Message ID | 20180605092745.26198-1-jagan@amarulasolutions.com |
---|---|
State | Changes Requested |
Headers | show |
Series | [v2,1/2] board: amarula: Add A64-Relic support | expand |
Hello, On Tue, 5 Jun 2018 14:57:44 +0530, Jagan Teki wrote: > +label linux-4.17.0-rc3 > + kernel /Image > + devicetree /sun50i-a64-amarula-relic.dtb > + append console=ttyS0,115200 earlyprintk root=/dev/mmcblk1p4 rootwait Is mmcblk1 going to be the SD card or the eMMC ? > +image sdcard.img { So you're producing a sdcard.img, but your readme.txt doesn't use it. > diff --git a/board/amarula/a64-relic/post-build.sh b/board/amarula/a64-relic/post-build.sh > new file mode 100755 > index 0000000000..ec20fca7d9 > --- /dev/null > +++ b/board/amarula/a64-relic/post-build.sh > @@ -0,0 +1,4 @@ > +#!/bin/sh > +BOARD_DIR="$(dirname $0)" > + > +install -m 0644 -D $BOARD_DIR/extlinux.conf $BINARIES_DIR/extlinux/extlinux.conf > diff --git a/board/amarula/a64-relic/readme.txt b/board/amarula/a64-relic/readme.txt > new file mode 100644 > index 0000000000..5d8ae65112 > --- /dev/null > +++ b/board/amarula/a64-relic/readme.txt > @@ -0,0 +1,77 @@ > +Amarula A64 Relic > +================ > + > +Amarula A64-Relic is A64 based IoT device, which support > +- Allwinner A64 Cortex-A53 > +- Mali-400MP2 GPU > +- AXP803 PMIC > +- 1GB DDR3 RAM > +- 8GB eMMC > +- AP6330 Wifi/BLE > +- MIPI-DSI > +- CSI: OV5640 sensor > +- USB OTG > +- 12V DC power supply > + > +Build > +===== > + > + $ make amarula_a64_relic_defconfig > + > + $ make > + > +build files at output/images/: > + - sunxi-spl.bin > + - u-boot.itb > + - Image > + - sun50i-a64-amarula-relic.dtb > + - boot.vfat > + - rootfs.ext4 > + - sdcard.img > + > +Write eMMC > +========= > + > +The board comes with an operating system preloaded on the eMMC. > +To replace it with the Buildroot-built system, take the following > +steps > + > +1. Connect the board UART with host and open minicom(ttyUSBx/115200N8) > + > +2. Supply 12V DC for power-on the board. > + > +3. Interrupt U-Boot by pressing enter > + > +4. Create GPT partitions > + => mmc dev 1 > + => gpt write mmc 1 $partitions > + > +5. Connect the board USB-OTG with USB slot on the host. > + > +6. Initiate fastboot > + => fastboot 0 > + > +7. Write images from host onto eMMC using fastboot > + > + $ output/images > + $ fastboot -i 0x1f3a flash loader1 sunxi-spl.bin > + $ fastboot -i 0x1f3a flash loader2 u-boot.itb > + $ fastboot -i 0x1f3a flash esp boot.vfat > + $ fastboot -i 0x1f3a flash system rootfs.ext4 Is this going to work with the extlinux.conf provided above ? I doubt the same extlinux.conf can work for both the SD card booting and eMMC booting. If you want to support both eMMC and SD card booting, that's OK, but it should be explained in the readme.txt, and it should be clear whether the default extlinux.conf is meant for SD card booting or eMMC booting. > + > +Update eMMC during Development > +============================== > + > +In order to avoid image packing with specified file-system every time > +during development, it better to alter the data in the partition by > +mounting on host with the help of 'ums' in U-Boot. What is "image packing with specified file-system" ? I don't understand what you mean here. Perhaps you wanted to say: "" During development, reflashing the entire filesystem image at every change is time consuming. A useful alternative is to directly access over USB the filesystem stored on the eMMC, using the USB Mass Storage capability of U-Boot. To achieve this: "" Last thing, since your readme.txt says to use fastboot, you should probably enable BR2_PACKAGE_HOST_ANDROID_TOOLS_FASTBOOT, which will make sure fastboot is available in output/host/bin/. And so your readme.txt should point to this fastboot. Best regards, Thomas Petazzoni
On Mon, Jun 18, 2018 at 1:29 AM, Thomas Petazzoni <thomas.petazzoni@bootlin.com> wrote: > Hello, > > On Tue, 5 Jun 2018 14:57:44 +0530, Jagan Teki wrote: > >> +label linux-4.17.0-rc3 >> + kernel /Image >> + devicetree /sun50i-a64-amarula-relic.dtb >> + append console=ttyS0,115200 earlyprintk root=/dev/mmcblk1p4 rootwait > > Is mmcblk1 going to be the SD card or the eMMC ? mmcblk1 is eMMC there is not SD card support on this. mmcblk0 detected as SDIO for wifi > >> +image sdcard.img { > > So you're producing a sdcard.img, but your readme.txt doesn't use it. right now I'm not using this, but with fastboot I'm using individual images. but we can use sdcard.img in eMMC DOS partition if we want. do you want to mentioned the same? > >> diff --git a/board/amarula/a64-relic/post-build.sh b/board/amarula/a64-relic/post-build.sh >> new file mode 100755 >> index 0000000000..ec20fca7d9 >> --- /dev/null >> +++ b/board/amarula/a64-relic/post-build.sh >> @@ -0,0 +1,4 @@ >> +#!/bin/sh >> +BOARD_DIR="$(dirname $0)" >> + >> +install -m 0644 -D $BOARD_DIR/extlinux.conf $BINARIES_DIR/extlinux/extlinux.conf >> diff --git a/board/amarula/a64-relic/readme.txt b/board/amarula/a64-relic/readme.txt >> new file mode 100644 >> index 0000000000..5d8ae65112 >> --- /dev/null >> +++ b/board/amarula/a64-relic/readme.txt >> @@ -0,0 +1,77 @@ >> +Amarula A64 Relic >> +================ >> + >> +Amarula A64-Relic is A64 based IoT device, which support >> +- Allwinner A64 Cortex-A53 >> +- Mali-400MP2 GPU >> +- AXP803 PMIC >> +- 1GB DDR3 RAM >> +- 8GB eMMC >> +- AP6330 Wifi/BLE >> +- MIPI-DSI >> +- CSI: OV5640 sensor >> +- USB OTG >> +- 12V DC power supply >> + >> +Build >> +===== >> + >> + $ make amarula_a64_relic_defconfig >> + >> + $ make >> + >> +build files at output/images/: >> + - sunxi-spl.bin >> + - u-boot.itb >> + - Image >> + - sun50i-a64-amarula-relic.dtb >> + - boot.vfat >> + - rootfs.ext4 >> + - sdcard.img >> + >> +Write eMMC >> +========= >> + >> +The board comes with an operating system preloaded on the eMMC. >> +To replace it with the Buildroot-built system, take the following >> +steps >> + >> +1. Connect the board UART with host and open minicom(ttyUSBx/115200N8) >> + >> +2. Supply 12V DC for power-on the board. >> + >> +3. Interrupt U-Boot by pressing enter >> + >> +4. Create GPT partitions >> + => mmc dev 1 >> + => gpt write mmc 1 $partitions >> + >> +5. Connect the board USB-OTG with USB slot on the host. >> + >> +6. Initiate fastboot >> + => fastboot 0 >> + >> +7. Write images from host onto eMMC using fastboot >> + >> + $ output/images >> + $ fastboot -i 0x1f3a flash loader1 sunxi-spl.bin >> + $ fastboot -i 0x1f3a flash loader2 u-boot.itb >> + $ fastboot -i 0x1f3a flash esp boot.vfat >> + $ fastboot -i 0x1f3a flash system rootfs.ext4 > > Is this going to work with the extlinux.conf provided above ? I doubt > the same extlinux.conf can work for both the SD card booting and eMMC > booting. > > If you want to support both eMMC and SD card booting, that's OK, but it > should be explained in the readme.txt, and it should be clear whether > the default extlinux.conf is meant for SD card booting or eMMC booting. Here, extlinux.conf is for eMMC boot. > >> + >> +Update eMMC during Development >> +============================== >> + >> +In order to avoid image packing with specified file-system every time >> +during development, it better to alter the data in the partition by >> +mounting on host with the help of 'ums' in U-Boot. > > What is "image packing with specified file-system" ? I don't understand > what you mean here. Perhaps you wanted to say: > > "" > > During development, reflashing the entire filesystem image at every > change is time consuming. A useful alternative is to directly access > over USB the filesystem stored on the eMMC, using the USB Mass Storage > capability of U-Boot. To achieve this: > > "" > > Last thing, since your readme.txt says to use fastboot, you should > probably enable BR2_PACKAGE_HOST_ANDROID_TOOLS_FASTBOOT, which will > make sure fastboot is available in output/host/bin/. And so your > readme.txt should point to this fastboot. OK. Jagan.
diff --git a/.gitlab-ci.yml b/.gitlab-ci.yml index e80491cdde..9663105462 100644 --- a/.gitlab-ci.yml +++ b/.gitlab-ci.yml @@ -79,6 +79,7 @@ acmesystems_aria_g25_128mb_defconfig: *defconfig acmesystems_aria_g25_256mb_defconfig: *defconfig acmesystems_arietta_g25_128mb_defconfig: *defconfig acmesystems_arietta_g25_256mb_defconfig: *defconfig +amarula_a64_relic_defconfig: *defconfig amarula_vyasa_rk3288_defconfig: *defconfig arcturus_ucls1012a_defconfig: *defconfig arcturus_ucp1020_defconfig: *defconfig diff --git a/DEVELOPERS b/DEVELOPERS index f24ef2752e..1a893bda9d 100644 --- a/DEVELOPERS +++ b/DEVELOPERS @@ -863,6 +863,7 @@ F: board/amarula/ F: board/asus/ F: board/bananapi/ F: board/engicam/ +F: configs/amarula_a64_relic_defconfig F: configs/amarula_vyasa_rk3288_defconfig F: configs/asus_tinker_rk3288_defconfig F: board/friendlyarm/nanopi-a64/ diff --git a/board/amarula/a64-relic/extlinux.conf b/board/amarula/a64-relic/extlinux.conf new file mode 100644 index 0000000000..9f469846bc --- /dev/null +++ b/board/amarula/a64-relic/extlinux.conf @@ -0,0 +1,4 @@ +label linux-4.17.0-rc3 + kernel /Image + devicetree /sun50i-a64-amarula-relic.dtb + append console=ttyS0,115200 earlyprintk root=/dev/mmcblk1p4 rootwait diff --git a/board/amarula/a64-relic/genimage.cfg b/board/amarula/a64-relic/genimage.cfg new file mode 100644 index 0000000000..871412dee7 --- /dev/null +++ b/board/amarula/a64-relic/genimage.cfg @@ -0,0 +1,39 @@ +image boot.vfat { + vfat { + files = { + "Image", + "sun50i-a64-amarula-relic.dtb", + "extlinux" + } + } + size = 64M +} + +image sdcard.img { + hdimage { + } + + partition spl { + in-partition-table = "no" + image = "sunxi-spl.bin" + offset = 8192 + } + + partition u-boot { + in-partition-table = "no" + image = "u-boot.itb" + offset = 40K + } + + partition boot { + partition-type = 0xC + bootable = "true" + image = "boot.vfat" + offset = 1M + } + + partition rootfs { + partition-type = 0x83 + image = "rootfs.ext4" + } +} diff --git a/board/amarula/a64-relic/post-build.sh b/board/amarula/a64-relic/post-build.sh new file mode 100755 index 0000000000..ec20fca7d9 --- /dev/null +++ b/board/amarula/a64-relic/post-build.sh @@ -0,0 +1,4 @@ +#!/bin/sh +BOARD_DIR="$(dirname $0)" + +install -m 0644 -D $BOARD_DIR/extlinux.conf $BINARIES_DIR/extlinux/extlinux.conf diff --git a/board/amarula/a64-relic/readme.txt b/board/amarula/a64-relic/readme.txt new file mode 100644 index 0000000000..5d8ae65112 --- /dev/null +++ b/board/amarula/a64-relic/readme.txt @@ -0,0 +1,77 @@ +Amarula A64 Relic +================ + +Amarula A64-Relic is A64 based IoT device, which support +- Allwinner A64 Cortex-A53 +- Mali-400MP2 GPU +- AXP803 PMIC +- 1GB DDR3 RAM +- 8GB eMMC +- AP6330 Wifi/BLE +- MIPI-DSI +- CSI: OV5640 sensor +- USB OTG +- 12V DC power supply + +Build +===== + + $ make amarula_a64_relic_defconfig + + $ make + +build files at output/images/: + - sunxi-spl.bin + - u-boot.itb + - Image + - sun50i-a64-amarula-relic.dtb + - boot.vfat + - rootfs.ext4 + - sdcard.img + +Write eMMC +========= + +The board comes with an operating system preloaded on the eMMC. +To replace it with the Buildroot-built system, take the following +steps + +1. Connect the board UART with host and open minicom(ttyUSBx/115200N8) + +2. Supply 12V DC for power-on the board. + +3. Interrupt U-Boot by pressing enter + +4. Create GPT partitions + => mmc dev 1 + => gpt write mmc 1 $partitions + +5. Connect the board USB-OTG with USB slot on the host. + +6. Initiate fastboot + => fastboot 0 + +7. Write images from host onto eMMC using fastboot + + $ output/images + $ fastboot -i 0x1f3a flash loader1 sunxi-spl.bin + $ fastboot -i 0x1f3a flash loader2 u-boot.itb + $ fastboot -i 0x1f3a flash esp boot.vfat + $ fastboot -i 0x1f3a flash system rootfs.ext4 + +Update eMMC during Development +============================== + +In order to avoid image packing with specified file-system every time +during development, it better to alter the data in the partition by +mounting on host with the help of 'ums' in U-Boot. + +1. Build U-Boot with CONFIG_CMD_USB_MASS_STORAGE=y + +2. Follow all 6 steps from 'Write eMMC' and mount eMMC on host + => mmc dev 1 + => ums 0 mmc 1 + +-- +Jagan Teki <jagan@amarulasolutions.com> +05-Jun-2018 diff --git a/configs/amarula_a64_relic_defconfig b/configs/amarula_a64_relic_defconfig new file mode 100644 index 0000000000..44e8e5be13 --- /dev/null +++ b/configs/amarula_a64_relic_defconfig @@ -0,0 +1,46 @@ +BR2_aarch64=y +BR2_cortex_a53=y +BR2_ARM_FPU_VFPV4=y + +# Linux headers same as kernel, a 4.16 series +BR2_KERNEL_HEADERS_4_16=y + +# Firmware +BR2_TARGET_ARM_TRUSTED_FIRMWARE=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_GIT=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_REPO_URL="https://github.com/apritzel/arm-trusted-firmware.git" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="sun50iw1p1" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_REPO_VERSION="aa75c8da415158a94b82a430b2b40000778e851f" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_BL31=y + +# Bootloader +BR2_TARGET_UBOOT=y +BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y +BR2_TARGET_UBOOT_CUSTOM_VERSION=y +BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2018.07-rc1" +BR2_TARGET_UBOOT_BOARD_DEFCONFIG="amarula_a64_relic" +BR2_TARGET_UBOOT_NEEDS_DTC=y +BR2_TARGET_UBOOT_NEEDS_ATF_BL31=y +BR2_TARGET_UBOOT_FORMAT_CUSTOM=y +BR2_TARGET_UBOOT_FORMAT_CUSTOM_NAME="u-boot.itb" +BR2_TARGET_UBOOT_SPL=y +BR2_TARGET_UBOOT_SPL_NAME="spl/sunxi-spl.bin" + +# Kernel +BR2_LINUX_KERNEL=y +BR2_LINUX_KERNEL_CUSTOM_TARBALL=y +BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION="$(call github,amarula,linux-amarula,a64-relic)/linux-amarula_a64-relic.tar.gz" +BR2_LINUX_KERNEL_USE_ARCH_DEFAULT_CONFIG=y +BR2_LINUX_KERNEL_DTS_SUPPORT=y +BR2_LINUX_KERNEL_INTREE_DTS_NAME="allwinner/sun50i-a64-amarula-relic" + +# Filesystem +BR2_TARGET_GENERIC_ISSUE="Welcome to Amarula A64-Relic" +BR2_TARGET_ROOTFS_EXT2=y +BR2_TARGET_ROOTFS_EXT2_4=y +BR2_PACKAGE_HOST_DOSFSTOOLS=y +BR2_PACKAGE_HOST_GENIMAGE=y +BR2_PACKAGE_HOST_MTOOLS=y +BR2_ROOTFS_POST_IMAGE_SCRIPT="support/scripts/genimage.sh" +BR2_ROOTFS_POST_SCRIPT_ARGS="-c board/amarula/a64-relic/genimage.cfg" +BR2_ROOTFS_POST_BUILD_SCRIPT="board/amarula/a64-relic/post-build.sh"
Add initial support for Amarula A64-Relic board with below features: - U-Boot 2018.07-rc1 - Linux 4.17.0-rc6 - Default packages from buildroot Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> --- Changes for v2: - Use mainline U-Boot - Drop uboot.fragment since the UMS used for developement, so note it on readme.txt how to use. - format the 'Write eMMC' steps suggested by Arnout. - fix fastboot steps in readme.txt - add offset in genimage.cfg for boot partition instead of size .gitlab-ci.yml | 1 + DEVELOPERS | 1 + board/amarula/a64-relic/extlinux.conf | 4 ++ board/amarula/a64-relic/genimage.cfg | 39 ++++++++++++++++++ board/amarula/a64-relic/post-build.sh | 4 ++ board/amarula/a64-relic/readme.txt | 77 +++++++++++++++++++++++++++++++++++ configs/amarula_a64_relic_defconfig | 46 +++++++++++++++++++++ 7 files changed, 172 insertions(+) create mode 100644 board/amarula/a64-relic/extlinux.conf create mode 100644 board/amarula/a64-relic/genimage.cfg create mode 100755 board/amarula/a64-relic/post-build.sh create mode 100644 board/amarula/a64-relic/readme.txt create mode 100644 configs/amarula_a64_relic_defconfig