@@ -169,7 +169,8 @@ dtb-$(CONFIG_ROCKCHIP_RK3568) += \
rk3566-anbernic-rgxx3.dtb \
rk3566-radxa-cm3-io.dtb \
rk3568-evb.dtb \
- rk3568-rock-3a.dtb
+ rk3568-rock-3a.dtb \
+ rk3568-lubancat-2.dtb
dtb-$(CONFIG_ROCKCHIP_RK3588) += \
rk3588-edgeble-neu6a-io.dtb \
new file mode 100644
@@ -0,0 +1,87 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2023 Rockchip Electronics Co., Ltd
+ * (C) Copyright 2023 Andy Yan <andyshrk@163.com>
+ */
+
+#include "rk356x-u-boot.dtsi"
+
+/ {
+ chosen {
+ stdout-path = &uart2;
+ };
+};
+
+&emmc_bus8 {
+ bootph-all;
+};
+
+&emmc_clk {
+ bootph-all;
+};
+
+&emmc_cmd {
+ bootph-all;
+};
+
+&emmc_datastrobe {
+ bootph-all;
+};
+
+&pinctrl {
+ bootph-all;
+};
+
+&pcfg_pull_none {
+ bootph-all;
+};
+
+&pcfg_pull_up_drv_level_2 {
+ bootph-all;
+};
+
+&pcfg_pull_up {
+ bootph-all;
+};
+
+&sdmmc0_bus4 {
+ bootph-all;
+};
+
+&sdmmc0_clk {
+ bootph-all;
+};
+
+&sdmmc0_cmd {
+ bootph-all;
+};
+
+&sdmmc0_det {
+ bootph-all;
+};
+
+&sdhci {
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
+ mmc-hs400-enhanced-strobe;
+};
+
+&sdmmc2 {
+ status = "disabled";
+};
+
+&uart1 {
+ status = "disabled";
+};
+
+&uart2m0_xfer {
+ bootph-all;
+};
+
+&uart2 {
+ clock-frequency = <24000000>;
+ bootph-all;
+ status = "okay";
+};
new file mode 100644
@@ -0,0 +1,734 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/*
+ * Copyright (c) 2023 Rockchip Electronics Co., Ltd.
+ * Copyright (c) 2023 EmbedFire <embedfire@embedfire.com>
+ * Copyright (c) 2023 Andy Yan <andyshrk@163.com>
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3568.dtsi"
+
+/ {
+ model = "EmbedFire LubanCat 2";
+ compatible = "embedfire,lubancat-2", "rockchip,rk3568";
+
+ aliases {
+ ethernet0 = &gmac0;
+ ethernet1 = &gmac1;
+ mmc0 = &sdmmc0;
+ mmc1 = &sdhci;
+ };
+
+ chosen: chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ user_led: user-led {
+ label = "user_led";
+ linux,default-trigger = "heartbeat";
+ default-state = "on";
+ gpios = <&gpio0 RK_PC7 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&user_led_pin>;
+ };
+ };
+
+ hdmi-con {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ dc_5v: dc-5v-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "dc_5v";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ vcc3v3_sys: vcc3v3-sys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc5v0_sys: vcc5v0-sys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&dc_5v>;
+ };
+
+ vcc3v3_m2_pcie: vcc3v3-m2-pcie-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "m2_pcie_3v3";
+ enable-active-high;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&vcc3v3_m2_pcie_en>;
+ pinctrl-names = "default";
+ startup-delay-us = <200000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc3v3_mini_pcie: vcc3v3-mini-pcie-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "minipcie_3v3";
+ enable-active-high;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 RK_PC3 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&vcc3v3_mini_pcie_en>;
+ pinctrl-names = "default";
+ startup-delay-us = <5000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc5v0_usb20_host: vcc5v0-usb20-host-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_usb20_host";
+ enable-active-high;
+ gpio = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&vcc5v0_usb20_host_en>;
+ pinctrl-names = "default";
+ };
+
+ vcc5v0_usb30_host: vcc5v0-usb30-host-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_usb30_host";
+ enable-active-high;
+ gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&vcc5v0_usb30_host_en>;
+ pinctrl-names = "default";
+ };
+
+ vcc5v0_otg_vbus: vcc5v0-otg-vbus-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_otg_vbus";
+ enable-active-high;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio0 RK_PD3 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&vcc5v0_otg_vbus_en>;
+ pinctrl-names = "default";
+ };
+};
+
+&combphy0 {
+ status = "okay";
+};
+
+&combphy1 {
+ status = "okay";
+};
+
+&combphy2 {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu>;
+ status = "okay";
+};
+
+&hdmi {
+ avdd-0v9-supply = <&vdda0v9_image>;
+ avdd-1v8-supply = <&vcca1v8_image>;
+ status = "okay";
+};
+
+&hdmi_in {
+ hdmi_in_vp0: endpoint {
+ remote-endpoint = <&vp0_out_hdmi>;
+ };
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&hdmi_sound {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ vdd_cpu: regulator@1c {
+ compatible = "tcs,tcs4525";
+ reg = <0x1c>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_cpu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-ramp-delay = <2300>;
+ vin-supply = <&vcc5v0_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ rk809: pmic@20 {
+ compatible = "rockchip,rk809";
+ reg = <0x20>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+ assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
+ assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
+ #clock-cells = <1>;
+ clock-names = "mclk";
+ clocks = <&cru I2S1_MCLKOUT_TX>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int>;
+ rockchip,system-power-controller;
+ #sound-dai-cells = <0>;
+ vcc1-supply = <&vcc3v3_sys>;
+ vcc2-supply = <&vcc3v3_sys>;
+ vcc3-supply = <&vcc3v3_sys>;
+ vcc4-supply = <&vcc3v3_sys>;
+ vcc5-supply = <&vcc3v3_sys>;
+ vcc6-supply = <&vcc3v3_sys>;
+ vcc7-supply = <&vcc3v3_sys>;
+ vcc8-supply = <&vcc3v3_sys>;
+ vcc9-supply = <&vcc3v3_sys>;
+ wakeup-source;
+
+ regulators {
+ vdd_logic: DCDC_REG1 {
+ regulator-name = "vdd_logic";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-init-microvolt = <900000>;
+ regulator-ramp-delay = <6001>;
+ regulator-initial-mode = <0x2>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_gpu: DCDC_REG2 {
+ regulator-name = "vdd_gpu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-init-microvolt = <900000>;
+ regulator-ramp-delay = <6001>;
+ regulator-initial-mode = <0x2>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vdd_npu: DCDC_REG4 {
+ regulator-name = "vdd_npu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-init-microvolt = <900000>;
+ regulator-ramp-delay = <6001>;
+ regulator-initial-mode = <0x2>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v8: DCDC_REG5 {
+ regulator-name = "vcc_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_image: LDO_REG1 {
+ regulator-name = "vdda0v9_image";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda_0v9: LDO_REG2 {
+ regulator-name = "vdda_0v9";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_pmu: LDO_REG3 {
+ regulator-name = "vdda0v9_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vccio_acodec: LDO_REG4 {
+ regulator-name = "vccio_acodec";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd: LDO_REG5 {
+ regulator-name = "vccio_sd";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_pmu: LDO_REG6 {
+ regulator-name = "vcc3v3_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcca_1v8: LDO_REG7 {
+ regulator-name = "vcca_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcca1v8_pmu: LDO_REG8 {
+ regulator-name = "vcca1v8_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcca1v8_image: LDO_REG9 {
+ regulator-name = "vcca1v8_image";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_3v3: SWITCH_REG1 {
+ regulator-name = "vcc_3v3";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_sd: SWITCH_REG2 {
+ regulator-name = "vcc3v3_sd";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&i2s1_8ch {
+ rockchip,trcm-sync-tx-only;
+ status = "okay";
+};
+
+&gmac0 {
+ phy-mode = "rgmii";
+ clock_in_out = "output";
+
+ snps,reset-gpio = <&gpio2 RK_PD3 GPIO_ACTIVE_LOW>;
+ snps,reset-active-low;
+ /* Reset time is 20ms, 100ms for rtl8211f */
+ snps,reset-delays-us = <0 20000 100000>;
+
+ assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>;
+ assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>, <&cru CLK_MAC0_2TOP>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac0_miim
+ &gmac0_tx_bus2
+ &gmac0_rx_bus2
+ &gmac0_rgmii_clk
+ &gmac0_rgmii_bus>;
+
+ tx_delay = <0x22>;
+ rx_delay = <0x0e>;
+
+ phy-handle = <&rgmii_phy0>;
+ status = "okay";
+};
+
+&mdio0 {
+ rgmii_phy0: phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0x0>;
+ };
+};
+
+&gmac1 {
+ phy-mode = "rgmii";
+ clock_in_out = "output";
+
+ snps,reset-gpio = <&gpio3 RK_PA2 GPIO_ACTIVE_LOW>;
+ snps,reset-active-low;
+ /* Reset time is 20ms, 100ms for rtl8211f */
+ snps,reset-delays-us = <0 20000 100000>;
+
+ assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
+ assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru CLK_MAC1_2TOP>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac1m1_miim
+ &gmac1m1_tx_bus2
+ &gmac1m1_rx_bus2
+ &gmac1m1_rgmii_clk
+ &gmac1m1_rgmii_bus>;
+
+ tx_delay = <0x21>;
+ rx_delay = <0x0e>;
+
+ phy-handle = <&rgmii_phy1>;
+ status = "okay";
+};
+
+&mdio1 {
+ rgmii_phy1: phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0x0>;
+ };
+};
+
+&gic {
+ mbi-ranges = <94 31>, <229 31>, <289 31>;
+};
+
+&pcie30phy {
+ status = "okay";
+};
+
+&pcie3x2 {
+ reset-gpios = <&gpio2 RK_PD6 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc3v3_m2_pcie>;
+ status = "okay";
+};
+
+&pcie2x1 {
+ reset-gpios = <&gpio3 RK_PC1 GPIO_ACTIVE_HIGH>;
+ disable-gpios = <&gpio3 RK_PC2 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc3v3_mini_pcie>;
+ status = "okay";
+};
+
+&pmu_io_domains {
+ pmuio2-supply = <&vcc3v3_pmu>;
+ vccio1-supply = <&vccio_acodec>;
+ vccio3-supply = <&vccio_sd>;
+ vccio4-supply = <&vcc_1v8>;
+ vccio5-supply = <&vcc_3v3>;
+ vccio6-supply = <&vcc_1v8>;
+ vccio7-supply = <&vcc_3v3>;
+ status = "okay";
+};
+
+&pwm8 {
+ status = "okay";
+};
+
+&pwm9 {
+ status = "disabled";
+};
+
+&pwm10 {
+ status = "disabled";
+};
+
+&pwm14 {
+ status = "disabled";
+};
+
+&spi3 {
+ pinctrl-0 = <&spi3m1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3m1_xfer>;
+ status = "disabled";
+};
+
+&saradc {
+ vref-supply = <&vcca_1v8>;
+ status = "okay";
+};
+
+&tsadc {
+ rockchip,hw-tshut-mode = <1>;
+ rockchip,hw-tshut-polarity = <0>;
+ status = "okay";
+};
+
+&sdhci {
+ assigned-clocks = <&cru BCLK_EMMC>, <&cru TCLK_EMMC>, <&cru CCLK_EMMC>;
+ assigned-clock-rates = <200000000>, <24000000>, <200000000>;
+ bus-width = <8>;
+ max-frequency = <200000000>;
+ mmc-hs200-1_8v;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd>;
+ supports-emmc;
+ status = "okay";
+};
+
+&sdmmc0 {
+ max-frequency = <150000000>;
+ no-sdio;
+ no-mmc;
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ disable-wp;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc3v3_sd>;
+ vqmmc-supply = <&vccio_sd>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+ status = "okay";
+};
+
+/* USB OTG/USB Host_1 USB 2.0 Comb */
+&usb2phy0 {
+ status = "okay";
+};
+
+&usb2phy0_host {
+ phy-supply = <&vcc5v0_usb30_host>;
+ status = "okay";
+};
+
+&usb2phy0_otg {
+ phy-supply = <&vcc5v0_otg_vbus>;
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+/* USB Host_2/USB Host_3 USB 2.0 Comb */
+&usb2phy1 {
+ status = "okay";
+};
+
+&usb2phy1_host {
+ status = "okay";
+};
+
+&usb2phy1_otg {
+ phy-supply = <&vcc5v0_usb20_host>;
+ status = "okay";
+};
+
+&usb_host1_ehci {
+ status = "okay";
+};
+
+&usb_host1_ohci {
+ status = "okay";
+};
+
+/* MULTI_PHY0 For SATA0, USB3.0 OTG Only USB2.0 */
+&usb_host0_xhci {
+ phys = <&usb2phy0_otg>;
+ phy-names = "usb2-phy";
+ extcon = <&usb2phy0>;
+ maximum-speed = "high-speed";
+ dr_mode = "host";
+ status = "okay";
+};
+
+&sata0 {
+ status = "okay";
+};
+
+/* USB3.0 Host */
+&usb_host1_xhci {
+ status = "okay";
+};
+
+&vop {
+ assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+ assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+ status = "okay";
+};
+
+&vop_mmu {
+ status = "okay";
+};
+
+&vp0 {
+ vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+ reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+ remote-endpoint = <&hdmi_in_vp0>;
+ };
+};
+
+&pinctrl {
+ leds {
+ user_led_pin: user-status-led-pin {
+ rockchip,pins = <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb {
+ vcc5v0_usb20_host_en: vcc5v0-usb20-host-en {
+ rockchip,pins = <0 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ vcc5v0_usb30_host_en: vcc5v0-usb30-host-en {
+ rockchip,pins = <0 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ vcc5v0_otg_vbus_en: vcc5v0-otg-vbus-en {
+ rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pcie {
+ vcc3v3_m2_pcie_en: vcc3v3-m2-pcie-en {
+ rockchip,pins = <0 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ vcc3v3_mini_pcie_en: vcc3v3-mini-pcie-en {
+ rockchip,pins = <3 RK_PC3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int: pmic-int {
+ rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+};
new file mode 100644
@@ -0,0 +1,96 @@
+CONFIG_ARM=y
+CONFIG_SKIP_LOWLEVEL_INIT=y
+CONFIG_COUNTER_FREQUENCY=24000000
+CONFIG_ARCH_ROCKCHIP=y
+CONFIG_TEXT_BASE=0x00a00000
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000
+CONFIG_SF_DEFAULT_SPEED=24000000
+CONFIG_SF_DEFAULT_MODE=0x2000
+CONFIG_DEFAULT_DEVICE_TREE="rk3568-lubancat-2"
+CONFIG_ROCKCHIP_RK3568=y
+CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y
+CONFIG_ROCKCHIP_SPI_IMAGE=y
+CONFIG_SPL_SERIAL=y
+CONFIG_SPL_STACK_R_ADDR=0x600000
+CONFIG_SPL_STACK=0x400000
+CONFIG_DEBUG_UART_BASE=0xFE660000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_SPL_SPI_FLASH_SUPPORT=y
+CONFIG_SPL_SPI=y
+CONFIG_SYS_LOAD_ADDR=0xc00800
+CONFIG_DEBUG_UART=y
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_SPL_FIT_FULL_CHECK=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-lubancat-2.dtb"
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_SPL_MAX_SIZE=0x40000
+CONFIG_SPL_PAD_TO=0x7f8000
+CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
+CONFIG_SPL_BSS_START_ADDR=0x4000000
+CONFIG_SPL_BSS_MAX_SIZE=0x4000
+# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
+# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_CRYPTO=y
+CONFIG_SPL_SPI_LOAD=y
+CONFIG_SYS_SPI_U_BOOT_OFFS=0x60000
+CONFIG_SPL_ATF=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+# CONFIG_SPL_DOS_PARTITION is not set
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_LIVE=y
+CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
+CONFIG_SPL_REGMAP=y
+CONFIG_SPL_SYSCON=y
+CONFIG_SPL_CLK=y
+CONFIG_ROCKCHIP_GPIO=y
+CONFIG_SYS_I2C_ROCKCHIP=y
+CONFIG_MISC=y
+CONFIG_SUPPORT_EMMC_RPMB=y
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_ROCKCHIP=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_SDMA=y
+CONFIG_MMC_SDHCI_ROCKCHIP=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_XTX=y
+CONFIG_ETH_DESIGNWARE=y
+CONFIG_GMAC_ROCKCHIP=y
+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
+CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_RK8XX=y
+CONFIG_REGULATOR_RK8XX=y
+CONFIG_PWM_ROCKCHIP=y
+CONFIG_SPL_RAM=y
+CONFIG_BAUDRATE=1500000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_NS16550_MEM32=y
+CONFIG_ROCKCHIP_SFC=y
+CONFIG_SYSRESET=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_GENERIC=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_GENERIC=y
+CONFIG_USB_DWC3=y
+CONFIG_RSA=y
+CONFIG_SPL_RSA=y
+CONFIG_ERRNO_STR=y
LubanCat 2 is a rk3568 based SBC from EmbedFire. Specification: - Rockchip rk3568 - LPDDR4/4X 1/2/4/8 GB - TF scard slot - eMMC 8/32/64/128 GB - Gigabit ethernet x 2 - HDMI out - USB 2.0 Host x 1 - USB 2.0 Type-C OTG x 1 - USB 3.0 Host x 1 - Mini PCIE interface for WIFI/BT module - M.2 key for 2280 NVME - 40 pin header The dts file is sync from linux mainline. Signed-off-by: Andy Yan <andyshrk@163.com> --- arch/arm/dts/Makefile | 3 +- arch/arm/dts/rk3568-lubancat-2-u-boot.dtsi | 87 +++ arch/arm/dts/rk3568-lubancat-2.dts | 734 +++++++++++++++++++++ configs/lubancat-2-rk3568_defconfig | 96 +++ 4 files changed, 919 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/rk3568-lubancat-2-u-boot.dtsi create mode 100644 arch/arm/dts/rk3568-lubancat-2.dts create mode 100644 configs/lubancat-2-rk3568_defconfig