Message ID | 20190401115616.21337-1-megous@megous.com |
---|---|
Headers | show |
Series | Add bluetooth, gps and accelerometer to TBS A711 | expand |
On Mon, Apr 01, 2019 at 01:56:13PM +0200, megous@megous.com wrote: > From: Ondrej Jirman <megous@megous.com> > > Add pin definitions for UART2 PB pins. These are used on TBS-A711 > tablet. > > Signed-off-by: Ondrej Jirman <megous@megous.com> Applied, thanks! Maxime -- Maxime Ripard, Bootlin Embedded Linux and Kernel engineering https://bootlin.com
Hi, On Mon, Apr 01, 2019 at 01:56:12PM +0200, megous@megous.com wrote: > From: Ondrej Jirman <megous@megous.com> > > A711 tablet has BMA250 accelerometer connected to I2C1 bus. Enable > both the I2C1 bus and add the accelerometer device to it. > > Signed-off-by: Ondrej Jirman <megous@megous.com> > --- > arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts | 13 +++++++++++++ > 1 file changed, 13 insertions(+) > > diff --git a/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts b/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts > index 1e840ab5a541..d70fe04b66f0 100644 > --- a/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts > +++ b/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts > @@ -156,6 +156,19 @@ > status = "okay"; > }; > > +&i2c1 { > + clock-frequency = <400000>; > + status = "okay"; > + > + /* Accelerometer */ > + accelerometer@18 { > + compatible = "bosch,bma250"; > + reg = <0x18>; > + interrupt-parent = <&pio>; > + interrupts = <7 10 IRQ_TYPE_EDGE_RISING>; /* PH10 / EINT10 */ > + }; > +}; I've dropped the comment, since it's pretty obvious now, and applied, thanks! Maxime -- Maxime Ripard, Bootlin Embedded Linux and Kernel engineering https://bootlin.com
On Mon, Apr 01, 2019 at 01:56:11PM +0200, megous@megous.com wrote: > From: Ondrej Jirman <megous@megous.com> > > This series enables some peripherals on TBS A711 tablet that already > have mainline drivers: > > - GPS u-blox neo-6m (via gnss u-blox driver) > - Bluetooth (via recently added OF support in the Broadcom > bluetooth driver) > - Accelermomter BMA-250 (hooked to the I2C bus) > > It also modifies A83T DTSI and adds missing UART interfaces. > > I've added additional compatible to the gnss/u-blox driver for NEO-6M, > because this board uses this module, and I don't think I can use > the existing compatible for u-blox,neo-m8, even as a fallback. > > Please take a look, and apply the patches if you have no objections. > > Many of the patches will go through the sunxi tree, but I'm not > sure who will want to take the GPS patches. I'll take the GPS patches through my tree once I've had a chance to review them. Perhaps easiest to resend the corresponding dts change once that is done. Johan
Hello Maxime, On Mon, Apr 01, 2019 at 01:56:16PM +0200, megous via linux-sunxi wrote: > From: Ondrej Jirman <megous@megous.com> > > TBS A711 tablet contains u-blox NEO-6M module connected to UART2. > Enable UART2 to gain access to the module from userspace. Other GPS bits are now applied (thank you, Johan), so if this last bit can go in too via a sunxi tree, the series will be complete. thank you, Ondrej > Signed-off-by: Ondrej Jirman <megous@megous.com> > --- > arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts | 21 +++++++++++++++++++++ > 1 file changed, 21 insertions(+) > > diff --git a/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts b/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts > index d70fe04b66f0..fd170bc45927 100644 > --- a/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts > +++ b/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts > @@ -98,6 +98,13 @@ > }; > }; > > + reg_gps: reg-gps { > + compatible = "regulator-fixed"; > + regulator-name = "gps"; > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3000000>; > + }; > + > reg_vbat: reg-vbat { > compatible = "regulator-fixed"; > regulator-name = "vbat"; > @@ -422,6 +429,20 @@ > status = "okay"; > }; > > +&uart2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart2_pb_pins>; > + status = "okay"; > + > + gnss { > + compatible = "u-blox,neo-6m"; > + > + v-bckp-supply = <®_rtc_ldo>; > + vcc-supply = <®_gps>; > + current-speed = <9600>; > + }; > +}; > + > &usb_otg { > dr_mode = "otg"; > status = "okay"; > -- > 2.21.0 > > -- > You received this message because you are subscribed to the Google Groups "linux-sunxi" group. > To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@googlegroups.com. > For more options, visit https://groups.google.com/d/optout.
On Thu, Apr 04, 2019 at 02:43:22PM +0200, Ondřej Jirman wrote: > Hello Maxime, > > On Mon, Apr 01, 2019 at 01:56:16PM +0200, megous via linux-sunxi wrote: > > From: Ondrej Jirman <megous@megous.com> > > > > TBS A711 tablet contains u-blox NEO-6M module connected to UART2. > > Enable UART2 to gain access to the module from userspace. > > Other GPS bits are now applied (thank you, Johan), so if this last bit > can go in too via a sunxi tree, the series will be complete. Applied, thanks! Maxime -- Maxime Ripard, Bootlin Embedded Linux and Kernel engineering https://bootlin.com
From: Ondrej Jirman <megous@megous.com> This series enables some peripherals on TBS A711 tablet that already have mainline drivers: - GPS u-blox neo-6m (via gnss u-blox driver) - Bluetooth (via recently added OF support in the Broadcom bluetooth driver) - Accelermomter BMA-250 (hooked to the I2C bus) It also modifies A83T DTSI and adds missing UART interfaces. I've added additional compatible to the gnss/u-blox driver for NEO-6M, because this board uses this module, and I don't think I can use the existing compatible for u-blox,neo-m8, even as a fallback. Please take a look, and apply the patches if you have no objections. Many of the patches will go through the sunxi tree, but I'm not sure who will want to take the GPS patches. regards, Ondrej Jirman Changes in v2: - dropped already applied patches from the series (bluetooth, a83t uarts) - added /omit-if-no-ref/ to "uart2-pb-pins" - renamed node "bma250" to "accelerometer" - removed pinctrl properties that are already in base dtsi (i2c1_pins) Ondrej Jirman (5): ARM: dts: sun8i: tbs-a711: Add node for BMA250 accelerometer ARM: dts: sun8i: a83t: Add UART2 PB pins gnss: Add u-blox,neo-6m compatible dt-bindings: gnss: Add u-blox,neo-6m compatible ARM: dts: sun8i: tbs-a711: Enable UART2 (for NEO-6M GPS module) .../devicetree/bindings/gnss/u-blox.txt | 1 + arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts | 34 +++++++++++++++++++ arch/arm/boot/dts/sun8i-a83t.dtsi | 6 ++++ drivers/gnss/ubx.c | 1 + 4 files changed, 42 insertions(+)