diff mbox series

[PULL,03/24] hw/arm/boot: Avoid placing the initrd on top of the kernel

Message ID 20190617143412.5734-4-peter.maydell@linaro.org
State New
Headers show
Series [PULL,01/24] hw/arm/boot: Don't assume RAM starts at address zero | expand

Commit Message

Peter Maydell June 17, 2019, 2:33 p.m. UTC 
We currently put the initrd at the smaller of:
 * 128MB into RAM
 * halfway into the RAM
(with the dtb following it).

However for large kernels this might mean that the kernel
overlaps the initrd. For some kinds of kernel (self-decompressing
32-bit kernels, and ELF images with a BSS section at the end)
we don't know the exact size, but even there we have a
minimum size. Put the initrd at least further into RAM than
that. For image formats that can give us an exact kernel size, this
will mean that we definitely avoid overlaying kernel and initrd.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Message-id: 20190516144733.32399-4-peter.maydell@linaro.org
---
 hw/arm/boot.c | 34 ++++++++++++++++++++--------------
 1 file changed, 20 insertions(+), 14 deletions(-)
diff mbox series

Patch

diff --git a/hw/arm/boot.c b/hw/arm/boot.c
index 5ddba727d45..a0e1110719e 100644
--- a/hw/arm/boot.c
+++ b/hw/arm/boot.c
@@ -1000,20 +1000,6 @@  static void arm_setup_direct_kernel_boot(ARMCPU *cpu,
     if (info->nb_cpus == 0)
         info->nb_cpus = 1;
 
-    /*
-     * We want to put the initrd far enough into RAM that when the
-     * kernel is uncompressed it will not clobber the initrd. However
-     * on boards without much RAM we must ensure that we still leave
-     * enough room for a decent sized initrd, and on boards with large
-     * amounts of RAM we must avoid the initrd being so far up in RAM
-     * that it is outside lowmem and inaccessible to the kernel.
-     * So for boards with less  than 256MB of RAM we put the initrd
-     * halfway into RAM, and for boards with 256MB of RAM or more we put
-     * the initrd at 128MB.
-     */
-    info->initrd_start = info->loader_start +
-        MIN(info->ram_size / 2, 128 * 1024 * 1024);
-
     /* Assume that raw images are linux kernels, and ELF images are not.  */
     kernel_size = arm_load_elf(info, &elf_entry, &elf_low_addr,
                                &elf_high_addr, elf_machine, as);
@@ -1065,6 +1051,26 @@  static void arm_setup_direct_kernel_boot(ARMCPU *cpu,
     }
 
     info->entry = entry;
+
+    /*
+     * We want to put the initrd far enough into RAM that when the
+     * kernel is uncompressed it will not clobber the initrd. However
+     * on boards without much RAM we must ensure that we still leave
+     * enough room for a decent sized initrd, and on boards with large
+     * amounts of RAM we must avoid the initrd being so far up in RAM
+     * that it is outside lowmem and inaccessible to the kernel.
+     * So for boards with less  than 256MB of RAM we put the initrd
+     * halfway into RAM, and for boards with 256MB of RAM or more we put
+     * the initrd at 128MB.
+     * We also refuse to put the initrd somewhere that will definitely
+     * overlay the kernel we just loaded, though for kernel formats which
+     * don't tell us their exact size (eg self-decompressing 32-bit kernels)
+     * we might still make a bad choice here.
+     */
+    info->initrd_start = info->loader_start +
+        MAX(MIN(info->ram_size / 2, 128 * 1024 * 1024), kernel_size);
+    info->initrd_start = TARGET_PAGE_ALIGN(info->initrd_start);
+
     if (is_linux) {
         uint32_t fixupcontext[FIXUP_MAX];