Message ID | 1343438093-13151-2-git-send-email-ronniesahlberg@gmail.com |
---|---|
State | New |
Headers | show |
Il 28/07/2012 03:14, Ronnie Sahlberg ha scritto: > The START STOP UNIT command will only eject/load media if > power condition is zero. > > If power condition is !0 then LOEJ and START will be ignored. > > From MMC (sbc contains similar wordings too) > The Power Conditions field requests the block device to be placed > in the power condition defined in > Table 558. If this field has a value other than 0h then the Start > and LoEj bits shall be ignored. > > Signed-off-by: Ronnie Sahlberg <ronniesahlberg@gmail.com> Applied, thanks. Paolo
Am 28.07.2012 03:14, schrieb Ronnie Sahlberg: > The START STOP UNIT command will only eject/load media if > power condition is zero. > > If power condition is !0 then LOEJ and START will be ignored. > > From MMC (sbc contains similar wordings too) > The Power Conditions field requests the block device to be placed > in the power condition defined in > Table 558. If this field has a value other than 0h then the Start > and LoEj bits shall be ignored. > > Signed-off-by: Ronnie Sahlberg <ronniesahlberg@gmail.com> Does ATAPI need the same? Kevin
Il 30/07/2012 10:20, Kevin Wolf ha scritto: > Am 28.07.2012 03:14, schrieb Ronnie Sahlberg: >> > The START STOP UNIT command will only eject/load media if >> > power condition is zero. >> > >> > If power condition is !0 then LOEJ and START will be ignored. >> > >> > From MMC (sbc contains similar wordings too) >> > The Power Conditions field requests the block device to be placed >> > in the power condition defined in >> > Table 558. If this field has a value other than 0h then the Start >> > and LoEj bits shall be ignored. >> > >> > Signed-off-by: Ronnie Sahlberg <ronniesahlberg@gmail.com> > Does ATAPI need the same? Yes, I already asked Ronnie to redo these two patches for ATAPI as well. Paolo
I will create a patch for ATAPI for this. On Mon, Jul 30, 2012 at 6:20 PM, Kevin Wolf <kwolf@redhat.com> wrote: > Am 28.07.2012 03:14, schrieb Ronnie Sahlberg: >> The START STOP UNIT command will only eject/load media if >> power condition is zero. >> >> If power condition is !0 then LOEJ and START will be ignored. >> >> From MMC (sbc contains similar wordings too) >> The Power Conditions field requests the block device to be placed >> in the power condition defined in >> Table 558. If this field has a value other than 0h then the Start >> and LoEj bits shall be ignored. >> >> Signed-off-by: Ronnie Sahlberg <ronniesahlberg@gmail.com> > > Does ATAPI need the same? > > Kevin
diff --git a/hw/scsi-disk.c b/hw/scsi-disk.c index 525816c..5426990 100644 --- a/hw/scsi-disk.c +++ b/hw/scsi-disk.c @@ -1244,6 +1244,12 @@ static int scsi_disk_emulate_start_stop(SCSIDiskReq *r) SCSIDiskState *s = DO_UPCAST(SCSIDiskState, qdev, req->dev); bool start = req->cmd.buf[4] & 1; bool loej = req->cmd.buf[4] & 2; /* load on start, eject on !start */ + int pwrcnd = req->cmd.buf[4] & 0xf0; + + if (pwrcnd) { + /* eject/load only happens for power condition == 0 */ + return 0; + } if (s->qdev.type == TYPE_ROM && loej) { if (!start && !s->tray_open && s->tray_locked) {
The START STOP UNIT command will only eject/load media if power condition is zero. If power condition is !0 then LOEJ and START will be ignored. From MMC (sbc contains similar wordings too) The Power Conditions field requests the block device to be placed in the power condition defined in Table 558. If this field has a value other than 0h then the Start and LoEj bits shall be ignored. Signed-off-by: Ronnie Sahlberg <ronniesahlberg@gmail.com> --- hw/scsi-disk.c | 6 ++++++ 1 files changed, 6 insertions(+), 0 deletions(-)