Message ID | 20210630211332.v6.1.I8f4599cf3ce092922c55387eeb6a8cd984845d08@changeid |
---|---|
State | Superseded |
Delegated to: | Kever Yang |
Headers | show |
Series | rockchip_sfc: add support for Rockchip SFC | expand |
On Wed, Jun 30, 2021 at 09:31:31PM +0800, Jon Lin wrote: > From: Chris Morgan <macromorgan@hotmail.com> > > This patch adds support for the Rockchip serial flash controller > found on the PX30 SoC. It should work for versions 3-5 of the SFC > IP, however I am only able to test it on v3. > > This is adapted from the WIP SPI-MEM driver for the SFC on mainline > Linux. Note that the main difference between this and earlier versions > of the driver is that this one does not support DMA. In testing > the performance difference (performing a dual mode read on a 128Mb > chip) is negligible. DMA, if used, must also be disabled in SPL > mode when using A-TF anyway. > > Signed-off-by: Chris Morgan <macromorgan@hotmail.com> > Signed-off-by: Jon Lin <jon.lin@rock-chips.com> > --- > > Changes in v6: > - Fix dma transfer logic > - Fix the error of the way to wait for dma transfer finished status > > Changes in v5: > - Support dma transfer > - Add CONFIG_IS_ENABLED(CLK) limitation > - Support spinand devices > - Support SFC ver4 ver5 > - Using "rockchip, sfc" as compatible id > - Get clock from the index to compatible with those case which's > clock-names is not parsed > > Changes in v4: > - None > > Changes in v3: > - Added "rockchip_sfc_adjust_op_work()" function from proposed Linux > driver to fix potential issue on hardware. Note I never noticed > this issue while testing, so I cannot test if it fixed any specific > issue for me. > - Updated of-compatible string back to "rockchip,sfc" to match what > is currently proposed for upstream driver. The hardware itself > has multiple versions but a register is present in the hardware that > is read by the driver to set version specific functionality. > - Updated px30.dtsi and rk3266-odroid-go2.dts device-trees so that > sfc nodes match what is in upstream. > > Changes in v2: > - Resending due to glitch with patch file truncating final two lines > on patch 1/5 and incorrect patch version number on patch 5/5. > > Changes in v1: > - Reworked code to utilize spi-mem framework, and based it closely > off of work in progress code for mainline Linux. > - Removed DMA, as it didn't offer much performance benefit for > booting (in my test cases), added complexity to the code, and > interfered with A-TF. > - Updated the names of the bindings to match the work in progress > Linux code. > - Moved alias to u-boot specific device-tree for Odroid Go Advance. > Alias is updated with the spi0 node pointing to the SFC to > help the sf command as well as facilitate booting from the SFC. > - Note 2 below no longer applies, as rebasing this off of upstream > code should allow the device to work for NAND, and by utilizing > the spi-mem framework it no longer has to extract the parameters > > drivers/spi/Kconfig | 8 + > drivers/spi/Makefile | 1 + > drivers/spi/rockchip_sfc.c | 643 +++++++++++++++++++++++++++++++++++++ > 3 files changed, 652 insertions(+) > create mode 100644 drivers/spi/rockchip_sfc.c > > diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig > index 1494c91763..bef36f2931 100644 > --- a/drivers/spi/Kconfig > +++ b/drivers/spi/Kconfig > @@ -312,6 +312,14 @@ config RENESAS_RPC_SPI > on Renesas RCar Gen3 SoCs. This uses driver model and requires a > device tree binding to operate. > > +config ROCKCHIP_SFC > + bool "Rockchip SFC Driver" > + help > + Enable the Rockchip SFC Driver for SPI NOR flash. This device is > + a limited purpose SPI controller for driving NOR flash on certain > + Rockchip SoCs. This uses driver model and requires a device tree > + binding to operate. > + > config ROCKCHIP_SPI > bool "Rockchip SPI driver" > help > diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile > index cfe4fae1d4..f02e84b5f1 100644 > --- a/drivers/spi/Makefile > +++ b/drivers/spi/Makefile > @@ -52,6 +52,7 @@ obj-$(CONFIG_PIC32_SPI) += pic32_spi.o > obj-$(CONFIG_PL022_SPI) += pl022_spi.o > obj-$(CONFIG_SPI_QUP) += spi-qup.o > obj-$(CONFIG_RENESAS_RPC_SPI) += renesas_rpc_spi.o > +obj-$(CONFIG_ROCKCHIP_SFC) += rockchip_sfc.o > obj-$(CONFIG_ROCKCHIP_SPI) += rk_spi.o > obj-$(CONFIG_SANDBOX_SPI) += sandbox_spi.o > obj-$(CONFIG_SPI_SIFIVE) += spi-sifive.o > diff --git a/drivers/spi/rockchip_sfc.c b/drivers/spi/rockchip_sfc.c > new file mode 100644 > index 0000000000..2d86f136f2 > --- /dev/null > +++ b/drivers/spi/rockchip_sfc.c > @@ -0,0 +1,643 @@ > +// SPDX-License-Identifier: GPL-2.0-only > +/* > + * Rockchip Serial Flash Controller Driver > + * > + * Copyright (c) 2017-2021, Rockchip Inc. > + * Author: Shawn Lin <shawn.lin@rock-chips.com> > + * Chris Morgan <macromorgan@hotmail.com> > + * Jon Lin <Jon.lin@rock-chips.com> > + */ > + > +#include <asm/io.h> > +#include <bouncebuf.h> > +#include <clk.h> > +#include <dm.h> > +#include <linux/bitops.h> > +#include <linux/delay.h> > +#include <linux/iopoll.h> > +#include <spi.h> > +#include <spi-mem.h> > + > +/* System control */ > +#define SFC_CTRL 0x0 > +#define SFC_CTRL_PHASE_SEL_NEGETIVE BIT(1) > +#define SFC_CTRL_CMD_BITS_SHIFT 8 > +#define SFC_CTRL_ADDR_BITS_SHIFT 10 > +#define SFC_CTRL_DATA_BITS_SHIFT 12 > + > +/* Interrupt mask */ > +#define SFC_IMR 0x4 > +#define SFC_IMR_RX_FULL BIT(0) > +#define SFC_IMR_RX_UFLOW BIT(1) > +#define SFC_IMR_TX_OFLOW BIT(2) > +#define SFC_IMR_TX_EMPTY BIT(3) > +#define SFC_IMR_TRAN_FINISH BIT(4) > +#define SFC_IMR_BUS_ERR BIT(5) > +#define SFC_IMR_NSPI_ERR BIT(6) > +#define SFC_IMR_DMA BIT(7) > + > +/* Interrupt clear */ > +#define SFC_ICLR 0x8 > +#define SFC_ICLR_RX_FULL BIT(0) > +#define SFC_ICLR_RX_UFLOW BIT(1) > +#define SFC_ICLR_TX_OFLOW BIT(2) > +#define SFC_ICLR_TX_EMPTY BIT(3) > +#define SFC_ICLR_TRAN_FINISH BIT(4) > +#define SFC_ICLR_BUS_ERR BIT(5) > +#define SFC_ICLR_NSPI_ERR BIT(6) > +#define SFC_ICLR_DMA BIT(7) > + > +/* FIFO threshold level */ > +#define SFC_FTLR 0xc > +#define SFC_FTLR_TX_SHIFT 0 > +#define SFC_FTLR_TX_MASK 0x1f > +#define SFC_FTLR_RX_SHIFT 8 > +#define SFC_FTLR_RX_MASK 0x1f > + > +/* Reset FSM and FIFO */ > +#define SFC_RCVR 0x10 > +#define SFC_RCVR_RESET BIT(0) > + > +/* Enhanced mode */ > +#define SFC_AX 0x14 > + > +/* Address Bit number */ > +#define SFC_ABIT 0x18 > + > +/* Interrupt status */ > +#define SFC_ISR 0x1c > +#define SFC_ISR_RX_FULL_SHIFT BIT(0) > +#define SFC_ISR_RX_UFLOW_SHIFT BIT(1) > +#define SFC_ISR_TX_OFLOW_SHIFT BIT(2) > +#define SFC_ISR_TX_EMPTY_SHIFT BIT(3) > +#define SFC_ISR_TX_FINISH_SHIFT BIT(4) > +#define SFC_ISR_BUS_ERR_SHIFT BIT(5) > +#define SFC_ISR_NSPI_ERR_SHIFT BIT(6) > +#define SFC_ISR_DMA_SHIFT BIT(7) > + > +/* FIFO status */ > +#define SFC_FSR 0x20 > +#define SFC_FSR_TX_IS_FULL BIT(0) > +#define SFC_FSR_TX_IS_EMPTY BIT(1) > +#define SFC_FSR_RX_IS_EMPTY BIT(2) > +#define SFC_FSR_RX_IS_FULL BIT(3) > +#define SFC_FSR_TXLV_MASK GENMASK(12, 8) > +#define SFC_FSR_TXLV_SHIFT 8 > +#define SFC_FSR_RXLV_MASK GENMASK(20, 16) > +#define SFC_FSR_RXLV_SHIFT 16 > + > +/* FSM status */ > +#define SFC_SR 0x24 > +#define SFC_SR_IS_IDLE 0x0 > +#define SFC_SR_IS_BUSY 0x1 > + > +/* Raw interrupt status */ > +#define SFC_RISR 0x28 > +#define SFC_RISR_RX_FULL BIT(0) > +#define SFC_RISR_RX_UNDERFLOW BIT(1) > +#define SFC_RISR_TX_OVERFLOW BIT(2) > +#define SFC_RISR_TX_EMPTY BIT(3) > +#define SFC_RISR_TRAN_FINISH BIT(4) > +#define SFC_RISR_BUS_ERR BIT(5) > +#define SFC_RISR_NSPI_ERR BIT(6) > +#define SFC_RISR_DMA BIT(7) > + > +/* Version */ > +#define SFC_VER 0x2C > +#define SFC_VER_3 0x3 > +#define SFC_VER_4 0x4 > +#define SFC_VER_5 0x5 > + > +/* Delay line controller resiter */ > +#define SFC_DLL_CTRL0 0x3C > +#define SFC_DLL_CTRL0_SCLK_SMP_DLL BIT(15) > +#define SFC_DLL_CTRL0_DLL_MAX_VER4 0xFFU > +#define SFC_DLL_CTRL0_DLL_MAX_VER5 0x1FFU > + > +/* Master trigger */ > +#define SFC_DMA_TRIGGER 0x80 > + > +/* Src or Dst addr for master */ > +#define SFC_DMA_ADDR 0x84 > + > +/* Length control register extension 32GB */ > +#define SFC_LEN_CTRL 0x88 > +#define SFC_LEN_CTRL_TRB_SEL 1 > +#define SFC_LEN_EXT 0x8C > + > +/* Command */ > +#define SFC_CMD 0x100 > +#define SFC_CMD_IDX_SHIFT 0 > +#define SFC_CMD_DUMMY_SHIFT 8 > +#define SFC_CMD_DIR_SHIFT 12 > +#define SFC_CMD_DIR_RD 0 > +#define SFC_CMD_DIR_WR 1 > +#define SFC_CMD_ADDR_SHIFT 14 > +#define SFC_CMD_ADDR_0BITS 0 > +#define SFC_CMD_ADDR_24BITS 1 > +#define SFC_CMD_ADDR_32BITS 2 > +#define SFC_CMD_ADDR_XBITS 3 > +#define SFC_CMD_TRAN_BYTES_SHIFT 16 > +#define SFC_CMD_CS_SHIFT 30 > + > +/* Address */ > +#define SFC_ADDR 0x104 > + > +/* Data */ > +#define SFC_DATA 0x108 > + > +/* The controller and documentation reports that it supports up to 4 CS > + * devices (0-3), however I have only been able to test a single CS (CS 0) > + * due to the configuration of my device. > + */ > +#define SFC_MAX_CHIPSELECT_NUM 4 > + > +/* The SFC can transfer max 16KB - 1 at one time > + * we set it to 15.5KB here for alignment. > + */ > +#define SFC_MAX_IOSIZE_VER3 (512 * 31) > + > +#define SFC_MAX_IOSIZE_VER4 (0xFFFFFFFFU) > + > +/* DMA is only enabled for large data transmission */ > +#define SFC_DMA_TRANS_THRETHOLD (0x40) > + > +/* Maximum clock values from datasheet suggest keeping clock value under > + * 150MHz. No minimum or average value is suggested, but the U-boot BSP driver > + * has a minimum of 10MHz and a default of 80MHz which seems reasonable. > + */ > +#define SFC_MIN_SPEED_HZ (10 * 1000 * 1000) > +#define SFC_DEFAULT_SPEED_HZ (80 * 1000 * 1000) > +#define SFC_MAX_SPEED_HZ (150 * 1000 * 1000) > + > +struct rockchip_sfc { > + void __iomem *regbase; > + struct clk hclk; > + struct clk clk; > + u32 max_freq; > + u32 speed; > + bool use_dma; > + u32 max_iosize; > + u16 version; > +}; > + > +static int rockchip_sfc_reset(struct rockchip_sfc *sfc) > +{ > + int err; > + u32 status; > + > + writel(SFC_RCVR_RESET, sfc->regbase + SFC_RCVR); > + > + err = readl_poll_timeout(sfc->regbase + SFC_RCVR, status, > + !(status & SFC_RCVR_RESET), > + 1000000); > + if (err) > + printf("SFC reset never finished\n"); > + > + /* Still need to clear the masked interrupt from RISR */ > + writel(0xFFFFFFFF, sfc->regbase + SFC_ICLR); > + > + debug("reset\n"); > + > + return err; > +} > + > +static u16 rockchip_sfc_get_version(struct rockchip_sfc *sfc) > +{ > + return (u16)(readl(sfc->regbase + SFC_VER) & 0xffff); > +} > + > +static u32 rockchip_sfc_get_max_iosize(struct rockchip_sfc *sfc) > +{ > + if (rockchip_sfc_get_version(sfc) >= SFC_VER_4) > + return SFC_MAX_IOSIZE_VER4; > + > + return SFC_MAX_IOSIZE_VER3; > +} > + > +static int rockchip_sfc_init(struct rockchip_sfc *sfc) > +{ > + writel(0, sfc->regbase + SFC_CTRL); > + if (rockchip_sfc_get_version(sfc) >= SFC_VER_4) > + writel(SFC_LEN_CTRL_TRB_SEL, sfc->regbase + SFC_LEN_CTRL); > + > + return 0; > +} > + > +static int rockchip_sfc_ofdata_to_platdata(struct udevice *bus) > +{ > + struct rockchip_sfc *sfc = dev_get_plat(bus); > + > + sfc->regbase = dev_read_addr_ptr(bus); > + > +#if CONFIG_IS_ENABLED(CLK) > + int ret; > + > + ret = clk_get_by_index(bus, 0, &sfc->clk); > + if (ret < 0) { > + printf("Could not get clock for %s: %d\n", bus->name, ret); > + return ret; > + } > + > + ret = clk_get_by_index(bus, 1, &sfc->hclk); > + if (ret < 0) { > + printf("Could not get ahb clock for %s: %d\n", bus->name, ret); > + return ret; > + } > +#endif > + > + return 0; > +} > + > +static int rockchip_sfc_probe(struct udevice *bus) > +{ > + struct rockchip_sfc *sfc = dev_get_plat(bus); > + int ret; > + > +#if CONFIG_IS_ENABLED(CLK) > + ret = clk_enable(&sfc->hclk); > + if (ret) > + debug("Enable ahb clock fail %s: %d\n", bus->name, ret); I'm getting an enable ahb clock fail when I try to use this driver (Odroid Go Advance, same as for Linux). > + > + ret = clk_enable(&sfc->clk); > + if (ret) > + debug("Enable clock fail for %s: %d\n", bus->name, ret); Also get a clock fail error when I try to use this driver. > + > + ret = clk_set_rate(&sfc->clk, SFC_DEFAULT_SPEED_HZ); > + if (ret) > + debug("Could not set sfc clock for %s: %d\n", bus->name, ret); > +#endif > + > + ret = rockchip_sfc_init(sfc); > + if (ret) > + goto err_init; > + > + sfc->use_dma = true; We'll need a way to disable DMA, otherwise this driver cannot be used in SPL mode prior to the load of A-TF (just like the rk_sdmmc driver DMA causes issues with A-TF in SPL mode). > + sfc->max_iosize = rockchip_sfc_get_max_iosize(sfc); > + sfc->version = rockchip_sfc_get_version(sfc); > + sfc->speed = SFC_DEFAULT_SPEED_HZ; > + > + return 0; > + > +err_init: > +#if CONFIG_IS_ENABLED(CLK) > + clk_disable(&sfc->clk); > + clk_disable(&sfc->hclk); > +#endif > + > + return ret; > +} > + > +static inline int rockchip_sfc_get_fifo_level(struct rockchip_sfc *sfc, int wr) > +{ > + u32 fsr = readl(sfc->regbase + SFC_FSR); > + int level; > + > + if (wr) > + level = (fsr & SFC_FSR_TXLV_MASK) >> SFC_FSR_TXLV_SHIFT; > + else > + level = (fsr & SFC_FSR_RXLV_MASK) >> SFC_FSR_RXLV_SHIFT; > + > + return level; > +} > + > +static int rockchip_sfc_wait_fifo_ready(struct rockchip_sfc *sfc, int wr, u32 timeout) > +{ > + unsigned long tbase = get_timer(0); > + int level; > + > + while (!(level = rockchip_sfc_get_fifo_level(sfc, wr))) { > + if (get_timer(tbase) > timeout) { > + debug("%s fifo timeout\n", wr ? "write" : "read"); > + return -ETIMEDOUT; > + } > + udelay(1); > + } > + > + return level; > +} > + > +static void rockchip_sfc_adjust_op_work(struct spi_mem_op *op) > +{ > + if (unlikely(op->dummy.nbytes && !op->addr.nbytes)) { > + /* > + * SFC not support output DUMMY cycles right after CMD cycles, so > + * treat it as ADDR cycles. > + */ > + op->addr.nbytes = op->dummy.nbytes; > + op->addr.buswidth = op->dummy.buswidth; > + op->addr.val = 0xFFFFFFFFF; > + > + op->dummy.nbytes = 0; > + } > +} > + > +static int rockchip_sfc_wait_for_dma_finished(struct rockchip_sfc *sfc, int timeout) > +{ > + unsigned long tbase; > + > + /* Wait for the DMA interrupt status */ > + tbase = get_timer(0); > + while (!(readl(sfc->regbase + SFC_RISR) & SFC_RISR_DMA)) { > + if (get_timer(tbase) > timeout) { > + printf("dma timeout\n"); > + rockchip_sfc_reset(sfc); > + > + return -ETIMEDOUT; > + } > + > + udelay(1); > + } > + > + writel(0xFFFFFFFF, sfc->regbase + SFC_ICLR); > + > + return 0; > +} > + > +static int rockchip_sfc_xfer_setup(struct rockchip_sfc *sfc, > + struct spi_slave *mem, > + const struct spi_mem_op *op, > + u32 len) > +{ > + struct dm_spi_slave_plat *plat = dev_get_parent_plat(mem->dev); > + u32 ctrl = 0, cmd = 0; > + > + /* set CMD */ > + cmd = op->cmd.opcode; > + ctrl |= ((op->cmd.buswidth >> 1) << SFC_CTRL_CMD_BITS_SHIFT); > + > + /* set ADDR */ > + if (op->addr.nbytes) { > + if (op->addr.nbytes == 4) { > + cmd |= SFC_CMD_ADDR_32BITS << SFC_CMD_ADDR_SHIFT; > + } else if (op->addr.nbytes == 3) { > + cmd |= SFC_CMD_ADDR_24BITS << SFC_CMD_ADDR_SHIFT; > + } else { > + cmd |= SFC_CMD_ADDR_XBITS << SFC_CMD_ADDR_SHIFT; > + writel(op->addr.nbytes * 8 - 1, sfc->regbase + SFC_ABIT); > + } > + > + ctrl |= ((op->addr.buswidth >> 1) << SFC_CTRL_ADDR_BITS_SHIFT); > + } > + > + /* set DUMMY */ > + if (op->dummy.nbytes) { > + if (op->dummy.buswidth == 4) > + cmd |= op->dummy.nbytes * 2 << SFC_CMD_DUMMY_SHIFT; > + else if (op->dummy.buswidth == 2) > + cmd |= op->dummy.nbytes * 4 << SFC_CMD_DUMMY_SHIFT; > + else > + cmd |= op->dummy.nbytes * 8 << SFC_CMD_DUMMY_SHIFT; > + } > + > + /* set DATA */ > + if (sfc->version >= SFC_VER_4) /* Clear it if no data to transfer */ > + writel(len, sfc->regbase + SFC_LEN_EXT); > + else > + cmd |= len << SFC_CMD_TRAN_BYTES_SHIFT; > + if (len) { > + if (op->data.dir == SPI_MEM_DATA_OUT) > + cmd |= SFC_CMD_DIR_WR << SFC_CMD_DIR_SHIFT; > + > + ctrl |= ((op->data.buswidth >> 1) << SFC_CTRL_DATA_BITS_SHIFT); > + } > + if (!len && op->addr.nbytes) > + cmd |= SFC_CMD_DIR_WR << SFC_CMD_DIR_SHIFT; > + > + /* set the Controller */ > + ctrl |= SFC_CTRL_PHASE_SEL_NEGETIVE; > + cmd |= plat->cs << SFC_CMD_CS_SHIFT; > + > + debug("addr.nbytes=%x(x%d) dummy.nbytes=%x(x%d)\n", > + op->addr.nbytes, op->addr.buswidth, > + op->dummy.nbytes, op->dummy.buswidth); > + debug("ctrl=%x cmd=%x addr=%llx len=%x\n", > + ctrl, cmd, op->addr.val, len); > + > + writel(ctrl, sfc->regbase + SFC_CTRL); > + writel(cmd, sfc->regbase + SFC_CMD); > + if (op->addr.nbytes) > + writel(op->addr.val, sfc->regbase + SFC_ADDR); > + > + return 0; > +} > + > +static int rockchip_sfc_write_fifo(struct rockchip_sfc *sfc, const u8 *buf, int len) > +{ > + u8 bytes = len & 0x3; > + u32 dwords; > + int tx_level; > + u32 write_words; > + u32 tmp = 0; > + > + dwords = len >> 2; > + while (dwords) { > + tx_level = rockchip_sfc_wait_fifo_ready(sfc, SFC_CMD_DIR_WR, 1000); > + if (tx_level < 0) > + return tx_level; > + write_words = min_t(u32, tx_level, dwords); > + writesl(sfc->regbase + SFC_DATA, buf, write_words); > + buf += write_words << 2; > + dwords -= write_words; > + } > + > + /* write the rest non word aligned bytes */ > + if (bytes) { > + tx_level = rockchip_sfc_wait_fifo_ready(sfc, SFC_CMD_DIR_WR, 1000); > + if (tx_level < 0) > + return tx_level; > + memcpy(&tmp, buf, bytes); > + writel(tmp, sfc->regbase + SFC_DATA); > + } > + > + return len; > +} > + > +static int rockchip_sfc_read_fifo(struct rockchip_sfc *sfc, u8 *buf, int len) > +{ > + u8 bytes = len & 0x3; > + u32 dwords; > + u8 read_words; > + int rx_level; > + int tmp; > + > + /* word aligned access only */ > + dwords = len >> 2; > + while (dwords) { > + rx_level = rockchip_sfc_wait_fifo_ready(sfc, SFC_CMD_DIR_RD, 1000); > + if (rx_level < 0) > + return rx_level; > + read_words = min_t(u32, rx_level, dwords); > + readsl(sfc->regbase + SFC_DATA, buf, read_words); > + buf += read_words << 2; > + dwords -= read_words; > + } > + > + /* read the rest non word aligned bytes */ > + if (bytes) { > + rx_level = rockchip_sfc_wait_fifo_ready(sfc, SFC_CMD_DIR_RD, 1000); > + if (rx_level < 0) > + return rx_level; > + tmp = readl(sfc->regbase + SFC_DATA); > + memcpy(buf, &tmp, bytes); > + } > + > + return len; > +} > + > +static int rockchip_sfc_fifo_transfer_dma(struct rockchip_sfc *sfc, dma_addr_t dma_buf, size_t len) > +{ > + writel(0xFFFFFFFF, sfc->regbase + SFC_ICLR); > + writel((u32)dma_buf, sfc->regbase + SFC_DMA_ADDR); > + writel(0x1, sfc->regbase + SFC_DMA_TRIGGER); > + > + return len; > +} > + > +static int rockchip_sfc_xfer_data_poll(struct rockchip_sfc *sfc, > + const struct spi_mem_op *op, u32 len) > +{ > + debug("xfer_poll len=%x\n", len); > + > + if (op->data.dir == SPI_MEM_DATA_OUT) > + return rockchip_sfc_write_fifo(sfc, op->data.buf.out, len); > + else > + return rockchip_sfc_read_fifo(sfc, op->data.buf.in, len); > +} > + > +static int rockchip_sfc_xfer_data_dma(struct rockchip_sfc *sfc, > + const struct spi_mem_op *op, u32 len) > +{ > + struct bounce_buffer bb; > + unsigned int bb_flags; > + void *dma_buf; > + int ret; > + > + debug("xfer_dma len=%x\n", len); > + > + if (op->data.dir == SPI_MEM_DATA_OUT) { > + dma_buf = (void *)op->data.buf.out; > + bb_flags = GEN_BB_READ; > + } else { > + dma_buf = (void *)op->data.buf.in; > + bb_flags = GEN_BB_WRITE; > + } > + > + ret = bounce_buffer_start(&bb, dma_buf, len, bb_flags); > + if (ret) > + return ret; > + > + ret = rockchip_sfc_fifo_transfer_dma(sfc, (dma_addr_t)bb.bounce_buffer, len); > + rockchip_sfc_wait_for_dma_finished(sfc, len * 10); > + bounce_buffer_stop(&bb); > + > + return ret; > +} > + > +static int rockchip_sfc_xfer_done(struct rockchip_sfc *sfc, u32 timeout_us) > +{ > + unsigned long tbase = get_timer(0); > + int ret = 0; > + u32 timeout = timeout_us; > + > + while (readl(sfc->regbase + SFC_SR) & SFC_SR_IS_BUSY) { > + if (get_timer(tbase) > timeout) { > + printf("wait sfc idle timeout\n"); > + rockchip_sfc_reset(sfc); > + > + return -ETIMEDOUT; > + } > + > + udelay(1); > + } > + > + return ret; > +} > + > +static int rockchip_sfc_exec_op(struct spi_slave *mem, > + const struct spi_mem_op *op) > +{ > + struct rockchip_sfc *sfc = dev_get_plat(mem->dev->parent); > + u32 len = min_t(u32, op->data.nbytes, sfc->max_iosize); > + int ret; > + > +#if CONFIG_IS_ENABLED(CLK) > + if (unlikely(mem->max_hz != sfc->speed)) { > + ret = clk_set_rate(&sfc->clk, clamp(mem->max_hz, (uint)SFC_MIN_SPEED_HZ, > + (uint)SFC_MAX_SPEED_HZ)); > + if (ret < 0) { > + printf("set_freq=%dHz fail, check if it's the cru support level\n", > + mem->max_hz); > + return ret; > + } > + > + sfc->max_freq = mem->max_hz; > + sfc->speed = mem->max_hz; > + debug("set_freq=%dHz real_freq=%dHz\n", sfc->max_freq, sfc->speed); > + } > +#endif > + > + rockchip_sfc_adjust_op_work((struct spi_mem_op *)op); > + > + rockchip_sfc_xfer_setup(sfc, mem, op, len); > + if (len) { > + if (likely(sfc->use_dma) && !(len & 0x3) && len >= SFC_DMA_TRANS_THRETHOLD) > + ret = rockchip_sfc_xfer_data_dma(sfc, op, len); > + else > + ret = rockchip_sfc_xfer_data_poll(sfc, op, len); > + > + if (ret != len) { > + printf("xfer data failed ret %d dir %d\n", ret, op->data.dir); > + > + return -EIO; > + } > + } > + > + return rockchip_sfc_xfer_done(sfc, 100000); > +} > + > +static int rockchip_sfc_adjust_op_size(struct spi_slave *mem, struct spi_mem_op *op) > +{ > + struct rockchip_sfc *sfc = dev_get_plat(mem->dev->parent); > + > + op->data.nbytes = min(op->data.nbytes, sfc->max_iosize); > + return 0; > +} > + > +static int rockchip_sfc_set_speed(struct udevice *bus, uint speed) > +{ > + /* We set up speed later for each transmission. > + */ > + return 0; > +} > + > +static int rockchip_sfc_set_mode(struct udevice *bus, uint mode) > +{ > + return 0; > +} > + > +static const struct spi_controller_mem_ops rockchip_sfc_mem_ops = { > + .adjust_op_size = rockchip_sfc_adjust_op_size, > + .exec_op = rockchip_sfc_exec_op, > +}; > + > +static const struct dm_spi_ops rockchip_sfc_ops = { > + .mem_ops = &rockchip_sfc_mem_ops, > + .set_speed = rockchip_sfc_set_speed, > + .set_mode = rockchip_sfc_set_mode, > +}; > + > +static const struct udevice_id rockchip_sfc_ids[] = { > + { .compatible = "rockchip,sfc"}, > + {}, > +}; > + > +U_BOOT_DRIVER(rockchip_sfc_driver) = { > + .name = "rockchip_sfc", > + .id = UCLASS_SPI, > + .of_match = rockchip_sfc_ids, > + .ops = &rockchip_sfc_ops, > + .of_to_plat = rockchip_sfc_ofdata_to_platdata, > + .plat_auto = sizeof(struct rockchip_sfc), > + .probe = rockchip_sfc_probe, > +}; > -- > 2.17.1 > > >
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index 1494c91763..bef36f2931 100644 --- a/drivers/spi/Kconfig +++ b/drivers/spi/Kconfig @@ -312,6 +312,14 @@ config RENESAS_RPC_SPI on Renesas RCar Gen3 SoCs. This uses driver model and requires a device tree binding to operate. +config ROCKCHIP_SFC + bool "Rockchip SFC Driver" + help + Enable the Rockchip SFC Driver for SPI NOR flash. This device is + a limited purpose SPI controller for driving NOR flash on certain + Rockchip SoCs. This uses driver model and requires a device tree + binding to operate. + config ROCKCHIP_SPI bool "Rockchip SPI driver" help diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index cfe4fae1d4..f02e84b5f1 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -52,6 +52,7 @@ obj-$(CONFIG_PIC32_SPI) += pic32_spi.o obj-$(CONFIG_PL022_SPI) += pl022_spi.o obj-$(CONFIG_SPI_QUP) += spi-qup.o obj-$(CONFIG_RENESAS_RPC_SPI) += renesas_rpc_spi.o +obj-$(CONFIG_ROCKCHIP_SFC) += rockchip_sfc.o obj-$(CONFIG_ROCKCHIP_SPI) += rk_spi.o obj-$(CONFIG_SANDBOX_SPI) += sandbox_spi.o obj-$(CONFIG_SPI_SIFIVE) += spi-sifive.o diff --git a/drivers/spi/rockchip_sfc.c b/drivers/spi/rockchip_sfc.c new file mode 100644 index 0000000000..2d86f136f2 --- /dev/null +++ b/drivers/spi/rockchip_sfc.c @@ -0,0 +1,643 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Rockchip Serial Flash Controller Driver + * + * Copyright (c) 2017-2021, Rockchip Inc. + * Author: Shawn Lin <shawn.lin@rock-chips.com> + * Chris Morgan <macromorgan@hotmail.com> + * Jon Lin <Jon.lin@rock-chips.com> + */ + +#include <asm/io.h> +#include <bouncebuf.h> +#include <clk.h> +#include <dm.h> +#include <linux/bitops.h> +#include <linux/delay.h> +#include <linux/iopoll.h> +#include <spi.h> +#include <spi-mem.h> + +/* System control */ +#define SFC_CTRL 0x0 +#define SFC_CTRL_PHASE_SEL_NEGETIVE BIT(1) +#define SFC_CTRL_CMD_BITS_SHIFT 8 +#define SFC_CTRL_ADDR_BITS_SHIFT 10 +#define SFC_CTRL_DATA_BITS_SHIFT 12 + +/* Interrupt mask */ +#define SFC_IMR 0x4 +#define SFC_IMR_RX_FULL BIT(0) +#define SFC_IMR_RX_UFLOW BIT(1) +#define SFC_IMR_TX_OFLOW BIT(2) +#define SFC_IMR_TX_EMPTY BIT(3) +#define SFC_IMR_TRAN_FINISH BIT(4) +#define SFC_IMR_BUS_ERR BIT(5) +#define SFC_IMR_NSPI_ERR BIT(6) +#define SFC_IMR_DMA BIT(7) + +/* Interrupt clear */ +#define SFC_ICLR 0x8 +#define SFC_ICLR_RX_FULL BIT(0) +#define SFC_ICLR_RX_UFLOW BIT(1) +#define SFC_ICLR_TX_OFLOW BIT(2) +#define SFC_ICLR_TX_EMPTY BIT(3) +#define SFC_ICLR_TRAN_FINISH BIT(4) +#define SFC_ICLR_BUS_ERR BIT(5) +#define SFC_ICLR_NSPI_ERR BIT(6) +#define SFC_ICLR_DMA BIT(7) + +/* FIFO threshold level */ +#define SFC_FTLR 0xc +#define SFC_FTLR_TX_SHIFT 0 +#define SFC_FTLR_TX_MASK 0x1f +#define SFC_FTLR_RX_SHIFT 8 +#define SFC_FTLR_RX_MASK 0x1f + +/* Reset FSM and FIFO */ +#define SFC_RCVR 0x10 +#define SFC_RCVR_RESET BIT(0) + +/* Enhanced mode */ +#define SFC_AX 0x14 + +/* Address Bit number */ +#define SFC_ABIT 0x18 + +/* Interrupt status */ +#define SFC_ISR 0x1c +#define SFC_ISR_RX_FULL_SHIFT BIT(0) +#define SFC_ISR_RX_UFLOW_SHIFT BIT(1) +#define SFC_ISR_TX_OFLOW_SHIFT BIT(2) +#define SFC_ISR_TX_EMPTY_SHIFT BIT(3) +#define SFC_ISR_TX_FINISH_SHIFT BIT(4) +#define SFC_ISR_BUS_ERR_SHIFT BIT(5) +#define SFC_ISR_NSPI_ERR_SHIFT BIT(6) +#define SFC_ISR_DMA_SHIFT BIT(7) + +/* FIFO status */ +#define SFC_FSR 0x20 +#define SFC_FSR_TX_IS_FULL BIT(0) +#define SFC_FSR_TX_IS_EMPTY BIT(1) +#define SFC_FSR_RX_IS_EMPTY BIT(2) +#define SFC_FSR_RX_IS_FULL BIT(3) +#define SFC_FSR_TXLV_MASK GENMASK(12, 8) +#define SFC_FSR_TXLV_SHIFT 8 +#define SFC_FSR_RXLV_MASK GENMASK(20, 16) +#define SFC_FSR_RXLV_SHIFT 16 + +/* FSM status */ +#define SFC_SR 0x24 +#define SFC_SR_IS_IDLE 0x0 +#define SFC_SR_IS_BUSY 0x1 + +/* Raw interrupt status */ +#define SFC_RISR 0x28 +#define SFC_RISR_RX_FULL BIT(0) +#define SFC_RISR_RX_UNDERFLOW BIT(1) +#define SFC_RISR_TX_OVERFLOW BIT(2) +#define SFC_RISR_TX_EMPTY BIT(3) +#define SFC_RISR_TRAN_FINISH BIT(4) +#define SFC_RISR_BUS_ERR BIT(5) +#define SFC_RISR_NSPI_ERR BIT(6) +#define SFC_RISR_DMA BIT(7) + +/* Version */ +#define SFC_VER 0x2C +#define SFC_VER_3 0x3 +#define SFC_VER_4 0x4 +#define SFC_VER_5 0x5 + +/* Delay line controller resiter */ +#define SFC_DLL_CTRL0 0x3C +#define SFC_DLL_CTRL0_SCLK_SMP_DLL BIT(15) +#define SFC_DLL_CTRL0_DLL_MAX_VER4 0xFFU +#define SFC_DLL_CTRL0_DLL_MAX_VER5 0x1FFU + +/* Master trigger */ +#define SFC_DMA_TRIGGER 0x80 + +/* Src or Dst addr for master */ +#define SFC_DMA_ADDR 0x84 + +/* Length control register extension 32GB */ +#define SFC_LEN_CTRL 0x88 +#define SFC_LEN_CTRL_TRB_SEL 1 +#define SFC_LEN_EXT 0x8C + +/* Command */ +#define SFC_CMD 0x100 +#define SFC_CMD_IDX_SHIFT 0 +#define SFC_CMD_DUMMY_SHIFT 8 +#define SFC_CMD_DIR_SHIFT 12 +#define SFC_CMD_DIR_RD 0 +#define SFC_CMD_DIR_WR 1 +#define SFC_CMD_ADDR_SHIFT 14 +#define SFC_CMD_ADDR_0BITS 0 +#define SFC_CMD_ADDR_24BITS 1 +#define SFC_CMD_ADDR_32BITS 2 +#define SFC_CMD_ADDR_XBITS 3 +#define SFC_CMD_TRAN_BYTES_SHIFT 16 +#define SFC_CMD_CS_SHIFT 30 + +/* Address */ +#define SFC_ADDR 0x104 + +/* Data */ +#define SFC_DATA 0x108 + +/* The controller and documentation reports that it supports up to 4 CS + * devices (0-3), however I have only been able to test a single CS (CS 0) + * due to the configuration of my device. + */ +#define SFC_MAX_CHIPSELECT_NUM 4 + +/* The SFC can transfer max 16KB - 1 at one time + * we set it to 15.5KB here for alignment. + */ +#define SFC_MAX_IOSIZE_VER3 (512 * 31) + +#define SFC_MAX_IOSIZE_VER4 (0xFFFFFFFFU) + +/* DMA is only enabled for large data transmission */ +#define SFC_DMA_TRANS_THRETHOLD (0x40) + +/* Maximum clock values from datasheet suggest keeping clock value under + * 150MHz. No minimum or average value is suggested, but the U-boot BSP driver + * has a minimum of 10MHz and a default of 80MHz which seems reasonable. + */ +#define SFC_MIN_SPEED_HZ (10 * 1000 * 1000) +#define SFC_DEFAULT_SPEED_HZ (80 * 1000 * 1000) +#define SFC_MAX_SPEED_HZ (150 * 1000 * 1000) + +struct rockchip_sfc { + void __iomem *regbase; + struct clk hclk; + struct clk clk; + u32 max_freq; + u32 speed; + bool use_dma; + u32 max_iosize; + u16 version; +}; + +static int rockchip_sfc_reset(struct rockchip_sfc *sfc) +{ + int err; + u32 status; + + writel(SFC_RCVR_RESET, sfc->regbase + SFC_RCVR); + + err = readl_poll_timeout(sfc->regbase + SFC_RCVR, status, + !(status & SFC_RCVR_RESET), + 1000000); + if (err) + printf("SFC reset never finished\n"); + + /* Still need to clear the masked interrupt from RISR */ + writel(0xFFFFFFFF, sfc->regbase + SFC_ICLR); + + debug("reset\n"); + + return err; +} + +static u16 rockchip_sfc_get_version(struct rockchip_sfc *sfc) +{ + return (u16)(readl(sfc->regbase + SFC_VER) & 0xffff); +} + +static u32 rockchip_sfc_get_max_iosize(struct rockchip_sfc *sfc) +{ + if (rockchip_sfc_get_version(sfc) >= SFC_VER_4) + return SFC_MAX_IOSIZE_VER4; + + return SFC_MAX_IOSIZE_VER3; +} + +static int rockchip_sfc_init(struct rockchip_sfc *sfc) +{ + writel(0, sfc->regbase + SFC_CTRL); + if (rockchip_sfc_get_version(sfc) >= SFC_VER_4) + writel(SFC_LEN_CTRL_TRB_SEL, sfc->regbase + SFC_LEN_CTRL); + + return 0; +} + +static int rockchip_sfc_ofdata_to_platdata(struct udevice *bus) +{ + struct rockchip_sfc *sfc = dev_get_plat(bus); + + sfc->regbase = dev_read_addr_ptr(bus); + +#if CONFIG_IS_ENABLED(CLK) + int ret; + + ret = clk_get_by_index(bus, 0, &sfc->clk); + if (ret < 0) { + printf("Could not get clock for %s: %d\n", bus->name, ret); + return ret; + } + + ret = clk_get_by_index(bus, 1, &sfc->hclk); + if (ret < 0) { + printf("Could not get ahb clock for %s: %d\n", bus->name, ret); + return ret; + } +#endif + + return 0; +} + +static int rockchip_sfc_probe(struct udevice *bus) +{ + struct rockchip_sfc *sfc = dev_get_plat(bus); + int ret; + +#if CONFIG_IS_ENABLED(CLK) + ret = clk_enable(&sfc->hclk); + if (ret) + debug("Enable ahb clock fail %s: %d\n", bus->name, ret); + + ret = clk_enable(&sfc->clk); + if (ret) + debug("Enable clock fail for %s: %d\n", bus->name, ret); + + ret = clk_set_rate(&sfc->clk, SFC_DEFAULT_SPEED_HZ); + if (ret) + debug("Could not set sfc clock for %s: %d\n", bus->name, ret); +#endif + + ret = rockchip_sfc_init(sfc); + if (ret) + goto err_init; + + sfc->use_dma = true; + sfc->max_iosize = rockchip_sfc_get_max_iosize(sfc); + sfc->version = rockchip_sfc_get_version(sfc); + sfc->speed = SFC_DEFAULT_SPEED_HZ; + + return 0; + +err_init: +#if CONFIG_IS_ENABLED(CLK) + clk_disable(&sfc->clk); + clk_disable(&sfc->hclk); +#endif + + return ret; +} + +static inline int rockchip_sfc_get_fifo_level(struct rockchip_sfc *sfc, int wr) +{ + u32 fsr = readl(sfc->regbase + SFC_FSR); + int level; + + if (wr) + level = (fsr & SFC_FSR_TXLV_MASK) >> SFC_FSR_TXLV_SHIFT; + else + level = (fsr & SFC_FSR_RXLV_MASK) >> SFC_FSR_RXLV_SHIFT; + + return level; +} + +static int rockchip_sfc_wait_fifo_ready(struct rockchip_sfc *sfc, int wr, u32 timeout) +{ + unsigned long tbase = get_timer(0); + int level; + + while (!(level = rockchip_sfc_get_fifo_level(sfc, wr))) { + if (get_timer(tbase) > timeout) { + debug("%s fifo timeout\n", wr ? "write" : "read"); + return -ETIMEDOUT; + } + udelay(1); + } + + return level; +} + +static void rockchip_sfc_adjust_op_work(struct spi_mem_op *op) +{ + if (unlikely(op->dummy.nbytes && !op->addr.nbytes)) { + /* + * SFC not support output DUMMY cycles right after CMD cycles, so + * treat it as ADDR cycles. + */ + op->addr.nbytes = op->dummy.nbytes; + op->addr.buswidth = op->dummy.buswidth; + op->addr.val = 0xFFFFFFFFF; + + op->dummy.nbytes = 0; + } +} + +static int rockchip_sfc_wait_for_dma_finished(struct rockchip_sfc *sfc, int timeout) +{ + unsigned long tbase; + + /* Wait for the DMA interrupt status */ + tbase = get_timer(0); + while (!(readl(sfc->regbase + SFC_RISR) & SFC_RISR_DMA)) { + if (get_timer(tbase) > timeout) { + printf("dma timeout\n"); + rockchip_sfc_reset(sfc); + + return -ETIMEDOUT; + } + + udelay(1); + } + + writel(0xFFFFFFFF, sfc->regbase + SFC_ICLR); + + return 0; +} + +static int rockchip_sfc_xfer_setup(struct rockchip_sfc *sfc, + struct spi_slave *mem, + const struct spi_mem_op *op, + u32 len) +{ + struct dm_spi_slave_plat *plat = dev_get_parent_plat(mem->dev); + u32 ctrl = 0, cmd = 0; + + /* set CMD */ + cmd = op->cmd.opcode; + ctrl |= ((op->cmd.buswidth >> 1) << SFC_CTRL_CMD_BITS_SHIFT); + + /* set ADDR */ + if (op->addr.nbytes) { + if (op->addr.nbytes == 4) { + cmd |= SFC_CMD_ADDR_32BITS << SFC_CMD_ADDR_SHIFT; + } else if (op->addr.nbytes == 3) { + cmd |= SFC_CMD_ADDR_24BITS << SFC_CMD_ADDR_SHIFT; + } else { + cmd |= SFC_CMD_ADDR_XBITS << SFC_CMD_ADDR_SHIFT; + writel(op->addr.nbytes * 8 - 1, sfc->regbase + SFC_ABIT); + } + + ctrl |= ((op->addr.buswidth >> 1) << SFC_CTRL_ADDR_BITS_SHIFT); + } + + /* set DUMMY */ + if (op->dummy.nbytes) { + if (op->dummy.buswidth == 4) + cmd |= op->dummy.nbytes * 2 << SFC_CMD_DUMMY_SHIFT; + else if (op->dummy.buswidth == 2) + cmd |= op->dummy.nbytes * 4 << SFC_CMD_DUMMY_SHIFT; + else + cmd |= op->dummy.nbytes * 8 << SFC_CMD_DUMMY_SHIFT; + } + + /* set DATA */ + if (sfc->version >= SFC_VER_4) /* Clear it if no data to transfer */ + writel(len, sfc->regbase + SFC_LEN_EXT); + else + cmd |= len << SFC_CMD_TRAN_BYTES_SHIFT; + if (len) { + if (op->data.dir == SPI_MEM_DATA_OUT) + cmd |= SFC_CMD_DIR_WR << SFC_CMD_DIR_SHIFT; + + ctrl |= ((op->data.buswidth >> 1) << SFC_CTRL_DATA_BITS_SHIFT); + } + if (!len && op->addr.nbytes) + cmd |= SFC_CMD_DIR_WR << SFC_CMD_DIR_SHIFT; + + /* set the Controller */ + ctrl |= SFC_CTRL_PHASE_SEL_NEGETIVE; + cmd |= plat->cs << SFC_CMD_CS_SHIFT; + + debug("addr.nbytes=%x(x%d) dummy.nbytes=%x(x%d)\n", + op->addr.nbytes, op->addr.buswidth, + op->dummy.nbytes, op->dummy.buswidth); + debug("ctrl=%x cmd=%x addr=%llx len=%x\n", + ctrl, cmd, op->addr.val, len); + + writel(ctrl, sfc->regbase + SFC_CTRL); + writel(cmd, sfc->regbase + SFC_CMD); + if (op->addr.nbytes) + writel(op->addr.val, sfc->regbase + SFC_ADDR); + + return 0; +} + +static int rockchip_sfc_write_fifo(struct rockchip_sfc *sfc, const u8 *buf, int len) +{ + u8 bytes = len & 0x3; + u32 dwords; + int tx_level; + u32 write_words; + u32 tmp = 0; + + dwords = len >> 2; + while (dwords) { + tx_level = rockchip_sfc_wait_fifo_ready(sfc, SFC_CMD_DIR_WR, 1000); + if (tx_level < 0) + return tx_level; + write_words = min_t(u32, tx_level, dwords); + writesl(sfc->regbase + SFC_DATA, buf, write_words); + buf += write_words << 2; + dwords -= write_words; + } + + /* write the rest non word aligned bytes */ + if (bytes) { + tx_level = rockchip_sfc_wait_fifo_ready(sfc, SFC_CMD_DIR_WR, 1000); + if (tx_level < 0) + return tx_level; + memcpy(&tmp, buf, bytes); + writel(tmp, sfc->regbase + SFC_DATA); + } + + return len; +} + +static int rockchip_sfc_read_fifo(struct rockchip_sfc *sfc, u8 *buf, int len) +{ + u8 bytes = len & 0x3; + u32 dwords; + u8 read_words; + int rx_level; + int tmp; + + /* word aligned access only */ + dwords = len >> 2; + while (dwords) { + rx_level = rockchip_sfc_wait_fifo_ready(sfc, SFC_CMD_DIR_RD, 1000); + if (rx_level < 0) + return rx_level; + read_words = min_t(u32, rx_level, dwords); + readsl(sfc->regbase + SFC_DATA, buf, read_words); + buf += read_words << 2; + dwords -= read_words; + } + + /* read the rest non word aligned bytes */ + if (bytes) { + rx_level = rockchip_sfc_wait_fifo_ready(sfc, SFC_CMD_DIR_RD, 1000); + if (rx_level < 0) + return rx_level; + tmp = readl(sfc->regbase + SFC_DATA); + memcpy(buf, &tmp, bytes); + } + + return len; +} + +static int rockchip_sfc_fifo_transfer_dma(struct rockchip_sfc *sfc, dma_addr_t dma_buf, size_t len) +{ + writel(0xFFFFFFFF, sfc->regbase + SFC_ICLR); + writel((u32)dma_buf, sfc->regbase + SFC_DMA_ADDR); + writel(0x1, sfc->regbase + SFC_DMA_TRIGGER); + + return len; +} + +static int rockchip_sfc_xfer_data_poll(struct rockchip_sfc *sfc, + const struct spi_mem_op *op, u32 len) +{ + debug("xfer_poll len=%x\n", len); + + if (op->data.dir == SPI_MEM_DATA_OUT) + return rockchip_sfc_write_fifo(sfc, op->data.buf.out, len); + else + return rockchip_sfc_read_fifo(sfc, op->data.buf.in, len); +} + +static int rockchip_sfc_xfer_data_dma(struct rockchip_sfc *sfc, + const struct spi_mem_op *op, u32 len) +{ + struct bounce_buffer bb; + unsigned int bb_flags; + void *dma_buf; + int ret; + + debug("xfer_dma len=%x\n", len); + + if (op->data.dir == SPI_MEM_DATA_OUT) { + dma_buf = (void *)op->data.buf.out; + bb_flags = GEN_BB_READ; + } else { + dma_buf = (void *)op->data.buf.in; + bb_flags = GEN_BB_WRITE; + } + + ret = bounce_buffer_start(&bb, dma_buf, len, bb_flags); + if (ret) + return ret; + + ret = rockchip_sfc_fifo_transfer_dma(sfc, (dma_addr_t)bb.bounce_buffer, len); + rockchip_sfc_wait_for_dma_finished(sfc, len * 10); + bounce_buffer_stop(&bb); + + return ret; +} + +static int rockchip_sfc_xfer_done(struct rockchip_sfc *sfc, u32 timeout_us) +{ + unsigned long tbase = get_timer(0); + int ret = 0; + u32 timeout = timeout_us; + + while (readl(sfc->regbase + SFC_SR) & SFC_SR_IS_BUSY) { + if (get_timer(tbase) > timeout) { + printf("wait sfc idle timeout\n"); + rockchip_sfc_reset(sfc); + + return -ETIMEDOUT; + } + + udelay(1); + } + + return ret; +} + +static int rockchip_sfc_exec_op(struct spi_slave *mem, + const struct spi_mem_op *op) +{ + struct rockchip_sfc *sfc = dev_get_plat(mem->dev->parent); + u32 len = min_t(u32, op->data.nbytes, sfc->max_iosize); + int ret; + +#if CONFIG_IS_ENABLED(CLK) + if (unlikely(mem->max_hz != sfc->speed)) { + ret = clk_set_rate(&sfc->clk, clamp(mem->max_hz, (uint)SFC_MIN_SPEED_HZ, + (uint)SFC_MAX_SPEED_HZ)); + if (ret < 0) { + printf("set_freq=%dHz fail, check if it's the cru support level\n", + mem->max_hz); + return ret; + } + + sfc->max_freq = mem->max_hz; + sfc->speed = mem->max_hz; + debug("set_freq=%dHz real_freq=%dHz\n", sfc->max_freq, sfc->speed); + } +#endif + + rockchip_sfc_adjust_op_work((struct spi_mem_op *)op); + + rockchip_sfc_xfer_setup(sfc, mem, op, len); + if (len) { + if (likely(sfc->use_dma) && !(len & 0x3) && len >= SFC_DMA_TRANS_THRETHOLD) + ret = rockchip_sfc_xfer_data_dma(sfc, op, len); + else + ret = rockchip_sfc_xfer_data_poll(sfc, op, len); + + if (ret != len) { + printf("xfer data failed ret %d dir %d\n", ret, op->data.dir); + + return -EIO; + } + } + + return rockchip_sfc_xfer_done(sfc, 100000); +} + +static int rockchip_sfc_adjust_op_size(struct spi_slave *mem, struct spi_mem_op *op) +{ + struct rockchip_sfc *sfc = dev_get_plat(mem->dev->parent); + + op->data.nbytes = min(op->data.nbytes, sfc->max_iosize); + return 0; +} + +static int rockchip_sfc_set_speed(struct udevice *bus, uint speed) +{ + /* We set up speed later for each transmission. + */ + return 0; +} + +static int rockchip_sfc_set_mode(struct udevice *bus, uint mode) +{ + return 0; +} + +static const struct spi_controller_mem_ops rockchip_sfc_mem_ops = { + .adjust_op_size = rockchip_sfc_adjust_op_size, + .exec_op = rockchip_sfc_exec_op, +}; + +static const struct dm_spi_ops rockchip_sfc_ops = { + .mem_ops = &rockchip_sfc_mem_ops, + .set_speed = rockchip_sfc_set_speed, + .set_mode = rockchip_sfc_set_mode, +}; + +static const struct udevice_id rockchip_sfc_ids[] = { + { .compatible = "rockchip,sfc"}, + {}, +}; + +U_BOOT_DRIVER(rockchip_sfc_driver) = { + .name = "rockchip_sfc", + .id = UCLASS_SPI, + .of_match = rockchip_sfc_ids, + .ops = &rockchip_sfc_ops, + .of_to_plat = rockchip_sfc_ofdata_to_platdata, + .plat_auto = sizeof(struct rockchip_sfc), + .probe = rockchip_sfc_probe, +};