diff mbox series

[17/42] dt-bindings: exynos: Update bindings doc for DW MMC controller

Message ID 20240522233135.26835-18-semen.protsenko@linaro.org
State Changes Requested
Delegated to: Jaehoon Chung
Headers show
Series mmc: dw_mmc: Enable eMMC on E850-96 board | expand

Commit Message

Sam Protsenko May 22, 2024, 11:31 p.m. UTC
Update the bindings doc for Exynos DW MMC block to follow the upstream
example and reflect the latest changes made in corresponding Linux
kernel bindings.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
---
 doc/device-tree-bindings/exynos/dwmmc.txt | 46 +++++++++++++----------
 1 file changed, 27 insertions(+), 19 deletions(-)
diff mbox series

Patch

diff --git a/doc/device-tree-bindings/exynos/dwmmc.txt b/doc/device-tree-bindings/exynos/dwmmc.txt
index 694d1959162c..d90792be8599 100644
--- a/doc/device-tree-bindings/exynos/dwmmc.txt
+++ b/doc/device-tree-bindings/exynos/dwmmc.txt
@@ -12,7 +12,9 @@  SOC specific and Board specific properties are channel specific.
 Required SoC Specific Properties:
 
 - compatible: should be
-	- samsung,exynos-dwmmc: for exynos platforms
+	- samsung,exynos4412-dw-mshc: for Exynos4 platforms
+	- samsung,exynos-dwmmc: for Exynos5 platforms
+	- samsung,exynos7-dw-mshc-smu: for Exynos7 platforms (with SMU block)
 
 - reg: physical base address of the controller and length of memory mapped
 	region.
@@ -23,32 +25,38 @@  Required Board Specific Properties:
 
 - #address-cells: should be 1.
 - #size-cells: should be 0.
-- samsung,bus-width: The width of the bus used to interface the devices
+- bus-width: The width of the bus used to interface the devices
 	supported by DWC_mobile_storage (SD-MMC/EMMC/SDIO).
 	. Typically the bus width is 4 or 8.
-- samsung,timing: The timing values to be written into the
-	Drv/sample clock selection register of corresponding channel.
-	. It is comprised of 3 values corresponding to the 3 fileds
-	  'SelClk_sample', 'SelClk_drv' and 'DIVRATIO' of CLKSEL register.
-	. SelClk_sample: Select sample clock among 8 shifted clocks.
-	. SelClk_drv: Select drv clock among 8 shifted clocks.
-	. DIVRATIO: Clock Divide ratio select.
-	. The above 3 values are used by the clock phase shifter.
+- samsung,dw-mshc-ciu-div: The divider value for the card interface unit (ciu)
+	clock (0..7).
+- samsung,dw-mshc-sdr-timing: The timing values for single data rate (SDR) mode
+	operation.
+	. First value is CIU clock phase shift value for TX mode (0..7).
+	. Second value is CIU clock phase shift value for RX mode (0..7).
+- samsung,dw-mshc-ddr-timing: The timing values for double data rate (DDR) mode
+	operation. If missing, values from samsung,dw-mshc-sdr-timing are used.
+	. First value is CIU clock phase shift value for TX mode (0..7).
+	. Second value is CIU clock phase shift value for RX mode (0..7).
 
 Example:
 
 mmc@12200000 {
-	samsung,bus-width = <8>;
-	samsung,timing = <1 3 3>;
-	samsung,removable = <1>;
-}
+	bus-width = <8>;
+	non-removable;
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-sdr-timing = <1 3>;
+	samsung,dw-mshc-ddr-timing = <0 2>;
+};
+
 In the above example,
 	. The bus width is 8
-	. Timing is comprised of 3 values as explained below
+	. Divider value for CLKSEL register is 3. The CIU clock rate will be
+	  calculated as SDCLKIN / (3 + 1).
+	. SDR and DDR timings are comprised of 2 values as explained below
 		1 - SelClk_sample
 		3 - SelClk_drv
-		3 - DIVRATIO
-	. The 'removable' flag indicates whether the the particilar device
+	. The 'non-removable' flag indicates whether the particular device
 	  cannot be removed (always present) or it is a removable device.
-		1 - Indicates that the device is removable.
-		0 - Indicates that the device cannot be removed.
+		Flag is present - Indicates that the device cannot be removed.
+		Flag is not present - Indicates that the device is removable.