diff mbox

[v8,1/3] mfd: lp873x: Add lp873x PMIC support

Message ID 1470977889-27991-2-git-send-email-j-keerthy@ti.com
State New
Headers show

Commit Message

J, KEERTHY Aug. 12, 2016, 4:58 a.m. UTC 
The LP873X chip is a power management IC for Portable Navigation Systems
    and Tablet Computing devices. It contains the following components:

     - Regulators.
     - Configurable General Purpose Output Signals(GPO).

PMIC interacts with the main processor through i2c. PMIC has
couple of LDOs(Linear Regulators), couple of BUCKs (Step-Down DC-DC
Converter Cores) and GPOs(General Purpose Output Signals).

Signed-off-by: Keerthy <j-keerthy@ti.com>
---
 drivers/mfd/Kconfig        |  14 +++
 drivers/mfd/Makefile       |   2 +
 drivers/mfd/lp873x.c       |  97 +++++++++++++++++
 include/linux/mfd/lp873x.h | 264 +++++++++++++++++++++++++++++++++++++++++++++
 4 files changed, 377 insertions(+)
 create mode 100644 drivers/mfd/lp873x.c
 create mode 100644 include/linux/mfd/lp873x.h

Comments

Lee Jones Aug. 31, 2016, 7:56 a.m. UTC | #1 
On Fri, 12 Aug 2016, Keerthy wrote:

> The LP873X chip is a power management IC for Portable Navigation Systems
>     and Tablet Computing devices. It contains the following components:
> 
>      - Regulators.
>      - Configurable General Purpose Output Signals(GPO).

Nit: Better to place a ' ' before the '(' in all cases.

Also below and n the Kconfig.

> PMIC interacts with the main processor through i2c. PMIC has
> couple of LDOs(Linear Regulators), couple of BUCKs (Step-Down DC-DC
> Converter Cores) and GPOs(General Purpose Output Signals).
> 
> Signed-off-by: Keerthy <j-keerthy@ti.com>
> ---
>  drivers/mfd/Kconfig        |  14 +++
>  drivers/mfd/Makefile       |   2 +
>  drivers/mfd/lp873x.c       |  97 +++++++++++++++++
>  include/linux/mfd/lp873x.h | 264 +++++++++++++++++++++++++++++++++++++++++++++
>  4 files changed, 377 insertions(+)
>  create mode 100644 drivers/mfd/lp873x.c
>  create mode 100644 include/linux/mfd/lp873x.h
> 
> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> index 2d1fb64..45fe00a 100644
> --- a/drivers/mfd/Kconfig
> +++ b/drivers/mfd/Kconfig
> @@ -1224,6 +1224,20 @@ config MFD_TPS65217
>  	  This driver can also be built as a module.  If so, the module
>  	  will be called tps65217.
>  
> +config MFD_TI_LP873X
> +	tristate "TI LP873X Power Management IC"
> +	depends on I2C
> +	select MFD_CORE
> +	select REGMAP_I2C
> +	help
> +	  If you say yes here then you get support for the LP873X series of
> +	  Power Management Integrated Circuits(PMIC).
> +	  These include voltage regulators, Thermal protection, Configurable

"thermal"
"configurable"

> +	  General Purpose Outputs(GPO) that are used in portable devices.
> +
> +	  This driver can also be built as a module.  If so, the module
> +	  will be called lp873x.
> +
>  config MFD_TPS65218
>  	tristate "TI TPS65218 Power Management chips"
>  	depends on I2C
> diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
> index 2ba3ba3..42acbcd 100644
> --- a/drivers/mfd/Makefile
> +++ b/drivers/mfd/Makefile
> @@ -22,6 +22,8 @@ obj-$(CONFIG_HTC_EGPIO)		+= htc-egpio.o
>  obj-$(CONFIG_HTC_PASIC3)	+= htc-pasic3.o
>  obj-$(CONFIG_HTC_I2CPLD)	+= htc-i2cpld.o
>  
> +obj-$(CONFIG_MFD_TI_LP873X)	+= lp873x.o
> +
>  obj-$(CONFIG_MFD_DAVINCI_VOICECODEC)	+= davinci_voicecodec.o
>  obj-$(CONFIG_MFD_DM355EVM_MSP)	+= dm355evm_msp.o
>  obj-$(CONFIG_MFD_TI_AM335X_TSCADC)	+= ti_am335x_tscadc.o
> diff --git a/drivers/mfd/lp873x.c b/drivers/mfd/lp873x.c
> new file mode 100644
> index 0000000..3ca0462
> --- /dev/null
> +++ b/drivers/mfd/lp873x.c
> @@ -0,0 +1,97 @@
> +/*
> + * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
> + *
> + * Author: Keerthy <j-keerthy@ti.com>
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation version 2.
> + *
> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
> + * kind, whether express or implied; without even the implied warranty
> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/interrupt.h>
> +#include <linux/mfd/core.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/regmap.h>
> +
> +#include <linux/mfd/lp873x.h>
> +
> +static const struct regmap_config lp873x_regmap_config = {
> +	.reg_bits = 8,
> +	.val_bits = 8,
> +	.max_register = LP873X_REG_MAX,
> +};
> +
> +static const struct mfd_cell lp873x_cells[] = {
> +	{ .name = "lp873x-regulator", },
> +	{ .name = "lp873x-gpio", },
> +};
> +
> +static int lp873x_probe(struct i2c_client *client,
> +			const struct i2c_device_id *ids)
> +{
> +	struct lp873x *lp873;
> +	int ret;
> +	unsigned int otpid;
> +
> +	lp873 = devm_kzalloc(&client->dev, sizeof(*lp873), GFP_KERNEL);
> +	if (!lp873)
> +		return -ENOMEM;
> +
> +	lp873->dev = &client->dev;
> +
> +	lp873->regmap = devm_regmap_init_i2c(client, &lp873x_regmap_config);
> +	if (IS_ERR(lp873->regmap)) {
> +		ret = PTR_ERR(lp873->regmap);
> +		dev_err(lp873->dev,
> +			"Failed to initialize register map: %d\n", ret);
> +		return ret;
> +	}
> +
> +	mutex_init(&lp873->lock);
> +
> +	ret = regmap_read(lp873->regmap, LP873X_REG_OTP_REV, &otpid);
> +	if (ret) {
> +		dev_err(lp873->dev, "Failed to read OTP ID\n");
> +		return ret;
> +	}
> +
> +	lp873->rev = otpid & LP873X_OTP_REV_OTP_ID;

'\n' here.

> +	i2c_set_clientdata(client, lp873);

'\n' here.

> +	ret = mfd_add_devices(lp873->dev, PLATFORM_DEVID_AUTO, lp873x_cells,
> +			      ARRAY_SIZE(lp873x_cells), NULL, 0, NULL);
> +
> +	return ret;
> +}
> +
> +static const struct of_device_id of_lp873x_match_table[] = {
> +	{ .compatible = "ti,lp8733", },
> +	{ .compatible = "ti,lp8732", },
> +	{}
> +};
> +MODULE_DEVICE_TABLE(of, of_lp873x_match_table);
> +
> +static const struct i2c_device_id lp873x_id_table[] = {
> +	{ "lp873x", LP873X },
> +	{ },
> +};
> +MODULE_DEVICE_TABLE(i2c, lp873x_id_table);

Don't set the ID in this table.

> +static struct i2c_driver lp873x_driver = {
> +	.driver		= {

Odd tabbing.

> +		.name	= "lp873x",
> +		.of_match_table = of_lp873x_match_table,
> +	},
> +	.probe		= lp873x_probe,
> +	.id_table	= lp873x_id_table,
> +};
> +module_i2c_driver(lp873x_driver);
> +
> +MODULE_AUTHOR("J Keerthy <j-keerthy@ti.com>");
> +MODULE_DESCRIPTION("LP873X chip family multi-function driver");

"Multi-Function Device driver"

> +MODULE_LICENSE("GPL v2");
> diff --git a/include/linux/mfd/lp873x.h b/include/linux/mfd/lp873x.h
> new file mode 100644
> index 0000000..42bebfa
> --- /dev/null
> +++ b/include/linux/mfd/lp873x.h
> @@ -0,0 +1,264 @@
> +/*
> + * Functions to access LP873X power management chip.
> + *
> + * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation version 2.
> + *
> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
> + * kind, whether express or implied; without even the implied warranty
> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + */
> +
> +#ifndef __LINUX_MFD_LP873X_H
> +#define __LINUX_MFD_LP873X_H
> +
> +#include <linux/i2c.h>
> +#include <linux/regulator/driver.h>
> +#include <linux/regulator/machine.h>
> +
> +/* LP873x chip id list */
> +#define LP873X			0x00
> +
> +/* All register addresses */
> +#define LP873X_REG_DEV_REV		0X00
> +#define LP873X_REG_OTP_REV		0X01
> +#define LP873X_REG_BUCK0_CTRL_1		0X02
> +#define LP873X_REG_BUCK0_CTRL_2		0X03
> +#define LP873X_REG_BUCK1_CTRL_1		0X04
> +#define LP873X_REG_BUCK1_CTRL_2		0X05
> +#define LP873X_REG_BUCK0_VOUT		0X06
> +#define LP873X_REG_BUCK1_VOUT		0X07
> +#define LP873X_REG_LDO0_CTRL		0X08
> +#define LP873X_REG_LDO1_CTRL            0X09
> +#define LP873X_REG_LDO0_VOUT		0X0A
> +#define LP873X_REG_LDO1_VOUT		0X0B
> +#define LP873X_REG_BUCK0_DELAY		0X0C
> +#define LP873X_REG_BUCK1_DELAY		0X0D
> +#define LP873X_REG_LDO0_DELAY		0X0E
> +#define LP873X_REG_LDO1_DELAY		0X0F
> +#define LP873X_REG_GPO_DELAY		0X10
> +#define LP873X_REG_GPO2_DELAY		0X11
> +#define LP873X_REG_GPO_CTRL		0X12
> +#define LP873X_REG_CONFIG		0X13
> +#define LP873X_REG_PLL_CTRL		0X14
> +#define LP873X_REG_PGOOD_CTRL1		0X15
> +#define LP873X_REG_PGOOD_CTRL2		0X16
> +#define LP873X_REG_PG_FAULT		0X17
> +#define LP873X_REG_RESET		0X18
> +#define LP873X_REG_INT_TOP_1		0X19
> +#define LP873X_REG_INT_TOP_2		0X1A
> +#define LP873X_REG_INT_BUCK		0X1B
> +#define LP873X_REG_INT_LDO		0X1C
> +#define LP873X_REG_TOP_STAT		0X1D
> +#define LP873X_REG_BUCK_STAT		0X1E
> +#define LP873X_REG_LDO_STAT		0x1F
> +#define LP873X_REG_TOP_MASK_1		0x20
> +#define LP873X_REG_TOP_MASK_2		0x21
> +#define LP873X_REG_BUCK_MASK		0x22
> +#define LP873X_REG_LDO_MASK		0x23
> +#define LP873X_REG_SEL_I_LOAD		0x24
> +#define LP873X_REG_I_LOAD_2		0x25
> +#define LP873X_REG_I_LOAD_1		0x26
> +
> +#define LP873X_REG_MAX			LP873X_REG_I_LOAD_1
> +
> +/* Register field definitions */
> +#define LP873X_DEV_REV_DEV_ID			0xC0
> +#define LP873X_DEV_REV_ALL_LAYER		0x30
> +#define LP873X_DEV_REV_METAL_LAYER		0x0F
> +
> +#define LP873X_OTP_REV_OTP_ID			0xFF
> +
> +#define LP873X_BUCK0_CTRL_1_BUCK0_FPWM		BIT(3)
> +#define LP873X_BUCK0_CTRL_1_BUCK0_RDIS_EN	BIT(2)
> +#define LP873X_BUCK0_CTRL_1_BUCK0_EN_PIN_CTRL	BIT(1)
> +#define LP873X_BUCK0_CTRL_1_BUCK0_EN		BIT(0)
> +
> +#define LP873X_BUCK0_CTRL_2_BUCK0_ILIM		0x38
> +#define LP873X_BUCK0_CTRL_2_BUCK0_SLEW_RATE	0x07
> +
> +#define LP873X_BUCK1_CTRL_1_BUCK1_FPWM		BIT(3)
> +#define LP873X_BUCK1_CTRL_1_BUCK1_RDIS_EN	BIT(2)
> +#define LP873X_BUCK1_CTRL_1_BUCK1_EN_PIN_CTRL	BIT(1)
> +#define LP873X_BUCK1_CTRL_1_BUCK1_EN		BIT(0)
> +
> +#define LP873X_BUCK1_CTRL_2_BUCK1_ILIM		0x38
> +#define LP873X_BUCK1_CTRL_2_BUCK1_SLEW_RATE	0x07
> +
> +#define LP873X_BUCK0_VOUT_BUCK0_VSET		0xFF
> +
> +#define LP873X_BUCK1_VOUT_BUCK1_VSET		0xFF
> +
> +#define LP873X_LDO0_CTRL_LDO0_RDIS_EN		BIT(2)
> +#define LP873X_LDO0_CTRL_LDO0_EN_PIN_CTRL	BIT(1)
> +#define LP873X_LDO0_CTRL_LDO0_EN		BIT(0)
> +
> +#define LP873X_LDO1_CTRL_LDO1_RDIS_EN		BIT(2)
> +#define LP873X_LDO1_CTRL_LDO1_EN_PIN_CTRL	BIT(1)
> +#define LP873X_LDO1_CTRL_LDO1_EN		BIT(0)
> +
> +#define LP873X_LDO0_VOUT_LDO0_VSET		0x1F
> +
> +#define LP873X_LDO1_VOUT_LDO1_VSET		0x1F
> +
> +#define LP873X_BUCK0_DELAY_BUCK0_SD_DELAY	0xF0
> +#define LP873X_BUCK0_DELAY_BUCK0_SU_DELAY	0x0F
> +
> +#define LP873X_BUCK1_DELAY_BUCK1_SD_DELAY	0xF0
> +#define LP873X_BUCK1_DELAY_BUCK1_SU_DELAY	0x0F
> +
> +#define LP873X_LDO0_DELAY_LDO0_SD_DELAY	0xF0
> +#define LP873X_LDO0_DELAY_LDO0_SU_DELAY	0x0F
> +
> +#define LP873X_LDO1_DELAY_LDO1_SD_DELAY	0xF0
> +#define LP873X_LDO1_DELAY_LDO1_SU_DELAY	0x0F
> +
> +#define LP873X_GPO_DELAY_GPO_SD_DELAY		0xF0
> +#define LP873X_GPO_DELAY_GPO_SU_DELAY		0x0F
> +
> +#define LP873X_GPO2_DELAY_GPO2_SD_DELAY	0xF0
> +#define LP873X_GPO2_DELAY_GPO2_SU_DELAY	0x0F
> +
> +#define LP873X_GPO_CTRL_GPO2_OD		BIT(6)
> +#define LP873X_GPO_CTRL_GPO2_EN_PIN_CTRL	BIT(5)
> +#define LP873X_GPO_CTRL_GPO2_EN		BIT(4)
> +#define LP873X_GPO_CTRL_GPO_OD			BIT(2)
> +#define LP873X_GPO_CTRL_GPO_EN_PIN_CTRL	BIT(1)
> +#define LP873X_GPO_CTRL_GPO_EN			BIT(0)
> +
> +#define LP873X_CONFIG_SU_DELAY_SEL		BIT(6)
> +#define LP873X_CONFIG_SD_DELAY_SEL		BIT(5)
> +#define LP873X_CONFIG_CLKIN_PIN_SEL		BIT(4)
> +#define LP873X_CONFIG_CLKIN_PD			BIT(3)
> +#define LP873X_CONFIG_EN_PD			BIT(2)
> +#define LP873X_CONFIG_TDIE_WARN_LEVEL		BIT(1)
> +#define LP873X_EN_SPREAD_SPEC			BIT(0)
> +
> +#define LP873X_PLL_CTRL_EN_PLL			BIT(6)
> +#define LP873X_EXT_CLK_FREQ			0x1F
> +
> +#define LP873X_PGOOD_CTRL1_PGOOD_POL		BIT(7)
> +#define LP873X_PGOOD_CTRL1_PGOOD_OD		BIT(6)
> +#define LP873X_PGOOD_CTRL1_PGOOD_WINDOW_LDO	BIT(5)
> +#define LP873X_PGOOD_CTRL1_PGOOD_WINDOWN_BUCK	BIT(4)
> +#define LP873X_PGOOD_CTRL1_PGOOD_EN_PGOOD_LDO1	BIT(3)
> +#define LP873X_PGOOD_CTRL1_PGOOD_EN_PGOOD_LDO0	BIT(2)
> +#define LP873X_PGOOD_CTRL1_PGOOD_EN_PGOOD_BUCK1	BIT(1)
> +#define LP873X_PGOOD_CTRL1_PGOOD_EN_PGOOD_BUCK0	BIT(0)
> +
> +#define LP873X_PGOOD_CTRL2_EN_PGOOD_TWARN	BIT(2)
> +#define LP873X_PGOOD_CTRL2_EN_PG_FAULT_GATE	BIT(1)
> +#define LP873X_PGOOD_CTRL2_PGOOD_MODE		BIT(0)
> +
> +#define LP873X_PG_FAULT_PG_FAULT_LDO1		BIT(3)
> +#define LP873X_PG_FAULT_PG_FAULT_LDO0		BIT(2)
> +#define LP873X_PG_FAULT_PG_FAULT_BUCK1		BIT(1)
> +#define LP873X_PG_FAULT_PG_FAULT_BUCK0		BIT(0)
> +
> +#define LP873X_RESET_SW_RESET			BIT(0)
> +
> +#define LP873X_INT_TOP_1_PGOOD_INT		BIT(7)
> +#define LP873X_INT_TOP_1_LDO_INT		BIT(6)
> +#define LP873X_INT_TOP_1_BUCK_INT		BIT(5)
> +#define LP873X_INT_TOP_1_SYNC_CLK_INT		BIT(4)
> +#define LP873X_INT_TOP_1_TDIE_SD_INT		BIT(3)
> +#define LP873X_INT_TOP_1_TDIE_WARN_INT		BIT(2)
> +#define LP873X_INT_TOP_1_OVP_INT		BIT(1)
> +#define LP873X_INT_TOP_1_I_MEAS_INT		BIT(0)
> +
> +#define LP873X_INT_TOP_2_RESET_REG_INT		BIT(0)
> +
> +#define LP873X_INT_BUCK_BUCK1_PG_INT		BIT(6)
> +#define LP873X_INT_BUCK_BUCK1_SC_INT		BIT(5)
> +#define LP873X_INT_BUCK_BUCK1_ILIM_INT		BIT(4)
> +#define LP873X_INT_BUCK_BUCK0_PG_INT		BIT(2)
> +#define LP873X_INT_BUCK_BUCK0_SC_INT		BIT(1)
> +#define LP873X_INT_BUCK_BUCK0_ILIM_INT		BIT(0)
> +
> +#define LP873X_INT_LDO_LDO1_PG_INT		BIT(6)
> +#define LP873X_INT_LDO_LDO1_SC_INT		BIT(5)
> +#define LP873X_INT_LDO_LDO1_ILIM_INT		BIT(4)
> +#define LP873X_INT_LDO_LDO0_PG_INT		BIT(2)
> +#define LP873X_INT_LDO_LDO0_SC_INT		BIT(1)
> +#define LP873X_INT_LDO_LDO0_ILIM_INT		BIT(0)
> +
> +#define LP873X_TOP_STAT_PGOOD_STAT		BIT(7)
> +#define LP873X_TOP_STAT_SYNC_CLK_STAT		BIT(4)
> +#define LP873X_TOP_STAT_TDIE_SD_STAT		BIT(3)
> +#define LP873X_TOP_STAT_TDIE_WARN_STAT		BIT(2)
> +#define LP873X_TOP_STAT_OVP_STAT		BIT(1)
> +
> +#define LP873X_BUCK_STAT_BUCK1_STAT		BIT(7)
> +#define LP873X_BUCK_STAT_BUCK1_PG_STAT		BIT(6)
> +#define LP873X_BUCK_STAT_BUCK1_ILIM_STAT	BIT(4)
> +#define LP873X_BUCK_STAT_BUCK0_STAT		BIT(3)
> +#define LP873X_BUCK_STAT_BUCK0_PG_STAT		BIT(2)
> +#define LP873X_BUCK_STAT_BUCK0_ILIM_STAT	BIT(0)
> +
> +#define LP873X_LDO_STAT_LDO1_STAT		BIT(7)
> +#define LP873X_LDO_STAT_LDO1_PG_STAT		BIT(6)
> +#define LP873X_LDO_STAT_LDO1_ILIM_STAT		BIT(4)
> +#define LP873X_LDO_STAT_LDO0_STAT		BIT(3)
> +#define LP873X_LDO_STAT_LDO0_PG_STAT		BIT(2)
> +#define LP873X_LDO_STAT_LDO0_ILIM_STAT		BIT(0)
> +
> +#define LP873X_TOP_MASK_1_PGOOD_INT_MASK	BIT(7)
> +#define LP873X_TOP_MASK_1_SYNC_CLK_MASK	BIT(4)
> +#define LP873X_TOP_MASK_1_TDIE_WARN_MASK	BIT(2)
> +#define LP873X_TOP_MASK_1_I_MEAS_MASK		BIT(0)
> +
> +#define LP873X_TOP_MASK_2_RESET_REG_MASK	BIT(0)
> +
> +#define LP873X_BUCK_MASK_BUCK1_PGF_MASK	BIT(7)
> +#define LP873X_BUCK_MASK_BUCK1_PGR_MASK	BIT(6)
> +#define LP873X_BUCK_MASK_BUCK1_ILIM_MASK	BIT(4)
> +#define LP873X_BUCK_MASK_BUCK0_PGF_MASK	BIT(3)
> +#define LP873X_BUCK_MASK_BUCK0_PGR_MASK	BIT(2)
> +#define LP873X_BUCK_MASK_BUCK0_ILIM_MASK	BIT(0)
> +
> +#define LP873X_LDO_MASK_LDO1_PGF_MASK		BIT(7)
> +#define LP873X_LDO_MASK_LDO1_PGR_MASK		BIT(6)
> +#define LP873X_LDO_MASK_LDO1_ILIM_MASK		BIT(4)
> +#define LP873X_LDO_MASK_LDO0_PGF_MASK		BIT(3)
> +#define LP873X_LDO_MASK_LDO0_PGR_MASK		BIT(2)
> +#define LP873X_LDO_MASK_LDO0_ILIM_MASK		BIT(0)
> +
> +#define LP873X_SEL_I_LOAD_CURRENT_BUCK_SELECT	BIT(0)
> +
> +#define LP873X_I_LOAD_2_BUCK_LOAD_CURRENT	BIT(0)
> +
> +#define LP873X_I_LOAD_1_BUCK_LOAD_CURRENT	0xFF
> +
> +#define LP873X_MAX_REG_ID		LP873X_LDO_1
> +
> +/* Number of step-down converters available */
> +#define LP873X_NUM_BUCK		2
> +/* Number of LDO voltage regulators available */
> +#define LP873X_NUM_LDO		2
> +/* Number of total regulators available */
> +#define LP873X_NUM_REGULATOR		(LP873X_NUM_BUCK + LP873X_NUM_LDO)
> +
> +enum lp873x_regulator_id {
> +	/* BUCK's */
> +	LP873X_BUCK_0,
> +	LP873X_BUCK_1,
> +	/* LDOs */
> +	LP873X_LDO_0,
> +	LP873X_LDO_1,
> +};
> +
> +/**
> + * struct lp873x - state holder for the lp873x driver
> + * Device data may be used to access the LP873X chip
> + */

Please fill in the reset of the kernel-doc.

One entry per attribute.

> +struct lp873x {
> +	struct device *dev;
> +	u8 rev;
> +	struct mutex lock;	/* lock guarding the data structure */
> +	struct regmap *regmap;
> +};
> +#endif /*  __LINUX_MFD_LP873X_H */

Remove 1 ' '.
Keerthy Aug. 31, 2016, 8:13 a.m. UTC | #2 
On Wednesday 31 August 2016 01:26 PM, Lee Jones wrote:
> On Fri, 12 Aug 2016, Keerthy wrote:
>
>> The LP873X chip is a power management IC for Portable Navigation Systems
>>     and Tablet Computing devices. It contains the following components:
>>
>>      - Regulators.
>>      - Configurable General Purpose Output Signals(GPO).
>
> Nit: Better to place a ' ' before the '(' in all cases.
>
> Also below and n the Kconfig.

Okay.

>
>> PMIC interacts with the main processor through i2c. PMIC has
>> couple of LDOs(Linear Regulators), couple of BUCKs (Step-Down DC-DC
>> Converter Cores) and GPOs(General Purpose Output Signals).
>>
>> Signed-off-by: Keerthy <j-keerthy@ti.com>
>> ---
>>  drivers/mfd/Kconfig        |  14 +++
>>  drivers/mfd/Makefile       |   2 +
>>  drivers/mfd/lp873x.c       |  97 +++++++++++++++++
>>  include/linux/mfd/lp873x.h | 264 +++++++++++++++++++++++++++++++++++++++++++++
>>  4 files changed, 377 insertions(+)
>>  create mode 100644 drivers/mfd/lp873x.c
>>  create mode 100644 include/linux/mfd/lp873x.h
>>
>> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
>> index 2d1fb64..45fe00a 100644
>> --- a/drivers/mfd/Kconfig
>> +++ b/drivers/mfd/Kconfig
>> @@ -1224,6 +1224,20 @@ config MFD_TPS65217
>>  	  This driver can also be built as a module.  If so, the module
>>  	  will be called tps65217.
>>
>> +config MFD_TI_LP873X
>> +	tristate "TI LP873X Power Management IC"
>> +	depends on I2C
>> +	select MFD_CORE
>> +	select REGMAP_I2C
>> +	help
>> +	  If you say yes here then you get support for the LP873X series of
>> +	  Power Management Integrated Circuits(PMIC).
>> +	  These include voltage regulators, Thermal protection, Configurable
>
> "thermal"
> "configurable"

Okay.

>
>> +	  General Purpose Outputs(GPO) that are used in portable devices.
>> +
>> +	  This driver can also be built as a module.  If so, the module
>> +	  will be called lp873x.
>> +
>>  config MFD_TPS65218
>>  	tristate "TI TPS65218 Power Management chips"
>>  	depends on I2C
>> diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
>> index 2ba3ba3..42acbcd 100644
>> --- a/drivers/mfd/Makefile
>> +++ b/drivers/mfd/Makefile
>> @@ -22,6 +22,8 @@ obj-$(CONFIG_HTC_EGPIO)		+= htc-egpio.o
>>  obj-$(CONFIG_HTC_PASIC3)	+= htc-pasic3.o
>>  obj-$(CONFIG_HTC_I2CPLD)	+= htc-i2cpld.o
>>
>> +obj-$(CONFIG_MFD_TI_LP873X)	+= lp873x.o
>> +
>>  obj-$(CONFIG_MFD_DAVINCI_VOICECODEC)	+= davinci_voicecodec.o
>>  obj-$(CONFIG_MFD_DM355EVM_MSP)	+= dm355evm_msp.o
>>  obj-$(CONFIG_MFD_TI_AM335X_TSCADC)	+= ti_am335x_tscadc.o
>> diff --git a/drivers/mfd/lp873x.c b/drivers/mfd/lp873x.c
>> new file mode 100644
>> index 0000000..3ca0462
>> --- /dev/null
>> +++ b/drivers/mfd/lp873x.c
>> @@ -0,0 +1,97 @@
>> +/*
>> + * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
>> + *
>> + * Author: Keerthy <j-keerthy@ti.com>
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation version 2.
>> + *
>> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
>> + * kind, whether express or implied; without even the implied warranty
>> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + * GNU General Public License for more details.
>> + */
>> +
>> +#include <linux/interrupt.h>
>> +#include <linux/mfd/core.h>
>> +#include <linux/module.h>
>> +#include <linux/of_device.h>
>> +#include <linux/regmap.h>
>> +
>> +#include <linux/mfd/lp873x.h>
>> +
>> +static const struct regmap_config lp873x_regmap_config = {
>> +	.reg_bits = 8,
>> +	.val_bits = 8,
>> +	.max_register = LP873X_REG_MAX,
>> +};
>> +
>> +static const struct mfd_cell lp873x_cells[] = {
>> +	{ .name = "lp873x-regulator", },
>> +	{ .name = "lp873x-gpio", },
>> +};
>> +
>> +static int lp873x_probe(struct i2c_client *client,
>> +			const struct i2c_device_id *ids)
>> +{
>> +	struct lp873x *lp873;
>> +	int ret;
>> +	unsigned int otpid;
>> +
>> +	lp873 = devm_kzalloc(&client->dev, sizeof(*lp873), GFP_KERNEL);
>> +	if (!lp873)
>> +		return -ENOMEM;
>> +
>> +	lp873->dev = &client->dev;
>> +
>> +	lp873->regmap = devm_regmap_init_i2c(client, &lp873x_regmap_config);
>> +	if (IS_ERR(lp873->regmap)) {
>> +		ret = PTR_ERR(lp873->regmap);
>> +		dev_err(lp873->dev,
>> +			"Failed to initialize register map: %d\n", ret);
>> +		return ret;
>> +	}
>> +
>> +	mutex_init(&lp873->lock);
>> +
>> +	ret = regmap_read(lp873->regmap, LP873X_REG_OTP_REV, &otpid);
>> +	if (ret) {
>> +		dev_err(lp873->dev, "Failed to read OTP ID\n");
>> +		return ret;
>> +	}
>> +
>> +	lp873->rev = otpid & LP873X_OTP_REV_OTP_ID;
>
> '\n' here.
>
>> +	i2c_set_clientdata(client, lp873);
>
> '\n' here.

Okay.

>
>> +	ret = mfd_add_devices(lp873->dev, PLATFORM_DEVID_AUTO, lp873x_cells,
>> +			      ARRAY_SIZE(lp873x_cells), NULL, 0, NULL);
>> +
>> +	return ret;
>> +}
>> +
>> +static const struct of_device_id of_lp873x_match_table[] = {
>> +	{ .compatible = "ti,lp8733", },
>> +	{ .compatible = "ti,lp8732", },
>> +	{}
>> +};
>> +MODULE_DEVICE_TABLE(of, of_lp873x_match_table);
>> +
>> +static const struct i2c_device_id lp873x_id_table[] = {
>> +	{ "lp873x", LP873X },
>> +	{ },
>> +};
>> +MODULE_DEVICE_TABLE(i2c, lp873x_id_table);
>
> Don't set the ID in this table.

I did not understand this. Could you please elaborate?
You mean no need of LP873X can just be a '0' as i am seeing in other mfd 
drivers?

>
>> +static struct i2c_driver lp873x_driver = {
>> +	.driver		= {
>
> Odd tabbing.

I will correct this.

>
>> +		.name	= "lp873x",
>> +		.of_match_table = of_lp873x_match_table,
>> +	},
>> +	.probe		= lp873x_probe,
>> +	.id_table	= lp873x_id_table,
>> +};
>> +module_i2c_driver(lp873x_driver);
>> +
>> +MODULE_AUTHOR("J Keerthy <j-keerthy@ti.com>");
>> +MODULE_DESCRIPTION("LP873X chip family multi-function driver");
>
> "Multi-Function Device driver"

Okay.

>
>> +MODULE_LICENSE("GPL v2");
>> diff --git a/include/linux/mfd/lp873x.h b/include/linux/mfd/lp873x.h
>> new file mode 100644
>> index 0000000..42bebfa
>> --- /dev/null
>> +++ b/include/linux/mfd/lp873x.h
>> @@ -0,0 +1,264 @@
>> +/*
>> + * Functions to access LP873X power management chip.
>> + *
>> + * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation version 2.
>> + *
>> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
>> + * kind, whether express or implied; without even the implied warranty
>> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + * GNU General Public License for more details.
>> + */
>> +
>> +#ifndef __LINUX_MFD_LP873X_H
>> +#define __LINUX_MFD_LP873X_H
>> +
>> +#include <linux/i2c.h>
>> +#include <linux/regulator/driver.h>
>> +#include <linux/regulator/machine.h>
>> +
>> +/* LP873x chip id list */
>> +#define LP873X			0x00
>> +
>> +/* All register addresses */
>> +#define LP873X_REG_DEV_REV		0X00
>> +#define LP873X_REG_OTP_REV		0X01
>> +#define LP873X_REG_BUCK0_CTRL_1		0X02
>> +#define LP873X_REG_BUCK0_CTRL_2		0X03
>> +#define LP873X_REG_BUCK1_CTRL_1		0X04
>> +#define LP873X_REG_BUCK1_CTRL_2		0X05
>> +#define LP873X_REG_BUCK0_VOUT		0X06
>> +#define LP873X_REG_BUCK1_VOUT		0X07
>> +#define LP873X_REG_LDO0_CTRL		0X08
>> +#define LP873X_REG_LDO1_CTRL            0X09
>> +#define LP873X_REG_LDO0_VOUT		0X0A
>> +#define LP873X_REG_LDO1_VOUT		0X0B
>> +#define LP873X_REG_BUCK0_DELAY		0X0C
>> +#define LP873X_REG_BUCK1_DELAY		0X0D
>> +#define LP873X_REG_LDO0_DELAY		0X0E
>> +#define LP873X_REG_LDO1_DELAY		0X0F
>> +#define LP873X_REG_GPO_DELAY		0X10
>> +#define LP873X_REG_GPO2_DELAY		0X11
>> +#define LP873X_REG_GPO_CTRL		0X12
>> +#define LP873X_REG_CONFIG		0X13
>> +#define LP873X_REG_PLL_CTRL		0X14
>> +#define LP873X_REG_PGOOD_CTRL1		0X15
>> +#define LP873X_REG_PGOOD_CTRL2		0X16
>> +#define LP873X_REG_PG_FAULT		0X17
>> +#define LP873X_REG_RESET		0X18
>> +#define LP873X_REG_INT_TOP_1		0X19
>> +#define LP873X_REG_INT_TOP_2		0X1A
>> +#define LP873X_REG_INT_BUCK		0X1B
>> +#define LP873X_REG_INT_LDO		0X1C
>> +#define LP873X_REG_TOP_STAT		0X1D
>> +#define LP873X_REG_BUCK_STAT		0X1E
>> +#define LP873X_REG_LDO_STAT		0x1F
>> +#define LP873X_REG_TOP_MASK_1		0x20
>> +#define LP873X_REG_TOP_MASK_2		0x21
>> +#define LP873X_REG_BUCK_MASK		0x22
>> +#define LP873X_REG_LDO_MASK		0x23
>> +#define LP873X_REG_SEL_I_LOAD		0x24
>> +#define LP873X_REG_I_LOAD_2		0x25
>> +#define LP873X_REG_I_LOAD_1		0x26
>> +
>> +#define LP873X_REG_MAX			LP873X_REG_I_LOAD_1
>> +
>> +/* Register field definitions */
>> +#define LP873X_DEV_REV_DEV_ID			0xC0
>> +#define LP873X_DEV_REV_ALL_LAYER		0x30
>> +#define LP873X_DEV_REV_METAL_LAYER		0x0F
>> +
>> +#define LP873X_OTP_REV_OTP_ID			0xFF
>> +
>> +#define LP873X_BUCK0_CTRL_1_BUCK0_FPWM		BIT(3)
>> +#define LP873X_BUCK0_CTRL_1_BUCK0_RDIS_EN	BIT(2)
>> +#define LP873X_BUCK0_CTRL_1_BUCK0_EN_PIN_CTRL	BIT(1)
>> +#define LP873X_BUCK0_CTRL_1_BUCK0_EN		BIT(0)
>> +
>> +#define LP873X_BUCK0_CTRL_2_BUCK0_ILIM		0x38
>> +#define LP873X_BUCK0_CTRL_2_BUCK0_SLEW_RATE	0x07
>> +
>> +#define LP873X_BUCK1_CTRL_1_BUCK1_FPWM		BIT(3)
>> +#define LP873X_BUCK1_CTRL_1_BUCK1_RDIS_EN	BIT(2)
>> +#define LP873X_BUCK1_CTRL_1_BUCK1_EN_PIN_CTRL	BIT(1)
>> +#define LP873X_BUCK1_CTRL_1_BUCK1_EN		BIT(0)
>> +
>> +#define LP873X_BUCK1_CTRL_2_BUCK1_ILIM		0x38
>> +#define LP873X_BUCK1_CTRL_2_BUCK1_SLEW_RATE	0x07
>> +
>> +#define LP873X_BUCK0_VOUT_BUCK0_VSET		0xFF
>> +
>> +#define LP873X_BUCK1_VOUT_BUCK1_VSET		0xFF
>> +
>> +#define LP873X_LDO0_CTRL_LDO0_RDIS_EN		BIT(2)
>> +#define LP873X_LDO0_CTRL_LDO0_EN_PIN_CTRL	BIT(1)
>> +#define LP873X_LDO0_CTRL_LDO0_EN		BIT(0)
>> +
>> +#define LP873X_LDO1_CTRL_LDO1_RDIS_EN		BIT(2)
>> +#define LP873X_LDO1_CTRL_LDO1_EN_PIN_CTRL	BIT(1)
>> +#define LP873X_LDO1_CTRL_LDO1_EN		BIT(0)
>> +
>> +#define LP873X_LDO0_VOUT_LDO0_VSET		0x1F
>> +
>> +#define LP873X_LDO1_VOUT_LDO1_VSET		0x1F
>> +
>> +#define LP873X_BUCK0_DELAY_BUCK0_SD_DELAY	0xF0
>> +#define LP873X_BUCK0_DELAY_BUCK0_SU_DELAY	0x0F
>> +
>> +#define LP873X_BUCK1_DELAY_BUCK1_SD_DELAY	0xF0
>> +#define LP873X_BUCK1_DELAY_BUCK1_SU_DELAY	0x0F
>> +
>> +#define LP873X_LDO0_DELAY_LDO0_SD_DELAY	0xF0
>> +#define LP873X_LDO0_DELAY_LDO0_SU_DELAY	0x0F
>> +
>> +#define LP873X_LDO1_DELAY_LDO1_SD_DELAY	0xF0
>> +#define LP873X_LDO1_DELAY_LDO1_SU_DELAY	0x0F
>> +
>> +#define LP873X_GPO_DELAY_GPO_SD_DELAY		0xF0
>> +#define LP873X_GPO_DELAY_GPO_SU_DELAY		0x0F
>> +
>> +#define LP873X_GPO2_DELAY_GPO2_SD_DELAY	0xF0
>> +#define LP873X_GPO2_DELAY_GPO2_SU_DELAY	0x0F
>> +
>> +#define LP873X_GPO_CTRL_GPO2_OD		BIT(6)
>> +#define LP873X_GPO_CTRL_GPO2_EN_PIN_CTRL	BIT(5)
>> +#define LP873X_GPO_CTRL_GPO2_EN		BIT(4)
>> +#define LP873X_GPO_CTRL_GPO_OD			BIT(2)
>> +#define LP873X_GPO_CTRL_GPO_EN_PIN_CTRL	BIT(1)
>> +#define LP873X_GPO_CTRL_GPO_EN			BIT(0)
>> +
>> +#define LP873X_CONFIG_SU_DELAY_SEL		BIT(6)
>> +#define LP873X_CONFIG_SD_DELAY_SEL		BIT(5)
>> +#define LP873X_CONFIG_CLKIN_PIN_SEL		BIT(4)
>> +#define LP873X_CONFIG_CLKIN_PD			BIT(3)
>> +#define LP873X_CONFIG_EN_PD			BIT(2)
>> +#define LP873X_CONFIG_TDIE_WARN_LEVEL		BIT(1)
>> +#define LP873X_EN_SPREAD_SPEC			BIT(0)
>> +
>> +#define LP873X_PLL_CTRL_EN_PLL			BIT(6)
>> +#define LP873X_EXT_CLK_FREQ			0x1F
>> +
>> +#define LP873X_PGOOD_CTRL1_PGOOD_POL		BIT(7)
>> +#define LP873X_PGOOD_CTRL1_PGOOD_OD		BIT(6)
>> +#define LP873X_PGOOD_CTRL1_PGOOD_WINDOW_LDO	BIT(5)
>> +#define LP873X_PGOOD_CTRL1_PGOOD_WINDOWN_BUCK	BIT(4)
>> +#define LP873X_PGOOD_CTRL1_PGOOD_EN_PGOOD_LDO1	BIT(3)
>> +#define LP873X_PGOOD_CTRL1_PGOOD_EN_PGOOD_LDO0	BIT(2)
>> +#define LP873X_PGOOD_CTRL1_PGOOD_EN_PGOOD_BUCK1	BIT(1)
>> +#define LP873X_PGOOD_CTRL1_PGOOD_EN_PGOOD_BUCK0	BIT(0)
>> +
>> +#define LP873X_PGOOD_CTRL2_EN_PGOOD_TWARN	BIT(2)
>> +#define LP873X_PGOOD_CTRL2_EN_PG_FAULT_GATE	BIT(1)
>> +#define LP873X_PGOOD_CTRL2_PGOOD_MODE		BIT(0)
>> +
>> +#define LP873X_PG_FAULT_PG_FAULT_LDO1		BIT(3)
>> +#define LP873X_PG_FAULT_PG_FAULT_LDO0		BIT(2)
>> +#define LP873X_PG_FAULT_PG_FAULT_BUCK1		BIT(1)
>> +#define LP873X_PG_FAULT_PG_FAULT_BUCK0		BIT(0)
>> +
>> +#define LP873X_RESET_SW_RESET			BIT(0)
>> +
>> +#define LP873X_INT_TOP_1_PGOOD_INT		BIT(7)
>> +#define LP873X_INT_TOP_1_LDO_INT		BIT(6)
>> +#define LP873X_INT_TOP_1_BUCK_INT		BIT(5)
>> +#define LP873X_INT_TOP_1_SYNC_CLK_INT		BIT(4)
>> +#define LP873X_INT_TOP_1_TDIE_SD_INT		BIT(3)
>> +#define LP873X_INT_TOP_1_TDIE_WARN_INT		BIT(2)
>> +#define LP873X_INT_TOP_1_OVP_INT		BIT(1)
>> +#define LP873X_INT_TOP_1_I_MEAS_INT		BIT(0)
>> +
>> +#define LP873X_INT_TOP_2_RESET_REG_INT		BIT(0)
>> +
>> +#define LP873X_INT_BUCK_BUCK1_PG_INT		BIT(6)
>> +#define LP873X_INT_BUCK_BUCK1_SC_INT		BIT(5)
>> +#define LP873X_INT_BUCK_BUCK1_ILIM_INT		BIT(4)
>> +#define LP873X_INT_BUCK_BUCK0_PG_INT		BIT(2)
>> +#define LP873X_INT_BUCK_BUCK0_SC_INT		BIT(1)
>> +#define LP873X_INT_BUCK_BUCK0_ILIM_INT		BIT(0)
>> +
>> +#define LP873X_INT_LDO_LDO1_PG_INT		BIT(6)
>> +#define LP873X_INT_LDO_LDO1_SC_INT		BIT(5)
>> +#define LP873X_INT_LDO_LDO1_ILIM_INT		BIT(4)
>> +#define LP873X_INT_LDO_LDO0_PG_INT		BIT(2)
>> +#define LP873X_INT_LDO_LDO0_SC_INT		BIT(1)
>> +#define LP873X_INT_LDO_LDO0_ILIM_INT		BIT(0)
>> +
>> +#define LP873X_TOP_STAT_PGOOD_STAT		BIT(7)
>> +#define LP873X_TOP_STAT_SYNC_CLK_STAT		BIT(4)
>> +#define LP873X_TOP_STAT_TDIE_SD_STAT		BIT(3)
>> +#define LP873X_TOP_STAT_TDIE_WARN_STAT		BIT(2)
>> +#define LP873X_TOP_STAT_OVP_STAT		BIT(1)
>> +
>> +#define LP873X_BUCK_STAT_BUCK1_STAT		BIT(7)
>> +#define LP873X_BUCK_STAT_BUCK1_PG_STAT		BIT(6)
>> +#define LP873X_BUCK_STAT_BUCK1_ILIM_STAT	BIT(4)
>> +#define LP873X_BUCK_STAT_BUCK0_STAT		BIT(3)
>> +#define LP873X_BUCK_STAT_BUCK0_PG_STAT		BIT(2)
>> +#define LP873X_BUCK_STAT_BUCK0_ILIM_STAT	BIT(0)
>> +
>> +#define LP873X_LDO_STAT_LDO1_STAT		BIT(7)
>> +#define LP873X_LDO_STAT_LDO1_PG_STAT		BIT(6)
>> +#define LP873X_LDO_STAT_LDO1_ILIM_STAT		BIT(4)
>> +#define LP873X_LDO_STAT_LDO0_STAT		BIT(3)
>> +#define LP873X_LDO_STAT_LDO0_PG_STAT		BIT(2)
>> +#define LP873X_LDO_STAT_LDO0_ILIM_STAT		BIT(0)
>> +
>> +#define LP873X_TOP_MASK_1_PGOOD_INT_MASK	BIT(7)
>> +#define LP873X_TOP_MASK_1_SYNC_CLK_MASK	BIT(4)
>> +#define LP873X_TOP_MASK_1_TDIE_WARN_MASK	BIT(2)
>> +#define LP873X_TOP_MASK_1_I_MEAS_MASK		BIT(0)
>> +
>> +#define LP873X_TOP_MASK_2_RESET_REG_MASK	BIT(0)
>> +
>> +#define LP873X_BUCK_MASK_BUCK1_PGF_MASK	BIT(7)
>> +#define LP873X_BUCK_MASK_BUCK1_PGR_MASK	BIT(6)
>> +#define LP873X_BUCK_MASK_BUCK1_ILIM_MASK	BIT(4)
>> +#define LP873X_BUCK_MASK_BUCK0_PGF_MASK	BIT(3)
>> +#define LP873X_BUCK_MASK_BUCK0_PGR_MASK	BIT(2)
>> +#define LP873X_BUCK_MASK_BUCK0_ILIM_MASK	BIT(0)
>> +
>> +#define LP873X_LDO_MASK_LDO1_PGF_MASK		BIT(7)
>> +#define LP873X_LDO_MASK_LDO1_PGR_MASK		BIT(6)
>> +#define LP873X_LDO_MASK_LDO1_ILIM_MASK		BIT(4)
>> +#define LP873X_LDO_MASK_LDO0_PGF_MASK		BIT(3)
>> +#define LP873X_LDO_MASK_LDO0_PGR_MASK		BIT(2)
>> +#define LP873X_LDO_MASK_LDO0_ILIM_MASK		BIT(0)
>> +
>> +#define LP873X_SEL_I_LOAD_CURRENT_BUCK_SELECT	BIT(0)
>> +
>> +#define LP873X_I_LOAD_2_BUCK_LOAD_CURRENT	BIT(0)
>> +
>> +#define LP873X_I_LOAD_1_BUCK_LOAD_CURRENT	0xFF
>> +
>> +#define LP873X_MAX_REG_ID		LP873X_LDO_1
>> +
>> +/* Number of step-down converters available */
>> +#define LP873X_NUM_BUCK		2
>> +/* Number of LDO voltage regulators available */
>> +#define LP873X_NUM_LDO		2
>> +/* Number of total regulators available */
>> +#define LP873X_NUM_REGULATOR		(LP873X_NUM_BUCK + LP873X_NUM_LDO)
>> +
>> +enum lp873x_regulator_id {
>> +	/* BUCK's */
>> +	LP873X_BUCK_0,
>> +	LP873X_BUCK_1,
>> +	/* LDOs */
>> +	LP873X_LDO_0,
>> +	LP873X_LDO_1,
>> +};
>> +
>> +/**
>> + * struct lp873x - state holder for the lp873x driver
>> + * Device data may be used to access the LP873X chip
>> + */
>
> Please fill in the reset of the kernel-doc.
>
> One entry per attribute.

Okay.

>
>> +struct lp873x {
>> +	struct device *dev;
>> +	u8 rev;
>> +	struct mutex lock;	/* lock guarding the data structure */
>> +	struct regmap *regmap;
>> +};
>> +#endif /*  __LINUX_MFD_LP873X_H */
>
> Remove 1 ' '.

Okay

>
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Lee Jones Aug. 31, 2016, 11:16 a.m. UTC | #3 
On Wed, 31 Aug 2016, Keerthy wrote:
> On Wednesday 31 August 2016 01:26 PM, Lee Jones wrote:
> > On Fri, 12 Aug 2016, Keerthy wrote:
> > 
> > > The LP873X chip is a power management IC for Portable Navigation Systems
> > >     and Tablet Computing devices. It contains the following components:
> > > 
> > >      - Regulators.
> > >      - Configurable General Purpose Output Signals(GPO).

[...]

> > > +static const struct i2c_device_id lp873x_id_table[] = {
> > > +	{ "lp873x", LP873X },
> > > +	{ },
> > > +};
> > > +MODULE_DEVICE_TABLE(i2c, lp873x_id_table);
> > 
> > Don't set the ID in this table.
> 
> I did not understand this. Could you please elaborate?
> You mean no need of LP873X can just be a '0' as i am seeing in other mfd
> drivers?

Just leave it blank.  No need for the second attribute.
diff mbox

Patch

diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 2d1fb64..45fe00a 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -1224,6 +1224,20 @@  config MFD_TPS65217
 	  This driver can also be built as a module.  If so, the module
 	  will be called tps65217.
 
+config MFD_TI_LP873X
+	tristate "TI LP873X Power Management IC"
+	depends on I2C
+	select MFD_CORE
+	select REGMAP_I2C
+	help
+	  If you say yes here then you get support for the LP873X series of
+	  Power Management Integrated Circuits(PMIC).
+	  These include voltage regulators, Thermal protection, Configurable
+	  General Purpose Outputs(GPO) that are used in portable devices.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called lp873x.
+
 config MFD_TPS65218
 	tristate "TI TPS65218 Power Management chips"
 	depends on I2C
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 2ba3ba3..42acbcd 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -22,6 +22,8 @@  obj-$(CONFIG_HTC_EGPIO)		+= htc-egpio.o
 obj-$(CONFIG_HTC_PASIC3)	+= htc-pasic3.o
 obj-$(CONFIG_HTC_I2CPLD)	+= htc-i2cpld.o
 
+obj-$(CONFIG_MFD_TI_LP873X)	+= lp873x.o
+
 obj-$(CONFIG_MFD_DAVINCI_VOICECODEC)	+= davinci_voicecodec.o
 obj-$(CONFIG_MFD_DM355EVM_MSP)	+= dm355evm_msp.o
 obj-$(CONFIG_MFD_TI_AM335X_TSCADC)	+= ti_am335x_tscadc.o
diff --git a/drivers/mfd/lp873x.c b/drivers/mfd/lp873x.c
new file mode 100644
index 0000000..3ca0462
--- /dev/null
+++ b/drivers/mfd/lp873x.c
@@ -0,0 +1,97 @@ 
+/*
+ * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * Author: Keerthy <j-keerthy@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/interrupt.h>
+#include <linux/mfd/core.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+
+#include <linux/mfd/lp873x.h>
+
+static const struct regmap_config lp873x_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.max_register = LP873X_REG_MAX,
+};
+
+static const struct mfd_cell lp873x_cells[] = {
+	{ .name = "lp873x-regulator", },
+	{ .name = "lp873x-gpio", },
+};
+
+static int lp873x_probe(struct i2c_client *client,
+			const struct i2c_device_id *ids)
+{
+	struct lp873x *lp873;
+	int ret;
+	unsigned int otpid;
+
+	lp873 = devm_kzalloc(&client->dev, sizeof(*lp873), GFP_KERNEL);
+	if (!lp873)
+		return -ENOMEM;
+
+	lp873->dev = &client->dev;
+
+	lp873->regmap = devm_regmap_init_i2c(client, &lp873x_regmap_config);
+	if (IS_ERR(lp873->regmap)) {
+		ret = PTR_ERR(lp873->regmap);
+		dev_err(lp873->dev,
+			"Failed to initialize register map: %d\n", ret);
+		return ret;
+	}
+
+	mutex_init(&lp873->lock);
+
+	ret = regmap_read(lp873->regmap, LP873X_REG_OTP_REV, &otpid);
+	if (ret) {
+		dev_err(lp873->dev, "Failed to read OTP ID\n");
+		return ret;
+	}
+
+	lp873->rev = otpid & LP873X_OTP_REV_OTP_ID;
+	i2c_set_clientdata(client, lp873);
+	ret = mfd_add_devices(lp873->dev, PLATFORM_DEVID_AUTO, lp873x_cells,
+			      ARRAY_SIZE(lp873x_cells), NULL, 0, NULL);
+
+	return ret;
+}
+
+static const struct of_device_id of_lp873x_match_table[] = {
+	{ .compatible = "ti,lp8733", },
+	{ .compatible = "ti,lp8732", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, of_lp873x_match_table);
+
+static const struct i2c_device_id lp873x_id_table[] = {
+	{ "lp873x", LP873X },
+	{ },
+};
+MODULE_DEVICE_TABLE(i2c, lp873x_id_table);
+
+static struct i2c_driver lp873x_driver = {
+	.driver		= {
+		.name	= "lp873x",
+		.of_match_table = of_lp873x_match_table,
+	},
+	.probe		= lp873x_probe,
+	.id_table	= lp873x_id_table,
+};
+module_i2c_driver(lp873x_driver);
+
+MODULE_AUTHOR("J Keerthy <j-keerthy@ti.com>");
+MODULE_DESCRIPTION("LP873X chip family multi-function driver");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/mfd/lp873x.h b/include/linux/mfd/lp873x.h
new file mode 100644
index 0000000..42bebfa
--- /dev/null
+++ b/include/linux/mfd/lp873x.h
@@ -0,0 +1,264 @@ 
+/*
+ * Functions to access LP873X power management chip.
+ *
+ * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __LINUX_MFD_LP873X_H
+#define __LINUX_MFD_LP873X_H
+
+#include <linux/i2c.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+
+/* LP873x chip id list */
+#define LP873X			0x00
+
+/* All register addresses */
+#define LP873X_REG_DEV_REV		0X00
+#define LP873X_REG_OTP_REV		0X01
+#define LP873X_REG_BUCK0_CTRL_1		0X02
+#define LP873X_REG_BUCK0_CTRL_2		0X03
+#define LP873X_REG_BUCK1_CTRL_1		0X04
+#define LP873X_REG_BUCK1_CTRL_2		0X05
+#define LP873X_REG_BUCK0_VOUT		0X06
+#define LP873X_REG_BUCK1_VOUT		0X07
+#define LP873X_REG_LDO0_CTRL		0X08
+#define LP873X_REG_LDO1_CTRL            0X09
+#define LP873X_REG_LDO0_VOUT		0X0A
+#define LP873X_REG_LDO1_VOUT		0X0B
+#define LP873X_REG_BUCK0_DELAY		0X0C
+#define LP873X_REG_BUCK1_DELAY		0X0D
+#define LP873X_REG_LDO0_DELAY		0X0E
+#define LP873X_REG_LDO1_DELAY		0X0F
+#define LP873X_REG_GPO_DELAY		0X10
+#define LP873X_REG_GPO2_DELAY		0X11
+#define LP873X_REG_GPO_CTRL		0X12
+#define LP873X_REG_CONFIG		0X13
+#define LP873X_REG_PLL_CTRL		0X14
+#define LP873X_REG_PGOOD_CTRL1		0X15
+#define LP873X_REG_PGOOD_CTRL2		0X16
+#define LP873X_REG_PG_FAULT		0X17
+#define LP873X_REG_RESET		0X18
+#define LP873X_REG_INT_TOP_1		0X19
+#define LP873X_REG_INT_TOP_2		0X1A
+#define LP873X_REG_INT_BUCK		0X1B
+#define LP873X_REG_INT_LDO		0X1C
+#define LP873X_REG_TOP_STAT		0X1D
+#define LP873X_REG_BUCK_STAT		0X1E
+#define LP873X_REG_LDO_STAT		0x1F
+#define LP873X_REG_TOP_MASK_1		0x20
+#define LP873X_REG_TOP_MASK_2		0x21
+#define LP873X_REG_BUCK_MASK		0x22
+#define LP873X_REG_LDO_MASK		0x23
+#define LP873X_REG_SEL_I_LOAD		0x24
+#define LP873X_REG_I_LOAD_2		0x25
+#define LP873X_REG_I_LOAD_1		0x26
+
+#define LP873X_REG_MAX			LP873X_REG_I_LOAD_1
+
+/* Register field definitions */
+#define LP873X_DEV_REV_DEV_ID			0xC0
+#define LP873X_DEV_REV_ALL_LAYER		0x30
+#define LP873X_DEV_REV_METAL_LAYER		0x0F
+
+#define LP873X_OTP_REV_OTP_ID			0xFF
+
+#define LP873X_BUCK0_CTRL_1_BUCK0_FPWM		BIT(3)
+#define LP873X_BUCK0_CTRL_1_BUCK0_RDIS_EN	BIT(2)
+#define LP873X_BUCK0_CTRL_1_BUCK0_EN_PIN_CTRL	BIT(1)
+#define LP873X_BUCK0_CTRL_1_BUCK0_EN		BIT(0)
+
+#define LP873X_BUCK0_CTRL_2_BUCK0_ILIM		0x38
+#define LP873X_BUCK0_CTRL_2_BUCK0_SLEW_RATE	0x07
+
+#define LP873X_BUCK1_CTRL_1_BUCK1_FPWM		BIT(3)
+#define LP873X_BUCK1_CTRL_1_BUCK1_RDIS_EN	BIT(2)
+#define LP873X_BUCK1_CTRL_1_BUCK1_EN_PIN_CTRL	BIT(1)
+#define LP873X_BUCK1_CTRL_1_BUCK1_EN		BIT(0)
+
+#define LP873X_BUCK1_CTRL_2_BUCK1_ILIM		0x38
+#define LP873X_BUCK1_CTRL_2_BUCK1_SLEW_RATE	0x07
+
+#define LP873X_BUCK0_VOUT_BUCK0_VSET		0xFF
+
+#define LP873X_BUCK1_VOUT_BUCK1_VSET		0xFF
+
+#define LP873X_LDO0_CTRL_LDO0_RDIS_EN		BIT(2)
+#define LP873X_LDO0_CTRL_LDO0_EN_PIN_CTRL	BIT(1)
+#define LP873X_LDO0_CTRL_LDO0_EN		BIT(0)
+
+#define LP873X_LDO1_CTRL_LDO1_RDIS_EN		BIT(2)
+#define LP873X_LDO1_CTRL_LDO1_EN_PIN_CTRL	BIT(1)
+#define LP873X_LDO1_CTRL_LDO1_EN		BIT(0)
+
+#define LP873X_LDO0_VOUT_LDO0_VSET		0x1F
+
+#define LP873X_LDO1_VOUT_LDO1_VSET		0x1F
+
+#define LP873X_BUCK0_DELAY_BUCK0_SD_DELAY	0xF0
+#define LP873X_BUCK0_DELAY_BUCK0_SU_DELAY	0x0F
+
+#define LP873X_BUCK1_DELAY_BUCK1_SD_DELAY	0xF0
+#define LP873X_BUCK1_DELAY_BUCK1_SU_DELAY	0x0F
+
+#define LP873X_LDO0_DELAY_LDO0_SD_DELAY	0xF0
+#define LP873X_LDO0_DELAY_LDO0_SU_DELAY	0x0F
+
+#define LP873X_LDO1_DELAY_LDO1_SD_DELAY	0xF0
+#define LP873X_LDO1_DELAY_LDO1_SU_DELAY	0x0F
+
+#define LP873X_GPO_DELAY_GPO_SD_DELAY		0xF0
+#define LP873X_GPO_DELAY_GPO_SU_DELAY		0x0F
+
+#define LP873X_GPO2_DELAY_GPO2_SD_DELAY	0xF0
+#define LP873X_GPO2_DELAY_GPO2_SU_DELAY	0x0F
+
+#define LP873X_GPO_CTRL_GPO2_OD		BIT(6)
+#define LP873X_GPO_CTRL_GPO2_EN_PIN_CTRL	BIT(5)
+#define LP873X_GPO_CTRL_GPO2_EN		BIT(4)
+#define LP873X_GPO_CTRL_GPO_OD			BIT(2)
+#define LP873X_GPO_CTRL_GPO_EN_PIN_CTRL	BIT(1)
+#define LP873X_GPO_CTRL_GPO_EN			BIT(0)
+
+#define LP873X_CONFIG_SU_DELAY_SEL		BIT(6)
+#define LP873X_CONFIG_SD_DELAY_SEL		BIT(5)
+#define LP873X_CONFIG_CLKIN_PIN_SEL		BIT(4)
+#define LP873X_CONFIG_CLKIN_PD			BIT(3)
+#define LP873X_CONFIG_EN_PD			BIT(2)
+#define LP873X_CONFIG_TDIE_WARN_LEVEL		BIT(1)
+#define LP873X_EN_SPREAD_SPEC			BIT(0)
+
+#define LP873X_PLL_CTRL_EN_PLL			BIT(6)
+#define LP873X_EXT_CLK_FREQ			0x1F
+
+#define LP873X_PGOOD_CTRL1_PGOOD_POL		BIT(7)
+#define LP873X_PGOOD_CTRL1_PGOOD_OD		BIT(6)
+#define LP873X_PGOOD_CTRL1_PGOOD_WINDOW_LDO	BIT(5)
+#define LP873X_PGOOD_CTRL1_PGOOD_WINDOWN_BUCK	BIT(4)
+#define LP873X_PGOOD_CTRL1_PGOOD_EN_PGOOD_LDO1	BIT(3)
+#define LP873X_PGOOD_CTRL1_PGOOD_EN_PGOOD_LDO0	BIT(2)
+#define LP873X_PGOOD_CTRL1_PGOOD_EN_PGOOD_BUCK1	BIT(1)
+#define LP873X_PGOOD_CTRL1_PGOOD_EN_PGOOD_BUCK0	BIT(0)
+
+#define LP873X_PGOOD_CTRL2_EN_PGOOD_TWARN	BIT(2)
+#define LP873X_PGOOD_CTRL2_EN_PG_FAULT_GATE	BIT(1)
+#define LP873X_PGOOD_CTRL2_PGOOD_MODE		BIT(0)
+
+#define LP873X_PG_FAULT_PG_FAULT_LDO1		BIT(3)
+#define LP873X_PG_FAULT_PG_FAULT_LDO0		BIT(2)
+#define LP873X_PG_FAULT_PG_FAULT_BUCK1		BIT(1)
+#define LP873X_PG_FAULT_PG_FAULT_BUCK0		BIT(0)
+
+#define LP873X_RESET_SW_RESET			BIT(0)
+
+#define LP873X_INT_TOP_1_PGOOD_INT		BIT(7)
+#define LP873X_INT_TOP_1_LDO_INT		BIT(6)
+#define LP873X_INT_TOP_1_BUCK_INT		BIT(5)
+#define LP873X_INT_TOP_1_SYNC_CLK_INT		BIT(4)
+#define LP873X_INT_TOP_1_TDIE_SD_INT		BIT(3)
+#define LP873X_INT_TOP_1_TDIE_WARN_INT		BIT(2)
+#define LP873X_INT_TOP_1_OVP_INT		BIT(1)
+#define LP873X_INT_TOP_1_I_MEAS_INT		BIT(0)
+
+#define LP873X_INT_TOP_2_RESET_REG_INT		BIT(0)
+
+#define LP873X_INT_BUCK_BUCK1_PG_INT		BIT(6)
+#define LP873X_INT_BUCK_BUCK1_SC_INT		BIT(5)
+#define LP873X_INT_BUCK_BUCK1_ILIM_INT		BIT(4)
+#define LP873X_INT_BUCK_BUCK0_PG_INT		BIT(2)
+#define LP873X_INT_BUCK_BUCK0_SC_INT		BIT(1)
+#define LP873X_INT_BUCK_BUCK0_ILIM_INT		BIT(0)
+
+#define LP873X_INT_LDO_LDO1_PG_INT		BIT(6)
+#define LP873X_INT_LDO_LDO1_SC_INT		BIT(5)
+#define LP873X_INT_LDO_LDO1_ILIM_INT		BIT(4)
+#define LP873X_INT_LDO_LDO0_PG_INT		BIT(2)
+#define LP873X_INT_LDO_LDO0_SC_INT		BIT(1)
+#define LP873X_INT_LDO_LDO0_ILIM_INT		BIT(0)
+
+#define LP873X_TOP_STAT_PGOOD_STAT		BIT(7)
+#define LP873X_TOP_STAT_SYNC_CLK_STAT		BIT(4)
+#define LP873X_TOP_STAT_TDIE_SD_STAT		BIT(3)
+#define LP873X_TOP_STAT_TDIE_WARN_STAT		BIT(2)
+#define LP873X_TOP_STAT_OVP_STAT		BIT(1)
+
+#define LP873X_BUCK_STAT_BUCK1_STAT		BIT(7)
+#define LP873X_BUCK_STAT_BUCK1_PG_STAT		BIT(6)
+#define LP873X_BUCK_STAT_BUCK1_ILIM_STAT	BIT(4)
+#define LP873X_BUCK_STAT_BUCK0_STAT		BIT(3)
+#define LP873X_BUCK_STAT_BUCK0_PG_STAT		BIT(2)
+#define LP873X_BUCK_STAT_BUCK0_ILIM_STAT	BIT(0)
+
+#define LP873X_LDO_STAT_LDO1_STAT		BIT(7)
+#define LP873X_LDO_STAT_LDO1_PG_STAT		BIT(6)
+#define LP873X_LDO_STAT_LDO1_ILIM_STAT		BIT(4)
+#define LP873X_LDO_STAT_LDO0_STAT		BIT(3)
+#define LP873X_LDO_STAT_LDO0_PG_STAT		BIT(2)
+#define LP873X_LDO_STAT_LDO0_ILIM_STAT		BIT(0)
+
+#define LP873X_TOP_MASK_1_PGOOD_INT_MASK	BIT(7)
+#define LP873X_TOP_MASK_1_SYNC_CLK_MASK	BIT(4)
+#define LP873X_TOP_MASK_1_TDIE_WARN_MASK	BIT(2)
+#define LP873X_TOP_MASK_1_I_MEAS_MASK		BIT(0)
+
+#define LP873X_TOP_MASK_2_RESET_REG_MASK	BIT(0)
+
+#define LP873X_BUCK_MASK_BUCK1_PGF_MASK	BIT(7)
+#define LP873X_BUCK_MASK_BUCK1_PGR_MASK	BIT(6)
+#define LP873X_BUCK_MASK_BUCK1_ILIM_MASK	BIT(4)
+#define LP873X_BUCK_MASK_BUCK0_PGF_MASK	BIT(3)
+#define LP873X_BUCK_MASK_BUCK0_PGR_MASK	BIT(2)
+#define LP873X_BUCK_MASK_BUCK0_ILIM_MASK	BIT(0)
+
+#define LP873X_LDO_MASK_LDO1_PGF_MASK		BIT(7)
+#define LP873X_LDO_MASK_LDO1_PGR_MASK		BIT(6)
+#define LP873X_LDO_MASK_LDO1_ILIM_MASK		BIT(4)
+#define LP873X_LDO_MASK_LDO0_PGF_MASK		BIT(3)
+#define LP873X_LDO_MASK_LDO0_PGR_MASK		BIT(2)
+#define LP873X_LDO_MASK_LDO0_ILIM_MASK		BIT(0)
+
+#define LP873X_SEL_I_LOAD_CURRENT_BUCK_SELECT	BIT(0)
+
+#define LP873X_I_LOAD_2_BUCK_LOAD_CURRENT	BIT(0)
+
+#define LP873X_I_LOAD_1_BUCK_LOAD_CURRENT	0xFF
+
+#define LP873X_MAX_REG_ID		LP873X_LDO_1
+
+/* Number of step-down converters available */
+#define LP873X_NUM_BUCK		2
+/* Number of LDO voltage regulators available */
+#define LP873X_NUM_LDO		2
+/* Number of total regulators available */
+#define LP873X_NUM_REGULATOR		(LP873X_NUM_BUCK + LP873X_NUM_LDO)
+
+enum lp873x_regulator_id {
+	/* BUCK's */
+	LP873X_BUCK_0,
+	LP873X_BUCK_1,
+	/* LDOs */
+	LP873X_LDO_0,
+	LP873X_LDO_1,
+};
+
+/**
+ * struct lp873x - state holder for the lp873x driver
+ * Device data may be used to access the LP873X chip
+ */
+struct lp873x {
+	struct device *dev;
+	u8 rev;
+	struct mutex lock;	/* lock guarding the data structure */
+	struct regmap *regmap;
+};
+#endif /*  __LINUX_MFD_LP873X_H */