@@ -204,7 +204,7 @@ AT_SKIP_IF([test $HAVE_PYTHON = no])
ovn_start
ovn-nbctl ls-add S1
-ovn-nbctl lsp-add S1 S1-vm1
+ovn-nbctl --wait=sb lsp-add S1 S1-vm1
AT_CHECK([test x`ovn-nbctl lsp-get-up S1-vm1` = xdown])
ovn-sbctl chassis-add hv1 geneve 127.0.0.1
@@ -224,7 +224,7 @@ ovn-nbctl ls-add S1
ovn-nbctl lsp-add S1 S1-R1
ovn-nbctl lsp-set-type S1-R1 router
ovn-nbctl lsp-set-addresses S1-R1 02:ac:10:01:00:01
-ovn-nbctl lsp-set-options S1-R1 router-port=R1-S1
+ovn-nbctl --wait=sb lsp-set-options S1-R1 router-port=R1-S1
AT_CHECK([test x`ovn-nbctl lsp-get-up S1-R1` = xup])
AT_CLEANUP
@@ -242,7 +242,7 @@ ovn-nbctl ls-add S1
ovn-nbctl lsp-add S1 S1-R1
ovn-nbctl lsp-set-type S1-R1 router
ovn-nbctl lsp-set-addresses S1-R1 02:ac:10:01:00:01
-ovn-nbctl lsp-set-options S1-R1 router-port=R1-S1
+ovn-nbctl --wait=sb lsp-set-options S1-R1 router-port=R1-S1
ovn-sbctl lsp-bind S1-R1 gw1
AT_CHECK([test x`ovn-nbctl lsp-get-up S1-R1` = xup])
@@ -263,7 +263,7 @@ ovn-nbctl ls-add S1
ovn-nbctl lsp-add S1 S1-R1
ovn-nbctl lsp-set-type S1-R1 router
ovn-nbctl lsp-set-addresses S1-R1 router
-ovn-nbctl lsp-set-options S1-R1 router-port=R1-S1
+ovn-nbctl --wait=sb lsp-set-options S1-R1 router-port=R1-S1
AT_CHECK([test x`ovn-nbctl lsp-get-up S1-R1` = xup])
AT_CLEANUP
@@ -1689,7 +1689,7 @@ for i in 1 2; do
ovn-nbctl lsp-add lsw0 lp$i$j
ip_addrs="192.168.0.$i$j"
ovn-nbctl lsp-set-addresses lp$i$j "f0:00:00:00:00:$i$j $ip_addrs"
- ovn-nbctl lsp-set-port-security lp$i$j f0:00:00:00:00:$i$j
+ ovn-nbctl --wait=hv lsp-set-port-security lp$i$j
f0:00:00:00:00:$i$j
done
done
Several of the ovn tests did not use the `--wait` flag to to wait for a configuration change to propagate through the system. As a result, these tests fail when `ovn-northd` is slow. Fixed by adding `--wait=hv` or `--wait=sb` as appropriate. Signed-off-by: Leonid Ryzhyk <ryzhyk@gmail.com> --- tests/ovn-northd.at | 8 ++++---- tests/ovn.at | 12 ++++++------ 2 files changed, 10 insertions(+), 10 deletions(-) @@ -7161,7 +7161,7 @@ ovn-nbctl acl-add lsw0 to-lport 1000 'tcp.dst==84' allow-related ovn-nbctl --log acl-add lsw0 to-lport 1000 'tcp.dst==85' allow-related ovn-nbctl acl-add lsw0 to-lport 1000 'tcp.dst==86' reject -ovn-nbctl --log --severity=alert --name=reject-flow acl-add lsw0 to-lport 1000 'tcp.dst==87' reject +ovn-nbctl --wait=hv --log --severity=alert --name=reject-flow acl-add lsw0 to-lport 1000 'tcp.dst==87' reject ovn-sbctl dump-flows @@ -7268,7 +7268,7 @@ ovn-nbctl --log --severity=alert --meter=http-rl2 --name=http-acl2 acl-add lsw0 # Add an ACL that doesn't rate-limit logs. ovn-nbctl --log --severity=alert --name=http-acl3 acl-add lsw0 to-lport 1000 'tcp.dst==82' drop - +ovn-nbctl --wait=hv sync # For each ACL, send 100 packets. for i in `seq 1 100`; do @@ -12058,7 +12058,7 @@ AT_CHECK([ovn-sbctl get Address_Set pg2_ip6 addresses], [0], [[["2001:db8:2::ff:fe00:2", "2001:db8:3::ff:fe00:3"]] ]) -ovn-nbctl set Logical_Switch ls1 \ +ovn-nbctl --wait=sb set Logical_Switch ls1 \ other_config:subnet=10.11.0.0/24 other_config:ipv6_prefix="2001:db8:11::" dnl Check if updated address got propagated to the port group address sets @@ -13370,7 +13370,7 @@ ovn-nbctl lsp-set-addresses sw1-p5 "unknown" ovn-nbctl list logical_switch_port # Now try to add duplicate addresses on a new port. These should all fail -ovn-nbctl lsp-add sw1 sw1-p5 +ovn-nbctl --wait=sb lsp-add sw1 sw1-p5 AT_CHECK([ovn-nbctl lsp-set-addresses sw1-p5 "00:00:00:00:00:04 10.0.0.1"], [1], [], [ovn-nbctl: Error on switch sw1: duplicate IPv4 address 10.0.0.1 ]) @@ -13829,7 +13829,7 @@ AT_CHECK([ovn-nbctl get Logical-Switch-Port p0 dynamic_addresses], [0], ["0a:00:00:a8:01:03 192.168.1.2" ]) -ovn-nbctl lsp-set-addresses p0 router +ovn-nbctl --wait=sb lsp-set-addresses p0 router ovn-nbctl get Logical-Switch-Port p0 dynamic_addresses