@@ -223,20 +223,20 @@
<GIC_SPI 212 IRQ_TYPE_EDGE_RISING>,
<GIC_SPI 213 IRQ_TYPE_EDGE_RISING>;
interrupt-names = "tgia0", "tgib0", "tgic0", "tgid0",
- "tgiv0", "tgie0", "tgif0",
- "tgia1", "tgib1", "tgiv1", "tgiu1",
- "tgia2", "tgib2", "tgiv2", "tgiu2",
+ "tciv0", "tgie0", "tgif0",
+ "tgia1", "tgib1", "tciv1", "tciu1",
+ "tgia2", "tgib2", "tciv2", "tciu2",
"tgia3", "tgib3", "tgic3", "tgid3",
- "tgiv3",
+ "tciv3",
"tgia4", "tgib4", "tgic4", "tgid4",
- "tgiv4",
+ "tciv4",
"tgiu5", "tgiv5", "tgiw5",
"tgia6", "tgib6", "tgic6", "tgid6",
- "tgiv6",
+ "tciv6",
"tgia7", "tgib7", "tgic7", "tgid7",
- "tgiv7",
+ "tciv7",
"tgia8", "tgib8", "tgic8", "tgid8",
- "tgiv8", "tgiu8";
+ "tciv8", "tciu8";
clocks = <&cpg CPG_MOD R9A07G044_MTU_X_MCK_MTU3>;
power-domains = <&cpg>;
resets = <&cpg R9A07G044_MTU_X_PRESET_MTU3>;
@@ -6,6 +6,27 @@
*/
/dts-v1/;
+
+/* Enable SCIF2 (SER0) on PMOD1 (CN7) */
+#define PMOD1_SER0 1
+
+/*
+ * To enable MTU3a PWM on PMOD0,
+ * Disable PMOD1_SER0 by setting "#define PMOD1_SER0 0" above and
+ * enable PMOD_MTU3 by setting "#define PMOD_MTU3 1" below.
+ */
+#define PMOD_MTU3 0
+
+#if (PMOD_MTU3 && PMOD1_SER0)
+#error "Cannot set as PMOD_MTU3 and PMOD1_SER0 are mutually exclusive "
+#endif
+
+#define MTU3_COUNTER_Z_PHASE_SIGNAL 0
+
+#if (!PMOD_MTU3 && MTU3_COUNTER_Z_PHASE_SIGNAL)
+#error "Cannot set 1 to MTU3_COUNTER_Z_PHASE_SIGNAL as PMOD_MTU3=0"
+#endif
+
#include "r9a07g044l2.dtsi"
#include "rzg2l-smarc-som.dtsi"
#include "rzg2l-smarc-pinfunction.dtsi"
@@ -32,12 +32,6 @@
stdout-path = "serial0:115200n8";
};
- audio_mclock: audio_mclock {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <11289600>;
- };
-
snd_rzg2l: sound {
compatible = "simple-audio-card";
simple-audio-card,format = "i2s";
@@ -55,7 +49,7 @@
};
codec_dai: simple-audio-card,codec {
- clocks = <&audio_mclock>;
+ clocks = <&versa3 2>;
sound-dai = <&wm8978>;
};
};
@@ -76,13 +70,19 @@
gpios-states = <1>;
states = <3300000 1>, <1800000 0>;
};
+
+ x1: x1-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24000000>;
+ };
};
-&audio_clk1{
+&audio_clk1 {
clock-frequency = <11289600>;
};
-&audio_clk2{
+&audio_clk2 {
clock-frequency = <12288000>;
};
@@ -53,6 +53,26 @@
<RZG2L_PORT_PINMUX(18, 1, 3)>; /* SCL */
};
+ mtu3_pins: mtu3 {
+ mtu3-ext-clk-input-pin {
+ pinmux = <RZG2L_PORT_PINMUX(48, 0, 4)>, /* MTCLKA */
+ <RZG2L_PORT_PINMUX(48, 1, 4)>; /* MTCLKB */
+ };
+
+ mtu3-pwm {
+ pinmux = <RZG2L_PORT_PINMUX(44, 0, 4)>, /* MTIOC3A */
+ <RZG2L_PORT_PINMUX(44, 1, 4)>, /* MTIOC3B */
+ <RZG2L_PORT_PINMUX(44, 2, 4)>, /* MTIOC3C */
+ <RZG2L_PORT_PINMUX(44, 3, 4)>; /* MTIOC3D */
+ };
+
+#if MTU3_COUNTER_Z_PHASE_SIGNAL
+ mtu3-zphase-clk {
+ pinmux = <RZG2L_PORT_PINMUX(19, 0, 3)>; /* MTIOC1A */
+ };
+#endif /* MTU3_COUNTER_Z_PHASE_SIGNAL */
+ };
+
scif0_pins: scif0 {
pinmux = <RZG2L_PORT_PINMUX(38, 0, 1)>, /* TxD */
<RZG2L_PORT_PINMUX(38, 1, 1)>; /* RxD */
@@ -73,6 +73,13 @@
gpios = <&pinctrl RZG2L_GPIO(39, 0) GPIO_ACTIVE_HIGH>;
regulator-always-on;
};
+
+ /* 32.768kHz crystal */
+ x2: x2-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ };
};
&adc {
@@ -100,7 +107,7 @@
rxc-skew-psec = <2400>;
txc-skew-psec = <2400>;
rxdv-skew-psec = <0>;
- txdv-skew-psec = <0>;
+ txen-skew-psec = <0>;
rxd0-skew-psec = <0>;
rxd1-skew-psec = <0>;
rxd2-skew-psec = <0>;
@@ -128,7 +135,7 @@
rxc-skew-psec = <2400>;
txc-skew-psec = <2400>;
rxdv-skew-psec = <0>;
- txdv-skew-psec = <0>;
+ txen-skew-psec = <0>;
rxd0-skew-psec = <0>;
rxd1-skew-psec = <0>;
rxd2-skew-psec = <0>;
@@ -148,6 +155,17 @@
mali-supply = <®_1p1v>;
};
+&i2c3 {
+ raa215300: pmic@12 {
+ compatible = "renesas,raa215300";
+ reg = <0x12>, <0x6f>;
+ reg-names = "main", "rtc";
+
+ clocks = <&x2>;
+ clock-names = "xin";
+ };
+};
+
&ostm1 {
status = "okay";
};
@@ -8,9 +8,6 @@
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
-/* comment the #define statement to disable SCIF2 (SER0) on PMOD1 (CN7) */
-#define PMOD1_SER0 1
-
/ {
aliases {
serial1 = &scif2;
@@ -113,8 +110,48 @@
#sound-dai-cells = <0>;
reg = <0x1a>;
};
+
+ versa3: clock-generator@68 {
+ compatible = "renesas,5p35023";
+ reg = <0x68>;
+ #clock-cells = <1>;
+ clocks = <&x1>;
+
+ renesas,settings = [
+ 80 00 11 19 4c 02 23 7f 83 19 08 a9 5f 25 24 bf
+ 00 14 7a e1 00 00 00 00 01 55 59 bb 3f 30 90 b6
+ 80 b0 45 c4 95
+ ];
+
+ assigned-clocks = <&versa3 0>, <&versa3 1>,
+ <&versa3 2>, <&versa3 3>,
+ <&versa3 4>, <&versa3 5>;
+ assigned-clock-rates = <24000000>, <11289600>,
+ <11289600>, <12000000>,
+ <25000000>, <12288000>;
+ };
};
+#if PMOD_MTU3
+&mtu3 {
+ pinctrl-0 = <&mtu3_pins>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+#if MTU3_COUNTER_Z_PHASE_SIGNAL
+/* SDHI cd pin is muxed with counter Z phase signal */
+&sdhi1 {
+ status = "disabled";
+};
+#endif /* MTU3_COUNTER_Z_PHASE_SIGNAL */
+
+&spi1 {
+ status = "disabled";
+};
+#endif /* PMOD_MTU3 */
+
/*
* To enable SCIF2 (SER0) on PMOD1 (CN7)
* SW1 should be at position 2->3 so that SER0_CTS# line is activated