONFIG_TASK_DELAY_ACCT=y
-CONFIG_TASK_XACCT=y
-CONFIG_TASK_IO_ACCOUNTING=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_MEMCG=y
-CONFIG_MEMCG_SWAP=y
-CONFIG_MEMCG_KMEM=y
-CONFIG_CGROUP_HUGETLB=y
-CONFIG_SCHED_AUTOGROUP=y
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_KALLSYMS_ALL=y
-CONFIG_PROFILING=y
-CONFIG_JUMP_LABEL=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_ARCH_VEXPRESS=y
-CONFIG_PCI=y
-CONFIG_PCI_MSI=y
-CONFIG_PCI_HOST_GENERIC=y
-CONFIG_PCIEPORTBUS=y
-CONFIG_HOTPLUG_PCI_PCIE=y
-CONFIG_HOTPLUG_PCI=y
-CONFIG_NR_CPUS=6
-CONFIG_PREEMPT=y
-CONFIG_KSM=y
-CONFIG_TRANSPARENT_HUGEPAGE=y
-CONFIG_CMA=y
-CONFIG_CMDLINE="console=ttyAMA0"
-CONFIG_COMPAT=y
-CONFIG_CPU_IDLE=y
-CONFIG_ARM_CPUIDLE=y
-CONFIG_CPU_FREQ=y
-CONFIG_CPU_FREQ_GOV_USERSPACE=y
-CONFIG_CPU_FREQ_GOV_ONDEMAND=y
-CONFIG_CPU_FREQ_GOV_INTERACTIVE=y
-CONFIG_ARM_BIG_LITTLE_CPUFREQ=y
-CONFIG_ARM_DT_BL_CPUFREQ=y
-CONFIG_ARM_SCPI_CPUFREQ=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-CONFIG_BPF_JIT=y
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_DEVTMPFS=y
-CONFIG_DEVTMPFS_MOUNT=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_SD=y
-CONFIG_ATA=y
-CONFIG_SATA_AHCI=y
-CONFIG_SATA_AHCI_PLATFORM=y
-CONFIG_AHCI_XGENE=y
-CONFIG_PATA_PLATFORM=y
-CONFIG_PATA_OF_PLATFORM=y
-CONFIG_NETDEVICES=y
-CONFIG_TUN=y
-CONFIG_SKY2=y
-CONFIG_SMC91X=y
-CONFIG_SMSC911X=y
-CONFIG_INPUT_EVDEV=y
-CONFIG_SERIO_AMBAKMI=y
-CONFIG_LEGACY_PTY_COUNT=16
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_AMBA_PL011=y
-CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
-CONFIG_SERIAL_OF_PLATFORM=y
-CONFIG_SERIAL_XILINX_PS_UART=y
-CONFIG_SERIAL_XILINX_PS_UART_CONSOLE=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_DESIGNWARE_PLATFORM=y
-CONFIG_I2C_SLAVE=y
-CONFIG_SPI=y
-CONFIG_SPI_PL022=y
-CONFIG_PTP_1588_CLOCK=m
-CONFIG_GPIO_PL061=y
-CONFIG_GPIO_XGENE=y
-CONFIG_POWER_RESET_XGENE=y
-CONFIG_POWER_RESET_SYSCON=y
-CONFIG_REGULATOR=y
-CONFIG_REGULATOR_FIXED_VOLTAGE=y
-CONFIG_REGULATOR_VEXPRESS=m
-CONFIG_DRM=y
-CONFIG_DRM_I2C_NXP_TDA998X=y
-CONFIG_DRM_ARM=y
-CONFIG_DRM_HDLCD=y
-CONFIG_DRM_VIRTUAL_HDLCD=y
-CONFIG_FB_ARMCLCD=y
-CONFIG_LOGO=y
-CONFIG_USB=y
-CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_EHCI_HCD_PLATFORM=y
-CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_OHCI_HCD_PLATFORM=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_ISP1760=y
-CONFIG_NOP_USB_XCEIV=y
-CONFIG_USB_ULPI=y
-CONFIG_MMC=y
-CONFIG_MMC_ARMMMCI=y
-CONFIG_MMC_SDHCI=y
-CONFIG_MMC_SDHCI_PLTFM=y
-CONFIG_MMC_SPI=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_EFI=y
-CONFIG_RTC_DRV_PL030=y
-CONFIG_RTC_DRV_PL031=y
-CONFIG_DMADEVICES=y
-CONFIG_PL330_DMA=y
-CONFIG_COMMON_CLK_SCPI=y
-CONFIG_ARM_TIMER_SP804=y
-CONFIG_MAILBOX=y
-CONFIG_ARM_MHU=y
-CONFIG_PHY_XGENE=y
-CONFIG_ARM_SCPI_PROTOCOL=y
-CONFIG_EXT2_FS=y
-CONFIG_EXT3_FS=y
-CONFIG_FANOTIFY=y
-CONFIG_FANOTIFY_ACCESS_PERMISSIONS=y
-CONFIG_QUOTA=y
-CONFIG_AUTOFS4_FS=y
-CONFIG_FUSE_FS=y
-CONFIG_CUSE=y
-CONFIG_VFAT_FS=y
-CONFIG_TMPFS=y
-CONFIG_HUGETLBFS=y
-CONFIG_EFIVAR_FS=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NLS_ISO8859_1=y
-CONFIG_VIRTUALIZATION=y
-CONFIG_KVM=y
-CONFIG_DYNAMIC_DEBUG=y
-CONFIG_DEBUG_INFO=y
-CONFIG_DEBUG_FS=y
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_KERNEL=y
-CONFIG_LOCKUP_DETECTOR=y
-CONFIG_SECURITY=y
-CONFIG_CRYPTO_ANSI_CPRNG=y
-CONFIG_ARM64_CRYPTO=y
-CONFIG_CRYPTO_SHA1_ARM64_CE=y
-CONFIG_CRYPTO_SHA2_ARM64_CE=y
-CONFIG_CRYPTO_GHASH_ARM64_CE=y
-CONFIG_CRYPTO_AES_ARM64_CE_CCM=y
-CONFIG_CRYPTO_AES_ARM64_CE_BLK=y
-CONFIG_SOUND=y
-CONFIG_SND=y
-CONFIG_SND_SOC=y
-CONFIG_SND_SIMPLE_CARD=y
-CONFIG_SND_DESIGNWARE_I2S=y
-CONFIG_CMA=y
-CONFIG_CMA_SIZE_MBYTES=64
deleted file mode 100644
@@ -1,134 +0,0 @@
-ARM Juno r1/r0
-
-Intro
-=====
-
-These instructions apply to all models of the ARM Juno:
- - Juno r0 (does not support PCIe)
- - Juno r1 (supports PCIe)
- - Juno r2 (Big Cluster with A72)
-
-Buildroot will generate the kernel image, device tree blob, bootloader binaries
-and a minimal root filesystem.
-
-How to build it
-===============
-
-Configure Buildroot
--------------------
-
-Configuring Buildroot is pretty simple, just execute:
-
- $ make arm_juno_defconfig
-
-Build the rootfs, kernel and DTB
---------------------------------
-
-Note: you will need to have access to the network, since Buildroot will
-download the packages' sources.
-
-You may now build your rootfs with:
-
- $ make
-
-(This may take a while)
-
-Result of the build
--------------------
-
-After building, you should obtain this tree:
-
- output/images/
- +-- rootfs.tar
- +-- juno.dtb (if Juno r0 is used)
- +-- juno-r1.dtb (if Juno r1 is used)
- +-- juno-r2.dtb (if Juno r2 is used)
- +-- Image
- +-- bl1.bin
- +-- bl2.bin
- +-- bl2u.bin
- +-- bl31.bin
- +-- fip.bin
- +-- scp-fw.bin
- +-- u-boot.bin
-
-Preparing your rootfs
-======================
-
-Format your pen drive as a ext3 filesystem by executing:
-
- $ mkfs.ext3 /dev/<your device>
-
-Preparing your rootfs
-======================
-
-Format your pen drive as a ext3 filesystem by executing:
-
- $ mkfs.ext3 /dev/<your device>
-
-Installing your rootfs
-======================
-
-After mounting the pen drive please execute the following:
-
- $ sudo tar -xvf output/images/rootfs.tar -C <pen drive mount path>
-
-When completed make sure to unmount the device:
-
- $ umount <pen drive mount path>
-
-Insert the pen drive in one of the ARM Juno' USB type A connectors.
-
-Configure *.dtb in the boot configuration for Juno r0
-=====================================================
-
-SITE1/HBI0262B/images.txt
-.....
-NOR3UPDATE: AUTO ;Image Update:NONE/AUTO/FORCE
-NOR3ADDRESS: 0x00C00000 ;Image Flash Address
-NOR3FILE: \SOFTWARE\juno.dtb ;Image File Name
-NOR3NAME: board.dtb ;Specify Image name to preserve file extension
-NOR3LOAD: 00000000 ;Image Load Address
-NOR3ENTRY: 00000000 ;Image Entry Point
-......
-
-Configure *.dtb in the boot configuration for Juno r1
-=====================================================
-
-SITE1/HBI0262C/images.txt
-......
-NOR3UPDATE: AUTO ;Image Update:NONE/AUTO/FORCE
-NOR3ADDRESS: 0x00C00000 ;Image Flash Address
-NOR3FILE: \SOFTWARE\juno-r1.dtb ;Image File Name
-NOR3NAME: board.dtb ;Specify target filename to preserve file extension
-NOR3LOAD: 00000000 ;Image Load Address
-NOR3ENTRY: 00000000 ;Image Entry Point
-......
-
-Configure *.dtb in the boot configuration for Juno r2
-=====================================================
-
-SITE1/HBI0262D/images.txt
-......
-NOR3UPDATE: AUTO ;Image Update:NONE/AUTO/FORCE
-NOR3ADDRESS: 0x02000000 ;Image Flash Address
-NOR3FILE: \SOFTWARE\juno-r2.dtb ;Image File Name
-NOR3NAME: board.dtb ;Specify target filename to preserve file extension
-NOR3LOAD: 00000000 ;Image Load Address
-NOR3ENTRY: 00000000 ;Image Entry Point
-......
-
-Installing kernel image and DTB
-===============================
-
-1. Connect to the ARM Juno UART0 and execute USB_ON in the terminal
-2. Connect a USB cable between your PC and ARM Juno USB type B connector
- A mass storage device should appear in your desktop.
-3. Open the software/ folder
-4. Copy the 'Image' file to software/
-5. Copy the 'juno-r1.dtb' (r1), 'juno.dtb' (r0) or juno-r2.dtb (r2) file to software/
-6. Copy the bootloader binaries (bl1.bin and fip.bin) to software/
-7. Press the red button in the front pannel of ARM Juno
-
-At this time, the board will erase the Flash entry for each new item and
-replace it with the lastest ones.
deleted file mode 100644
@@ -1,23 +0,0 @@
-BR2_aarch64=y
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_6=y
-BR2_TARGET_GENERIC_HOSTNAME="juno-buildroot"
-BR2_TARGET_GENERIC_ISSUE="Welcome to SNPS Juno by Buildroot"
-BR2_LINUX_KERNEL=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.6"
-BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
-BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/arm/juno/linux-juno-defconfig"
-BR2_LINUX_KERNEL_DTS_SUPPORT=y
-BR2_LINUX_KERNEL_INTREE_DTS_NAME="arm/juno arm/juno-r1 arm/juno-r2"
-BR2_TARGET_ARM_TRUSTED_FIRMWARE=y
-BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_GIT=y
-BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_REPO_URL="https://github.com/ARM-software/arm-trusted-firmware.git"
-BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_REPO_VERSION="v1.4"
-BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="juno"
-BR2_TARGET_ARM_TRUSTED_FIRMWARE_FIP=y
-BR2_TARGET_ARM_TRUSTED_FIRMWARE_UBOOT_AS_BL33=y
-BR2_TARGET_UBOOT=y
-BR2_TARGET_UBOOT_BOARDNAME="vexpress_aemv8a_juno"
-BR2_TARGET_UBOOT_CUSTOM_VERSION=y
-BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2016.03"
-BR2_TARGET_VEXPRESS_FIRMWARE=y
This defconfig has been failing to build for several months, with nobody stepping up to fix it. It's time to drop it. See https://lore.kernel.org/buildroot/20220806224338.0159e15c@windsurf/ for a notification on August 6, 2022 about the issues with this defconfig. Fixes: https://gitlab.com/buildroot.org/buildroot/-/jobs/3234498972 Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> --- DEVELOPERS | 4 - board/arm/juno/linux-juno-defconfig | 169 ---------------------------- board/arm/juno/readme.txt | 134 ---------------------- configs/arm_juno_defconfig | 23 ---- 4 files changed, 330 deletions(-) delete mode 100644 board/arm/juno/linux-juno-defconfig delete mode 100644 board/arm/juno/readme.txt delete mode 100644 configs/arm_juno_defconfig