| Message ID | 20220106030857.1410516-2-judge.packham@gmail.com |
|---|---|
| State | Superseded |
| Delegated to: | Stefan Roese |
| Headers | show |
| Series | [1/2] ARM: mvebu: x530: set MPP55 to gpio | expand |
On 1/6/22 04:08, Chris Packham wrote: > Some older x530 boards have layout issues that cause problems for DDR. > These are usually seen as training failures but can also cause problems > after training has completed. Add an option to enable ECC leaving the > default as N which will work with both old and new boards. > > Signed-off-by: Chris Packham <judge.packham@gmail.com> Just checking: Most likely you don't have the possibility to detect the board version at runtime? If this is not possible: Reviewed-by: Stefan Roese <sr@denx.de> Thanks, Stefan > --- > > arch/arm/mach-mvebu/Kconfig | 1 + > board/alliedtelesis/x530/Kconfig | 20 ++++++++++++++++++++ > board/alliedtelesis/x530/x530.c | 8 +++++++- > 3 files changed, 28 insertions(+), 1 deletion(-) > create mode 100644 board/alliedtelesis/x530/Kconfig > > diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig > index d23cc0c760f1..7388ade98d52 100644 > --- a/arch/arm/mach-mvebu/Kconfig > +++ b/arch/arm/mach-mvebu/Kconfig > @@ -341,5 +341,6 @@ config SECURED_MODE_CSK_INDEX > > source "board/solidrun/clearfog/Kconfig" > source "board/kobol/helios4/Kconfig" > +source "board/alliedtelesis/x530/Kconfig" > > endif > diff --git a/board/alliedtelesis/x530/Kconfig b/board/alliedtelesis/x530/Kconfig > new file mode 100644 > index 000000000000..5c1ae36aebaa > --- /dev/null > +++ b/board/alliedtelesis/x530/Kconfig > @@ -0,0 +1,20 @@ > +menu "x530 configuration" > + depends on TARGET_X530 > + > +config X530_ECC > + bool "Enable DDR3 ECC" > + help > + Some of the older x530 board have layout issues which cause problems > + for the DDR which usually exhibit as DDR training failures or > + problems accessing DDR after training. > + > + The known affected boards are: > + > + * 844-001897-00 (x530-28GTXm, x530-28GPXm, GS980MX/28PSm) > + * 844-001948-00 (GS980MX/28) > + * 844-002008-00 (x530L-52GTX, x530L-52GPX) > + * 844-001974-00 (x530-52GTXm, x530-52GPXm, GS980MX/52PSm) > + > + If you have a newer board you can set Y here, otherwise say N. > + > +endmenu > diff --git a/board/alliedtelesis/x530/x530.c b/board/alliedtelesis/x530/x530.c > index 866b6e68cc16..de20684f4353 100644 > --- a/board/alliedtelesis/x530/x530.c > +++ b/board/alliedtelesis/x530/x530.c > @@ -45,6 +45,12 @@ int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count) > return 0; > } > > +#if CONFIG_IS_ENABLED(X530_ECC) > + #define BUS_MASK BUS_MASK_32BIT_ECC > +#else > + #define BUS_MASK BUS_MASK_32BIT > +#endif > + > /* > * Define the DDR layout / topology here in the board file. This will > * be used by the DDR3 init code in the SPL U-Boot version to configure > @@ -66,7 +72,7 @@ static struct mv_ddr_topology_map board_topology_map = { > 0, 0, /* cas_l cas_wl */ > MV_DDR_TEMP_LOW, /* temperature */ > MV_DDR_TIM_2T} }, /* timing */ > - BUS_MASK_32BIT_ECC, /* subphys mask */ > + BUS_MASK, /* subphys mask */ > MV_DDR_CFG_DEFAULT, /* ddr configuration data source */ > NOT_COMBINED, /* ddr twin-die combined */ > { {0} }, /* raw spd data */ > Viele Grüße, Stefan Roese
On Mon, 10 Jan 2022, 8:37 PM Stefan Roese, <sr@denx.de> wrote: > On 1/6/22 04:08, Chris Packham wrote: > > Some older x530 boards have layout issues that cause problems for DDR. > > These are usually seen as training failures but can also cause problems > > after training has completed. Add an option to enable ECC leaving the > > default as N which will work with both old and new boards. > > > > Signed-off-by: Chris Packham <judge.packham@gmail.com> > > Just checking: Most likely you don't have the possibility to detect the > board version at runtime? > Not in a way that can be done without working RAM. For our internal fork we maintain 2 defconfigs one with ECC one without. We can manage via the BOM which boards get which bootloader. > If this is not possible: > > Reviewed-by: Stefan Roese <sr@denx.de> > > Thanks, > Stefan > > > --- > > > > arch/arm/mach-mvebu/Kconfig | 1 + > > board/alliedtelesis/x530/Kconfig | 20 ++++++++++++++++++++ > > board/alliedtelesis/x530/x530.c | 8 +++++++- > > 3 files changed, 28 insertions(+), 1 deletion(-) > > create mode 100644 board/alliedtelesis/x530/Kconfig > > > > diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig > > index d23cc0c760f1..7388ade98d52 100644 > > --- a/arch/arm/mach-mvebu/Kconfig > > +++ b/arch/arm/mach-mvebu/Kconfig > > @@ -341,5 +341,6 @@ config SECURED_MODE_CSK_INDEX > > > > source "board/solidrun/clearfog/Kconfig" > > source "board/kobol/helios4/Kconfig" > > +source "board/alliedtelesis/x530/Kconfig" > > > > endif > > diff --git a/board/alliedtelesis/x530/Kconfig > b/board/alliedtelesis/x530/Kconfig > > new file mode 100644 > > index 000000000000..5c1ae36aebaa > > --- /dev/null > > +++ b/board/alliedtelesis/x530/Kconfig > > @@ -0,0 +1,20 @@ > > +menu "x530 configuration" > > + depends on TARGET_X530 > > + > > +config X530_ECC > > + bool "Enable DDR3 ECC" > > + help > > + Some of the older x530 board have layout issues which cause > problems > > + for the DDR which usually exhibit as DDR training failures or > > + problems accessing DDR after training. > > + > > + The known affected boards are: > > + > > + * 844-001897-00 (x530-28GTXm, x530-28GPXm, GS980MX/28PSm) > > + * 844-001948-00 (GS980MX/28) > > + * 844-002008-00 (x530L-52GTX, x530L-52GPX) > > + * 844-001974-00 (x530-52GTXm, x530-52GPXm, GS980MX/52PSm) > > + > > + If you have a newer board you can set Y here, otherwise say N. > > + > > +endmenu > > diff --git a/board/alliedtelesis/x530/x530.c > b/board/alliedtelesis/x530/x530.c > > index 866b6e68cc16..de20684f4353 100644 > > --- a/board/alliedtelesis/x530/x530.c > > +++ b/board/alliedtelesis/x530/x530.c > > @@ -45,6 +45,12 @@ int hws_board_topology_load(struct serdes_map > **serdes_map_array, u8 *count) > > return 0; > > } > > > > +#if CONFIG_IS_ENABLED(X530_ECC) > > + #define BUS_MASK BUS_MASK_32BIT_ECC > > +#else > > + #define BUS_MASK BUS_MASK_32BIT > > +#endif > > + > > /* > > * Define the DDR layout / topology here in the board file. This will > > * be used by the DDR3 init code in the SPL U-Boot version to configure > > @@ -66,7 +72,7 @@ static struct mv_ddr_topology_map board_topology_map = > { > > 0, 0, /* cas_l cas_wl */ > > MV_DDR_TEMP_LOW, /* temperature */ > > MV_DDR_TIM_2T} }, /* timing */ > > - BUS_MASK_32BIT_ECC, /* subphys mask */ > > + BUS_MASK, /* subphys mask */ > > MV_DDR_CFG_DEFAULT, /* ddr configuration data source */ > > NOT_COMBINED, /* ddr twin-die combined */ > > { {0} }, /* raw spd data */ > > > > Viele Grüße, > Stefan Roese > > -- > DENX Software Engineering GmbH, Managing Director: Wolfgang Denk > HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany > Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr@denx.de >
On Mon, Jan 10, 2022 at 9:10 PM Chris Packham <judge.packham@gmail.com> wrote: > > > > On Mon, 10 Jan 2022, 8:37 PM Stefan Roese, <sr@denx.de> wrote: >> >> On 1/6/22 04:08, Chris Packham wrote: >> > Some older x530 boards have layout issues that cause problems for DDR. >> > These are usually seen as training failures but can also cause problems >> > after training has completed. Add an option to enable ECC leaving the >> > default as N which will work with both old and new boards. >> > >> > Signed-off-by: Chris Packham <judge.packham@gmail.com> >> >> Just checking: Most likely you don't have the possibility to detect the >> board version at runtime? > > > Not in a way that can be done without working RAM. For our internal fork we maintain 2 defconfigs one with ECC one without. We can manage via the BOM which boards get which bootloader. > >> >> If this is not possible: >> >> Reviewed-by: Stefan Roese <sr@denx.de> >> >> Thanks, >> Stefan >> >> > --- >> > >> > arch/arm/mach-mvebu/Kconfig | 1 + >> > board/alliedtelesis/x530/Kconfig | 20 ++++++++++++++++++++ >> > board/alliedtelesis/x530/x530.c | 8 +++++++- >> > 3 files changed, 28 insertions(+), 1 deletion(-) >> > create mode 100644 board/alliedtelesis/x530/Kconfig >> > >> > diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig >> > index d23cc0c760f1..7388ade98d52 100644 >> > --- a/arch/arm/mach-mvebu/Kconfig >> > +++ b/arch/arm/mach-mvebu/Kconfig >> > @@ -341,5 +341,6 @@ config SECURED_MODE_CSK_INDEX >> > >> > source "board/solidrun/clearfog/Kconfig" >> > source "board/kobol/helios4/Kconfig" >> > +source "board/alliedtelesis/x530/Kconfig" >> > >> > endif >> > diff --git a/board/alliedtelesis/x530/Kconfig b/board/alliedtelesis/x530/Kconfig >> > new file mode 100644 >> > index 000000000000..5c1ae36aebaa >> > --- /dev/null >> > +++ b/board/alliedtelesis/x530/Kconfig >> > @@ -0,0 +1,20 @@ >> > +menu "x530 configuration" >> > + depends on TARGET_X530 >> > + >> > +config X530_ECC >> > + bool "Enable DDR3 ECC" >> > + help >> > + Some of the older x530 board have layout issues which cause problems >> > + for the DDR which usually exhibit as DDR training failures or >> > + problems accessing DDR after training. >> > + >> > + The known affected boards are: >> > + >> > + * 844-001897-00 (x530-28GTXm, x530-28GPXm, GS980MX/28PSm) >> > + * 844-001948-00 (GS980MX/28) >> > + * 844-002008-00 (x530L-52GTX, x530L-52GPX) >> > + * 844-001974-00 (x530-52GTXm, x530-52GPXm, GS980MX/52PSm) >> > + >> > + If you have a newer board you can set Y here, otherwise say N. >> > + >> > +endmenu >> > diff --git a/board/alliedtelesis/x530/x530.c b/board/alliedtelesis/x530/x530.c >> > index 866b6e68cc16..de20684f4353 100644 >> > --- a/board/alliedtelesis/x530/x530.c >> > +++ b/board/alliedtelesis/x530/x530.c >> > @@ -45,6 +45,12 @@ int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count) >> > return 0; >> > } >> > >> > +#if CONFIG_IS_ENABLED(X530_ECC) >> > + #define BUS_MASK BUS_MASK_32BIT_ECC >> > +#else >> > + #define BUS_MASK BUS_MASK_32BIT >> > +#endif >> > + Hmm this doesn't actually appear to be working as intended. When the SPL is built I end up with CONFIG_IS_ENABLED(X530_ECC) == 0 even when I set it to y. Do I need to define a SPL version of this Kconfig symbol? >> > /* >> > * Define the DDR layout / topology here in the board file. This will >> > * be used by the DDR3 init code in the SPL U-Boot version to configure >> > @@ -66,7 +72,7 @@ static struct mv_ddr_topology_map board_topology_map = { >> > 0, 0, /* cas_l cas_wl */ >> > MV_DDR_TEMP_LOW, /* temperature */ >> > MV_DDR_TIM_2T} }, /* timing */ >> > - BUS_MASK_32BIT_ECC, /* subphys mask */ >> > + BUS_MASK, /* subphys mask */ >> > MV_DDR_CFG_DEFAULT, /* ddr configuration data source */ >> > NOT_COMBINED, /* ddr twin-die combined */ >> > { {0} }, /* raw spd data */ >> > >> >> Viele Grüße, >> Stefan Roese >> >> -- >> DENX Software Engineering GmbH, Managing Director: Wolfgang Denk >> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany >> Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr@denx.de
On Tue, Jan 11, 2022 at 02:37:53PM +1300, Chris Packham wrote: > On Mon, Jan 10, 2022 at 9:10 PM Chris Packham <judge.packham@gmail.com> wrote: > > > > > > > > On Mon, 10 Jan 2022, 8:37 PM Stefan Roese, <sr@denx.de> wrote: > >> > >> On 1/6/22 04:08, Chris Packham wrote: > >> > Some older x530 boards have layout issues that cause problems for DDR. > >> > These are usually seen as training failures but can also cause problems > >> > after training has completed. Add an option to enable ECC leaving the > >> > default as N which will work with both old and new boards. > >> > > >> > Signed-off-by: Chris Packham <judge.packham@gmail.com> > >> > >> Just checking: Most likely you don't have the possibility to detect the > >> board version at runtime? > > > > > > Not in a way that can be done without working RAM. For our internal fork we maintain 2 defconfigs one with ECC one without. We can manage via the BOM which boards get which bootloader. > > > >> > >> If this is not possible: > >> > >> Reviewed-by: Stefan Roese <sr@denx.de> > >> > >> Thanks, > >> Stefan > >> > >> > --- > >> > > >> > arch/arm/mach-mvebu/Kconfig | 1 + > >> > board/alliedtelesis/x530/Kconfig | 20 ++++++++++++++++++++ > >> > board/alliedtelesis/x530/x530.c | 8 +++++++- > >> > 3 files changed, 28 insertions(+), 1 deletion(-) > >> > create mode 100644 board/alliedtelesis/x530/Kconfig > >> > > >> > diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig > >> > index d23cc0c760f1..7388ade98d52 100644 > >> > --- a/arch/arm/mach-mvebu/Kconfig > >> > +++ b/arch/arm/mach-mvebu/Kconfig > >> > @@ -341,5 +341,6 @@ config SECURED_MODE_CSK_INDEX > >> > > >> > source "board/solidrun/clearfog/Kconfig" > >> > source "board/kobol/helios4/Kconfig" > >> > +source "board/alliedtelesis/x530/Kconfig" > >> > > >> > endif > >> > diff --git a/board/alliedtelesis/x530/Kconfig b/board/alliedtelesis/x530/Kconfig > >> > new file mode 100644 > >> > index 000000000000..5c1ae36aebaa > >> > --- /dev/null > >> > +++ b/board/alliedtelesis/x530/Kconfig > >> > @@ -0,0 +1,20 @@ > >> > +menu "x530 configuration" > >> > + depends on TARGET_X530 > >> > + > >> > +config X530_ECC > >> > + bool "Enable DDR3 ECC" > >> > + help > >> > + Some of the older x530 board have layout issues which cause problems > >> > + for the DDR which usually exhibit as DDR training failures or > >> > + problems accessing DDR after training. > >> > + > >> > + The known affected boards are: > >> > + > >> > + * 844-001897-00 (x530-28GTXm, x530-28GPXm, GS980MX/28PSm) > >> > + * 844-001948-00 (GS980MX/28) > >> > + * 844-002008-00 (x530L-52GTX, x530L-52GPX) > >> > + * 844-001974-00 (x530-52GTXm, x530-52GPXm, GS980MX/52PSm) > >> > + > >> > + If you have a newer board you can set Y here, otherwise say N. > >> > + > >> > +endmenu > >> > diff --git a/board/alliedtelesis/x530/x530.c b/board/alliedtelesis/x530/x530.c > >> > index 866b6e68cc16..de20684f4353 100644 > >> > --- a/board/alliedtelesis/x530/x530.c > >> > +++ b/board/alliedtelesis/x530/x530.c > >> > @@ -45,6 +45,12 @@ int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count) > >> > return 0; > >> > } > >> > > >> > +#if CONFIG_IS_ENABLED(X530_ECC) > >> > + #define BUS_MASK BUS_MASK_32BIT_ECC > >> > +#else > >> > + #define BUS_MASK BUS_MASK_32BIT > >> > +#endif > >> > + > > Hmm this doesn't actually appear to be working as intended. When the > SPL is built I end up with CONFIG_IS_ENABLED(X530_ECC) == 0 even when > I set it to y. Do I need to define a SPL version of this Kconfig > symbol? If you're using CONFIG_IS_ENABLED, then yes. It doesn't always make sense to use CONFIG_IS_ENABLED or other macros rather than just #ifdef checks.
On 1/11/22 02:37, Chris Packham wrote: > On Mon, Jan 10, 2022 at 9:10 PM Chris Packham <judge.packham@gmail.com> wrote: >> >> >> >> On Mon, 10 Jan 2022, 8:37 PM Stefan Roese, <sr@denx.de> wrote: >>> >>> On 1/6/22 04:08, Chris Packham wrote: >>>> Some older x530 boards have layout issues that cause problems for DDR. >>>> These are usually seen as training failures but can also cause problems >>>> after training has completed. Add an option to enable ECC leaving the >>>> default as N which will work with both old and new boards. >>>> >>>> Signed-off-by: Chris Packham <judge.packham@gmail.com> >>> >>> Just checking: Most likely you don't have the possibility to detect the >>> board version at runtime? >> >> >> Not in a way that can be done without working RAM. For our internal fork we maintain 2 defconfigs one with ECC one without. We can manage via the BOM which boards get which bootloader. >> >>> >>> If this is not possible: >>> >>> Reviewed-by: Stefan Roese <sr@denx.de> >>> >>> Thanks, >>> Stefan >>> >>>> --- >>>> >>>> arch/arm/mach-mvebu/Kconfig | 1 + >>>> board/alliedtelesis/x530/Kconfig | 20 ++++++++++++++++++++ >>>> board/alliedtelesis/x530/x530.c | 8 +++++++- >>>> 3 files changed, 28 insertions(+), 1 deletion(-) >>>> create mode 100644 board/alliedtelesis/x530/Kconfig >>>> >>>> diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig >>>> index d23cc0c760f1..7388ade98d52 100644 >>>> --- a/arch/arm/mach-mvebu/Kconfig >>>> +++ b/arch/arm/mach-mvebu/Kconfig >>>> @@ -341,5 +341,6 @@ config SECURED_MODE_CSK_INDEX >>>> >>>> source "board/solidrun/clearfog/Kconfig" >>>> source "board/kobol/helios4/Kconfig" >>>> +source "board/alliedtelesis/x530/Kconfig" >>>> >>>> endif >>>> diff --git a/board/alliedtelesis/x530/Kconfig b/board/alliedtelesis/x530/Kconfig >>>> new file mode 100644 >>>> index 000000000000..5c1ae36aebaa >>>> --- /dev/null >>>> +++ b/board/alliedtelesis/x530/Kconfig >>>> @@ -0,0 +1,20 @@ >>>> +menu "x530 configuration" >>>> + depends on TARGET_X530 >>>> + >>>> +config X530_ECC >>>> + bool "Enable DDR3 ECC" >>>> + help >>>> + Some of the older x530 board have layout issues which cause problems >>>> + for the DDR which usually exhibit as DDR training failures or >>>> + problems accessing DDR after training. >>>> + >>>> + The known affected boards are: >>>> + >>>> + * 844-001897-00 (x530-28GTXm, x530-28GPXm, GS980MX/28PSm) >>>> + * 844-001948-00 (GS980MX/28) >>>> + * 844-002008-00 (x530L-52GTX, x530L-52GPX) >>>> + * 844-001974-00 (x530-52GTXm, x530-52GPXm, GS980MX/52PSm) >>>> + >>>> + If you have a newer board you can set Y here, otherwise say N. >>>> + >>>> +endmenu >>>> diff --git a/board/alliedtelesis/x530/x530.c b/board/alliedtelesis/x530/x530.c >>>> index 866b6e68cc16..de20684f4353 100644 >>>> --- a/board/alliedtelesis/x530/x530.c >>>> +++ b/board/alliedtelesis/x530/x530.c >>>> @@ -45,6 +45,12 @@ int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count) >>>> return 0; >>>> } >>>> >>>> +#if CONFIG_IS_ENABLED(X530_ECC) >>>> + #define BUS_MASK BUS_MASK_32BIT_ECC >>>> +#else >>>> + #define BUS_MASK BUS_MASK_32BIT >>>> +#endif >>>> + > > Hmm this doesn't actually appear to be working as intended. When the > SPL is built I end up with CONFIG_IS_ENABLED(X530_ECC) == 0 even when > I set it to y. Do I need to define a SPL version of this Kconfig > symbol? AFAIK, IS_ENABLED(CONFIG_X530_ECC) would be a solution here. There is no need for a new SPL Kconfig option this way. Please give it a try. Thanks, Stefan
diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig index d23cc0c760f1..7388ade98d52 100644 --- a/arch/arm/mach-mvebu/Kconfig +++ b/arch/arm/mach-mvebu/Kconfig @@ -341,5 +341,6 @@ config SECURED_MODE_CSK_INDEX source "board/solidrun/clearfog/Kconfig" source "board/kobol/helios4/Kconfig" +source "board/alliedtelesis/x530/Kconfig" endif diff --git a/board/alliedtelesis/x530/Kconfig b/board/alliedtelesis/x530/Kconfig new file mode 100644 index 000000000000..5c1ae36aebaa --- /dev/null +++ b/board/alliedtelesis/x530/Kconfig @@ -0,0 +1,20 @@ +menu "x530 configuration" + depends on TARGET_X530 + +config X530_ECC + bool "Enable DDR3 ECC" + help + Some of the older x530 board have layout issues which cause problems + for the DDR which usually exhibit as DDR training failures or + problems accessing DDR after training. + + The known affected boards are: + + * 844-001897-00 (x530-28GTXm, x530-28GPXm, GS980MX/28PSm) + * 844-001948-00 (GS980MX/28) + * 844-002008-00 (x530L-52GTX, x530L-52GPX) + * 844-001974-00 (x530-52GTXm, x530-52GPXm, GS980MX/52PSm) + + If you have a newer board you can set Y here, otherwise say N. + +endmenu diff --git a/board/alliedtelesis/x530/x530.c b/board/alliedtelesis/x530/x530.c index 866b6e68cc16..de20684f4353 100644 --- a/board/alliedtelesis/x530/x530.c +++ b/board/alliedtelesis/x530/x530.c @@ -45,6 +45,12 @@ int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count) return 0; } +#if CONFIG_IS_ENABLED(X530_ECC) + #define BUS_MASK BUS_MASK_32BIT_ECC +#else + #define BUS_MASK BUS_MASK_32BIT +#endif + /* * Define the DDR layout / topology here in the board file. This will * be used by the DDR3 init code in the SPL U-Boot version to configure @@ -66,7 +72,7 @@ static struct mv_ddr_topology_map board_topology_map = { 0, 0, /* cas_l cas_wl */ MV_DDR_TEMP_LOW, /* temperature */ MV_DDR_TIM_2T} }, /* timing */ - BUS_MASK_32BIT_ECC, /* subphys mask */ + BUS_MASK, /* subphys mask */ MV_DDR_CFG_DEFAULT, /* ddr configuration data source */ NOT_COMBINED, /* ddr twin-die combined */ { {0} }, /* raw spd data */
Some older x530 boards have layout issues that cause problems for DDR. These are usually seen as training failures but can also cause problems after training has completed. Add an option to enable ECC leaving the default as N which will work with both old and new boards. Signed-off-by: Chris Packham <judge.packham@gmail.com> --- arch/arm/mach-mvebu/Kconfig | 1 + board/alliedtelesis/x530/Kconfig | 20 ++++++++++++++++++++ board/alliedtelesis/x530/x530.c | 8 +++++++- 3 files changed, 28 insertions(+), 1 deletion(-) create mode 100644 board/alliedtelesis/x530/Kconfig