[OpenWrt-Devel,1/3] ramips: Add support for GL-MT300A

This patches adds support for GL-MT300A.
GL-MT300A is powered by MT7620A. It has 16MB flash, 128MB RAM,
Two LANs, USB, UART and MMC daughter board.
---
 target/linux/ramips/base-files/etc/board.d/01_leds |   3 +
 .../linux/ramips/base-files/etc/board.d/02_network |   1 +
 target/linux/ramips/base-files/lib/ramips.sh       |   3 +
 .../ramips/base-files/lib/upgrade/platform.sh      |   1 +
 target/linux/ramips/dts/GL-MT300A.dts              | 164 +++++++++++++++++++++
 target/linux/ramips/image/Makefile                 |   2 +
 target/linux/ramips/mt7620/profiles/gli.mk         |  16 ++
 7 files changed, 190 insertions(+)
 create mode 100644 target/linux/ramips/dts/GL-MT300A.dts
 create mode 100644 target/linux/ramips/mt7620/profiles/gli.mk

ouch, none of these have a signed-off-by line and i noticed only after
pushing :(

On 10/03/2016 07:31, alzhao wrote:
> This patches adds support for GL-MT300A.
> GL-MT300A is powered by MT7620A. It has 16MB flash, 128MB RAM,
> Two LANs, USB, UART and MMC daughter board.
> ---
>  target/linux/ramips/base-files/etc/board.d/01_leds |   3 +
>  .../linux/ramips/base-files/etc/board.d/02_network |   1 +
>  target/linux/ramips/base-files/lib/ramips.sh       |   3 +
>  .../ramips/base-files/lib/upgrade/platform.sh      |   1 +
>  target/linux/ramips/dts/GL-MT300A.dts              | 164 +++++++++++++++++++++
>  target/linux/ramips/image/Makefile                 |   2 +
>  target/linux/ramips/mt7620/profiles/gli.mk         |  16 ++
>  7 files changed, 190 insertions(+)
>  create mode 100644 target/linux/ramips/dts/GL-MT300A.dts
>  create mode 100644 target/linux/ramips/mt7620/profiles/gli.mk
> 
> diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
> index 8fd50fe..536a363 100755
> --- a/target/linux/ramips/base-files/etc/board.d/01_leds
> +++ b/target/linux/ramips/base-files/etc/board.d/01_leds
> @@ -137,6 +137,9 @@ fonera20n)
>  	set_usb_led "$board:orange:usb"
>  	set_wifi_led "$board:orange:wifi"
>  	;;
> +gl-mt300a)
> +	set_wifi_led "$board:wlan"
> +	;;
>  hc5661)
>  	ucidef_set_led_default "system" "system" "$board:blue:system" "1"
>  	ucidef_set_led_netdev "internet" "internet" "$board:blue:internet" "eth0.2"
> diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
> index ac5a312..74599ad 100755
> --- a/target/linux/ramips/base-files/etc/board.d/02_network
> +++ b/target/linux/ramips/base-files/etc/board.d/02_network
> @@ -113,6 +113,7 @@ ramips_setup_interfaces()
>  	dir-860l-b1|\
>  	f5d8235-v1|\
>  	f5d8235-v2|\
> +	gl-mt300a|\
>  	hg255d|\
>  	mzk-wdpr|\
>  	jhr-n805r|\
> diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
> index 3fdb562..ba27c14 100755
> --- a/target/linux/ramips/base-files/lib/ramips.sh
> +++ b/target/linux/ramips/base-files/lib/ramips.sh
> @@ -175,6 +175,9 @@ ramips_board_detect() {
>  	*"FreeStation5")
>  		name="freestation5"
>  		;;
> +	*"GL-MT300A")
> +		name="gl-mt300a"
> +		;;
>  	*"HC5661")
>  		name="hc5661"
>  		;;
> diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> index e01f9ce..876416e 100755
> --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
> +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> @@ -56,6 +56,7 @@ platform_check_image() {
>  	firewrt|\
>  	fonera20n|\
>  	freestation5|\
> +	gl-mt300a|\
>  	hc5*61|\
>  	hg255d|\
>  	hlk-rm04|\
> diff --git a/target/linux/ramips/dts/GL-MT300A.dts b/target/linux/ramips/dts/GL-MT300A.dts
> new file mode 100644
> index 0000000..c1eb0a9
> --- /dev/null
> +++ b/target/linux/ramips/dts/GL-MT300A.dts
> @@ -0,0 +1,164 @@
> +/dts-v1/;
> +
> +/include/ "mt7620a.dtsi"
> +
> +/ {
> +	compatible = "GL-MT300A", "ralink,mt7620a-soc";
> +	model = "GL-MT300A";
> +
> +	chosen {
> +		bootargs = "console=ttyS0,115200";
> +	};
> +
> +	palmbus@10000000 {
> +		gpio0: gpio@600 {
> +			status = "okay";
> +		};
> +
> +		gpio1: gpio@638 {
> +			status = "okay";
> +		};
> +
> +		gpio2: gpio@660 {
> +			status = "okay";
> +		};
> +		
> +		gpio3: gpio@688 {
> +		      status = "okay";
> +		 };
> +
> +		spi@b00 {
> +			status = "okay";
> +
> +			m25p80@0 {
> +				#address-cells = <1>;
> +				#size-cells = <1>;
> +				compatible = "w25q128";
> +				reg = <0 0>;
> +				linux,modalias = "m25p80", "w25q128";
> +				spi-max-frequency = <10000000>;
> +
> +				partition@0 {
> +					label = "u-boot";
> +					reg = <0x0 0x30000>;
> +				};
> +
> +				partition@30000 {
> +					label = "u-boot-env";
> +					reg = <0x30000 0x10000>;
> +					read-only;
> +				};
> +
> +				factory: partition@40000 {
> +					label = "factory";
> +					reg = <0x40000 0x10000>;
> +					read-only;
> +				};
> +
> +				partition@50000 {
> +					label = "firmware";
> +					reg = <0x50000 0xf80000>;
> +				};
> +
> +				partition@ff0000 {
> +					label = "art";
> +					reg = <0xff0000 0x10000>;
> +				};
> +			};
> +		};
> +	};
> +
> +	sdhci@10130000 {
> +		status = "okay";
> +	};
> +
> +	ehci@101c0000 {
> +		status = "okay";
> +	};
> +
> +	ohci@101c1000 {
> +		status = "okay";
> +	};
> +
> +	ethernet@10100000 {
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&ephy_pins>;
> +		mtd-mac-address = <&factory 0x4000>;
> +		ralink,port-map = "wllll";
> +	};
> +
> +	wmac@10180000 {
> +		ralink,mtd-eeprom = <&factory 0>;
> +	};
> +
> +	pcie@10140000 {
> +		status = "okay";
> +
> +		pcie-bridge {
> +			mt76@0,0 {
> +				reg = <0x0000 0 0 0 0>;
> +				device_type = "pci";
> +				mediatek,mtd-eeprom = <&factory 0x8000>;
> +				mediatek,2ghz = <0>;
> +			};
> +		};
> +	};
> +
> +	pinctrl {
> +		state_default: pinctrl0 {
> +			gpio {
> +				ralink,group = "wled","ephy","uartf","i2c";
> +				ralink,function = "gpio";
> +			};
> +		};
> +	};
> +
> +	gpio-leds {
> +		compatible = "gpio-leds";
> +
> +		wan {
> +			label = "gl-mt300a:wan";
> +			gpios = <&gpio2 0 1>;
> +		};
> +
> +		lan {
> +			label = "gl-mt300a:lan";
> +			gpios = <&gpio2 1 1>;
> +		};
> +
> +		wlan {
> +			label = "gl-mt300a:wlan";
> +			gpios = <&gpio3 0 1>;
> +		};
> +
> +		usb {
> +			label = "gl-mt300a:usb";
> +			gpios = <&gpio0 7 1>;
> +		};
> +
> +	};
> +
> +	gpio-keys-polled {
> +		compatible = "gpio-keys-polled";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		poll-interval = <20>;
> +		reset {
> +			label = "reset";
> +			gpios = <&gpio0 13 1>;
> +			linux,code = <0x198>;
> +		};
> +
> +		BTN_0 {
> +			label = "BTN_0";
> +			gpios = <&gpio0 1 1>;
> +			linux,code = <0x100>;
> +		};
> +
> +  	    BTN_1 {
> +			label = "BTN_1";
> +			gpios = <&gpio0 2 1>;
> +			linux,code = <0x101>;
> +		};
> + 	};
> +};
> diff --git a/target/linux/ramips/image/Makefile b/target/linux/ramips/image/Makefile
> index e85c574..fb7407b 100644
> --- a/target/linux/ramips/image/Makefile
> +++ b/target/linux/ramips/image/Makefile
> @@ -993,6 +993,7 @@ Image/Build/Profile/RT-N14U=$(call BuildFirmware/Default8M/$(1),$(1),rt-n14u,RT-
>  Image/Build/Profile/WRTNODE=$(call BuildFirmware/Default16M/$(1),$(1),wrtnode,WRTNODE)
>  Image/Build/Profile/WT3020=$(call BuildFirmware/PorayDualSize/$(1),$(1),wt3020,WT3020)
>  Image/Build/Profile/MIWIFI-MINI=$(call BuildFirmware/Default16M/$(1),$(1),miwifi-mini,MIWIFI-MINI)
> +Image/Build/Profile/GL-MT300A=$(call BuildFirmware/Default16M/$(1),$(1),gl-mt300a,GL-MT300A)
>  Image/Build/Profile/ZTE-Q7=$(call BuildFirmware/Default8M/$(1),$(1),zte-q7,ZTE-Q7)
>  Image/Build/Profile/YOUKU-YK1=$(call BuildFirmware/Default16M/$(1),$(1),youku-yk1,YOUKU-YK1)
>  Image/Build/Profile/ZBT-WA05=$(call BuildFirmware/Default8M/$(1),$(1),zbt-wa05,ZBT-WA05)
> @@ -1036,6 +1037,7 @@ define Image/Build/Profile/Default
>  	$(call Image/Build/Profile/WRTNODE,$(1))
>  	$(call Image/Build/Profile/WT3020,$(1))
>  	$(call Image/Build/Profile/MIWIFI-MINI,$(1))
> +	$(call Image/Build/Profile/GL-MT300A,$(1))
>  	$(call Image/Build/Profile/ZTE-Q7,$(1))
>  	$(call Image/Build/Profile/YOUKU-YK1,$(1))
>  	$(call Image/Build/Profile/ZBT-WA05,$(1))
> diff --git a/target/linux/ramips/mt7620/profiles/gli.mk b/target/linux/ramips/mt7620/profiles/gli.mk
> new file mode 100644
> index 0000000..53e2e9d
> --- /dev/null
> +++ b/target/linux/ramips/mt7620/profiles/gli.mk
> @@ -0,0 +1,16 @@
> +#
> +# Copyright (C) 2015 OpenWrt.org
> +#
> +# This is free software, licensed under the GNU General Public License v2.
> +# See /LICENSE for more information.
> +#
> +
> +define Profile/GL-MT300A
> +	NAME:=GL-MT300A 
> +	PACKAGES:=kmod-usb-core kmod-usb-dwc2 kmod-usb2 kmod-usb-ohci kmod-mt76
> +endef
> +
> +define Profile/GL-MT300A/Description
> +	Support for gl-mt300a Router
> +endef
> +$(eval $(call Profile,GL-MT300A))
>