| Message ID | 20210203165233.22177-1-jbx6244@gmail.com |
|---|---|
| State | Superseded, archived |
| Headers | show |
| Series | [v2,1/7] dt-bindings: usb: convert rockchip,dwc3.txt to yaml | expand |
| Context | Check | Description |
|---|---|---|
| robh/checkpatch | warning | total: 0 errors, 3 warnings, 103 lines checked |
| robh/dt-meta-schema | fail | build log |
Hi Rob, Heiko, Version 2 without node wrapper. Is that OK for backwards compatibility? New SoC rk3568 and rk3566 in the manufacturer tree also seem to use dwc3 usb, so now only a rk3399 node restyle in mainline with conversion to yaml. On 2/3/21 5:52 PM, Johan Jonker wrote: > In the past Rockchip dwc3 usb nodes were manually checked. > With the conversion of snps,dwc3.yaml as common document > we now can convert rockchip,dwc3.txt to yaml as well. > Remove node wrapper. > > Added properties for rk3399 are: > power-domains > resets > reset-names > > Signed-off-by: Johan Jonker <jbx6244@gmail.com> > --- > .../devicetree/bindings/usb/rockchip,dwc3.txt | 56 ----------- > .../devicetree/bindings/usb/rockchip,dwc3.yaml | 103 +++++++++++++++++++++ > 2 files changed, 103 insertions(+), 56 deletions(-) > delete mode 100644 Documentation/devicetree/bindings/usb/rockchip,dwc3.txt > create mode 100644 Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml > > diff --git a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt > deleted file mode 100644 > index 945204932..000000000 > --- a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt > +++ /dev/null > @@ -1,56 +0,0 @@ > -Rockchip SuperSpeed DWC3 USB SoC controller > - > -Required properties: > -- compatible: should contain "rockchip,rk3399-dwc3" for rk3399 SoC > -- clocks: A list of phandle + clock-specifier pairs for the > - clocks listed in clock-names > -- clock-names: Should contain the following: > - "ref_clk" Controller reference clk, have to be 24 MHz > - "suspend_clk" Controller suspend clk, have to be 24 MHz or 32 KHz > - "bus_clk" Master/Core clock, have to be >= 62.5 MHz for SS > - operation and >= 30MHz for HS operation > - "grf_clk" Controller grf clk > - > -Required child node: > -A child node must exist to represent the core DWC3 IP block. The name of > -the node is not important. The content of the node is defined in dwc3.txt. > - > -Phy documentation is provided in the following places: > -Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.yaml - USB2.0 PHY > -Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt - Type-C PHY > - > -Example device nodes: > - > - usbdrd3_0: usb@fe800000 { > - compatible = "rockchip,rk3399-dwc3"; > - clocks = <&cru SCLK_USB3OTG0_REF>, <&cru SCLK_USB3OTG0_SUSPEND>, > - <&cru ACLK_USB3OTG0>, <&cru ACLK_USB3_GRF>; > - clock-names = "ref_clk", "suspend_clk", > - "bus_clk", "grf_clk"; > - #address-cells = <2>; > - #size-cells = <2>; > - ranges; > - usbdrd_dwc3_0: dwc3@fe800000 { > - compatible = "snps,dwc3"; > - reg = <0x0 0xfe800000 0x0 0x100000>; > - interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; > - dr_mode = "otg"; > - }; > - }; > - > - usbdrd3_1: usb@fe900000 { > - compatible = "rockchip,rk3399-dwc3"; > - clocks = <&cru SCLK_USB3OTG1_REF>, <&cru SCLK_USB3OTG1_SUSPEND>, > - <&cru ACLK_USB3OTG1>, <&cru ACLK_USB3_GRF>; > - clock-names = "ref_clk", "suspend_clk", > - "bus_clk", "grf_clk"; > - #address-cells = <2>; > - #size-cells = <2>; > - ranges; > - usbdrd_dwc3_1: dwc3@fe900000 { > - compatible = "snps,dwc3"; > - reg = <0x0 0xfe900000 0x0 0x100000>; > - interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; > - dr_mode = "otg"; > - }; > - }; > diff --git a/Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml b/Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml > new file mode 100644 > index 000000000..fdf9497bc > --- /dev/null > +++ b/Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml > @@ -0,0 +1,103 @@ > +# SPDX-License-Identifier: GPL-2.0 > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/usb/rockchip,dwc3.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Rockchip SuperSpeed DWC3 USB SoC controller > + > +maintainers: > + - Heiko Stuebner <heiko@sntech.de> > + > +description: > + The common content of the node is defined in snps,dwc3.yaml. > + > + Phy documentation is provided in the following places. > + > + USB2.0 PHY > + Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.yaml > + > + Type-C PHY > + Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt wrong indentation: expected 2 but found 6 (indentation) yamllint ./Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml This warning doesn't seem to show up with the command below. make ARCH=arm64 dt_binding_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml > + > +allOf: > + - $ref: snps,dwc3.yaml# No warning is given here with dt_binding_check. From patchwork log: Unknown file referenced: [Errno 2] No such file or directory: '/usr/local/lib/python3.8/dist-packages/dtschema/schemas/usb/snps,dwc3.yaml' ///// What's the correct format? - $ref: snps,dwc3.yaml# or - $ref: "snps,dwc3.yaml#" ///// This serie is for linux-next. What kernel version does patchwork work test with? https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20210203165233.22177-1-jbx6244@gmail.com/ > + > +properties: > + compatible: > + items: > + - enum: > + - rockchip,rk3399-dwc3 > + - const: snps,dwc3 > + > + reg: > + maxItems: 1 > + > + interrupts: > + maxItems: 1 > + > + clocks: > + items: > + - description: > + Controller reference clock, must to be 24 MHz > + - description: > + Controller suspend clock, must to be 24 MHz or 32 KHz > + - description: > + Master/Core clock, must to be >= 62.5 MHz for SS > + operation and >= 30MHz for HS operation > + - description: > + Controller aclk_usb3_rksoc_axi_perf clock > + - description: > + Controller aclk_usb3 clock > + - description: > + Controller grf clock > + > + clock-names: > + items: > + - const: ref_clk > + - const: suspend_clk > + - const: bus_clk > + - const: aclk_usb3_rksoc_axi_perf > + - const: aclk_usb3 > + - const: grf_clk > + > + power-domains: > + maxItems: 1 > + > + resets: > + maxItems: 1 > + > + reset-names: > + const: usb3-otg > + > +unevaluatedProperties: false > + > +required: > + - compatible > + - reg > + - interrupts > + - clocks > + - clock-names > + > +examples: > + - | > + #include <dt-bindings/clock/rk3399-cru.h> > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + > + bus { > + #address-cells = <2>; > + #size-cells = <2>; > + > + usbdrd3_0: usb@fe800000 { > + compatible = "rockchip,rk3399-dwc3", "snps,dwc3"; > + reg = <0x0 0xfe800000 0x0 0x100000>; > + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&cru SCLK_USB3OTG0_REF>, <&cru SCLK_USB3OTG0_SUSPEND>, > + <&cru ACLK_USB3OTG0>, <&cru ACLK_USB3_RKSOC_AXI_PERF>, > + <&cru ACLK_USB3>, <&cru ACLK_USB3_GRF>; > + clock-names = "ref_clk", "suspend_clk", > + "bus_clk", "aclk_usb3_rksoc_axi_perf", > + "aclk_usb3", "grf_clk"; > + dr_mode = "otg"; > + }; > + }; >
On 2021-02-03 16:52, Johan Jonker wrote: > In the past Rockchip dwc3 usb nodes were manually checked. > With the conversion of snps,dwc3.yaml as common document > we now can convert rockchip,dwc3.txt to yaml as well. > Remove node wrapper. > > Added properties for rk3399 are: > power-domains > resets > reset-names > > Signed-off-by: Johan Jonker <jbx6244@gmail.com> > --- > .../devicetree/bindings/usb/rockchip,dwc3.txt | 56 ----------- > .../devicetree/bindings/usb/rockchip,dwc3.yaml | 103 +++++++++++++++++++++ > 2 files changed, 103 insertions(+), 56 deletions(-) > delete mode 100644 Documentation/devicetree/bindings/usb/rockchip,dwc3.txt > create mode 100644 Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml > > diff --git a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt > deleted file mode 100644 > index 945204932..000000000 > --- a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt > +++ /dev/null > @@ -1,56 +0,0 @@ > -Rockchip SuperSpeed DWC3 USB SoC controller > - > -Required properties: > -- compatible: should contain "rockchip,rk3399-dwc3" for rk3399 SoC > -- clocks: A list of phandle + clock-specifier pairs for the > - clocks listed in clock-names > -- clock-names: Should contain the following: > - "ref_clk" Controller reference clk, have to be 24 MHz > - "suspend_clk" Controller suspend clk, have to be 24 MHz or 32 KHz > - "bus_clk" Master/Core clock, have to be >= 62.5 MHz for SS > - operation and >= 30MHz for HS operation > - "grf_clk" Controller grf clk > - > -Required child node: > -A child node must exist to represent the core DWC3 IP block. The name of > -the node is not important. The content of the node is defined in dwc3.txt. > - > -Phy documentation is provided in the following places: > -Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.yaml - USB2.0 PHY > -Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt - Type-C PHY > - > -Example device nodes: > - > - usbdrd3_0: usb@fe800000 { > - compatible = "rockchip,rk3399-dwc3"; > - clocks = <&cru SCLK_USB3OTG0_REF>, <&cru SCLK_USB3OTG0_SUSPEND>, > - <&cru ACLK_USB3OTG0>, <&cru ACLK_USB3_GRF>; > - clock-names = "ref_clk", "suspend_clk", > - "bus_clk", "grf_clk"; > - #address-cells = <2>; > - #size-cells = <2>; > - ranges; > - usbdrd_dwc3_0: dwc3@fe800000 { > - compatible = "snps,dwc3"; > - reg = <0x0 0xfe800000 0x0 0x100000>; > - interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; > - dr_mode = "otg"; > - }; > - }; > - > - usbdrd3_1: usb@fe900000 { > - compatible = "rockchip,rk3399-dwc3"; > - clocks = <&cru SCLK_USB3OTG1_REF>, <&cru SCLK_USB3OTG1_SUSPEND>, > - <&cru ACLK_USB3OTG1>, <&cru ACLK_USB3_GRF>; > - clock-names = "ref_clk", "suspend_clk", > - "bus_clk", "grf_clk"; > - #address-cells = <2>; > - #size-cells = <2>; > - ranges; > - usbdrd_dwc3_1: dwc3@fe900000 { > - compatible = "snps,dwc3"; > - reg = <0x0 0xfe900000 0x0 0x100000>; > - interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; > - dr_mode = "otg"; > - }; > - }; > diff --git a/Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml b/Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml > new file mode 100644 > index 000000000..fdf9497bc > --- /dev/null > +++ b/Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml > @@ -0,0 +1,103 @@ > +# SPDX-License-Identifier: GPL-2.0 > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/usb/rockchip,dwc3.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Rockchip SuperSpeed DWC3 USB SoC controller > + > +maintainers: > + - Heiko Stuebner <heiko@sntech.de> > + > +description: > + The common content of the node is defined in snps,dwc3.yaml. > + > + Phy documentation is provided in the following places. > + > + USB2.0 PHY > + Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.yaml > + > + Type-C PHY > + Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt > + > +allOf: > + - $ref: snps,dwc3.yaml# > + > +properties: > + compatible: > + items: > + - enum: > + - rockchip,rk3399-dwc3 > + - const: snps,dwc3 > + > + reg: > + maxItems: 1 > + > + interrupts: > + maxItems: 1 > + > + clocks: > + items: > + - description: > + Controller reference clock, must to be 24 MHz > + - description: > + Controller suspend clock, must to be 24 MHz or 32 KHz > + - description: > + Master/Core clock, must to be >= 62.5 MHz for SS > + operation and >= 30MHz for HS operation > + - description: > + Controller aclk_usb3_rksoc_axi_perf clock I'm pretty sure these last 3 don't belong to the controller itself, hence why they were in the glue layer node to being with. > + - description: > + Controller aclk_usb3 clock Does anything in the USB3 block actually consume this clock directly? If not, then I don't think it needs to be specified since it's already the parent of the controller's required bus_clk. I'm similarly suspicious of ACLK_USB3_NOC which is currently marked as CLK_IGNORE_UNUSED - if that's necessary for USB3 to function then it probably *should* be specified as part of the glue layer binding here. Robin. > + - description: > + Controller grf clock > + > + clock-names: > + items: > + - const: ref_clk > + - const: suspend_clk > + - const: bus_clk > + - const: aclk_usb3_rksoc_axi_perf > + - const: aclk_usb3 > + - const: grf_clk > + > + power-domains: > + maxItems: 1 > + > + resets: > + maxItems: 1 > + > + reset-names: > + const: usb3-otg > + > +unevaluatedProperties: false > + > +required: > + - compatible > + - reg > + - interrupts > + - clocks > + - clock-names > + > +examples: > + - | > + #include <dt-bindings/clock/rk3399-cru.h> > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + > + bus { > + #address-cells = <2>; > + #size-cells = <2>; > + > + usbdrd3_0: usb@fe800000 { > + compatible = "rockchip,rk3399-dwc3", "snps,dwc3"; > + reg = <0x0 0xfe800000 0x0 0x100000>; > + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&cru SCLK_USB3OTG0_REF>, <&cru SCLK_USB3OTG0_SUSPEND>, > + <&cru ACLK_USB3OTG0>, <&cru ACLK_USB3_RKSOC_AXI_PERF>, > + <&cru ACLK_USB3>, <&cru ACLK_USB3_GRF>; > + clock-names = "ref_clk", "suspend_clk", > + "bus_clk", "aclk_usb3_rksoc_axi_perf", > + "aclk_usb3", "grf_clk"; > + dr_mode = "otg"; > + }; > + }; >
Hi Robin, Thank you for your comments. The old binding txt is not so up to date. The question is now what do we add or not.. On 2/4/21 12:35 PM, Robin Murphy wrote: > On 2021-02-03 16:52, Johan Jonker wrote: >> In the past Rockchip dwc3 usb nodes were manually checked. >> With the conversion of snps,dwc3.yaml as common document >> we now can convert rockchip,dwc3.txt to yaml as well. >> Remove node wrapper. >> >> Added properties for rk3399 are: >> power-domains >> resets >> reset-names >> >> Signed-off-by: Johan Jonker <jbx6244@gmail.com> >> --- >> .../devicetree/bindings/usb/rockchip,dwc3.txt | 56 ----------- >> .../devicetree/bindings/usb/rockchip,dwc3.yaml | 103 >> +++++++++++++++++++++ >> 2 files changed, 103 insertions(+), 56 deletions(-) >> delete mode 100644 >> Documentation/devicetree/bindings/usb/rockchip,dwc3.txt >> create mode 100644 >> Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml >> >> diff --git a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt >> b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt >> deleted file mode 100644 >> index 945204932..000000000 >> --- a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt >> +++ /dev/null >> @@ -1,56 +0,0 @@ >> -Rockchip SuperSpeed DWC3 USB SoC controller >> - >> -Required properties: >> -- compatible: should contain "rockchip,rk3399-dwc3" for rk3399 SoC >> -- clocks: A list of phandle + clock-specifier pairs for the >> - clocks listed in clock-names >> -- clock-names: Should contain the following: >> - "ref_clk" Controller reference clk, have to be 24 MHz >> - "suspend_clk" Controller suspend clk, have to be 24 MHz or 32 KHz >> - "bus_clk" Master/Core clock, have to be >= 62.5 MHz for SS >> - operation and >= 30MHz for HS operation >> - "grf_clk" Controller grf clk >> - >> -Required child node: >> -A child node must exist to represent the core DWC3 IP block. The name of >> -the node is not important. The content of the node is defined in >> dwc3.txt. >> - >> -Phy documentation is provided in the following places: >> -Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.yaml - >> USB2.0 PHY >> -Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt - >> Type-C PHY >> - >> -Example device nodes: >> - >> - usbdrd3_0: usb@fe800000 { >> - compatible = "rockchip,rk3399-dwc3"; >> - clocks = <&cru SCLK_USB3OTG0_REF>, <&cru SCLK_USB3OTG0_SUSPEND>, >> - <&cru ACLK_USB3OTG0>, <&cru ACLK_USB3_GRF>; >> - clock-names = "ref_clk", "suspend_clk", >> - "bus_clk", "grf_clk"; >> - #address-cells = <2>; >> - #size-cells = <2>; >> - ranges; >> - usbdrd_dwc3_0: dwc3@fe800000 { >> - compatible = "snps,dwc3"; >> - reg = <0x0 0xfe800000 0x0 0x100000>; >> - interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; >> - dr_mode = "otg"; >> - }; >> - }; >> - >> - usbdrd3_1: usb@fe900000 { >> - compatible = "rockchip,rk3399-dwc3"; >> - clocks = <&cru SCLK_USB3OTG1_REF>, <&cru SCLK_USB3OTG1_SUSPEND>, >> - <&cru ACLK_USB3OTG1>, <&cru ACLK_USB3_GRF>; >> - clock-names = "ref_clk", "suspend_clk", >> - "bus_clk", "grf_clk"; >> - #address-cells = <2>; >> - #size-cells = <2>; >> - ranges; >> - usbdrd_dwc3_1: dwc3@fe900000 { >> - compatible = "snps,dwc3"; >> - reg = <0x0 0xfe900000 0x0 0x100000>; >> - interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; >> - dr_mode = "otg"; >> - }; >> - }; >> diff --git a/Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml >> b/Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml >> new file mode 100644 >> index 000000000..fdf9497bc >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml >> @@ -0,0 +1,103 @@ >> +# SPDX-License-Identifier: GPL-2.0 >> +%YAML 1.2 >> +--- >> +$id: http://devicetree.org/schemas/usb/rockchip,dwc3.yaml# >> +$schema: http://devicetree.org/meta-schemas/core.yaml# >> + >> +title: Rockchip SuperSpeed DWC3 USB SoC controller >> + >> +maintainers: >> + - Heiko Stuebner <heiko@sntech.de> >> + >> +description: >> + The common content of the node is defined in snps,dwc3.yaml. >> + >> + Phy documentation is provided in the following places. >> + >> + USB2.0 PHY >> + Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.yaml >> + >> + Type-C PHY >> + Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt >> + >> +allOf: >> + - $ref: snps,dwc3.yaml# Could Rob advise here? Is this OK or not? >> + >> +properties: >> + compatible: >> + items: >> + - enum: >> + - rockchip,rk3399-dwc3 >> + - const: snps,dwc3 >> + >> + reg: >> + maxItems: 1 >> + >> + interrupts: >> + maxItems: 1 >> + >> + clocks: >> + items: >> + - description: >> + Controller reference clock, must to be 24 MHz >> + - description: >> + Controller suspend clock, must to be 24 MHz or 32 KHz >> + - description: >> + Master/Core clock, must to be >= 62.5 MHz for SS >> + operation and >= 30MHz for HS operation >> + - description: >> + Controller aclk_usb3_rksoc_axi_perf clock > > I'm pretty sure these last 3 don't belong to the controller itself, > hence why they were in the glue layer node to being with. New proposal: clocks = <&cru SCLK_USB3OTG0_REF>, <&cru SCLK_USB3OTG0_SUSPEND>, <&cru ACLK_USB3OTG0>, <&cru ACLK_USB3_GRF>; clock-names = "ref_clk", "suspend_clk", "bus_clk", "grf_clk"; Clocks seem to be enabled in bulk. ret = clk_bulk_get_all(simple->dev, &simple->clks); With dt checks no longer able to add "@" in the nodename without reg property in the node. Given only clocks left in parent node and Rob's comment I've combined all in 1 node. > >> + - description: >> + Controller aclk_usb3 clock > > Does anything in the USB3 block actually consume this clock directly? If > not, then I don't think it needs to be specified since it's already the > parent of the controller's required bus_clk. The patch from the manufacturer tree in the link below seems to confirm this. //// From manufacturer tree: arm64: dts: rockchip: optimize clks for rk3399 dwc3 https://github.com/rockchip-linux/kernel/commit/1948bffacbc7a893d550141a63664b596717623a remove unnecessary clocks, refer to rk3399 TRM, aclk_usb3 is the parent of aclk_usb3otg0/1 and aclk_usb3_grf, and we will enable aclk_usb3otg0/1 and aclk_usb3_grf, so don't need to enable aclk_usb3 again. In addition, the aclk_usb3_rksoc_axi_perf clk is used for usb3 performance monitor module which we don't use now, so don't need to enable it. //// > > I'm similarly suspicious of ACLK_USB3_NOC which is currently marked as > CLK_IGNORE_UNUSED - if that's necessary for USB3 to function then it > probably *should* be specified as part of the glue layer binding here. Don't know about ACLK_USB3_NOC. I leave it as it is for now. > > Robin. > >> + - description: >> + Controller grf clock >> + >> + clock-names: >> + items: >> + - const: ref_clk >> + - const: suspend_clk >> + - const: bus_clk >> + - const: aclk_usb3_rksoc_axi_perf >> + - const: aclk_usb3 Remove these ?? >> + - const: grf_clk >> + >> + power-domains: >> + maxItems: 1 >> + >> + resets: >> + maxItems: 1 >> + >> + reset-names: >> + const: usb3-otg From manufacturer tree: arm64: dts: rockchip: move resets to the subnode of dwc3 for rk3399 https://github.com/rockchip-linux/kernel/commit/966da4dbacab847825f50a70036baacd74b2358d //// In mainline: /* * Some controllers need to toggle the usb3-otg reset before trying to * initialize the PHY, otherwise the PHY times out. */ if (of_device_is_compatible(np, "rockchip,rk3399-dwc3")) simple->need_reset = true; simple->resets = of_reset_control_array_get(np, false, true, true); //// Do we still need "reset-names" here?? >> + >> +unevaluatedProperties: false >> + >> +required: >> + - compatible >> + - reg >> + - interrupts >> + - clocks >> + - clock-names >> + >> +examples: >> + - | >> + #include <dt-bindings/clock/rk3399-cru.h> >> + #include <dt-bindings/interrupt-controller/arm-gic.h> >> + >> + bus { >> + #address-cells = <2>; >> + #size-cells = <2>; >> + >> + usbdrd3_0: usb@fe800000 { >> + compatible = "rockchip,rk3399-dwc3", "snps,dwc3"; >> + reg = <0x0 0xfe800000 0x0 0x100000>; >> + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; >> + clocks = <&cru SCLK_USB3OTG0_REF>, <&cru SCLK_USB3OTG0_SUSPEND>, >> + <&cru ACLK_USB3OTG0>, <&cru ACLK_USB3_RKSOC_AXI_PERF>, >> + <&cru ACLK_USB3>, <&cru ACLK_USB3_GRF>; >> + clock-names = "ref_clk", "suspend_clk", >> + "bus_clk", "aclk_usb3_rksoc_axi_perf", >> + "aclk_usb3", "grf_clk"; >> + dr_mode = "otg"; >> + }; >> + }; >>
On Wed, 03 Feb 2021 17:52:27 +0100, Johan Jonker wrote: > In the past Rockchip dwc3 usb nodes were manually checked. > With the conversion of snps,dwc3.yaml as common document > we now can convert rockchip,dwc3.txt to yaml as well. > Remove node wrapper. > > Added properties for rk3399 are: > power-domains > resets > reset-names > > Signed-off-by: Johan Jonker <jbx6244@gmail.com> > --- > .../devicetree/bindings/usb/rockchip,dwc3.txt | 56 ----------- > .../devicetree/bindings/usb/rockchip,dwc3.yaml | 103 +++++++++++++++++++++ > 2 files changed, 103 insertions(+), 56 deletions(-) > delete mode 100644 Documentation/devicetree/bindings/usb/rockchip,dwc3.txt > create mode 100644 Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml > My bot found errors running 'make dt_binding_check' on your patch: yamllint warnings/errors: ./Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml:13:7: [warning] wrong indentation: expected 2 but found 6 (indentation) dtschema/dtc warnings/errors: Unknown file referenced: [Errno 2] No such file or directory: '/usr/local/lib/python3.8/dist-packages/dtschema/schemas/usb/snps,dwc3.yaml' xargs: dt-doc-validate: exited with status 255; aborting make[1]: *** Deleting file 'Documentation/devicetree/bindings/usb/qcom,dwc3.example.dt.yaml' Unknown file referenced: [Errno 2] No such file or directory: '/usr/local/lib/python3.8/dist-packages/dtschema/schemas/usb/snps,dwc3.yaml' make[1]: *** [scripts/Makefile.lib:344: Documentation/devicetree/bindings/usb/qcom,dwc3.example.dt.yaml] Error 255 make[1]: *** Waiting for unfinished jobs.... make[1]: *** Deleting file 'Documentation/devicetree/bindings/usb/intel,keembay-dwc3.example.dt.yaml' Unknown file referenced: [Errno 2] No such file or directory: '/usr/local/lib/python3.8/dist-packages/dtschema/schemas/usb/snps,dwc3.yaml' make[1]: *** [scripts/Makefile.lib:344: Documentation/devicetree/bindings/usb/intel,keembay-dwc3.example.dt.yaml] Error 255 make[1]: *** Deleting file 'Documentation/devicetree/bindings/usb/amlogic,meson-g12a-usb-ctrl.example.dt.yaml' Unknown file referenced: [Errno 2] No such file or directory: '/usr/local/lib/python3.8/dist-packages/dtschema/schemas/usb/snps,dwc3.yaml' make[1]: *** [scripts/Makefile.lib:344: Documentation/devicetree/bindings/usb/amlogic,meson-g12a-usb-ctrl.example.dt.yaml] Error 255 make: *** [Makefile:1370: dt_binding_check] Error 2 See https://patchwork.ozlabs.org/patch/1435466 This check can fail if there are any dependencies. The base for a patch series is generally the most recent rc1. If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date: pip3 install dtschema --upgrade Please check and re-submit.
diff --git a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt deleted file mode 100644 index 945204932..000000000 --- a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt +++ /dev/null @@ -1,56 +0,0 @@ -Rockchip SuperSpeed DWC3 USB SoC controller - -Required properties: -- compatible: should contain "rockchip,rk3399-dwc3" for rk3399 SoC -- clocks: A list of phandle + clock-specifier pairs for the - clocks listed in clock-names -- clock-names: Should contain the following: - "ref_clk" Controller reference clk, have to be 24 MHz - "suspend_clk" Controller suspend clk, have to be 24 MHz or 32 KHz - "bus_clk" Master/Core clock, have to be >= 62.5 MHz for SS - operation and >= 30MHz for HS operation - "grf_clk" Controller grf clk - -Required child node: -A child node must exist to represent the core DWC3 IP block. The name of -the node is not important. The content of the node is defined in dwc3.txt. - -Phy documentation is provided in the following places: -Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.yaml - USB2.0 PHY -Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt - Type-C PHY - -Example device nodes: - - usbdrd3_0: usb@fe800000 { - compatible = "rockchip,rk3399-dwc3"; - clocks = <&cru SCLK_USB3OTG0_REF>, <&cru SCLK_USB3OTG0_SUSPEND>, - <&cru ACLK_USB3OTG0>, <&cru ACLK_USB3_GRF>; - clock-names = "ref_clk", "suspend_clk", - "bus_clk", "grf_clk"; - #address-cells = <2>; - #size-cells = <2>; - ranges; - usbdrd_dwc3_0: dwc3@fe800000 { - compatible = "snps,dwc3"; - reg = <0x0 0xfe800000 0x0 0x100000>; - interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; - dr_mode = "otg"; - }; - }; - - usbdrd3_1: usb@fe900000 { - compatible = "rockchip,rk3399-dwc3"; - clocks = <&cru SCLK_USB3OTG1_REF>, <&cru SCLK_USB3OTG1_SUSPEND>, - <&cru ACLK_USB3OTG1>, <&cru ACLK_USB3_GRF>; - clock-names = "ref_clk", "suspend_clk", - "bus_clk", "grf_clk"; - #address-cells = <2>; - #size-cells = <2>; - ranges; - usbdrd_dwc3_1: dwc3@fe900000 { - compatible = "snps,dwc3"; - reg = <0x0 0xfe900000 0x0 0x100000>; - interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; - dr_mode = "otg"; - }; - }; diff --git a/Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml b/Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml new file mode 100644 index 000000000..fdf9497bc --- /dev/null +++ b/Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml @@ -0,0 +1,103 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/usb/rockchip,dwc3.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip SuperSpeed DWC3 USB SoC controller + +maintainers: + - Heiko Stuebner <heiko@sntech.de> + +description: + The common content of the node is defined in snps,dwc3.yaml. + + Phy documentation is provided in the following places. + + USB2.0 PHY + Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.yaml + + Type-C PHY + Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt + +allOf: + - $ref: snps,dwc3.yaml# + +properties: + compatible: + items: + - enum: + - rockchip,rk3399-dwc3 + - const: snps,dwc3 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: + Controller reference clock, must to be 24 MHz + - description: + Controller suspend clock, must to be 24 MHz or 32 KHz + - description: + Master/Core clock, must to be >= 62.5 MHz for SS + operation and >= 30MHz for HS operation + - description: + Controller aclk_usb3_rksoc_axi_perf clock + - description: + Controller aclk_usb3 clock + - description: + Controller grf clock + + clock-names: + items: + - const: ref_clk + - const: suspend_clk + - const: bus_clk + - const: aclk_usb3_rksoc_axi_perf + - const: aclk_usb3 + - const: grf_clk + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + reset-names: + const: usb3-otg + +unevaluatedProperties: false + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +examples: + - | + #include <dt-bindings/clock/rk3399-cru.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + bus { + #address-cells = <2>; + #size-cells = <2>; + + usbdrd3_0: usb@fe800000 { + compatible = "rockchip,rk3399-dwc3", "snps,dwc3"; + reg = <0x0 0xfe800000 0x0 0x100000>; + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru SCLK_USB3OTG0_REF>, <&cru SCLK_USB3OTG0_SUSPEND>, + <&cru ACLK_USB3OTG0>, <&cru ACLK_USB3_RKSOC_AXI_PERF>, + <&cru ACLK_USB3>, <&cru ACLK_USB3_GRF>; + clock-names = "ref_clk", "suspend_clk", + "bus_clk", "aclk_usb3_rksoc_axi_perf", + "aclk_usb3", "grf_clk"; + dr_mode = "otg"; + }; + };
In the past Rockchip dwc3 usb nodes were manually checked. With the conversion of snps,dwc3.yaml as common document we now can convert rockchip,dwc3.txt to yaml as well. Remove node wrapper. Added properties for rk3399 are: power-domains resets reset-names Signed-off-by: Johan Jonker <jbx6244@gmail.com> --- .../devicetree/bindings/usb/rockchip,dwc3.txt | 56 ----------- .../devicetree/bindings/usb/rockchip,dwc3.yaml | 103 +++++++++++++++++++++ 2 files changed, 103 insertions(+), 56 deletions(-) delete mode 100644 Documentation/devicetree/bindings/usb/rockchip,dwc3.txt create mode 100644 Documentation/devicetree/bindings/usb/rockchip,dwc3.yaml