@@ -164,25 +164,39 @@ static const struct regmap_access_table rpcif_volatile_table = {
/*
- * Custom accessor functions to ensure SMRDR0 and SMWDR0 are always accessed
- * with proper width. Requires SMENR_SPIDE to be correctly set before!
+ * Custom accessor functions to ensure SM[RW]DR[01] are always accessed with
+ * proper width. Requires rpcif.xfer_size to be correctly set before!
*/
static int rpcif_reg_read(void *context, unsigned int reg, unsigned int *val)
{
struct rpcif *rpc = context;
- if (reg == RPCIF_SMRDR0 || reg == RPCIF_SMWDR0) {
- u32 spide = readl(rpc->base + RPCIF_SMENR) & RPCIF_SMENR_SPIDE(0xF);
-
- if (spide == 0x8) {
+ switch (reg) {
+ case RPCIF_SMRDR0:
+ case RPCIF_SMWDR0:
+ switch (rpc->xfer_size) {
+ case 1:
*val = readb(rpc->base + reg);
return 0;
- } else if (spide == 0xC) {
+
+ case 2:
*val = readw(rpc->base + reg);
return 0;
- } else if (spide != 0xF) {
+
+ case 4:
+ case 8:
+ *val = readl(rpc->base + reg);
+ return 0;
+
+ default:
return -EILSEQ;
}
+
+ case RPCIF_SMRDR1:
+ case RPCIF_SMWDR1:
+ if (rpc->xfer_size != 8)
+ return -EILSEQ;
+ break;
}
*val = readl(rpc->base + reg);
@@ -193,18 +207,34 @@ static int rpcif_reg_write(void *context, unsigned int reg, unsigned int val)
{
struct rpcif *rpc = context;
- if (reg == RPCIF_SMRDR0 || reg == RPCIF_SMWDR0) {
- u32 spide = readl(rpc->base + RPCIF_SMENR) & RPCIF_SMENR_SPIDE(0xF);
-
- if (spide == 0x8) {
+ switch (reg) {
+ case RPCIF_SMWDR0:
+ switch (rpc->xfer_size) {
+ case 1:
writeb(val, rpc->base + reg);
return 0;
- } else if (spide == 0xC) {
+
+ case 2:
writew(val, rpc->base + reg);
return 0;
- } else if (spide != 0xF) {
+
+ case 4:
+ case 8:
+ writel(val, rpc->base + reg);
+ return 0;
+
+ default:
return -EILSEQ;
}
+
+ case RPCIF_SMWDR1:
+ if (rpc->xfer_size != 8)
+ return -EILSEQ;
+ break;
+
+ case RPCIF_SMRDR0:
+ case RPCIF_SMRDR1:
+ return -EPERM;
}
writel(val, rpc->base + reg);
@@ -469,6 +499,7 @@ int rpcif_manual_xfer(struct rpcif *rpc)
smenr |= RPCIF_SMENR_SPIDE(rpcif_bits_set(rpc, nbytes));
regmap_write(rpc->regmap, RPCIF_SMENR, smenr);
+ rpc->xfer_size = nbytes;
memcpy(data, rpc->buffer + pos, nbytes);
if (nbytes == 8) {
@@ -533,6 +564,7 @@ int rpcif_manual_xfer(struct rpcif *rpc)
regmap_write(rpc->regmap, RPCIF_SMENR, smenr);
regmap_write(rpc->regmap, RPCIF_SMCR,
rpc->smcr | RPCIF_SMCR_SPIE);
+ rpc->xfer_size = nbytes;
ret = wait_msg_xfer_end(rpc);
if (ret)
goto err_out;
@@ -72,6 +72,7 @@ struct rpcif {
enum rpcif_type type;
enum rpcif_data_dir dir;
u8 bus_size;
+ u8 xfer_size;
void *buffer;
u32 xferlen;
u32 smcr;
HyperFlash devices fail to probe: rpc-if-hyperflash rpc-if-hyperflash: probing of hyperbus device failed In HyperFlash or Octal-SPI Flash mode, the Transfer Data Enable bits (SPIDE) in the Manual Mode Enable Setting Register (SMENR) are derived from half of the transfer size, cfr. the rpcif_bits_set() helper function. However, rpcif_reg_{read,write}() does not take the bus size into account, and does not double all Manual Mode Data Register access sizes when communicating with a HyperFlash or Octal-SPI Flash device. Fix this, and avoid the back-and-forth conversion between transfer size and Transfer Data Enable bits, by explicitly storing the transfer size in struct rpcif, and using that value to determine access size in rpcif_reg_{read,write}(). Enforce that the "high" Manual Mode Read/Write Data Registers (SM[RW]DR1) are only used for 8-byte data accesses. While at it, forbid writing to the Manual Mode Read Data Registers, as they are read-only. Fixes: fff53a551db50f5e ("memory: renesas-rpc-if: Correct QSPI data transfer in Manual mode") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> [QSPI] --- Lightly (read-only) tested on: - Salvator-XS, ULCB, Ebisu-4D, and Draak (with R-Car H3 ES1.1 and ES2.0, M3-W ES1.0, M3-N ES1.0, E3 ES1.0, and D3 ES1.0) with HyperFlash, - Falcon with R-Car V3U ES1.0 with QSPI. v3: - Add Tested-by, - Update comments to match changed code, - Add explicit {read,write}l() for the 4/8 byte case, to increase readability, - Remove redundant break statements, - Tested HyperFlash on more boards and SoCs. v2: - Use rpc->xfer_size instead of SPIDE register reads and rpc->bus_size. Note: Alternatively, rpcif_manual_xfer() could bypass regmap and use {read,write}[bwl]() directly, cfr. commit 0d37f69cacb33435 ("memory: renesas-rpc-if: Correct QSPI data transfer in Manual mode") in the BSP. - HF dirmap reads are confirmed to work on R-Car M3-W, - Drop RFC. --- drivers/memory/renesas-rpc-if.c | 60 +++++++++++++++++++++++++-------- include/memory/renesas-rpc-if.h | 1 + 2 files changed, 47 insertions(+), 14 deletions(-)