diff mbox series

[v2,09/13] i2c: qup: change completion timeout according to transfer length

Message ID 1520860502-14886-10-git-send-email-absahu@codeaurora.org
State Accepted
Headers show
Series Major code reorganization to make all i2c transfers working | expand

Commit Message

Abhishek Sahu March 12, 2018, 1:14 p.m. UTC 
Currently the completion timeout is being taken according to
maximum transfer length which is too high if SCL is operating in
high frequency. This patch calculates timeout on the basis of
one-byte transfer time and uses the same for completion timeout.

Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
---

* Changes from v1:

1. Added comments to explain TOUT_MIN

 drivers/i2c/busses/i2c-qup.c | 13 ++++++++++---
 1 file changed, 10 insertions(+), 3 deletions(-)
diff mbox series

Patch

diff --git a/drivers/i2c/busses/i2c-qup.c b/drivers/i2c/busses/i2c-qup.c
index bf1b7ee..13c751e 100644
--- a/drivers/i2c/busses/i2c-qup.c
+++ b/drivers/i2c/busses/i2c-qup.c
@@ -121,8 +121,12 @@ 
 #define MX_TX_RX_LEN			SZ_64K
 #define MX_BLOCKS			(MX_TX_RX_LEN / QUP_READ_LIMIT)
 
-/* Max timeout in ms for 32k bytes */
-#define TOUT_MAX			300
+/*
+ * Minimum transfer timeout for i2c transfers in seconds. It will be added on
+ * the top of maximum transfer time calculated from i2c bus speed to compensate
+ * the overheads.
+ */
+#define TOUT_MIN			2
 
 /* Default values. Use these if FW query fails */
 #define DEFAULT_CLK_FREQ 100000
@@ -163,6 +167,7 @@  struct qup_i2c_dev {
 	int			in_blk_sz;
 
 	unsigned long		one_byte_t;
+	unsigned long		xfer_timeout;
 	struct qup_i2c_block	blk;
 
 	struct i2c_msg		*msg;
@@ -849,7 +854,7 @@  static int qup_i2c_bam_do_xfer(struct qup_i2c_dev *qup, struct i2c_msg *msg,
 		dma_async_issue_pending(qup->brx.dma);
 	}
 
-	if (!wait_for_completion_timeout(&qup->xfer, TOUT_MAX * HZ)) {
+	if (!wait_for_completion_timeout(&qup->xfer, qup->xfer_timeout)) {
 		dev_err(qup->dev, "normal trans timed out\n");
 		ret = -ETIMEDOUT;
 	}
@@ -1605,6 +1610,8 @@  static int qup_i2c_probe(struct platform_device *pdev)
 	 */
 	one_bit_t = (USEC_PER_SEC / clk_freq) + 1;
 	qup->one_byte_t = one_bit_t * 9;
+	qup->xfer_timeout = TOUT_MIN * HZ +
+			    usecs_to_jiffies(MX_TX_RX_LEN * qup->one_byte_t);
 
 	dev_dbg(qup->dev, "IN:block:%d, fifo:%d, OUT:block:%d, fifo:%d\n",
 		qup->in_blk_sz, qup->in_fifo_sz,