@@ -264,6 +264,10 @@ ramips_setup_interfaces()
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "5@eth0"
;;
+ wcr-1166ds)
+ ucidef_add_switch "switch0" \
+ "3:lan" "4:wan" "6@eth0"
+ ;;
wcr-150gn)
ucidef_add_switch "switch0" \
"0:lan" "6t@eth0"
@@ -411,6 +415,12 @@ ramips_setup_macs()
lan_mac=$(cat /sys/class/net/eth0/address)
wan_mac=$(macaddr_add "$lan_mac" 5)
;;
+ wcr-1166ds|\
+ wsr-1166)
+ local index="$(find_mtd_index "board_data")"
+ wan_mac="$(grep -m1 mac= "/dev/mtd${index}" | cut -d= -f2)"
+ lan_mac=$wan_mac
+ ;;
wcr-150gn)
wan_mac=$(mtd_get_mac_binary factory 40)
;;
@@ -428,11 +438,6 @@ ramips_setup_macs()
wlr-6000)
wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 32772)" 2)
;;
- wsr-1166)
- local index="$(find_mtd_index "board_data")"
- wan_mac="$(grep -m1 mac= "/dev/mtd${index}" | cut -d= -f2)"
- lan_mac=$wan_mac
- ;;
*)
lan_mac=$(cat /sys/class/net/eth0/address)
wan_mac=$(macaddr_add "$lan_mac" 1)
@@ -220,6 +220,12 @@ get_status_led() {
zbt-wr8305rt)
status_led="$board:green:sys"
;;
+ wcr-1166ds|\
+ whr-300hp2|\
+ wsr-1166|\
+ wsr-600)
+ status_led="$board:green:power"
+ ;;
wcr-150gn|\
wl-351)
status_led="$board:amber:power"
@@ -234,11 +240,6 @@ get_status_led() {
wizfi630a)
status_led="$board::run"
;;
- whr-300hp2|\
- wsr-1166|\
- wsr-600)
- status_led="$board:green:power"
- ;;
wrtnode2r | \
wrtnode2p | \
wrtnode)
@@ -502,6 +502,9 @@ ramips_board_detect() {
*"W502U")
name="w502u"
;;
+ *"WCR-1166DS")
+ name="wcr-1166ds"
+ ;;
*"WCR-150GN")
name="wcr-150gn"
;;
@@ -227,6 +227,11 @@ platform_check_image() {
}
return 0
;;
+ ubnt-erx)
+ nand_do_platform_check "$board" "$1"
+ return $?;
+ ;;
+ wcr-1166ds|\
wsr-1166)
[ "$magic" != "48445230" ] && {
echo "Invalid image type."
@@ -234,10 +239,6 @@ platform_check_image() {
}
return 0
;;
- ubnt-erx)
- nand_do_platform_check "$board" "$1"
- return $?;
- ;;
esac
echo "Sysupgrade is not yet supported on $board."
new file mode 100644
@@ -0,0 +1,172 @@
+/dts-v1/;
+
+#include "mt7628an.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "buffalo,wcr-1166ds", "mediatek,mt7628an-soc";
+ model = "Buffalo WCR-1166DS";
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <20>;
+
+ aoss {
+ label = "aoss";
+ gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+
+ ap {
+ label = "ap";
+ gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_0>;
+ linux,input-type = <EV_SW>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ router_o {
+ label = "wcr-1166ds:orange:router";
+ gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
+ };
+
+ router_g {
+ label = "wcr-1166ds:green:router";
+ gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+ };
+
+ internet_o {
+ label = "wcr-1166ds:orange:internet";
+ gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
+ };
+
+ internet_g {
+ label = "wcr-1166ds:green:internet";
+ gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+ };
+
+ wireless_o {
+ label = "wcr-1166ds:orange:wireless";
+ gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+ };
+
+ wireless_g {
+ label = "wcr-1166ds:green:wireless";
+ gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+ };
+
+ diag {
+ label = "wcr-1166ds:orange:diag";
+ gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
+ };
+
+ power {
+ label = "wcr-1166ds:green:power";
+ gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&ehci {
+ status = "disabled";
+};
+
+&esw {
+ mediatek,portmap = <0x2f>;
+ mediatek,portdisable = <0x27>;
+};
+
+&ohci {
+ status = "disabled";
+};
+
+&pcie {
+ status = "okay";
+ pcie-bridge {
+ mt76@0,0 {
+ reg = <0x0000 0 0 0 0>;
+ device_type = "pci";
+ mediatek,mtd-eeprom = <&factory 0x8000>;
+ mediatek,2ghz = <0>;
+ };
+ };
+};
+
+&pinctrl {
+ state_default: pinctrl0 {
+ gpio {
+ ralink,group = "uart1", "wled_an", "p0led_an", "p1led_an", "p2led_an", "p3led_an", "p4led_an", "wdt", "refclk", "gpio", "i2s";
+ ralink,function = "gpio";
+ };
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ m25p80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <10000000>;
+ m25p,chunked-io = <32>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition@30000 {
+ label = "u-boot-env";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ factory: partition@40000 {
+ label = "factory";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ partition@50000 {
+ label = "firmware";
+ reg = <0x50000 0x7c0000>;
+ };
+
+ partition@810000 {
+ label = "firmware2";
+ reg = <0x810000 0x7c0000>;
+ };
+
+ partition@fd0000 {
+ label = "glbcfg";
+ reg = <0xfd0000 0x10000>;
+ read-only;
+ };
+
+ partition@fe0000 {
+ label = "board_data";
+ reg = <0xfe0000 0x10000>;
+ read-only;
+ };
+ };
+};
+
+&wmac {
+ status = "okay";
+};
@@ -23,6 +23,7 @@ define Image/Build/Initramfs
endef
DEVICE_VARS += DTS IMAGE_SIZE NETGEAR_BOARD_ID NETGEAR_HW_ID
+DEVICE_VARS += BUFFALO_TAG_PLATFORM BUFFALO_TAG_VERSION BUFFALO_TAG_MINOR
loadaddr-y := 0x80000000
loadaddr-$(CONFIG_TARGET_ramips_rt288x) := 0x88000000
@@ -48,7 +49,7 @@ define Build/patch-dtb
endef
define Build/trx
- $(STAGING_DIR_HOST)/bin/trx \
+ $(STAGING_DIR_HOST)/bin/trx $(1) \
-o $@ \
-m $(IMAGE_SIZE) \
-f $(IMAGE_KERNEL) \
@@ -55,3 +55,19 @@ define Device/mac1200r-v2
DEVICE_TITLE := Mercury MAC1200R v2.0
endef
TARGET_DEVICES += mac1200r-v2
+
+define Device/wcr-1166ds
+ DTS := WCR-1166DS
+ BUFFALO_TAG_PLATFORM := MTK
+ BUFFALO_TAG_VERSION := 9.99
+ BUFFALO_TAG_MINOR := 9.99
+ IMAGES += factory.bin
+ IMAGE/sysupgrade.bin := trx | pad-rootfs | append-metadata
+ IMAGE/factory.bin := \
+ trx -M 0x746f435c | pad-rootfs | append-metadata | \
+ buffalo-enc WCR-1166DS $$(BUFFALO_TAG_VERSION) -l | \
+ buffalo-tag-dhp WCR-1166DS JP JP | buffalo-enc-tag -l | \
+ buffalo-dhp-image
+ DEVICE_TITLE := Buffalo WCR-1166DS
+endef
+TARGET_DEVICES += wcr-1166ds
@@ -138,6 +138,7 @@ CONFIG_MTD_NAND_MT7620=y
CONFIG_MTD_PHYSMAP=y
CONFIG_MTD_SPI_NOR=y
CONFIG_MTD_SPLIT_FIRMWARE=y
+CONFIG_MTD_SPLIT_TRX_FW=y
CONFIG_MTD_SPLIT_UIMAGE_FW=y
CONFIG_NEED_DMA_MAP_STATE=y
CONFIG_NEED_PER_CPU_KM=y
new file mode 100644
@@ -0,0 +1,30 @@
+--- a/drivers/mtd/mtdsplit/mtdsplit_trx.c
++++ b/drivers/mtd/mtdsplit/mtdsplit_trx.c
+@@ -13,6 +13,7 @@
+ #include <linux/module.h>
+ #include <linux/init.h>
+ #include <linux/kernel.h>
++#include <linux/of.h>
+ #include <linux/slab.h>
+ #include <linux/mtd/mtd.h>
+ #include <linux/mtd/partitions.h>
+@@ -20,7 +21,8 @@
+
+ #include "mtdsplit.h"
+
+-#define TRX_MAGIC 0x30524448 /* "HDR0" */
++#define TRX_MAGIC 0x30524448 /* "HDR0" */
++#define TRX_MAGIC_BUFFALO 0x746f435c
+
+ struct trx_header {
+ __le32 magic;
+@@ -82,7 +84,8 @@ mtdsplit_parse_trx(struct mtd_info *mast
+ if (ret)
+ continue;
+
+- if (hdr.magic != cpu_to_le32(TRX_MAGIC)) {
++ if (hdr.magic != cpu_to_le32(TRX_MAGIC) &&
++ !(of_machine_is_compatible("buffalo,wcr-1166ds") && hdr.magic == cpu_to_le32(TRX_MAGIC_BUFFALO))) {
+ pr_debug("no valid trx header found in \"%s\" at offset %llx\n",
+ master->name, (unsigned long long) offset);
+ continue;
Buffalo WCR-1166DS is a small wireless router with - MT7628AN + MT7612E - 64MiB DDR2 SDRAM - 16MiB SPI flash - 2T2R 11ac/a/b/g/n Wi-Fi - 2x 10/100M ethernet switch - 8x programmable LED - 3x button - UART pad on PCB (J2: 3.3V, GND, TX, RX) factory image can be installed via stock web UI. due to the "dual image" function in the bootloader, the second half of the SPI flash ("firmware2" partition) cannot be used as a part of the file system. Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com> --- Changes in v4: - rebase and resolve conflict Changes in v3: - added .../linux/ramips/base-files/etc/board.d/02_network | 15 +- target/linux/ramips/base-files/etc/diag.sh | 11 +- target/linux/ramips/base-files/lib/ramips.sh | 3 + .../ramips/base-files/lib/upgrade/platform.sh | 9 +- target/linux/ramips/dts/WCR-1166DS.dts | 172 +++++++++++++++++++++ target/linux/ramips/image/Makefile | 3 +- target/linux/ramips/image/mt7628.mk | 16 ++ target/linux/ramips/mt7628/config-4.4 | 1 + ...r-custom-trx-magic-for-Buffalo-WCR-1166DS.patch | 30 ++++ 9 files changed, 245 insertions(+), 15 deletions(-) create mode 100644 target/linux/ramips/dts/WCR-1166DS.dts create mode 100644 target/linux/ramips/patches-4.4/0400-mtd-mtdsplit-add-support-for-custom-trx-magic-for-Buffalo-WCR-1166DS.patch