From patchwork Sat Jul 25 23:18:22 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Michael Walle X-Patchwork-Id: 1336393 Return-Path: X-Original-To: incoming@patchwork.ozlabs.org Delivered-To: patchwork-incoming@bilbo.ozlabs.org Authentication-Results: ozlabs.org; spf=pass (sender SPF authorized) smtp.mailfrom=vger.kernel.org (client-ip=23.128.96.18; helo=vger.kernel.org; envelope-from=linux-pwm-owner@vger.kernel.org; receiver=) Authentication-Results: ozlabs.org; dmarc=none (p=none dis=none) header.from=walle.cc Authentication-Results: ozlabs.org; dkim=pass (1024-bit key; secure) header.d=walle.cc header.i=@walle.cc header.a=rsa-sha256 header.s=mail2016061301 header.b=E9ZkxZeD; dkim-atps=neutral Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by ozlabs.org (Postfix) with ESMTP id 4BDhqh3Yd4z9sTn for ; Sun, 26 Jul 2020 09:20:00 +1000 (AEST) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1728014AbgGYXTB (ORCPT ); Sat, 25 Jul 2020 19:19:01 -0400 Received: from ssl.serverraum.org ([176.9.125.105]:43885 "EHLO ssl.serverraum.org" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1727912AbgGYXTA (ORCPT ); Sat, 25 Jul 2020 19:19:00 -0400 Received: from apollo.fritz.box (unknown [IPv6:2a02:810c:c200:2e91:6257:18ff:fec4:ca34]) (using TLSv1.3 with cipher TLS_AES_256_GCM_SHA384 (256/256 bits) key-exchange ECDHE (P-384) server-signature RSA-PSS (2048 bits) server-digest SHA256) (No client certificate requested) by ssl.serverraum.org (Postfix) with ESMTPSA id CB21823E3A; Sun, 26 Jul 2020 01:18:56 +0200 (CEST) DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=walle.cc; s=mail2016061301; t=1595719137; h=from:from:reply-to:subject:subject:date:date:message-id:message-id: to:to:cc:cc:mime-version:mime-version: content-transfer-encoding:content-transfer-encoding: in-reply-to:in-reply-to:references:references; bh=eMQQPwPH6zBMKiAkGJns9PNN/bsW4dSvESSYPM21Euw=; b=E9ZkxZeD4hLfdzP0mF4PvBDAIprw13kqLPvIWlJ2I2jyDDmGLpe4wYdJSAoPy+g1VHh2GK 04vLE2cKhuB3y6Jqusp2/TCxdWsu7URh4leGwAG51CUHs8K5j7YxOMIzLH0Zo8XrpasxHE cH/LHLAfvd2L5jBpIpNBAer/nRjfhkA= From: Michael Walle To: linux-gpio@vger.kernel.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-hwmon@vger.kernel.org, linux-pwm@vger.kernel.org, linux-watchdog@vger.kernel.org, linux-arm-kernel@lists.infradead.org Cc: Linus Walleij , Bartosz Golaszewski , Rob Herring , Jean Delvare , Guenter Roeck , Lee Jones , Thierry Reding , =?utf-8?q?Uwe_Kleine-K=C3=B6nig?= , Wim Van Sebroeck , Shawn Guo , Li Yang , Thomas Gleixner , Jason Cooper , Marc Zyngier , Mark Brown , Greg Kroah-Hartman , Andy Shevchenko , Catalin Marinas , Will Deacon , Pavel Machek , Michael Walle Subject: [PATCH v6 01/13] mfd: add simple regmap based I2C driver Date: Sun, 26 Jul 2020 01:18:22 +0200 Message-Id: <20200725231834.25642-2-michael@walle.cc> X-Mailer: git-send-email 2.20.1 In-Reply-To: <20200725231834.25642-1-michael@walle.cc> References: <20200725231834.25642-1-michael@walle.cc> MIME-Version: 1.0 X-Spam: Yes Sender: linux-pwm-owner@vger.kernel.org Precedence: bulk List-ID: X-Mailing-List: linux-pwm@vger.kernel.org There are I2C devices which contain several different functions but doesn't require any special access functions. For these kind of drivers an I2C regmap should be enough. Create an I2C driver which creates an I2C regmap and enumerates its children. If a device wants to use this as its MFD core driver, it has to add an individual compatible string. It may provide its own regmap configuration. Subdevices can use dev_get_regmap() on the parent to get their regmap instance. Signed-off-by: Michael Walle --- Changes since v5: - removed "select MFD_CORE" in Kconfig - removed help text in Kconfig, we assume that the users of this driver will have a "select MFD_SIMPLE_MFD_I2C". Instead added a small description to the driver itself. - removed "struct simple_mfd_i2c_config" and use regmap_config directly - changed builtin_i2c_driver() to module_i2c_driver(), added MODULE_ boilerplate - cleaned up the included files Changes since v4: - new patch. Lee, please bear with me. I didn't want to delay the new version (where a lot of remarks on the other patches were addressed) even more, just because we haven't figured out how to deal with the MFD part. So for now, I've included this one. drivers/mfd/Kconfig | 5 ++++ drivers/mfd/Makefile | 1 + drivers/mfd/simple-mfd-i2c.c | 55 ++++++++++++++++++++++++++++++++++++ 3 files changed, 61 insertions(+) create mode 100644 drivers/mfd/simple-mfd-i2c.c diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig index 33df0837ab41..c08539c7a166 100644 --- a/drivers/mfd/Kconfig +++ b/drivers/mfd/Kconfig @@ -1162,6 +1162,11 @@ config MFD_SI476X_CORE To compile this driver as a module, choose M here: the module will be called si476x-core. +config MFD_SIMPLE_MFD_I2C + tristate + depends on I2C + select REGMAP_I2C + config MFD_SM501 tristate "Silicon Motion SM501" depends on HAS_DMA diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile index a60e5f835283..78d24a3e7c9e 100644 --- a/drivers/mfd/Makefile +++ b/drivers/mfd/Makefile @@ -264,3 +264,4 @@ obj-$(CONFIG_MFD_STMFX) += stmfx.o obj-$(CONFIG_MFD_KHADAS_MCU) += khadas-mcu.o obj-$(CONFIG_SGI_MFD_IOC3) += ioc3.o +obj-$(CONFIG_MFD_SIMPLE_MFD_I2C) += simple-mfd-i2c.o diff --git a/drivers/mfd/simple-mfd-i2c.c b/drivers/mfd/simple-mfd-i2c.c new file mode 100644 index 000000000000..45090ddad104 --- /dev/null +++ b/drivers/mfd/simple-mfd-i2c.c @@ -0,0 +1,55 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * A very simple I2C MFD driver + * + * The driver enumerates its children and registers a common regmap. Use + * dev_get_regmap(pdev->dev.parent, NULL) in the child nodes to fetch that + * regmap instance. + * + * In the future this driver might be extended to support also other interfaces + * like SPI etc. + */ +#include +#include +#include +#include +#include + +static const struct regmap_config simple_regmap_config = { + .reg_bits = 8, + .val_bits = 8, +}; + +static int simple_mfd_i2c_probe(struct i2c_client *i2c) +{ + const struct regmap_config *config; + struct regmap *regmap; + + config = device_get_match_data(&i2c->dev); + if (!config) + config = &simple_regmap_config; + + regmap = devm_regmap_init_i2c(i2c, config); + if (IS_ERR(regmap)) + return PTR_ERR(regmap); + + return devm_of_platform_populate(&i2c->dev); +} + +static const struct of_device_id simple_mfd_i2c_of_match[] = { + {} +}; +MODULE_DEVICE_TABLE(of, simple_mfd_i2c_of_match); + +static struct i2c_driver simple_mfd_i2c_driver = { + .probe_new = simple_mfd_i2c_probe, + .driver = { + .name = "simple-mfd-i2c", + .of_match_table = simple_mfd_i2c_of_match, + }, +}; +module_i2c_driver(simple_mfd_i2c_driver); + +MODULE_AUTHOR("Michael Walle "); +MODULE_DESCRIPTION("Simple I2C MFD driver"); +MODULE_LICENSE("GPL v2"); From patchwork Sat Jul 25 23:18:23 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Michael Walle X-Patchwork-Id: 1336382 Return-Path: X-Original-To: incoming@patchwork.ozlabs.org Delivered-To: patchwork-incoming@bilbo.ozlabs.org Authentication-Results: ozlabs.org; spf=pass (sender SPF authorized) smtp.mailfrom=vger.kernel.org (client-ip=23.128.96.18; helo=vger.kernel.org; envelope-from=linux-pwm-owner@vger.kernel.org; receiver=) Authentication-Results: ozlabs.org; dmarc=none (p=none dis=none) header.from=walle.cc Authentication-Results: ozlabs.org; dkim=pass (1024-bit key; secure) header.d=walle.cc header.i=@walle.cc header.a=rsa-sha256 header.s=mail2016061301 header.b=Ndc08att; dkim-atps=neutral Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by ozlabs.org (Postfix) with ESMTP id 4BDhqQ2mthz9sSt for ; Sun, 26 Jul 2020 09:19:46 +1000 (AEST) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1728117AbgGYXTF (ORCPT ); Sat, 25 Jul 2020 19:19:05 -0400 Received: from lindbergh.monkeyblade.net ([23.128.96.19]:41304 "EHLO lindbergh.monkeyblade.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1728091AbgGYXTE (ORCPT ); Sat, 25 Jul 2020 19:19:04 -0400 Received: from ssl.serverraum.org (ssl.serverraum.org [IPv6:2a01:4f8:151:8464::1:2]) by lindbergh.monkeyblade.net (Postfix) with ESMTPS id E5FC8C08C5C1; Sat, 25 Jul 2020 16:19:03 -0700 (PDT) Received: from apollo.fritz.box (unknown [IPv6:2a02:810c:c200:2e91:6257:18ff:fec4:ca34]) (using TLSv1.3 with cipher TLS_AES_256_GCM_SHA384 (256/256 bits) key-exchange ECDHE (P-384) server-signature RSA-PSS (2048 bits) server-digest SHA256) (No client certificate requested) by ssl.serverraum.org (Postfix) with ESMTPSA id B611123E3B; Sun, 26 Jul 2020 01:18:57 +0200 (CEST) DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=walle.cc; s=mail2016061301; t=1595719138; h=from:from:reply-to:subject:subject:date:date:message-id:message-id: to:to:cc:cc:mime-version:mime-version: content-transfer-encoding:content-transfer-encoding: in-reply-to:in-reply-to:references:references; bh=F46JDhfwMYpdYufyISnAbaySPEWNpZcKDuHaeq6tFJQ=; b=Ndc08attPdvROUTgCaAXyJcXWuFfNNKsga/cpbdgHH44h3XAvU0Q4tAW4XJ3yZ92DKeFCF 73Ik5RSn5xdRct/X3K7ZUs5YnxFivRmfFffhAlNVHn+Wdet8CkJBn9sjK3AoKktWJU9ECq WN3XF8HpEmJLNyy9bq+WZk6oWmS2G3c= From: Michael Walle To: linux-gpio@vger.kernel.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-hwmon@vger.kernel.org, linux-pwm@vger.kernel.org, linux-watchdog@vger.kernel.org, linux-arm-kernel@lists.infradead.org Cc: Linus Walleij , Bartosz Golaszewski , Rob Herring , Jean Delvare , Guenter Roeck , Lee Jones , Thierry Reding , =?utf-8?q?Uwe_Kleine-K=C3=B6nig?= , Wim Van Sebroeck , Shawn Guo , Li Yang , Thomas Gleixner , Jason Cooper , Marc Zyngier , Mark Brown , Greg Kroah-Hartman , Andy Shevchenko , Catalin Marinas , Will Deacon , Pavel Machek , Michael Walle , Rob Herring Subject: [PATCH v6 02/13] dt-bindings: mfd: Add bindings for sl28cpld Date: Sun, 26 Jul 2020 01:18:23 +0200 Message-Id: <20200725231834.25642-3-michael@walle.cc> X-Mailer: git-send-email 2.20.1 In-Reply-To: <20200725231834.25642-1-michael@walle.cc> References: <20200725231834.25642-1-michael@walle.cc> MIME-Version: 1.0 X-Spam: Yes Sender: linux-pwm-owner@vger.kernel.org Precedence: bulk List-ID: X-Mailing-List: linux-pwm@vger.kernel.org Add a device tree bindings for the board management controller found on the Kontron SMARC-sAL28 board. Signed-off-by: Michael Walle Reviewed-by: Rob Herring --- Changes since v5: - none Changes since v4: - fix the regex of the unit-address Changes since v3: - see cover letter .../bindings/gpio/kontron,sl28cpld-gpio.yaml | 54 +++++++ .../hwmon/kontron,sl28cpld-hwmon.yaml | 27 ++++ .../kontron,sl28cpld-intc.yaml | 54 +++++++ .../bindings/mfd/kontron,sl28cpld.yaml | 153 ++++++++++++++++++ .../bindings/pwm/kontron,sl28cpld-pwm.yaml | 35 ++++ .../watchdog/kontron,sl28cpld-wdt.yaml | 35 ++++ 6 files changed, 358 insertions(+) create mode 100644 Documentation/devicetree/bindings/gpio/kontron,sl28cpld-gpio.yaml create mode 100644 Documentation/devicetree/bindings/hwmon/kontron,sl28cpld-hwmon.yaml create mode 100644 Documentation/devicetree/bindings/interrupt-controller/kontron,sl28cpld-intc.yaml create mode 100644 Documentation/devicetree/bindings/mfd/kontron,sl28cpld.yaml create mode 100644 Documentation/devicetree/bindings/pwm/kontron,sl28cpld-pwm.yaml create mode 100644 Documentation/devicetree/bindings/watchdog/kontron,sl28cpld-wdt.yaml diff --git a/Documentation/devicetree/bindings/gpio/kontron,sl28cpld-gpio.yaml b/Documentation/devicetree/bindings/gpio/kontron,sl28cpld-gpio.yaml new file mode 100644 index 000000000000..9a63a158a796 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/kontron,sl28cpld-gpio.yaml @@ -0,0 +1,54 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/kontron,sl28cpld-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: GPIO driver for the sl28cpld board management controller + +maintainers: + - Michael Walle + +description: | + This module is part of the sl28cpld multi-function device. For more + details see Documentation/devicetree/bindings/mfd/kontron,sl28cpld.yaml. + + There are three flavors of the GPIO controller, one full featured + input/output with interrupt support (kontron,sl28cpld-gpio), one + output-only (kontron,sl28-gpo) and one input-only (kontron,sl28-gpi). + + Each controller supports 8 GPIO lines. + +properties: + compatible: + enum: + - kontron,sl28cpld-gpio + - kontron,sl28cpld-gpi + - kontron,sl28cpld-gpo + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + "#interrupt-cells": + const: 2 + + interrupt-controller: true + + "#gpio-cells": + const: 2 + + gpio-controller: true + + gpio-line-names: + minItems: 1 + maxItems: 8 + +required: + - compatible + - "#gpio-cells" + - gpio-controller + +additionalProperties: false diff --git a/Documentation/devicetree/bindings/hwmon/kontron,sl28cpld-hwmon.yaml b/Documentation/devicetree/bindings/hwmon/kontron,sl28cpld-hwmon.yaml new file mode 100644 index 000000000000..1cebd61c6c32 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/kontron,sl28cpld-hwmon.yaml @@ -0,0 +1,27 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/kontron,sl28cpld-hwmon.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Hardware monitoring driver for the sl28cpld board management controller + +maintainers: + - Michael Walle + +description: | + This module is part of the sl28cpld multi-function device. For more + details see Documentation/devicetree/bindings/mfd/kontron,sl28cpld.yaml. + +properties: + compatible: + enum: + - kontron,sl28cpld-fan + + reg: + maxItems: 1 + +required: + - compatible + +additionalProperties: false diff --git a/Documentation/devicetree/bindings/interrupt-controller/kontron,sl28cpld-intc.yaml b/Documentation/devicetree/bindings/interrupt-controller/kontron,sl28cpld-intc.yaml new file mode 100644 index 000000000000..4c39e9ff9aea --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/kontron,sl28cpld-intc.yaml @@ -0,0 +1,54 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/interrupt-controller/kontron,sl28cpld-intc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Interrupt controller driver for the sl28cpld board management controller + +maintainers: + - Michael Walle + +description: | + This module is part of the sl28cpld multi-function device. For more + details see Documentation/devicetree/bindings/mfd/kontron,sl28cpld.yaml. + + The following interrupts are available. All types and levels are fixed + and handled by the board management controller. + + ==== ============= ================================== + IRQ line/device description + ==== ============= ================================== + 0 RTC_INT# Interrupt line from on-board RTC + 1 SMB_ALERT# Event on SMB_ALERT# line (P1) + 2 ESPI_ALERT0# Event on ESPI_ALERT0# line (S43) + 3 ESPI_ALERT1# Event on ESPI_ALERT1# line (S44) + 4 PWR_BTN# Event on PWR_BTN# line (P128) + 5 SLEEP# Event on SLEEP# line (S149) + 6 watchdog Interrupt of the internal watchdog + 7 n/a not used + ==== ============= ================================== + +properties: + compatible: + enum: + - kontron,sl28cpld-intc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + "#interrupt-cells": + const: 2 + + interrupt-controller: true + +required: + - compatible + - interrupts + - "#interrupt-cells" + - interrupt-controller + +additionalProperties: false diff --git a/Documentation/devicetree/bindings/mfd/kontron,sl28cpld.yaml b/Documentation/devicetree/bindings/mfd/kontron,sl28cpld.yaml new file mode 100644 index 000000000000..e3a62db678e7 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/kontron,sl28cpld.yaml @@ -0,0 +1,153 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/kontron,sl28cpld.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Kontron's sl28cpld board management controller + +maintainers: + - Michael Walle + +description: | + The board management controller may contain different IP blocks like + watchdog, fan monitoring, PWM controller, interrupt controller and a + GPIO controller. + +properties: + compatible: + const: kontron,sl28cpld-r1 + + reg: + description: + I2C device address. + maxItems: 1 + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + "#interrupt-cells": + const: 2 + + interrupts: + maxItems: 1 + + interrupt-controller: true + +patternProperties: + "^gpio(@[0-9a-f]+)?$": + $ref: ../gpio/kontron,sl28cpld-gpio.yaml + + "^hwmon(@[0-9a-f]+)?$": + $ref: ../hwmon/kontron,sl28cpld-hwmon.yaml + + "^interrupt-controller(@[0-9a-f]+)?$": + $ref: ../interrupt-controller/kontron,sl28cpld-intc.yaml + + "^pwm(@[0-9a-f]+)?$": + $ref: ../pwm/kontron,sl28cpld-pwm.yaml + + "^watchdog(@[0-9a-f]+)?$": + $ref: ../watchdog/kontron,sl28cpld-wdt.yaml + +required: + - "#address-cells" + - "#size-cells" + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include + i2c { + #address-cells = <1>; + #size-cells = <0>; + + sl28cpld@4a { + #address-cells = <1>; + #size-cells = <0>; + compatible = "kontron,sl28cpld-r1"; + reg = <0x4a>; + + watchdog@4 { + compatible = "kontron,sl28cpld-wdt"; + reg = <0x4>; + kontron,assert-wdt-timeout-pin; + }; + + hwmon@b { + compatible = "kontron,sl28cpld-fan"; + reg = <0xb>; + }; + + pwm@c { + #pwm-cells = <2>; + compatible = "kontron,sl28cpld-pwm"; + reg = <0xc>; + }; + + pwm@e { + #pwm-cells = <2>; + compatible = "kontron,sl28cpld-pwm"; + reg = <0xe>; + }; + + gpio@10 { + compatible = "kontron,sl28cpld-gpio"; + reg = <0x10>; + interrupts-extended = <&gpio2 6 + IRQ_TYPE_EDGE_FALLING>; + + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = "a", "b", "c"; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio@15 { + compatible = "kontron,sl28cpld-gpio"; + reg = <0x15>; + interrupts-extended = <&gpio2 6 + IRQ_TYPE_EDGE_FALLING>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio@1a { + compatible = "kontron,sl28cpld-gpo"; + reg = <0x1a>; + + gpio-controller; + #gpio-cells = <2>; + }; + + gpio@1b { + compatible = "kontron,sl28cpld-gpi"; + reg = <0x1b>; + + gpio-controller; + #gpio-cells = <2>; + }; + + interrupt-controller@1c { + compatible = "kontron,sl28cpld-intc"; + reg = <0x1c>; + interrupts-extended = <&gpio2 6 + IRQ_TYPE_EDGE_FALLING>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pwm/kontron,sl28cpld-pwm.yaml b/Documentation/devicetree/bindings/pwm/kontron,sl28cpld-pwm.yaml new file mode 100644 index 000000000000..02fe88c30233 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/kontron,sl28cpld-pwm.yaml @@ -0,0 +1,35 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pwm/kontron,sl28cpld-pwm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: PWM driver for the sl28cpld board management controller + +maintainers: + - Michael Walle + +description: | + This module is part of the sl28cpld multi-function device. For more + details see Documentation/devicetree/bindings/mfd/kontron,sl28cpld.yaml. + + The controller supports one PWM channel and supports only four distinct + frequencies (250Hz, 500Hz, 1kHz, 2kHz). + +allOf: + - $ref: pwm.yaml# + +properties: + compatible: + const: kontron,sl28cpld-pwm + + reg: + maxItems: 1 + + "#pwm-cells": + const: 2 + +required: + - compatible + +additionalProperties: false diff --git a/Documentation/devicetree/bindings/watchdog/kontron,sl28cpld-wdt.yaml b/Documentation/devicetree/bindings/watchdog/kontron,sl28cpld-wdt.yaml new file mode 100644 index 000000000000..dd6559f2973a --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/kontron,sl28cpld-wdt.yaml @@ -0,0 +1,35 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/watchdog/kontron,sl28cpld-wdt.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Watchdog driver for the sl28cpld board management controller + +maintainers: + - Michael Walle + +description: | + This module is part of the sl28cpld multi-function device. For more + details see Documentation/devicetree/bindings/mfd/kontron,sl28cpld.yaml. + +allOf: + - $ref: watchdog.yaml# + +properties: + compatible: + const: kontron,sl28cpld-wdt + + reg: + maxItems: 1 + + kontron,assert-wdt-timeout-pin: + description: The SMARC standard defines a WDT_TIME_OUT# pin. If this + property is set, this output will be pulsed when the watchdog bites + and the system resets. + type: boolean + +required: + - compatible + +additionalProperties: false From patchwork Sat Jul 25 23:18:24 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Michael Walle X-Patchwork-Id: 1336367 Return-Path: X-Original-To: incoming@patchwork.ozlabs.org Delivered-To: patchwork-incoming@bilbo.ozlabs.org Authentication-Results: ozlabs.org; spf=pass (sender SPF authorized) smtp.mailfrom=vger.kernel.org (client-ip=23.128.96.18; helo=vger.kernel.org; envelope-from=linux-pwm-owner@vger.kernel.org; receiver=) Authentication-Results: ozlabs.org; dmarc=none (p=none dis=none) header.from=walle.cc Authentication-Results: ozlabs.org; dkim=pass (1024-bit key; secure) header.d=walle.cc header.i=@walle.cc header.a=rsa-sha256 header.s=mail2016061301 header.b=m+Ehso6C; dkim-atps=neutral Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by ozlabs.org (Postfix) with ESMTP id 4BDhq02XnNz9sTC for ; Sun, 26 Jul 2020 09:19:24 +1000 (AEST) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1728062AbgGYXTD (ORCPT ); Sat, 25 Jul 2020 19:19:03 -0400 Received: from ssl.serverraum.org ([176.9.125.105]:55099 "EHLO ssl.serverraum.org" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1727978AbgGYXTC (ORCPT ); Sat, 25 Jul 2020 19:19:02 -0400 Received: from apollo.fritz.box (unknown [IPv6:2a02:810c:c200:2e91:6257:18ff:fec4:ca34]) (using TLSv1.3 with cipher TLS_AES_256_GCM_SHA384 (256/256 bits) key-exchange ECDHE (P-384) server-signature RSA-PSS (2048 bits) server-digest SHA256) (No client certificate requested) by ssl.serverraum.org (Postfix) with ESMTPSA id D78DA23E3F; Sun, 26 Jul 2020 01:18:58 +0200 (CEST) DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=walle.cc; s=mail2016061301; t=1595719139; h=from:from:reply-to:subject:subject:date:date:message-id:message-id: to:to:cc:cc:mime-version:mime-version: content-transfer-encoding:content-transfer-encoding: in-reply-to:in-reply-to:references:references; bh=H2B8ttJ42dTzqVNdmFa3MX4YvKetSzzq/kFHiQy1AgA=; b=m+Ehso6CLT/Ck9ZM3H3xskkzr3b0I/HsSi5C7c8W7/rhwwnKDCS9yUZHTqX1ixQdSkg76Q 7fvdoOusdlfr5U+dmdDTHxrezF70JkOR/v7TiXCFr/5lKUkqzq8+iLzlevnb1ak2ORh+DH CgJW6zUpxsigEGELWzDqEcP/0F+07U8= From: Michael Walle To: linux-gpio@vger.kernel.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-hwmon@vger.kernel.org, linux-pwm@vger.kernel.org, linux-watchdog@vger.kernel.org, linux-arm-kernel@lists.infradead.org Cc: Linus Walleij , Bartosz Golaszewski , Rob Herring , Jean Delvare , Guenter Roeck , Lee Jones , Thierry Reding , =?utf-8?q?Uwe_Kleine-K=C3=B6nig?= , Wim Van Sebroeck , Shawn Guo , Li Yang , Thomas Gleixner , Jason Cooper , Marc Zyngier , Mark Brown , Greg Kroah-Hartman , Andy Shevchenko , Catalin Marinas , Will Deacon , Pavel Machek , Michael Walle Subject: [PATCH v6 03/13] mfd: simple-mfd-i2c: add sl28cpld support Date: Sun, 26 Jul 2020 01:18:24 +0200 Message-Id: <20200725231834.25642-4-michael@walle.cc> X-Mailer: git-send-email 2.20.1 In-Reply-To: <20200725231834.25642-1-michael@walle.cc> References: <20200725231834.25642-1-michael@walle.cc> MIME-Version: 1.0 X-Spam: Yes Sender: linux-pwm-owner@vger.kernel.org Precedence: bulk List-ID: X-Mailing-List: linux-pwm@vger.kernel.org Add the core support for the board management controller found on the SMARC-sAL28 board. At the moment, this controller is used on the Kontron SMARC-sAL28 board. Signed-off-by: Michael Walle --- Changes since v5: - none Changes since v4: - new patch drivers/mfd/simple-mfd-i2c.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/mfd/simple-mfd-i2c.c b/drivers/mfd/simple-mfd-i2c.c index 45090ddad104..dd19abd41d30 100644 --- a/drivers/mfd/simple-mfd-i2c.c +++ b/drivers/mfd/simple-mfd-i2c.c @@ -37,6 +37,7 @@ static int simple_mfd_i2c_probe(struct i2c_client *i2c) } static const struct of_device_id simple_mfd_i2c_of_match[] = { + { .compatible = "kontron,sl28cpld-r1" }, {} }; MODULE_DEVICE_TABLE(of, simple_mfd_i2c_of_match); From patchwork Sat Jul 25 23:18:25 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Michael Walle X-Patchwork-Id: 1336387 Return-Path: X-Original-To: incoming@patchwork.ozlabs.org Delivered-To: patchwork-incoming@bilbo.ozlabs.org Authentication-Results: ozlabs.org; spf=pass (sender SPF authorized) smtp.mailfrom=vger.kernel.org (client-ip=23.128.96.18; helo=vger.kernel.org; envelope-from=linux-pwm-owner@vger.kernel.org; receiver=) Authentication-Results: ozlabs.org; dmarc=none (p=none dis=none) header.from=walle.cc Authentication-Results: ozlabs.org; dkim=pass (1024-bit key; secure) header.d=walle.cc header.i=@walle.cc header.a=rsa-sha256 header.s=mail2016061301 header.b=oRTdPI3r; dkim-atps=neutral Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by ozlabs.org (Postfix) with ESMTP id 4BDhqZ6S0Hz9sRN for ; Sun, 26 Jul 2020 09:19:54 +1000 (AEST) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1728096AbgGYXTE (ORCPT ); Sat, 25 Jul 2020 19:19:04 -0400 Received: from lindbergh.monkeyblade.net ([23.128.96.19]:41302 "EHLO lindbergh.monkeyblade.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1727978AbgGYXTE (ORCPT ); Sat, 25 Jul 2020 19:19:04 -0400 Received: from ssl.serverraum.org (ssl.serverraum.org [IPv6:2a01:4f8:151:8464::1:2]) by lindbergh.monkeyblade.net (Postfix) with ESMTPS id E0191C08C5C0; Sat, 25 Jul 2020 16:19:03 -0700 (PDT) Received: from apollo.fritz.box (unknown [IPv6:2a02:810c:c200:2e91:6257:18ff:fec4:ca34]) (using TLSv1.3 with cipher TLS_AES_256_GCM_SHA384 (256/256 bits) key-exchange ECDHE (P-384) server-signature RSA-PSS (2048 bits) server-digest SHA256) (No client certificate requested) by ssl.serverraum.org (Postfix) with ESMTPSA id 9ECEB23E40; Sun, 26 Jul 2020 01:18:59 +0200 (CEST) DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=walle.cc; s=mail2016061301; t=1595719140; h=from:from:reply-to:subject:subject:date:date:message-id:message-id: to:to:cc:cc:mime-version:mime-version: content-transfer-encoding:content-transfer-encoding: in-reply-to:in-reply-to:references:references; bh=L1UADNJtfY19n1D4ai/YTAoIWOOZ5WFFaX6JGzp/f94=; b=oRTdPI3rCiJrVnCY9/i7z3Qttf37uorwbIVDNQBzi8AZ5zWzAAm+SnRxdkoi46a+PpjPAZ XfxnAGjP9VcTwo8beaYU8jQ4hdIaT0gOFJvphFflOmB3rJCmyq8YdpJLgYYcDMsszys038 yrF+OKIhAGuxKDncj53CtzQ/NDLeERg= From: Michael Walle To: linux-gpio@vger.kernel.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-hwmon@vger.kernel.org, linux-pwm@vger.kernel.org, linux-watchdog@vger.kernel.org, linux-arm-kernel@lists.infradead.org Cc: Linus Walleij , Bartosz Golaszewski , Rob Herring , Jean Delvare , Guenter Roeck , Lee Jones , Thierry Reding , =?utf-8?q?Uwe_Kleine-K=C3=B6nig?= , Wim Van Sebroeck , Shawn Guo , Li Yang , Thomas Gleixner , Jason Cooper , Marc Zyngier , Mark Brown , Greg Kroah-Hartman , Andy Shevchenko , Catalin Marinas , Will Deacon , Pavel Machek , Michael Walle Subject: [PATCH v6 04/13] irqchip: add sl28cpld interrupt controller support Date: Sun, 26 Jul 2020 01:18:25 +0200 Message-Id: <20200725231834.25642-5-michael@walle.cc> X-Mailer: git-send-email 2.20.1 In-Reply-To: <20200725231834.25642-1-michael@walle.cc> References: <20200725231834.25642-1-michael@walle.cc> MIME-Version: 1.0 X-Spam: Yes Sender: linux-pwm-owner@vger.kernel.org Precedence: bulk List-ID: X-Mailing-List: linux-pwm@vger.kernel.org Add support for the interrupt controller inside the sl28 CPLD management controller. The interrupt controller can handle at most 8 interrupts and is really simplistic and consists only of an interrupt mask and an interrupt pending register. Signed-off-by: Michael Walle Acked-by: Marc Zyngier --- Changes since v5: - none Changes since v4: - update copyright year - don't use "int irq" instead of "unsigne int irq", because platform_get_irq() might return a negative error code. Found by "kernel test robot - remove comma in terminator line of the compatible strings list, suggested by Andy - use newer devm_regmap_add_irq_chip_fwnode() - don't use KBUID_MODNAME, suggested by Andy - remove the platform device table Changes since v3: - see cover letter drivers/irqchip/Kconfig | 8 +++ drivers/irqchip/Makefile | 1 + drivers/irqchip/irq-sl28cpld.c | 96 ++++++++++++++++++++++++++++++++++ 3 files changed, 105 insertions(+) create mode 100644 drivers/irqchip/irq-sl28cpld.c diff --git a/drivers/irqchip/Kconfig b/drivers/irqchip/Kconfig index 216b3b8392b5..b23d23eed3a5 100644 --- a/drivers/irqchip/Kconfig +++ b/drivers/irqchip/Kconfig @@ -246,6 +246,14 @@ config RENESAS_RZA1_IRQC Enable support for the Renesas RZ/A1 Interrupt Controller, to use up to 8 external interrupts with configurable sense select. +config SL28CPLD_INTC + bool "Kontron sl28cpld IRQ controller" + select MFD_SIMPLE_MFD_I2C + select REGMAP_IRQ + help + Interrupt controller driver for the board management controller + found on the Kontron sl28 CPLD. + config ST_IRQCHIP bool select REGMAP diff --git a/drivers/irqchip/Makefile b/drivers/irqchip/Makefile index 133f9c45744a..39af7d89204d 100644 --- a/drivers/irqchip/Makefile +++ b/drivers/irqchip/Makefile @@ -111,3 +111,4 @@ obj-$(CONFIG_LOONGSON_HTPIC) += irq-loongson-htpic.o obj-$(CONFIG_LOONGSON_HTVEC) += irq-loongson-htvec.o obj-$(CONFIG_LOONGSON_PCH_PIC) += irq-loongson-pch-pic.o obj-$(CONFIG_LOONGSON_PCH_MSI) += irq-loongson-pch-msi.o +obj-$(CONFIG_SL28CPLD_INTC) += irq-sl28cpld.o diff --git a/drivers/irqchip/irq-sl28cpld.c b/drivers/irqchip/irq-sl28cpld.c new file mode 100644 index 000000000000..0aa50d025ef6 --- /dev/null +++ b/drivers/irqchip/irq-sl28cpld.c @@ -0,0 +1,96 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * sl28cpld interrupt controller driver + * + * Copyright 2020 Kontron Europe GmbH + */ + +#include +#include +#include +#include +#include +#include +#include + +#define INTC_IE 0x00 +#define INTC_IP 0x01 + +static const struct regmap_irq sl28cpld_irqs[] = { + REGMAP_IRQ_REG_LINE(0, 8), + REGMAP_IRQ_REG_LINE(1, 8), + REGMAP_IRQ_REG_LINE(2, 8), + REGMAP_IRQ_REG_LINE(3, 8), + REGMAP_IRQ_REG_LINE(4, 8), + REGMAP_IRQ_REG_LINE(5, 8), + REGMAP_IRQ_REG_LINE(6, 8), + REGMAP_IRQ_REG_LINE(7, 8), +}; + +struct sl28cpld_intc { + struct regmap *regmap; + struct regmap_irq_chip chip; + struct regmap_irq_chip_data *irq_data; +}; + +static int sl28cpld_intc_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct sl28cpld_intc *irqchip; + int irq; + u32 base; + int ret; + + if (!dev->parent) + return -ENODEV; + + irqchip = devm_kzalloc(dev, sizeof(*irqchip), GFP_KERNEL); + if (!irqchip) + return -ENOMEM; + + irqchip->regmap = dev_get_regmap(dev->parent, NULL); + if (!irqchip->regmap) + return -ENODEV; + + irq = platform_get_irq(pdev, 0); + if (irq < 0) + return irq; + + ret = device_property_read_u32(&pdev->dev, "reg", &base); + if (ret) + return -EINVAL; + + irqchip->chip.name = "sl28cpld-intc"; + irqchip->chip.irqs = sl28cpld_irqs; + irqchip->chip.num_irqs = ARRAY_SIZE(sl28cpld_irqs); + irqchip->chip.num_regs = 1; + irqchip->chip.status_base = base + INTC_IP; + irqchip->chip.mask_base = base + INTC_IE; + irqchip->chip.mask_invert = true, + irqchip->chip.ack_base = base + INTC_IP; + + return devm_regmap_add_irq_chip_fwnode(dev, dev_fwnode(dev), + irqchip->regmap, irq, + IRQF_SHARED | IRQF_ONESHOT, 0, + &irqchip->chip, + &irqchip->irq_data); +} + +static const struct of_device_id sl28cpld_intc_of_match[] = { + { .compatible = "kontron,sl28cpld-intc" }, + {} +}; +MODULE_DEVICE_TABLE(of, sl28cpld_intc_of_match); + +static struct platform_driver sl28cpld_intc_driver = { + .probe = sl28cpld_intc_probe, + .driver = { + .name = "sl28cpld-intc", + .of_match_table = sl28cpld_intc_of_match, + } +}; +module_platform_driver(sl28cpld_intc_driver); + +MODULE_DESCRIPTION("sl28cpld Interrupt Controller Driver"); +MODULE_AUTHOR("Michael Walle "); +MODULE_LICENSE("GPL"); From patchwork Sat Jul 25 23:18:26 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Michael Walle X-Patchwork-Id: 1336389 Return-Path: X-Original-To: incoming@patchwork.ozlabs.org Delivered-To: patchwork-incoming@bilbo.ozlabs.org Authentication-Results: ozlabs.org; spf=pass (sender SPF authorized) smtp.mailfrom=vger.kernel.org (client-ip=23.128.96.18; helo=vger.kernel.org; envelope-from=linux-pwm-owner@vger.kernel.org; receiver=) Authentication-Results: ozlabs.org; dmarc=none (p=none dis=none) header.from=walle.cc Authentication-Results: ozlabs.org; dkim=pass (1024-bit key; secure) header.d=walle.cc header.i=@walle.cc header.a=rsa-sha256 header.s=mail2016061301 header.b=C9vhaQ++; dkim-atps=neutral Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by ozlabs.org (Postfix) with ESMTP id 4BDhqc1s7Gz9sRN for ; Sun, 26 Jul 2020 09:19:56 +1000 (AEST) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1727789AbgGYXTx (ORCPT ); Sat, 25 Jul 2020 19:19:53 -0400 Received: from lindbergh.monkeyblade.net ([23.128.96.19]:41306 "EHLO lindbergh.monkeyblade.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1728092AbgGYXTE (ORCPT ); Sat, 25 Jul 2020 19:19:04 -0400 Received: from ssl.serverraum.org (ssl.serverraum.org [IPv6:2a01:4f8:151:8464::1:2]) by lindbergh.monkeyblade.net (Postfix) with ESMTPS id EC044C08C5CE; Sat, 25 Jul 2020 16:19:03 -0700 (PDT) Received: from apollo.fritz.box (unknown [IPv6:2a02:810c:c200:2e91:6257:18ff:fec4:ca34]) (using TLSv1.3 with cipher TLS_AES_256_GCM_SHA384 (256/256 bits) key-exchange ECDHE (P-384) server-signature RSA-PSS (2048 bits) server-digest SHA256) (No client certificate requested) by ssl.serverraum.org (Postfix) with ESMTPSA id 213CF23E42; Sun, 26 Jul 2020 01:19:01 +0200 (CEST) DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=walle.cc; s=mail2016061301; t=1595719142; h=from:from:reply-to:subject:subject:date:date:message-id:message-id: to:to:cc:cc:mime-version:mime-version: content-transfer-encoding:content-transfer-encoding: in-reply-to:in-reply-to:references:references; bh=f9QZpl3KYSoHhNPksCFN8JYkTGbbOAg1wSmhz7xom8k=; b=C9vhaQ++L+qJKTGBKkF+QhiFwo7LwaMNqHcA5WSnTQ+65ploTjOEZsQfh5Y3ZA23BpXVs8 ElwT2mNOtQPav5SsPtoe+2McR0ZHknyZ618S4q3XxkxRx3Y0PPnigTNRvUmb5fBoybJ6Rj oTEsxzUrrtiJ0XxZ8R32a8VVv1JtNjM= From: Michael Walle To: linux-gpio@vger.kernel.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-hwmon@vger.kernel.org, linux-pwm@vger.kernel.org, linux-watchdog@vger.kernel.org, linux-arm-kernel@lists.infradead.org Cc: Linus Walleij , Bartosz Golaszewski , Rob Herring , Jean Delvare , Guenter Roeck , Lee Jones , Thierry Reding , =?utf-8?q?Uwe_Kleine-K=C3=B6nig?= , Wim Van Sebroeck , Shawn Guo , Li Yang , Thomas Gleixner , Jason Cooper , Marc Zyngier , Mark Brown , Greg Kroah-Hartman , Andy Shevchenko , Catalin Marinas , Will Deacon , Pavel Machek , Michael Walle Subject: [PATCH v6 05/13] watchdog: add support for sl28cpld watchdog Date: Sun, 26 Jul 2020 01:18:26 +0200 Message-Id: <20200725231834.25642-6-michael@walle.cc> X-Mailer: git-send-email 2.20.1 In-Reply-To: <20200725231834.25642-1-michael@walle.cc> References: <20200725231834.25642-1-michael@walle.cc> MIME-Version: 1.0 X-Spam: Yes Sender: linux-pwm-owner@vger.kernel.org Precedence: bulk List-ID: X-Mailing-List: linux-pwm@vger.kernel.org Add support for the watchdog of the sl28cpld board management controller. This is part of a multi-function device driver. Signed-off-by: Michael Walle Acked-by: Guenter Roeck --- Changes since v5: - none Changes since v4: - update copyright year - remove #include , suggested by Andy. - slightly reworked the error code handling (only style), suggested by Andy. - Don't use "if (ret < 0)", but only "if (ret)", suggested by Andy. - remove comma in terminator line of the compatible strings list - don't use KBUID_MODNAME - remove the platform device table Changes since v3: - see cover letter drivers/watchdog/Kconfig | 11 ++ drivers/watchdog/Makefile | 1 + drivers/watchdog/sl28cpld_wdt.c | 229 ++++++++++++++++++++++++++++++++ 3 files changed, 241 insertions(+) create mode 100644 drivers/watchdog/sl28cpld_wdt.c diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig index 4f4687c46d38..c4115ea0d3f8 100644 --- a/drivers/watchdog/Kconfig +++ b/drivers/watchdog/Kconfig @@ -340,6 +340,17 @@ config MLX_WDT To compile this driver as a module, choose M here: the module will be called mlx-wdt. +config SL28CPLD_WATCHDOG + tristate "Kontron sl28cpld Watchdog" + select MFD_SIMPLE_MFD_I2C + select WATCHDOG_CORE + help + Say Y here to include support for the watchdog timer + on the Kontron sl28 CPLD. + + To compile this driver as a module, choose M here: the + module will be called sl28cpld_wdt. + # ALPHA Architecture # ARM Architecture diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile index 97bed1d3d97c..aa6e41126901 100644 --- a/drivers/watchdog/Makefile +++ b/drivers/watchdog/Makefile @@ -225,3 +225,4 @@ obj-$(CONFIG_MENF21BMC_WATCHDOG) += menf21bmc_wdt.o obj-$(CONFIG_MENZ069_WATCHDOG) += menz69_wdt.o obj-$(CONFIG_RAVE_SP_WATCHDOG) += rave-sp-wdt.o obj-$(CONFIG_STPMIC1_WATCHDOG) += stpmic1_wdt.o +obj-$(CONFIG_SL28CPLD_WATCHDOG) += sl28cpld_wdt.o diff --git a/drivers/watchdog/sl28cpld_wdt.c b/drivers/watchdog/sl28cpld_wdt.c new file mode 100644 index 000000000000..a45047d8d9ab --- /dev/null +++ b/drivers/watchdog/sl28cpld_wdt.c @@ -0,0 +1,229 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * sl28cpld watchdog driver + * + * Copyright 2020 Kontron Europe GmbH + */ + +#include +#include +#include +#include +#include +#include +#include + +/* + * Watchdog timer block registers. + */ +#define WDT_CTRL 0x00 +#define WDT_CTRL_EN BIT(0) +#define WDT_CTRL_LOCK BIT(2) +#define WDT_CTRL_ASSERT_SYS_RESET BIT(6) +#define WDT_CTRL_ASSERT_WDT_TIMEOUT BIT(7) +#define WDT_TIMEOUT 0x01 +#define WDT_KICK 0x02 +#define WDT_KICK_VALUE 0x6b +#define WDT_COUNT 0x03 + +#define WDT_DEFAULT_TIMEOUT 10 + +static bool nowayout = WATCHDOG_NOWAYOUT; +module_param(nowayout, bool, 0); +MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" + __MODULE_STRING(WATCHDOG_NOWAYOUT) ")"); + +static int timeout; +module_param(timeout, int, 0); +MODULE_PARM_DESC(timeout, "Initial watchdog timeout in seconds"); + +struct sl28cpld_wdt { + struct watchdog_device wdd; + struct regmap *regmap; + u32 offset; + bool assert_wdt_timeout; +}; + +static int sl28cpld_wdt_ping(struct watchdog_device *wdd) +{ + struct sl28cpld_wdt *wdt = watchdog_get_drvdata(wdd); + + return regmap_write(wdt->regmap, wdt->offset + WDT_KICK, + WDT_KICK_VALUE); +} + +static int sl28cpld_wdt_start(struct watchdog_device *wdd) +{ + struct sl28cpld_wdt *wdt = watchdog_get_drvdata(wdd); + unsigned int val; + + val = WDT_CTRL_EN | WDT_CTRL_ASSERT_SYS_RESET; + if (wdt->assert_wdt_timeout) + val |= WDT_CTRL_ASSERT_WDT_TIMEOUT; + if (nowayout) + val |= WDT_CTRL_LOCK; + + return regmap_update_bits(wdt->regmap, wdt->offset + WDT_CTRL, + val, val); +} + +static int sl28cpld_wdt_stop(struct watchdog_device *wdd) +{ + struct sl28cpld_wdt *wdt = watchdog_get_drvdata(wdd); + + return regmap_update_bits(wdt->regmap, wdt->offset + WDT_CTRL, + WDT_CTRL_EN, 0); +} + +static unsigned int sl28cpld_wdt_get_timeleft(struct watchdog_device *wdd) +{ + struct sl28cpld_wdt *wdt = watchdog_get_drvdata(wdd); + unsigned int val; + int ret; + + ret = regmap_read(wdt->regmap, wdt->offset + WDT_COUNT, &val); + if (ret) + return 0; + + return val; +} + +static int sl28cpld_wdt_set_timeout(struct watchdog_device *wdd, + unsigned int timeout) +{ + struct sl28cpld_wdt *wdt = watchdog_get_drvdata(wdd); + int ret; + + ret = regmap_write(wdt->regmap, wdt->offset + WDT_TIMEOUT, timeout); + if (ret) + return ret; + + wdd->timeout = timeout; + + return 0; +} + +static const struct watchdog_info sl28cpld_wdt_info = { + .options = WDIOF_MAGICCLOSE | WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING, + .identity = "sl28cpld watchdog", +}; + +static struct watchdog_ops sl28cpld_wdt_ops = { + .owner = THIS_MODULE, + .start = sl28cpld_wdt_start, + .stop = sl28cpld_wdt_stop, + .ping = sl28cpld_wdt_ping, + .set_timeout = sl28cpld_wdt_set_timeout, + .get_timeleft = sl28cpld_wdt_get_timeleft, +}; + +static int sl28cpld_wdt_probe(struct platform_device *pdev) +{ + struct watchdog_device *wdd; + struct sl28cpld_wdt *wdt; + unsigned int status; + unsigned int val; + int ret; + + if (!pdev->dev.parent) + return -ENODEV; + + wdt = devm_kzalloc(&pdev->dev, sizeof(*wdt), GFP_KERNEL); + if (!wdt) + return -ENOMEM; + + wdt->regmap = dev_get_regmap(pdev->dev.parent, NULL); + if (!wdt->regmap) + return -ENODEV; + + ret = device_property_read_u32(&pdev->dev, "reg", &wdt->offset); + if (ret) + return -EINVAL; + + wdt->assert_wdt_timeout = device_property_read_bool(&pdev->dev, + "kontron,assert-wdt-timeout-pin"); + + /* initialize struct watchdog_device */ + wdd = &wdt->wdd; + wdd->parent = &pdev->dev; + wdd->info = &sl28cpld_wdt_info; + wdd->ops = &sl28cpld_wdt_ops; + wdd->min_timeout = 1; + wdd->max_timeout = 255; + + watchdog_set_drvdata(wdd, wdt); + watchdog_stop_on_reboot(wdd); + + /* + * Read the status early, in case of an error, we haven't modified the + * hardware. + */ + ret = regmap_read(wdt->regmap, wdt->offset + WDT_CTRL, &status); + if (ret) + return ret; + + /* + * Initial timeout value, may be overwritten by device tree or module + * parmeter in watchdog_init_timeout(). + * + * Reading a zero here means that either the hardware has a default + * value of zero (which is very unlikely and definitely a hardware + * bug) or the bootloader set it to zero. In any case, we handle + * this case gracefully and set out own timeout. + */ + ret = regmap_read(wdt->regmap, wdt->offset + WDT_TIMEOUT, &val); + if (ret) + return ret; + + if (val) + wdd->timeout = val; + else + wdd->timeout = WDT_DEFAULT_TIMEOUT; + + watchdog_init_timeout(wdd, timeout, &pdev->dev); + sl28cpld_wdt_set_timeout(wdd, wdd->timeout); + + /* if the watchdog is locked, we set nowayout */ + if (status & WDT_CTRL_LOCK) + nowayout = true; + watchdog_set_nowayout(wdd, nowayout); + + /* + * If watchdog is already running, keep it enabled, but make + * sure its mode is set correctly. + */ + if (status & WDT_CTRL_EN) { + sl28cpld_wdt_start(wdd); + set_bit(WDOG_HW_RUNNING, &wdd->status); + } + + ret = devm_watchdog_register_device(&pdev->dev, wdd); + if (ret < 0) { + dev_err(&pdev->dev, "failed to register watchdog device\n"); + return ret; + } + + dev_info(&pdev->dev, "initial timeout %d sec%s\n", + wdd->timeout, nowayout ? ", nowayout" : ""); + + return 0; +} + +static const struct of_device_id sl28cpld_wdt_of_match[] = { + { .compatible = "kontron,sl28cpld-wdt" }, + {} +}; +MODULE_DEVICE_TABLE(of, sl28cpld_wdt_of_match); + +static struct platform_driver sl28cpld_wdt_driver = { + .probe = sl28cpld_wdt_probe, + .driver = { + .name = "sl28cpld-wdt", + .of_match_table = sl28cpld_wdt_of_match, + }, +}; +module_platform_driver(sl28cpld_wdt_driver); + +MODULE_DESCRIPTION("sl28cpld Watchdog Driver"); +MODULE_AUTHOR("Michael Walle "); +MODULE_LICENSE("GPL"); From patchwork Sat Jul 25 23:18:27 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Michael Walle X-Patchwork-Id: 1336385 Return-Path: X-Original-To: incoming@patchwork.ozlabs.org Delivered-To: patchwork-incoming@bilbo.ozlabs.org Authentication-Results: ozlabs.org; spf=pass (sender SPF authorized) smtp.mailfrom=vger.kernel.org (client-ip=23.128.96.18; helo=vger.kernel.org; envelope-from=linux-pwm-owner@vger.kernel.org; receiver=) Authentication-Results: ozlabs.org; dmarc=none (p=none dis=none) header.from=walle.cc Authentication-Results: ozlabs.org; dkim=pass (1024-bit key; secure) header.d=walle.cc header.i=@walle.cc header.a=rsa-sha256 header.s=mail2016061301 header.b=pmucjxbz; dkim-atps=neutral Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by ozlabs.org (Postfix) with ESMTP id 4BDhqY2Rs4z9sT6 for ; Sun, 26 Jul 2020 09:19:53 +1000 (AEST) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1728144AbgGYXTr (ORCPT ); Sat, 25 Jul 2020 19:19:47 -0400 Received: from lindbergh.monkeyblade.net ([23.128.96.19]:41308 "EHLO lindbergh.monkeyblade.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1728107AbgGYXTF (ORCPT ); Sat, 25 Jul 2020 19:19:05 -0400 Received: from ssl.serverraum.org (ssl.serverraum.org [IPv6:2a01:4f8:151:8464::1:2]) by lindbergh.monkeyblade.net (Postfix) with ESMTPS id 9499CC08C5C0; Sat, 25 Jul 2020 16:19:04 -0700 (PDT) Received: from apollo.fritz.box (unknown [IPv6:2a02:810c:c200:2e91:6257:18ff:fec4:ca34]) (using TLSv1.3 with cipher TLS_AES_256_GCM_SHA384 (256/256 bits) key-exchange ECDHE (P-384) server-signature RSA-PSS (2048 bits) server-digest SHA256) (No client certificate requested) by ssl.serverraum.org (Postfix) with ESMTPSA id 716C823E44; Sun, 26 Jul 2020 01:19:02 +0200 (CEST) DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=walle.cc; s=mail2016061301; t=1595719143; h=from:from:reply-to:subject:subject:date:date:message-id:message-id: to:to:cc:cc:mime-version:mime-version: content-transfer-encoding:content-transfer-encoding: in-reply-to:in-reply-to:references:references; bh=8f+9wMUYIftgWhOFB1JTULU7e/DlL3E7X7hMoc+boKM=; b=pmucjxbz11RDuWUvKHhmJMc5JNC9upNN/Arz6EJ5vpYzm24iMGLgo8NjG3IEbHZDAGg8ew eaTmvyhhuGAO/DsQCB1s24FXPHWj2JBtel4jnxLsDBbD5MSEl0FfeNegsHpOv8bQAYdL2Z gzeRT2Xq9YUrfqOpy6ElYWF1xa1PwKo= From: Michael Walle To: linux-gpio@vger.kernel.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-hwmon@vger.kernel.org, linux-pwm@vger.kernel.org, linux-watchdog@vger.kernel.org, linux-arm-kernel@lists.infradead.org Cc: Linus Walleij , Bartosz Golaszewski , Rob Herring , Jean Delvare , Guenter Roeck , Lee Jones , Thierry Reding , =?utf-8?q?Uwe_Kleine-K=C3=B6nig?= , Wim Van Sebroeck , Shawn Guo , Li Yang , Thomas Gleixner , Jason Cooper , Marc Zyngier , Mark Brown , Greg Kroah-Hartman , Andy Shevchenko , Catalin Marinas , Will Deacon , Pavel Machek , Michael Walle Subject: [PATCH v6 06/13] pwm: add support for sl28cpld PWM controller Date: Sun, 26 Jul 2020 01:18:27 +0200 Message-Id: <20200725231834.25642-7-michael@walle.cc> X-Mailer: git-send-email 2.20.1 In-Reply-To: <20200725231834.25642-1-michael@walle.cc> References: <20200725231834.25642-1-michael@walle.cc> MIME-Version: 1.0 X-Spam: Yes Sender: linux-pwm-owner@vger.kernel.org Precedence: bulk List-ID: X-Mailing-List: linux-pwm@vger.kernel.org Add support for the PWM controller of the sl28cpld board management controller. This is part of a multi-function device driver. The controller has one PWM channel and can just generate four distinct frequencies. Signed-off-by: Michael Walle Acked-by: Thierry Reding --- Changes since v5: - added brief description of the PWM hardware implementation - added hardware limitations - dropped the frequency mode table, instead calculate the prescaler value on the fly. - round the requested parameters instead of support just distinct periods. - prefix the macros by SL28CPLD_ to make them less generic - set polarity to PWM_POLARITY_NORMAL and reject inverted polarity requests. - apply the workaround just for prescaler value of 0. - make errors during probing more verbose Changes since v4: - update copyright year - remove #include , suggested by Andy. - make the pwm mode table look nicer, suggested by Lee. - use dev_get_drvdata(chip->dev) instead of container_of(), suggested by Lee. - use whole sentence in comments, suggested by Lee. - renamed the local "struct sl28cpld_pwm" variable to "priv" everywhere, suggested by Lee. - use pwm_{get,set}_relative_duty_cycle(), suggested by Andy. - make the comment about the 250Hz hardware limitation clearer - don't use "if (ret < 0)", but only "if (ret)", suggested by Andy. - don't use KBUID_MODNAME - remove comma in terminator line of the compatible strings list - remove the platform device table Changes since v3: - see cover letter drivers/pwm/Kconfig | 10 ++ drivers/pwm/Makefile | 1 + drivers/pwm/pwm-sl28cpld.c | 223 +++++++++++++++++++++++++++++++++++++ 3 files changed, 234 insertions(+) create mode 100644 drivers/pwm/pwm-sl28cpld.c diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig index 7dbcf6973d33..a0d50d70c3b9 100644 --- a/drivers/pwm/Kconfig +++ b/drivers/pwm/Kconfig @@ -428,6 +428,16 @@ config PWM_SIFIVE To compile this driver as a module, choose M here: the module will be called pwm-sifive. +config PWM_SL28CPLD + tristate "Kontron sl28cpld PWM support" + select MFD_SIMPLE_MFD_I2C + help + Generic PWM framework driver for board management controller + found on the Kontron sl28 CPLD. + + To compile this driver as a module, choose M here: the module + will be called pwm-sl28cpld. + config PWM_SPEAR tristate "STMicroelectronics SPEAr PWM support" depends on PLAT_SPEAR || COMPILE_TEST diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile index 2c2ba0a03557..cbdcd55d69ee 100644 --- a/drivers/pwm/Makefile +++ b/drivers/pwm/Makefile @@ -40,6 +40,7 @@ obj-$(CONFIG_PWM_RENESAS_TPU) += pwm-renesas-tpu.o obj-$(CONFIG_PWM_ROCKCHIP) += pwm-rockchip.o obj-$(CONFIG_PWM_SAMSUNG) += pwm-samsung.o obj-$(CONFIG_PWM_SIFIVE) += pwm-sifive.o +obj-$(CONFIG_PWM_SL28CPLD) += pwm-sl28cpld.o obj-$(CONFIG_PWM_SPEAR) += pwm-spear.o obj-$(CONFIG_PWM_SPRD) += pwm-sprd.o obj-$(CONFIG_PWM_STI) += pwm-sti.o diff --git a/drivers/pwm/pwm-sl28cpld.c b/drivers/pwm/pwm-sl28cpld.c new file mode 100644 index 000000000000..956fa09f3aba --- /dev/null +++ b/drivers/pwm/pwm-sl28cpld.c @@ -0,0 +1,223 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * sl28cpld PWM driver + * + * Copyright (c) 2020 Michael Walle + * + * There is no public datasheet available for this PWM core. But it is easy + * enough to be briefly explained. It consists of one 8-bit counter. The PWM + * supports four distinct frequencies by selecting when to reset the counter. + * With the prescaler setting you can select which bit of the counter is used + * to reset it. This implies that the higher the frequency the less remaining + * bits are available for the actual counter. + * + * Let cnt[7:0] be the counter, clocked at 32kHz: + * +-----------+--------+--------------+-----------+ + * | prescaler | reset | counter bits | frequency | + * +-----------+--------+--------------+-----------+ + * | 0 | cnt[7] | cnt[6:0] | 250Hz | + * | 1 | cnt[6] | cnt[5:0] | 500Hz | + * | 2 | cnt[5] | cnt[4:0] | 1kHz | + * | 3 | cnt[4] | cnt[3:0] | 2kHz | + * +-----------+--------+--------------+-----------+ + * + * Limitations: + * - The hardware cannot generate a 100% duty cycle if the prescaler is 0. + * - The hardware cannot atomically set the prescaler and the counter value, + * which might lead to glitches and inconsistent states if a write fails. + * - The counter is not reset if you switch the prescaler which leads + * to glitches, too. + * - The duty cycle will switch immediately and not after a complete cycle. + * - Depending on the actual implementation, disabling the PWM might have + * side effects. For example, if the output pin is shared with a GPIO pin + * it will automatically switch back to GPIO mode. + */ + +#include +#include +#include +#include +#include +#include +#include + +/* + * PWM timer block registers. + */ +#define SL28CPLD_PWM_CTRL 0x00 +#define SL28CPLD_PWM_CTRL_ENABLE BIT(7) +#define SL28CPLD_PWM_CTRL_PRESCALER_MASK GENMASK(1, 0) +#define SL28CPLD_PWM_CYCLE 0x01 +#define SL28CPLD_PWM_CYCLE_MAX GENMASK(6, 0) + +#define SL28CPLD_PWM_CLK 32000 /* 32 kHz */ +#define SL28CPLD_PWM_MAX_DUTY_CYCLE(prescaler) (1 << (7 - (prescaler))) +#define SL28CPLD_PWM_PERIOD(prescaler) \ + (NSEC_PER_SEC / SL28CPLD_PWM_CLK * SL28CPLD_PWM_MAX_DUTY_CYCLE(prescaler)) + +/* + * We calculate the duty cycle like this: + * duty_cycle_ns = pwm_cycle_reg * max_period_ns / max_duty_cycle + * + * With + * max_period_ns = (1 << 7 - prescaler) / pwm_clk * NSEC_PER_SEC + * max_duty_cycle = 1 << (7 - prescaler) + * this then simplifies to: + * duty_cycle_ns = pwm_cycle_reg / pwm_clk * NSEC_PER_SEC + */ +#define SL28CPLD_PWM_TO_DUTY_CYCLE(reg) \ + (NSEC_PER_SEC / SL28CPLD_PWM_CLK * (reg)) +#define SL28CPLD_PWM_FROM_DUTY_CYCLE(duty_cycle) \ + (DIV_ROUND_DOWN_ULL((duty_cycle), NSEC_PER_SEC / SL28CPLD_PWM_CLK)) + +struct sl28cpld_pwm { + struct pwm_chip pwm_chip; + struct regmap *regmap; + u32 offset; +}; + +static void sl28cpld_pwm_get_state(struct pwm_chip *chip, + struct pwm_device *pwm, + struct pwm_state *state) +{ + struct sl28cpld_pwm *priv = dev_get_drvdata(chip->dev); + unsigned int reg; + int prescaler; + + regmap_read(priv->regmap, priv->offset + SL28CPLD_PWM_CTRL, ®); + + state->enabled = reg & SL28CPLD_PWM_CTRL_ENABLE; + + prescaler = FIELD_GET(SL28CPLD_PWM_CTRL_PRESCALER_MASK, reg); + state->period = SL28CPLD_PWM_PERIOD(prescaler); + + regmap_read(priv->regmap, priv->offset + SL28CPLD_PWM_CYCLE, ®); + state->duty_cycle = SL28CPLD_PWM_TO_DUTY_CYCLE(reg); + state->polarity = PWM_POLARITY_NORMAL; +} + +static int sl28cpld_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm, + const struct pwm_state *state) +{ + struct sl28cpld_pwm *priv = dev_get_drvdata(chip->dev); + unsigned int cycle, prescaler; + int ret; + u8 ctrl; + + /* Polarity inversion is not supported */ + if (state->polarity != PWM_POLARITY_NORMAL) + return -EINVAL; + + /* + * Calculate the prescaler. Pick the the biggest period that isn't + * bigger than the requested period. + */ + prescaler = DIV_ROUND_UP_ULL(SL28CPLD_PWM_PERIOD(0), state->period); + prescaler = order_base_2(prescaler); + + if (prescaler > field_max(SL28CPLD_PWM_CTRL_PRESCALER_MASK)) + return -ERANGE; + + ctrl = FIELD_PREP(SL28CPLD_PWM_CTRL_PRESCALER_MASK, prescaler); + if (state->enabled) + ctrl |= SL28CPLD_PWM_CTRL_ENABLE; + + cycle = SL28CPLD_PWM_FROM_DUTY_CYCLE(state->duty_cycle); + cycle = min_t(unsigned int, cycle, SL28CPLD_PWM_MAX_DUTY_CYCLE(prescaler)); + + /* + * Work around the hardware limitation. See also above. Trap 100% duty + * cycle if the prescaler is 0. Set prescaler to 1 instead. We don't + * care about the frequency because its "all-one" in either case. + * + * We don't need to check the actual prescaler setting, because only + * if the prescaler is 0 we can have this particular value. + */ + if (cycle == SL28CPLD_PWM_MAX_DUTY_CYCLE(0)) { + ctrl &= ~SL28CPLD_PWM_CTRL_PRESCALER_MASK; + ctrl |= FIELD_PREP(SL28CPLD_PWM_CTRL_PRESCALER_MASK, 1); + cycle = SL28CPLD_PWM_MAX_DUTY_CYCLE(1); + } + + ret = regmap_write(priv->regmap, priv->offset + SL28CPLD_PWM_CTRL, ctrl); + if (ret) + return ret; + + return regmap_write(priv->regmap, priv->offset + SL28CPLD_PWM_CYCLE, (u8)cycle); +} + +static const struct pwm_ops sl28cpld_pwm_ops = { + .apply = sl28cpld_pwm_apply, + .get_state = sl28cpld_pwm_get_state, + .owner = THIS_MODULE, +}; + +static int sl28cpld_pwm_probe(struct platform_device *pdev) +{ + struct sl28cpld_pwm *priv; + struct pwm_chip *chip; + int ret; + + if (!pdev->dev.parent) + return -ENODEV; + + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + priv->regmap = dev_get_regmap(pdev->dev.parent, NULL); + if (!priv->regmap) + return -ENODEV; + + ret = device_property_read_u32(&pdev->dev, "reg", &priv->offset); + if (ret) { + dev_err(&pdev->dev, "no 'reg' property found (%pe)\n", + ERR_PTR(ret)); + return -EINVAL; + } + + /* Initialize the pwm_chip structure */ + chip = &priv->pwm_chip; + chip->dev = &pdev->dev; + chip->ops = &sl28cpld_pwm_ops; + chip->base = -1; + chip->npwm = 1; + + ret = pwmchip_add(&priv->pwm_chip); + if (ret) { + dev_err(&pdev->dev, "failed to add PWM chip (%pe)", + ERR_PTR(ret)); + return ret; + } + + platform_set_drvdata(pdev, priv); + + return 0; +} + +static int sl28cpld_pwm_remove(struct platform_device *pdev) +{ + struct sl28cpld_pwm *priv = platform_get_drvdata(pdev); + + return pwmchip_remove(&priv->pwm_chip); +} + +static const struct of_device_id sl28cpld_pwm_of_match[] = { + { .compatible = "kontron,sl28cpld-pwm" }, + {} +}; +MODULE_DEVICE_TABLE(of, sl28cpld_pwm_of_match); + +static struct platform_driver sl28cpld_pwm_driver = { + .probe = sl28cpld_pwm_probe, + .remove = sl28cpld_pwm_remove, + .driver = { + .name = "sl28cpld-pwm", + .of_match_table = sl28cpld_pwm_of_match, + }, +}; +module_platform_driver(sl28cpld_pwm_driver); + +MODULE_DESCRIPTION("sl28cpld PWM Driver"); +MODULE_AUTHOR("Michael Walle "); +MODULE_LICENSE("GPL"); From patchwork Sat Jul 25 23:18:28 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Michael Walle X-Patchwork-Id: 1336380 Return-Path: X-Original-To: incoming@patchwork.ozlabs.org Delivered-To: patchwork-incoming@bilbo.ozlabs.org Authentication-Results: ozlabs.org; spf=pass (sender SPF authorized) smtp.mailfrom=vger.kernel.org (client-ip=23.128.96.18; helo=vger.kernel.org; envelope-from=linux-pwm-owner@vger.kernel.org; receiver=) Authentication-Results: ozlabs.org; dmarc=none (p=none dis=none) header.from=walle.cc Authentication-Results: ozlabs.org; dkim=pass (1024-bit key; secure) header.d=walle.cc header.i=@walle.cc header.a=rsa-sha256 header.s=mail2016061301 header.b=f3lJRT9y; dkim-atps=neutral Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by ozlabs.org (Postfix) with ESMTP id 4BDhqN5CQjz9sSt for ; Sun, 26 Jul 2020 09:19:44 +1000 (AEST) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1728165AbgGYXTk (ORCPT ); Sat, 25 Jul 2020 19:19:40 -0400 Received: from lindbergh.monkeyblade.net ([23.128.96.19]:41314 "EHLO lindbergh.monkeyblade.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1727978AbgGYXTG (ORCPT ); Sat, 25 Jul 2020 19:19:06 -0400 Received: from ssl.serverraum.org (ssl.serverraum.org [IPv6:2a01:4f8:151:8464::1:2]) by lindbergh.monkeyblade.net (Postfix) with ESMTPS id 8E25EC08C5C0; Sat, 25 Jul 2020 16:19:05 -0700 (PDT) Received: from apollo.fritz.box (unknown [IPv6:2a02:810c:c200:2e91:6257:18ff:fec4:ca34]) (using TLSv1.3 with cipher TLS_AES_256_GCM_SHA384 (256/256 bits) key-exchange ECDHE (P-384) server-signature RSA-PSS (2048 bits) server-digest SHA256) (No client certificate requested) by ssl.serverraum.org (Postfix) with ESMTPSA id 3738023E47; Sun, 26 Jul 2020 01:19:03 +0200 (CEST) DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=walle.cc; s=mail2016061301; t=1595719143; h=from:from:reply-to:subject:subject:date:date:message-id:message-id: to:to:cc:cc:mime-version:mime-version: content-transfer-encoding:content-transfer-encoding: in-reply-to:in-reply-to:references:references; bh=VwTORIMiCBxGdYD+iIPkSH9uNwHN1BDcy9r8ATXHaBw=; b=f3lJRT9yQvPnVESrc19W0H2uTEMQpDg5Cb2jWbyyMel/DIn8tMu+wY+zT05elNyPSryNXw GSkUj3iQfSv+8ZXWKxb1oIG+t9EZE5fu8HEdG3yZf3QwmcHMsjVlVy+x2LLAB5pjqvFCkv K0qihAbyLvf1lp2nhfXMHROqtWaAa2g= From: Michael Walle To: linux-gpio@vger.kernel.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-hwmon@vger.kernel.org, linux-pwm@vger.kernel.org, linux-watchdog@vger.kernel.org, linux-arm-kernel@lists.infradead.org Cc: Linus Walleij , Bartosz Golaszewski , Rob Herring , Jean Delvare , Guenter Roeck , Lee Jones , Thierry Reding , =?utf-8?q?Uwe_Kleine-K=C3=B6nig?= , Wim Van Sebroeck , Shawn Guo , Li Yang , Thomas Gleixner , Jason Cooper , Marc Zyngier , Mark Brown , Greg Kroah-Hartman , Andy Shevchenko , Catalin Marinas , Will Deacon , Pavel Machek , Michael Walle Subject: [PATCH v6 07/13] gpio: add support for the sl28cpld GPIO controller Date: Sun, 26 Jul 2020 01:18:28 +0200 Message-Id: <20200725231834.25642-8-michael@walle.cc> X-Mailer: git-send-email 2.20.1 In-Reply-To: <20200725231834.25642-1-michael@walle.cc> References: <20200725231834.25642-1-michael@walle.cc> MIME-Version: 1.0 X-Spam: Yes Sender: linux-pwm-owner@vger.kernel.org Precedence: bulk List-ID: X-Mailing-List: linux-pwm@vger.kernel.org Add support for the GPIO controller of the sl28 board management controller. This driver is part of a multi-function device. A controller has 8 lines. There are three different flavors: full-featured GPIO with interrupt support, input-only and output-only. Signed-off-by: Michael Walle Reviewed-by: Linus Walleij Reviewed-by: Andy Shevchenko --- Changes since v5: - added "select REGMAP_IRQ" Changes since v4: - update copyright year - remove #include , suggested by Andy. - use device_get_match_data(), suggested by Andy. - drop the irq_support variable, instead call _init_irq() directly, suggested by Andy. - also move the irq code a bit around to make it look nicer - drop "struct sl28cpld_gpio". We don't need to actually store the irq_chip and irq_chip_data, everything is device resource managed. - use 100 chars line limit, suggested by Andy. - remove the platform device table - don't use KBUID_MODNAME Changes since v3: - see cover letter drivers/gpio/Kconfig | 12 +++ drivers/gpio/Makefile | 1 + drivers/gpio/gpio-sl28cpld.c | 161 +++++++++++++++++++++++++++++++++++ 3 files changed, 174 insertions(+) create mode 100644 drivers/gpio/gpio-sl28cpld.c diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig index 8030fd91a3cc..f6a547b76432 100644 --- a/drivers/gpio/Kconfig +++ b/drivers/gpio/Kconfig @@ -1223,6 +1223,18 @@ config GPIO_RC5T583 This driver provides the support for driving/reading the gpio pins of RC5T583 device through standard gpio library. +config GPIO_SL28CPLD + tristate "Kontron sl28cpld GPIO support" + select MFD_SIMPLE_MFD_I2C + select GPIO_REGMAP + select GPIOLIB_IRQCHIP + select REGMAP_IRQ + help + This enables support for the GPIOs found on the Kontron sl28 CPLD. + + This driver can also be built as a module. If so, the module will be + called gpio-sl28cpld. + config GPIO_STMPE bool "STMPE GPIOs" depends on MFD_STMPE diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile index 4f9abff4f2dc..c3a4e7c94a91 100644 --- a/drivers/gpio/Makefile +++ b/drivers/gpio/Makefile @@ -132,6 +132,7 @@ obj-$(CONFIG_GPIO_SCH311X) += gpio-sch311x.o obj-$(CONFIG_GPIO_SCH) += gpio-sch.o obj-$(CONFIG_GPIO_SIFIVE) += gpio-sifive.o obj-$(CONFIG_GPIO_SIOX) += gpio-siox.o +obj-$(CONFIG_GPIO_SL28CPLD) += gpio-sl28cpld.o obj-$(CONFIG_GPIO_SODAVILLE) += gpio-sodaville.o obj-$(CONFIG_GPIO_SPEAR_SPICS) += gpio-spear-spics.o obj-$(CONFIG_GPIO_SPRD) += gpio-sprd.o diff --git a/drivers/gpio/gpio-sl28cpld.c b/drivers/gpio/gpio-sl28cpld.c new file mode 100644 index 000000000000..889b8f5622c2 --- /dev/null +++ b/drivers/gpio/gpio-sl28cpld.c @@ -0,0 +1,161 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * sl28cpld GPIO driver + * + * Copyright 2020 Michael Walle + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* GPIO flavor */ +#define GPIO_REG_DIR 0x00 +#define GPIO_REG_OUT 0x01 +#define GPIO_REG_IN 0x02 +#define GPIO_REG_IE 0x03 +#define GPIO_REG_IP 0x04 + +/* input-only flavor */ +#define GPI_REG_IN 0x00 + +/* output-only flavor */ +#define GPO_REG_OUT 0x00 + +enum sl28cpld_gpio_type { + SL28CPLD_GPIO = 1, + SL28CPLD_GPI, + SL28CPLD_GPO, +}; + +static const struct regmap_irq sl28cpld_gpio_irqs[] = { + REGMAP_IRQ_REG_LINE(0, 8), + REGMAP_IRQ_REG_LINE(1, 8), + REGMAP_IRQ_REG_LINE(2, 8), + REGMAP_IRQ_REG_LINE(3, 8), + REGMAP_IRQ_REG_LINE(4, 8), + REGMAP_IRQ_REG_LINE(5, 8), + REGMAP_IRQ_REG_LINE(6, 8), + REGMAP_IRQ_REG_LINE(7, 8), +}; + +static int sl28cpld_gpio_irq_init(struct platform_device *pdev, + unsigned int base, + struct gpio_regmap_config *config) +{ + struct regmap_irq_chip_data *irq_data; + struct regmap_irq_chip *irq_chip; + struct device *dev = &pdev->dev; + int irq, ret; + + if (!device_property_read_bool(dev, "interrupt-controller")) + return 0; + + irq = platform_get_irq(pdev, 0); + if (irq < 0) + return irq; + + irq_chip = devm_kzalloc(dev, sizeof(*irq_chip), GFP_KERNEL); + if (!irq_chip) + return -ENOMEM; + + irq_chip->name = "sl28cpld-gpio-irq", + irq_chip->irqs = sl28cpld_gpio_irqs; + irq_chip->num_irqs = ARRAY_SIZE(sl28cpld_gpio_irqs); + irq_chip->num_regs = 1; + irq_chip->status_base = base + GPIO_REG_IP; + irq_chip->mask_base = base + GPIO_REG_IE; + irq_chip->mask_invert = true, + irq_chip->ack_base = base + GPIO_REG_IP; + + ret = devm_regmap_add_irq_chip_fwnode(dev, dev_fwnode(dev), + config->regmap, irq, + IRQF_SHARED | IRQF_ONESHOT, + 0, irq_chip, &irq_data); + if (ret) + return ret; + + config->irq_domain = regmap_irq_get_domain(irq_data); + + return 0; +} + +static int sl28cpld_gpio_probe(struct platform_device *pdev) +{ + struct gpio_regmap_config config = {0}; + enum sl28cpld_gpio_type type; + struct regmap *regmap; + u32 base; + int ret; + + if (!pdev->dev.parent) + return -ENODEV; + + type = (uintptr_t)device_get_match_data(&pdev->dev); + if (!type) + return -ENODEV; + + ret = device_property_read_u32(&pdev->dev, "reg", &base); + if (ret) + return -EINVAL; + + regmap = dev_get_regmap(pdev->dev.parent, NULL); + if (!regmap) + return -ENODEV; + + config.regmap = regmap; + config.parent = &pdev->dev; + config.ngpio = 8; + + switch (type) { + case SL28CPLD_GPIO: + config.reg_dat_base = base + GPIO_REG_IN; + config.reg_set_base = base + GPIO_REG_OUT; + /* reg_dir_out_base might be zero */ + config.reg_dir_out_base = GPIO_REGMAP_ADDR(base + GPIO_REG_DIR); + + /* This type supports interrupts */ + ret = sl28cpld_gpio_irq_init(pdev, base, &config); + if (ret) + return ret; + break; + case SL28CPLD_GPO: + config.reg_set_base = base + GPO_REG_OUT; + break; + case SL28CPLD_GPI: + config.reg_dat_base = base + GPI_REG_IN; + break; + default: + dev_err(&pdev->dev, "unknown type %d\n", type); + return -ENODEV; + } + + return PTR_ERR_OR_ZERO(devm_gpio_regmap_register(&pdev->dev, &config)); +} + +static const struct of_device_id sl28cpld_gpio_of_match[] = { + { .compatible = "kontron,sl28cpld-gpio", .data = (void *)SL28CPLD_GPIO }, + { .compatible = "kontron,sl28cpld-gpi", .data = (void *)SL28CPLD_GPI }, + { .compatible = "kontron,sl28cpld-gpo", .data = (void *)SL28CPLD_GPO }, + {} +}; +MODULE_DEVICE_TABLE(of, sl28cpld_gpio_of_match); + +static struct platform_driver sl28cpld_gpio_driver = { + .probe = sl28cpld_gpio_probe, + .driver = { + .name = "sl28cpld-gpio", + .of_match_table = sl28cpld_gpio_of_match, + }, +}; +module_platform_driver(sl28cpld_gpio_driver); + +MODULE_DESCRIPTION("sl28cpld GPIO Driver"); +MODULE_AUTHOR("Michael Walle "); +MODULE_LICENSE("GPL"); From patchwork Sat Jul 25 23:18:29 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Michael Walle X-Patchwork-Id: 1336378 Return-Path: X-Original-To: incoming@patchwork.ozlabs.org Delivered-To: patchwork-incoming@bilbo.ozlabs.org Authentication-Results: ozlabs.org; spf=pass (sender SPF authorized) smtp.mailfrom=vger.kernel.org (client-ip=23.128.96.18; helo=vger.kernel.org; envelope-from=linux-pwm-owner@vger.kernel.org; receiver=) Authentication-Results: ozlabs.org; dmarc=none (p=none dis=none) header.from=walle.cc Authentication-Results: ozlabs.org; dkim=pass (1024-bit key; secure) header.d=walle.cc header.i=@walle.cc header.a=rsa-sha256 header.s=mail2016061301 header.b=fTlr4kkO; dkim-atps=neutral Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by ozlabs.org (Postfix) with ESMTP id 4BDhqJ217bz9sTj for ; Sun, 26 Jul 2020 09:19:40 +1000 (AEST) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1728179AbgGYXTM (ORCPT ); Sat, 25 Jul 2020 19:19:12 -0400 Received: from ssl.serverraum.org ([176.9.125.105]:54055 "EHLO ssl.serverraum.org" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1728130AbgGYXTI (ORCPT ); Sat, 25 Jul 2020 19:19:08 -0400 Received: from apollo.fritz.box (unknown [IPv6:2a02:810c:c200:2e91:6257:18ff:fec4:ca34]) (using TLSv1.3 with cipher TLS_AES_256_GCM_SHA384 (256/256 bits) key-exchange ECDHE (P-384) server-signature RSA-PSS (2048 bits) server-digest SHA256) (No client certificate requested) by ssl.serverraum.org (Postfix) with ESMTPSA id 4BEF223E4A; Sun, 26 Jul 2020 01:19:04 +0200 (CEST) DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=walle.cc; s=mail2016061301; t=1595719144; h=from:from:reply-to:subject:subject:date:date:message-id:message-id: to:to:cc:cc:mime-version:mime-version: content-transfer-encoding:content-transfer-encoding: in-reply-to:in-reply-to:references:references; bh=BfZLy8MiO5laz7HQ0htboEfrjUPoy2Z9vz6+h7eJyrQ=; b=fTlr4kkOYYRL6sLMpCLIk2Q88d0OreRmsYrG9eXkYSrbqFUFnpijYPCShg6oCgzUdWMxwl 8Op3K2l63BZjHgvBtsNLju+3sq76ibNmRIHzTa19/HyeGFuZG4CmXadMBQZzJa45lk40LT 4D3cNw74XpSNVrxKlYqtdzHhalq0srM= From: Michael Walle To: linux-gpio@vger.kernel.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-hwmon@vger.kernel.org, linux-pwm@vger.kernel.org, linux-watchdog@vger.kernel.org, linux-arm-kernel@lists.infradead.org Cc: Linus Walleij , Bartosz Golaszewski , Rob Herring , Jean Delvare , Guenter Roeck , Lee Jones , Thierry Reding , =?utf-8?q?Uwe_Kleine-K=C3=B6nig?= , Wim Van Sebroeck , Shawn Guo , Li Yang , Thomas Gleixner , Jason Cooper , Marc Zyngier , Mark Brown , Greg Kroah-Hartman , Andy Shevchenko , Catalin Marinas , Will Deacon , Pavel Machek , Michael Walle Subject: [PATCH v6 08/13] hwmon: add support for the sl28cpld hardware monitoring controller Date: Sun, 26 Jul 2020 01:18:29 +0200 Message-Id: <20200725231834.25642-9-michael@walle.cc> X-Mailer: git-send-email 2.20.1 In-Reply-To: <20200725231834.25642-1-michael@walle.cc> References: <20200725231834.25642-1-michael@walle.cc> MIME-Version: 1.0 X-Spam: Yes Sender: linux-pwm-owner@vger.kernel.org Precedence: bulk List-ID: X-Mailing-List: linux-pwm@vger.kernel.org Add support for the hardware monitoring controller of the sl28cpld board management controller. This driver is part of a multi-function device. Signed-off-by: Michael Walle Acked-by: Guenter Roeck Reviewed-by: Andy Shevchenko --- Changes since v5: - none Changes since v4: - update copyright year - remove #include , suggested by Andy. - use PTR_ERR_OR_ZERO(), suggested by Andy. - remove the platform device table - don't use KBUID_MODNAME Changes since v3: - see cover letter Documentation/hwmon/index.rst | 1 + Documentation/hwmon/sl28cpld.rst | 36 ++++++++ drivers/hwmon/Kconfig | 10 +++ drivers/hwmon/Makefile | 1 + drivers/hwmon/sl28cpld-hwmon.c | 142 +++++++++++++++++++++++++++++++ 5 files changed, 190 insertions(+) create mode 100644 Documentation/hwmon/sl28cpld.rst create mode 100644 drivers/hwmon/sl28cpld-hwmon.c diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst index 750d3a975d82..d90c43c82936 100644 --- a/Documentation/hwmon/index.rst +++ b/Documentation/hwmon/index.rst @@ -154,6 +154,7 @@ Hardware Monitoring Kernel Drivers sht3x shtc1 sis5595 + sl28cpld smm665 smsc47b397 smsc47m192 diff --git a/Documentation/hwmon/sl28cpld.rst b/Documentation/hwmon/sl28cpld.rst new file mode 100644 index 000000000000..7ed65f78250c --- /dev/null +++ b/Documentation/hwmon/sl28cpld.rst @@ -0,0 +1,36 @@ +.. SPDX-License-Identifier: GPL-2.0-only + +Kernel driver sl28cpld +====================== + +Supported chips: + + * Kontron sl28cpld + + Prefix: 'sl28cpld' + + Datasheet: not available + +Authors: Michael Walle + +Description +----------- + +The sl28cpld is a board management controller which also exposes a hardware +monitoring controller. At the moment this controller supports a single fan +supervisor. In the future there might be other flavours and additional +hardware monitoring might be supported. + +The fan supervisor has a 7 bit counter register and a counter period of 1 +second. If the 7 bit counter overflows, the supervisor will automatically +switch to x8 mode to support a wider input range at the loss of +granularity. + +Sysfs entries +------------- + +The following attributes are supported. + +======================= ======================================================== +fan1_input Fan RPM. Assuming 2 pulses per revolution. +======================= ======================================================== diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig index 8dc28b26916e..a02829ec7386 100644 --- a/drivers/hwmon/Kconfig +++ b/drivers/hwmon/Kconfig @@ -1479,6 +1479,16 @@ config SENSORS_RASPBERRYPI_HWMON This driver can also be built as a module. If so, the module will be called raspberrypi-hwmon. +config SENSORS_SL28CPLD + tristate "Kontron sl28cpld hardware monitoring driver" + select MFD_SIMPLE_MFD_I2C + help + If you say yes here you get support for the fan supervisor of the + sl28cpld board management controller. + + This driver can also be built as a module. If so, the module + will be called sl28cpld-hwmon. + config SENSORS_SHT15 tristate "Sensiron humidity and temperature sensors. SHT15 and compat." depends on GPIOLIB || COMPILE_TEST diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile index a8f4b35b136b..dee8511f9348 100644 --- a/drivers/hwmon/Makefile +++ b/drivers/hwmon/Makefile @@ -159,6 +159,7 @@ obj-$(CONFIG_SENSORS_S3C) += s3c-hwmon.o obj-$(CONFIG_SENSORS_SCH56XX_COMMON)+= sch56xx-common.o obj-$(CONFIG_SENSORS_SCH5627) += sch5627.o obj-$(CONFIG_SENSORS_SCH5636) += sch5636.o +obj-$(CONFIG_SENSORS_SL28CPLD) += sl28cpld-hwmon.o obj-$(CONFIG_SENSORS_SHT15) += sht15.o obj-$(CONFIG_SENSORS_SHT21) += sht21.o obj-$(CONFIG_SENSORS_SHT3x) += sht3x.o diff --git a/drivers/hwmon/sl28cpld-hwmon.c b/drivers/hwmon/sl28cpld-hwmon.c new file mode 100644 index 000000000000..e48f58ec5b9c --- /dev/null +++ b/drivers/hwmon/sl28cpld-hwmon.c @@ -0,0 +1,142 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * sl28cpld hardware monitoring driver + * + * Copyright 2020 Kontron Europe GmbH + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +#define FAN_INPUT 0x00 +#define FAN_SCALE_X8 BIT(7) +#define FAN_VALUE_MASK GENMASK(6, 0) + +struct sl28cpld_hwmon { + struct regmap *regmap; + u32 offset; +}; + +static umode_t sl28cpld_hwmon_is_visible(const void *data, + enum hwmon_sensor_types type, + u32 attr, int channel) +{ + return 0444; +} + +static int sl28cpld_hwmon_read(struct device *dev, + enum hwmon_sensor_types type, u32 attr, + int channel, long *input) +{ + struct sl28cpld_hwmon *hwmon = dev_get_drvdata(dev); + unsigned int value; + int ret; + + switch (attr) { + case hwmon_fan_input: + ret = regmap_read(hwmon->regmap, hwmon->offset + FAN_INPUT, + &value); + if (ret) + return ret; + /* + * The register has a 7 bit value and 1 bit which indicates the + * scale. If the MSB is set, then the lower 7 bit has to be + * multiplied by 8, to get the correct reading. + */ + if (value & FAN_SCALE_X8) + value = FIELD_GET(FAN_VALUE_MASK, value) << 3; + + /* + * The counter period is 1000ms and the sysfs specification + * says we should asssume 2 pulses per revolution. + */ + value *= 60 / 2; + + break; + default: + return -EOPNOTSUPP; + } + + *input = value; + return 0; +} + +static const u32 sl28cpld_hwmon_fan_config[] = { + HWMON_F_INPUT, + 0 +}; + +static const struct hwmon_channel_info sl28cpld_hwmon_fan = { + .type = hwmon_fan, + .config = sl28cpld_hwmon_fan_config, +}; + +static const struct hwmon_channel_info *sl28cpld_hwmon_info[] = { + &sl28cpld_hwmon_fan, + NULL +}; + +static const struct hwmon_ops sl28cpld_hwmon_ops = { + .is_visible = sl28cpld_hwmon_is_visible, + .read = sl28cpld_hwmon_read, +}; + +static const struct hwmon_chip_info sl28cpld_hwmon_chip_info = { + .ops = &sl28cpld_hwmon_ops, + .info = sl28cpld_hwmon_info, +}; + +static int sl28cpld_hwmon_probe(struct platform_device *pdev) +{ + struct sl28cpld_hwmon *hwmon; + struct device *hwmon_dev; + int ret; + + if (!pdev->dev.parent) + return -ENODEV; + + hwmon = devm_kzalloc(&pdev->dev, sizeof(*hwmon), GFP_KERNEL); + if (!hwmon) + return -ENOMEM; + + hwmon->regmap = dev_get_regmap(pdev->dev.parent, NULL); + if (!hwmon->regmap) + return -ENODEV; + + ret = device_property_read_u32(&pdev->dev, "reg", &hwmon->offset); + if (ret) + return -EINVAL; + + hwmon_dev = devm_hwmon_device_register_with_info(&pdev->dev, + "sl28cpld_hwmon", hwmon, + &sl28cpld_hwmon_chip_info, NULL); + if (IS_ERR(hwmon_dev)) + dev_err(&pdev->dev, "failed to register as hwmon device"); + + return PTR_ERR_OR_ZERO(hwmon_dev); +} + +static const struct of_device_id sl28cpld_hwmon_of_match[] = { + { .compatible = "kontron,sl28cpld-fan" }, + {} +}; +MODULE_DEVICE_TABLE(of, sl28cpld_hwmon_of_match); + +static struct platform_driver sl28cpld_hwmon_driver = { + .probe = sl28cpld_hwmon_probe, + .driver = { + .name = "sl28cpld-fan", + .of_match_table = sl28cpld_hwmon_of_match, + }, +}; +module_platform_driver(sl28cpld_hwmon_driver); + +MODULE_DESCRIPTION("sl28cpld Hardware Monitoring Driver"); +MODULE_AUTHOR("Michael Walle "); +MODULE_LICENSE("GPL"); From patchwork Sat Jul 25 23:18:30 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Michael Walle X-Patchwork-Id: 1336379 Return-Path: X-Original-To: incoming@patchwork.ozlabs.org Delivered-To: patchwork-incoming@bilbo.ozlabs.org Authentication-Results: ozlabs.org; spf=pass (sender SPF authorized) smtp.mailfrom=vger.kernel.org (client-ip=23.128.96.18; helo=vger.kernel.org; envelope-from=linux-pwm-owner@vger.kernel.org; receiver=) Authentication-Results: ozlabs.org; dmarc=none (p=none dis=none) header.from=walle.cc Authentication-Results: ozlabs.org; dkim=pass (1024-bit key; secure) header.d=walle.cc header.i=@walle.cc header.a=rsa-sha256 header.s=mail2016061301 header.b=kqEGlrmP; dkim-atps=neutral Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by ozlabs.org (Postfix) with ESMTP id 4BDhqK3853z9sTn for ; Sun, 26 Jul 2020 09:19:41 +1000 (AEST) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1728174AbgGYXTL (ORCPT ); Sat, 25 Jul 2020 19:19:11 -0400 Received: from ssl.serverraum.org ([176.9.125.105]:37695 "EHLO ssl.serverraum.org" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1728158AbgGYXTI (ORCPT ); Sat, 25 Jul 2020 19:19:08 -0400 Received: from apollo.fritz.box (unknown [IPv6:2a02:810c:c200:2e91:6257:18ff:fec4:ca34]) (using TLSv1.3 with cipher TLS_AES_256_GCM_SHA384 (256/256 bits) key-exchange ECDHE (P-384) server-signature RSA-PSS (2048 bits) server-digest SHA256) (No client certificate requested) by ssl.serverraum.org (Postfix) with ESMTPSA id 10FBE23E4C; Sun, 26 Jul 2020 01:19:05 +0200 (CEST) DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=walle.cc; s=mail2016061301; t=1595719145; h=from:from:reply-to:subject:subject:date:date:message-id:message-id: to:to:cc:cc:mime-version:mime-version: content-transfer-encoding:content-transfer-encoding: in-reply-to:in-reply-to:references:references; bh=9ai0La+0NTz47zNKNe8eCNR0aOanRg5MZY86cm9G5UM=; b=kqEGlrmPMMmvf5UYnEWCX7xD16NalVyHm8iD2CKx6Y+VwWk2EGFCxx+7e2BzfsxBTFTocT xKhT9AwybYVF9eTawp2dkCoEjLAYb9sPdI7mKhh5f5Hp5Tr+Nz3FtcRvrdnqlecrAVjUCY XGTnkTsDPcSANAkKEr4FbAPcv5Jttyc= From: Michael Walle To: linux-gpio@vger.kernel.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-hwmon@vger.kernel.org, linux-pwm@vger.kernel.org, linux-watchdog@vger.kernel.org, linux-arm-kernel@lists.infradead.org Cc: Linus Walleij , Bartosz Golaszewski , Rob Herring , Jean Delvare , Guenter Roeck , Lee Jones , Thierry Reding , =?utf-8?q?Uwe_Kleine-K=C3=B6nig?= , Wim Van Sebroeck , Shawn Guo , Li Yang , Thomas Gleixner , Jason Cooper , Marc Zyngier , Mark Brown , Greg Kroah-Hartman , Andy Shevchenko , Catalin Marinas , Will Deacon , Pavel Machek , Michael Walle Subject: [PATCH v6 09/13] arm64: dts: freescale: sl28: enable sl28cpld Date: Sun, 26 Jul 2020 01:18:30 +0200 Message-Id: <20200725231834.25642-10-michael@walle.cc> X-Mailer: git-send-email 2.20.1 In-Reply-To: <20200725231834.25642-1-michael@walle.cc> References: <20200725231834.25642-1-michael@walle.cc> MIME-Version: 1.0 X-Spam: Yes Sender: linux-pwm-owner@vger.kernel.org Precedence: bulk List-ID: X-Mailing-List: linux-pwm@vger.kernel.org Add the board management controller node. Signed-off-by: Michael Walle --- Changes since v5: - none Changes since v4: - none Changes since v3: - see cover letter .../freescale/fsl-ls1028a-kontron-sl28.dts | 102 ++++++++++++++++++ 1 file changed, 102 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28.dts index 360b3a168c10..8712fe82727b 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28.dts @@ -8,6 +8,7 @@ /dts-v1/; #include "fsl-ls1028a.dtsi" +#include / { model = "Kontron SMARC-sAL28"; @@ -170,6 +171,107 @@ reg = <0x32>; }; + sl28cpld@4a { + #address-cells = <1>; + #size-cells = <0>; + compatible = "kontron,sl28cpld-r1"; + reg = <0x4a>; + + watchdog@4 { + compatible = "kontron,sl28cpld-wdt"; + reg = <0x4>; + kontron,assert-wdt-timeout-pin; + }; + + hwmon@b { + compatible = "kontron,sl28cpld-fan"; + reg = <0xb>; + }; + + sl28cpld_pwm0: pwm@c { + #pwm-cells = <2>; + compatible = "kontron,sl28cpld-pwm"; + reg = <0xc>; + }; + + sl28cpld_pwm1: pwm@e { + #pwm-cells = <2>; + compatible = "kontron,sl28cpld-pwm"; + reg = <0xe>; + }; + + sl28cpld_gpio0: gpio@10 { + compatible = "kontron,sl28cpld-gpio"; + reg = <0x10>; + interrupts-extended = <&gpio2 6 + IRQ_TYPE_EDGE_FALLING>; + + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = + "GPIO0_CAM0_PWR_N", "GPIO1_CAM1_PWR_N", + "GPIO2_CAM0_RST_N", "GPIO3_CAM1_RST_N", + "GPIO4_HDA_RST_N", "GPIO5_PWM_OUT", + "GPIO6_TACHIN", "GPIO7"; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + sl28cpld_gpio1: gpio@15 { + compatible = "kontron,sl28cpld-gpio"; + reg = <0x15>; + interrupts-extended = <&gpio2 6 + IRQ_TYPE_EDGE_FALLING>; + + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = + "GPIO8", "GPIO9", "GPIO10", "GPIO11", + "", "", "", ""; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + sl28cpld_gpio2: gpio@1a { + compatible = "kontron,sl28cpld-gpo"; + reg = <0x1a>; + + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = + "LCD0 voltage enable", + "LCD0 backlight enable", + "eMMC reset", "LVDS bridge reset", + "LVDS bridge power-down", + "SDIO power enable", + "", ""; + }; + + sl28cpld_gpio3: gpio@1b { + compatible = "kontron,sl28cpld-gpi"; + reg = <0x1b>; + + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = + "Power button", "Force recovery", "Sleep", + "Battery low", "Lid state", "Charging", + "Charger present", ""; + }; + + sl28cpld_intc: interrupt-controller@1c { + compatible = "kontron,sl28cpld-intc"; + reg = <0x1c>; + interrupts-extended = <&gpio2 6 + IRQ_TYPE_EDGE_FALLING>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + eeprom@50 { compatible = "atmel,24c32"; reg = <0x50>; From patchwork Sat Jul 25 23:18:31 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Michael Walle X-Patchwork-Id: 1336375 Return-Path: X-Original-To: incoming@patchwork.ozlabs.org Delivered-To: patchwork-incoming@bilbo.ozlabs.org Authentication-Results: ozlabs.org; spf=pass (sender SPF authorized) smtp.mailfrom=vger.kernel.org (client-ip=23.128.96.18; helo=vger.kernel.org; envelope-from=linux-pwm-owner@vger.kernel.org; receiver=) Authentication-Results: ozlabs.org; dmarc=none (p=none dis=none) header.from=walle.cc Authentication-Results: ozlabs.org; dkim=pass (1024-bit key; secure) header.d=walle.cc header.i=@walle.cc header.a=rsa-sha256 header.s=mail2016061301 header.b=frlgzOeJ; dkim-atps=neutral Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by ozlabs.org (Postfix) with ESMTP id 4BDhqG0XDqz9sSt for ; Sun, 26 Jul 2020 09:19:38 +1000 (AEST) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1728195AbgGYXTN (ORCPT ); Sat, 25 Jul 2020 19:19:13 -0400 Received: from ssl.serverraum.org ([176.9.125.105]:37405 "EHLO ssl.serverraum.org" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1728155AbgGYXTJ (ORCPT ); Sat, 25 Jul 2020 19:19:09 -0400 Received: from apollo.fritz.box (unknown [IPv6:2a02:810c:c200:2e91:6257:18ff:fec4:ca34]) (using TLSv1.3 with cipher TLS_AES_256_GCM_SHA384 (256/256 bits) key-exchange ECDHE (P-384) server-signature RSA-PSS (2048 bits) server-digest SHA256) (No client certificate requested) by ssl.serverraum.org (Postfix) with ESMTPSA id F0E6823E4D; Sun, 26 Jul 2020 01:19:05 +0200 (CEST) DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=walle.cc; s=mail2016061301; t=1595719146; h=from:from:reply-to:subject:subject:date:date:message-id:message-id: to:to:cc:cc:mime-version:mime-version: content-transfer-encoding:content-transfer-encoding: in-reply-to:in-reply-to:references:references; bh=EzYqQ9RsAteBsFVLbk29ft1E2vQYeteOFHnfkivX47M=; b=frlgzOeJfwdhNBvZK1NRTVkvJHyYvYi/Fi49V9HZ1R/fjErEVd3Z250m3HSHWAZZ8uyBoD S/hUOf8kdGOb6X3EYX2qWAKuLpa8zia3uifj7D1IQDkH/KUO1tPZyx9QTbRFOkqbvXTxz2 3rtIK8y2wCV160gsFPWjmy39EG9xoPA= From: Michael Walle To: linux-gpio@vger.kernel.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-hwmon@vger.kernel.org, linux-pwm@vger.kernel.org, linux-watchdog@vger.kernel.org, linux-arm-kernel@lists.infradead.org Cc: Linus Walleij , Bartosz Golaszewski , Rob Herring , Jean Delvare , Guenter Roeck , Lee Jones , Thierry Reding , =?utf-8?q?Uwe_Kleine-K=C3=B6nig?= , Wim Van Sebroeck , Shawn Guo , Li Yang , Thomas Gleixner , Jason Cooper , Marc Zyngier , Mark Brown , Greg Kroah-Hartman , Andy Shevchenko , Catalin Marinas , Will Deacon , Pavel Machek , Michael Walle Subject: [PATCH v6 10/13] arm64: dts: freescale: sl28: map GPIOs to input events Date: Sun, 26 Jul 2020 01:18:31 +0200 Message-Id: <20200725231834.25642-11-michael@walle.cc> X-Mailer: git-send-email 2.20.1 In-Reply-To: <20200725231834.25642-1-michael@walle.cc> References: <20200725231834.25642-1-michael@walle.cc> MIME-Version: 1.0 X-Spam: Yes Sender: linux-pwm-owner@vger.kernel.org Precedence: bulk List-ID: X-Mailing-List: linux-pwm@vger.kernel.org Now that we have support for GPIO lines of the SMARC connector, map the sleep, power and lid switch signals to the corresponding keys using the gpio-keys and gpio-keys-polled drivers. The power and sleep signals have dedicated interrupts, thus we use these ones. The lid switch is just mapped to a GPIO input and needs polling. Signed-off-by: Michael Walle --- Changes since v5: - none Changes since v4: - none Changes since v3: - see cover letter .../freescale/fsl-ls1028a-kontron-sl28.dts | 32 +++++++++++++++++++ 1 file changed, 32 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28.dts index 8712fe82727b..c4fd99efdbba 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28.dts @@ -9,6 +9,8 @@ /dts-v1/; #include "fsl-ls1028a.dtsi" #include +#include +#include / { model = "Kontron SMARC-sAL28"; @@ -23,6 +25,36 @@ spi1 = &dspi2; }; + buttons0 { + compatible = "gpio-keys"; + + power-button { + interrupts-extended = <&sl28cpld_intc + 4 IRQ_TYPE_EDGE_BOTH>; + linux,code = ; + label = "Power"; + }; + + sleep-button { + interrupts-extended = <&sl28cpld_intc + 5 IRQ_TYPE_EDGE_BOTH>; + linux,code = ; + label = "Sleep"; + }; + }; + + buttons1 { + compatible = "gpio-keys-polled"; + poll-interval = <200>; + + lid-switch { + linux,input-type = ; + linux,code = ; + gpios = <&sl28cpld_gpio3 4 GPIO_ACTIVE_LOW>; + label = "Lid"; + }; + }; + chosen { stdout-path = "serial0:115200n8"; }; From patchwork Sat Jul 25 23:18:32 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Michael Walle X-Patchwork-Id: 1336376 Return-Path: X-Original-To: incoming@patchwork.ozlabs.org Delivered-To: patchwork-incoming@bilbo.ozlabs.org Authentication-Results: ozlabs.org; spf=pass (sender SPF authorized) smtp.mailfrom=vger.kernel.org (client-ip=23.128.96.18; helo=vger.kernel.org; envelope-from=linux-pwm-owner@vger.kernel.org; receiver=) Authentication-Results: ozlabs.org; dmarc=none (p=none dis=none) header.from=walle.cc Authentication-Results: ozlabs.org; dkim=pass (1024-bit key; secure) header.d=walle.cc header.i=@walle.cc header.a=rsa-sha256 header.s=mail2016061301 header.b=DayADKKr; dkim-atps=neutral Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by ozlabs.org (Postfix) with ESMTP id 4BDhqG5yhrz9sTh for ; Sun, 26 Jul 2020 09:19:38 +1000 (AEST) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1728188AbgGYXTM (ORCPT ); Sat, 25 Jul 2020 19:19:12 -0400 Received: from lindbergh.monkeyblade.net ([23.128.96.19]:41326 "EHLO lindbergh.monkeyblade.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1728091AbgGYXTJ (ORCPT ); Sat, 25 Jul 2020 19:19:09 -0400 Received: from ssl.serverraum.org (ssl.serverraum.org [IPv6:2a01:4f8:151:8464::1:2]) by lindbergh.monkeyblade.net (Postfix) with ESMTPS id 1C95CC08C5C0; Sat, 25 Jul 2020 16:19:09 -0700 (PDT) Received: from apollo.fritz.box (unknown [IPv6:2a02:810c:c200:2e91:6257:18ff:fec4:ca34]) (using TLSv1.3 with cipher TLS_AES_256_GCM_SHA384 (256/256 bits) key-exchange ECDHE (P-384) server-signature RSA-PSS (2048 bits) server-digest SHA256) (No client certificate requested) by ssl.serverraum.org (Postfix) with ESMTPSA id BFBDA23E4E; Sun, 26 Jul 2020 01:19:06 +0200 (CEST) DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=walle.cc; s=mail2016061301; t=1595719147; h=from:from:reply-to:subject:subject:date:date:message-id:message-id: to:to:cc:cc:mime-version:mime-version: content-transfer-encoding:content-transfer-encoding: in-reply-to:in-reply-to:references:references; bh=x7yHRk0PxQh2un749jI6/AvKt0OkpMZsL/WSj3mhMYk=; b=DayADKKrqj7htUQNGjYNMzg0Y+8NfoTdprdnJVoWefQxQboWar4AADJ8xmlLAooYXBxeXq cDSzwdcfnfoZSfCxZ14Uixx0BEFtip2imK6YAyNNoAYB+h8D1vgPcQcgFHPH3i9Q0Jb5MX kAbO1gi25jz+5z5EDUQk6E2UB8UGtFQ= From: Michael Walle To: linux-gpio@vger.kernel.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-hwmon@vger.kernel.org, linux-pwm@vger.kernel.org, linux-watchdog@vger.kernel.org, linux-arm-kernel@lists.infradead.org Cc: Linus Walleij , Bartosz Golaszewski , Rob Herring , Jean Delvare , Guenter Roeck , Lee Jones , Thierry Reding , =?utf-8?q?Uwe_Kleine-K=C3=B6nig?= , Wim Van Sebroeck , Shawn Guo , Li Yang , Thomas Gleixner , Jason Cooper , Marc Zyngier , Mark Brown , Greg Kroah-Hartman , Andy Shevchenko , Catalin Marinas , Will Deacon , Pavel Machek , Michael Walle Subject: [PATCH v6 11/13] arm64: dts: freescale: sl28: enable LED support Date: Sun, 26 Jul 2020 01:18:32 +0200 Message-Id: <20200725231834.25642-12-michael@walle.cc> X-Mailer: git-send-email 2.20.1 In-Reply-To: <20200725231834.25642-1-michael@walle.cc> References: <20200725231834.25642-1-michael@walle.cc> MIME-Version: 1.0 X-Spam: Yes Sender: linux-pwm-owner@vger.kernel.org Precedence: bulk List-ID: X-Mailing-List: linux-pwm@vger.kernel.org Now that we have support for GPIO lines of the SMARC connector, enable LED support on the KBox A-230-LS. There are two LEDs without fixed functions, one is yellow and one is green. Unfortunately, it is just one multi-color LED, thus while it is possible to enable both at the same time it is hard to tell the difference between "yellow only" and "yellow and green". Signed-off-by: Michael Walle --- Changes since v5: - changed the label, suggested by Pavel Machek Changes since v4: - none Changes since v3: - see cover letter .../fsl-ls1028a-kontron-kbox-a-230-ls.dts | 14 ++++++++++++++ 1 file changed, 14 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-kbox-a-230-ls.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-kbox-a-230-ls.dts index 4b4cc6a1573d..8e5e289ce04f 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-kbox-a-230-ls.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-kbox-a-230-ls.dts @@ -16,6 +16,20 @@ model = "Kontron KBox A-230-LS"; compatible = "kontron,kbox-a-230-ls", "kontron,sl28-var4", "kontron,sl28", "fsl,ls1028a"; + + leds { + compatible = "gpio-leds"; + + alarm-led { + label = "yellow:alarm"; + gpios = <&sl28cpld_gpio0 0 0>; + }; + + power-led { + label = "green:power"; + gpios = <&sl28cpld_gpio1 3 0>; + }; + }; }; &enetc_mdio_pf3 { From patchwork Sat Jul 25 23:18:33 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Michael Walle X-Patchwork-Id: 1336373 Return-Path: X-Original-To: incoming@patchwork.ozlabs.org Delivered-To: patchwork-incoming@bilbo.ozlabs.org Authentication-Results: ozlabs.org; spf=pass (sender SPF authorized) smtp.mailfrom=vger.kernel.org (client-ip=23.128.96.18; helo=vger.kernel.org; envelope-from=linux-pwm-owner@vger.kernel.org; receiver=) Authentication-Results: ozlabs.org; dmarc=none (p=none dis=none) header.from=walle.cc Authentication-Results: ozlabs.org; dkim=pass (1024-bit key; secure) header.d=walle.cc header.i=@walle.cc header.a=rsa-sha256 header.s=mail2016061301 header.b=FqK7F8Mp; dkim-atps=neutral Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by ozlabs.org (Postfix) with ESMTP id 4BDhqF2FQdz9sTh for ; Sun, 26 Jul 2020 09:19:37 +1000 (AEST) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1728203AbgGYXTN (ORCPT ); Sat, 25 Jul 2020 19:19:13 -0400 Received: from lindbergh.monkeyblade.net ([23.128.96.19]:41330 "EHLO lindbergh.monkeyblade.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1728163AbgGYXTK (ORCPT ); Sat, 25 Jul 2020 19:19:10 -0400 Received: from ssl.serverraum.org (ssl.serverraum.org [IPv6:2a01:4f8:151:8464::1:2]) by lindbergh.monkeyblade.net (Postfix) with ESMTPS id D3F48C08C5C1; Sat, 25 Jul 2020 16:19:09 -0700 (PDT) Received: from apollo.fritz.box (unknown [IPv6:2a02:810c:c200:2e91:6257:18ff:fec4:ca34]) (using TLSv1.3 with cipher TLS_AES_256_GCM_SHA384 (256/256 bits) key-exchange ECDHE (P-384) server-signature RSA-PSS (2048 bits) server-digest SHA256) (No client certificate requested) by ssl.serverraum.org (Postfix) with ESMTPSA id C084B23E53; Sun, 26 Jul 2020 01:19:07 +0200 (CEST) DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=walle.cc; s=mail2016061301; t=1595719148; h=from:from:reply-to:subject:subject:date:date:message-id:message-id: to:to:cc:cc:mime-version:mime-version: content-transfer-encoding:content-transfer-encoding: in-reply-to:in-reply-to:references:references; bh=RjfyPR+ssvRgrVnJMlguZW/zuOoVr8Ka15azPuH7R4I=; b=FqK7F8MpLfUDppxNTcmWokmQJ+fjYfZMJxsbd2LPbxFKr59M4e6V7/aHW5EDy6djKV4ygv KbM/JrguYK9D57MtB7+/ll+xbNp+QGcQ5X3m0uY4K3RfNqrrW6QUXDR0Lxj9WKYK66OwiA nVqDjKeuTEPsInNZintnu5v0S5hvttI= From: Michael Walle To: linux-gpio@vger.kernel.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-hwmon@vger.kernel.org, linux-pwm@vger.kernel.org, linux-watchdog@vger.kernel.org, linux-arm-kernel@lists.infradead.org Cc: Linus Walleij , Bartosz Golaszewski , Rob Herring , Jean Delvare , Guenter Roeck , Lee Jones , Thierry Reding , =?utf-8?q?Uwe_Kleine-K=C3=B6nig?= , Wim Van Sebroeck , Shawn Guo , Li Yang , Thomas Gleixner , Jason Cooper , Marc Zyngier , Mark Brown , Greg Kroah-Hartman , Andy Shevchenko , Catalin Marinas , Will Deacon , Pavel Machek , Michael Walle Subject: [PATCH v6 12/13] arm64: dts: freescale: sl28: enable fan support Date: Sun, 26 Jul 2020 01:18:33 +0200 Message-Id: <20200725231834.25642-13-michael@walle.cc> X-Mailer: git-send-email 2.20.1 In-Reply-To: <20200725231834.25642-1-michael@walle.cc> References: <20200725231834.25642-1-michael@walle.cc> MIME-Version: 1.0 X-Spam: Yes Sender: linux-pwm-owner@vger.kernel.org Precedence: bulk List-ID: X-Mailing-List: linux-pwm@vger.kernel.org Add a pwm-fan mapped to the PWM channel 0 which is connected to the fan connector of the carrier. Signed-off-by: Michael Walle --- Changes since v5: - none Changes since v4: - none Changes since v3: - see cover letter .../dts/freescale/fsl-ls1028a-kontron-sl28-var3-ads2.dts | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var3-ads2.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var3-ads2.dts index 0973a6a45217..c45d7b40e374 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var3-ads2.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var3-ads2.dts @@ -15,6 +15,15 @@ compatible = "kontron,sl28-var3-ads2", "kontron,sl28-var3", "kontron,sl28", "fsl,ls1028a"; + pwm-fan { + compatible = "pwm-fan"; + cooling-min-state = <0>; + cooling-max-state = <3>; + #cooling-cells = <2>; + pwms = <&sl28cpld_pwm0 0 4000000>; + cooling-levels = <1 128 192 255>; + }; + sound { #address-cells = <1>; #size-cells = <0>; From patchwork Sat Jul 25 23:18:34 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Michael Walle X-Patchwork-Id: 1336371 Return-Path: X-Original-To: incoming@patchwork.ozlabs.org Delivered-To: patchwork-incoming@bilbo.ozlabs.org Authentication-Results: ozlabs.org; spf=pass (sender SPF authorized) smtp.mailfrom=vger.kernel.org (client-ip=23.128.96.18; helo=vger.kernel.org; envelope-from=linux-pwm-owner@vger.kernel.org; receiver=) Authentication-Results: ozlabs.org; dmarc=none (p=none dis=none) header.from=walle.cc Authentication-Results: ozlabs.org; dkim=pass (1024-bit key; secure) header.d=walle.cc header.i=@walle.cc header.a=rsa-sha256 header.s=mail2016061301 header.b=kBVLkIEP; dkim-atps=neutral Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by ozlabs.org (Postfix) with ESMTP id 4BDhq74rjRz9sSn for ; Sun, 26 Jul 2020 09:19:31 +1000 (AEST) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1728213AbgGYXTO (ORCPT ); Sat, 25 Jul 2020 19:19:14 -0400 Received: from lindbergh.monkeyblade.net ([23.128.96.19]:41332 "EHLO lindbergh.monkeyblade.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1728165AbgGYXTK (ORCPT ); Sat, 25 Jul 2020 19:19:10 -0400 Received: from ssl.serverraum.org (ssl.serverraum.org [IPv6:2a01:4f8:151:8464::1:2]) by lindbergh.monkeyblade.net (Postfix) with ESMTPS id 980EAC08C5CE; Sat, 25 Jul 2020 16:19:10 -0700 (PDT) Received: from apollo.fritz.box (unknown [IPv6:2a02:810c:c200:2e91:6257:18ff:fec4:ca34]) (using TLSv1.3 with cipher TLS_AES_256_GCM_SHA384 (256/256 bits) key-exchange ECDHE (P-384) server-signature RSA-PSS (2048 bits) server-digest SHA256) (No client certificate requested) by ssl.serverraum.org (Postfix) with ESMTPSA id 7C23B23E55; Sun, 26 Jul 2020 01:19:08 +0200 (CEST) DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=walle.cc; s=mail2016061301; t=1595719149; h=from:from:reply-to:subject:subject:date:date:message-id:message-id: to:to:cc:cc:mime-version:mime-version: content-transfer-encoding:content-transfer-encoding: in-reply-to:in-reply-to:references:references; bh=PNc2RG8Tt+EkQg/L/MGAMSEh8dcuaImVAHmm6o6jhBo=; b=kBVLkIEP/C2ReoLMyukzWmgQonAia/PsYLqogFg5iMR5wqlp5oiy3e4/jE9FCMUs+CI+iZ 9sq5luyHjrUqugUIRSqr00X1nFrqOMPqukhSU4mAxlWwGGzbsPqqVg12Y+lEyMH34kOrlS A2WaSgaF6BMMipDcQPTQFKHffbMnw+g= From: Michael Walle To: linux-gpio@vger.kernel.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-hwmon@vger.kernel.org, linux-pwm@vger.kernel.org, linux-watchdog@vger.kernel.org, linux-arm-kernel@lists.infradead.org Cc: Linus Walleij , Bartosz Golaszewski , Rob Herring , Jean Delvare , Guenter Roeck , Lee Jones , Thierry Reding , =?utf-8?q?Uwe_Kleine-K=C3=B6nig?= , Wim Van Sebroeck , Shawn Guo , Li Yang , Thomas Gleixner , Jason Cooper , Marc Zyngier , Mark Brown , Greg Kroah-Hartman , Andy Shevchenko , Catalin Marinas , Will Deacon , Pavel Machek , Michael Walle Subject: [PATCH v6 13/13] arm64: defconfig: enable the sl28cpld board management controller Date: Sun, 26 Jul 2020 01:18:34 +0200 Message-Id: <20200725231834.25642-14-michael@walle.cc> X-Mailer: git-send-email 2.20.1 In-Reply-To: <20200725231834.25642-1-michael@walle.cc> References: <20200725231834.25642-1-michael@walle.cc> MIME-Version: 1.0 X-Spam: Yes Sender: linux-pwm-owner@vger.kernel.org Precedence: bulk List-ID: X-Mailing-List: linux-pwm@vger.kernel.org Enable the kernel modules for the board management controller "sl28cpld" which is used on the SMARC-sAL28 board. Signed-off-by: Michael Walle --- Changes since v5: - new patch arch/arm64/configs/defconfig | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig index e0f33826819f..d45a33ccf7d7 100644 --- a/arch/arm64/configs/defconfig +++ b/arch/arm64/configs/defconfig @@ -500,6 +500,7 @@ CONFIG_GPIO_PCA953X=y CONFIG_GPIO_PCA953X_IRQ=y CONFIG_GPIO_BD9571MWV=m CONFIG_GPIO_MAX77620=y +CONFIG_GPIO_SL28CPLD=m CONFIG_POWER_AVS=y CONFIG_QCOM_CPR=y CONFIG_ROCKCHIP_IODOMAIN=y @@ -513,6 +514,7 @@ CONFIG_SENSORS_ARM_SCPI=y CONFIG_SENSORS_LM90=m CONFIG_SENSORS_PWM_FAN=m CONFIG_SENSORS_RASPBERRYPI_HWMON=m +CONFIG_SENSORS_SL28CPLD=m CONFIG_SENSORS_INA2XX=m CONFIG_SENSORS_INA3221=m CONFIG_THERMAL_GOV_POWER_ALLOCATOR=y @@ -535,6 +537,7 @@ CONFIG_QCOM_TSENS=y CONFIG_QCOM_SPMI_TEMP_ALARM=m CONFIG_UNIPHIER_THERMAL=y CONFIG_WATCHDOG=y +CONFIG_SL28CPLD_WATCHDOG=m CONFIG_ARM_SP805_WATCHDOG=y CONFIG_ARM_SBSA_WATCHDOG=y CONFIG_ARM_SMC_WATCHDOG=y @@ -934,8 +937,10 @@ CONFIG_PWM_MESON=m CONFIG_PWM_RCAR=m CONFIG_PWM_ROCKCHIP=y CONFIG_PWM_SAMSUNG=y +CONFIG_PWM_SL28CPLD=m CONFIG_PWM_SUN4I=m CONFIG_PWM_TEGRA=m +CONFIG_SL28CPLD_INTC=y CONFIG_QCOM_PDC=y CONFIG_RESET_QCOM_AOSS=y CONFIG_RESET_QCOM_PDC=m