diff mbox series

[39/57] arm: Remove mx6dlarm2 board

Message ID 20210221010634.21310-40-trini@konsulko.com
State New
Delegated to: Tom Rini
Headers show
Series Enforce DM_MMC migration and remove platforms | expand

Commit Message

Tom Rini Feb. 21, 2021, 1:06 a.m. UTC
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.

Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ye Li <ye.li@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
---
 arch/arm/mach-imx/mx6/Kconfig               |   4 -
 board/freescale/mx6qarm2/Kconfig            |  12 -
 board/freescale/mx6qarm2/MAINTAINERS        |  10 -
 board/freescale/mx6qarm2/Makefile           |   7 -
 board/freescale/mx6qarm2/imximage.cfg       | 337 --------------
 board/freescale/mx6qarm2/imximage_mx6dl.cfg | 461 --------------------
 board/freescale/mx6qarm2/mx6qarm2.c         | 290 ------------
 configs/mx6dlarm2_defconfig                 |  41 --
 configs/mx6dlarm2_lpddr2_defconfig          |  41 --
 configs/mx6qarm2_defconfig                  |  41 --
 configs/mx6qarm2_lpddr2_defconfig           |  41 --
 include/configs/mx6qarm2.h                  | 127 ------
 12 files changed, 1412 deletions(-)
 delete mode 100644 board/freescale/mx6qarm2/Kconfig
 delete mode 100644 board/freescale/mx6qarm2/MAINTAINERS
 delete mode 100644 board/freescale/mx6qarm2/Makefile
 delete mode 100644 board/freescale/mx6qarm2/imximage.cfg
 delete mode 100644 board/freescale/mx6qarm2/imximage_mx6dl.cfg
 delete mode 100644 board/freescale/mx6qarm2/mx6qarm2.c
 delete mode 100644 configs/mx6dlarm2_defconfig
 delete mode 100644 configs/mx6dlarm2_lpddr2_defconfig
 delete mode 100644 configs/mx6qarm2_defconfig
 delete mode 100644 configs/mx6qarm2_lpddr2_defconfig
 delete mode 100644 include/configs/mx6qarm2.h
diff mbox series

Patch

diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig
index 594923e804c2..b0923ef76edb 100644
--- a/arch/arm/mach-imx/mx6/Kconfig
+++ b/arch/arm/mach-imx/mx6/Kconfig
@@ -287,9 +287,6 @@  config TARGET_MX6MEMCAL
 	  and characterize the memory layout of a new design during the initial
 	  development and pre-production stages.
 
-config TARGET_MX6QARM2
-	bool "mx6qarm2"
-
 config TARGET_MX6DL_MAMOJ
 	bool "Support BTicino Mamoj"
 	depends on MX6QDL
@@ -622,7 +619,6 @@  source "board/compulab/cm_fx6/Kconfig"
 source "board/dhelectronics/dh_imx6/Kconfig"
 source "board/engicam/imx6q/Kconfig"
 source "board/engicam/imx6ul/Kconfig"
-source "board/freescale/mx6qarm2/Kconfig"
 source "board/freescale/mx6memcal/Kconfig"
 source "board/freescale/mx6sabreauto/Kconfig"
 source "board/freescale/mx6sabresd/Kconfig"
diff --git a/board/freescale/mx6qarm2/Kconfig b/board/freescale/mx6qarm2/Kconfig
deleted file mode 100644
index 8ab8b460f92a..000000000000
--- a/board/freescale/mx6qarm2/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@ 
-if TARGET_MX6QARM2
-
-config SYS_BOARD
-	default "mx6qarm2"
-
-config SYS_VENDOR
-	default "freescale"
-
-config SYS_CONFIG_NAME
-	default "mx6qarm2"
-
-endif
diff --git a/board/freescale/mx6qarm2/MAINTAINERS b/board/freescale/mx6qarm2/MAINTAINERS
deleted file mode 100644
index fdbc7fa7254b..000000000000
--- a/board/freescale/mx6qarm2/MAINTAINERS
+++ /dev/null
@@ -1,10 +0,0 @@ 
-MX6QARM2 BOARD
-M:	Jason Liu <jason.hui.liu@nxp.com>
-M:	Ye Li <ye.li@nxp.com>
-S:	Maintained
-F:	board/freescale/mx6qarm2/
-F:	include/configs/mx6qarm2.h
-F:	configs/mx6qarm2_defconfig
-F:	configs/mx6dlarm2_defconfig
-F:	configs/mx6qarm2_lpddr2_defconfig
-F:	configs/mx6dlarm2_lpddr2_defconfig
diff --git a/board/freescale/mx6qarm2/Makefile b/board/freescale/mx6qarm2/Makefile
deleted file mode 100644
index ef80a8967258..000000000000
--- a/board/freescale/mx6qarm2/Makefile
+++ /dev/null
@@ -1,7 +0,0 @@ 
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de>
-#
-# (C) Copyright 2011 Freescale Semiconductor, Inc.
-
-obj-y	:= mx6qarm2.o
diff --git a/board/freescale/mx6qarm2/imximage.cfg b/board/freescale/mx6qarm2/imximage.cfg
deleted file mode 100644
index 74a33c25032a..000000000000
--- a/board/freescale/mx6qarm2/imximage.cfg
+++ /dev/null
@@ -1,337 +0,0 @@ 
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2011-2014 Freescale Semiconductor, Inc.
- * Jason Liu <r64343@freescale.com>
- *
- * Refer doc/imx/mkimage/imximage.txt for more details about how-to configure
- * and create imximage boot image
- *
- * The syntax is taken as close as possible with the kwbimage
- */
-
-/* image version */
-IMAGE_VERSION 2
-
-/*
- * Boot Device : one of
- * spi, sd (the board has no nand neither onenand)
- */
-BOOT_FROM	sd
-
-/*
- * Device Configuration Data (DCD)
- *
- * Each entry must have the format:
- * Addr-type           Address        Value
- *
- * where:
- *	Addr-type register length (1,2 or 4 bytes)
- *	Address	  absolute address of the register
- *	value	  value to be stored in the register
- */
-#ifdef CONFIG_MX6DQ_LPDDR2
-/* DCD */
-DATA 4 0x020C4018 0x60324
-
-DATA 4 0x020E05a8 0x00003038
-DATA 4 0x020E05b0 0x00003038
-DATA 4 0x020E0524 0x00003038
-DATA 4 0x020E051c 0x00003038
-
-DATA 4 0x020E0518 0x00003038
-DATA 4 0x020E050c 0x00003038
-DATA 4 0x020E05b8 0x00003038
-DATA 4 0x020E05c0 0x00003038
-
-DATA 4 0x020E05ac 0x00000038
-DATA 4 0x020E05b4 0x00000038
-DATA 4 0x020E0528 0x00000038
-DATA 4 0x020E0520 0x00000038
-
-DATA 4 0x020E0514 0x00000038
-DATA 4 0x020E0510 0x00000038
-DATA 4 0x020E05bc 0x00000038
-DATA 4 0x020E05c4 0x00000038
-
-DATA 4 0x020E056c 0x00000038
-DATA 4 0x020E0578 0x00000038
-DATA 4 0x020E0588 0x00000038
-DATA 4 0x020E0594 0x00000038
-
-DATA 4 0x020E057c 0x00000038
-DATA 4 0x020E0590 0x00000038
-DATA 4 0x020E0598 0x00000038
-DATA 4 0x020E058c 0x00000000
-
-DATA 4 0x020E059c 0x00000038
-DATA 4 0x020E05a0 0x00000038
-DATA 4 0x020E0784 0x00000038
-DATA 4 0x020E0788 0x00000038
-
-DATA 4 0x020E0794 0x00000038
-DATA 4 0x020E079c 0x00000038
-DATA 4 0x020E07a0 0x00000038
-DATA 4 0x020E07a4 0x00000038
-
-DATA 4 0x020E07a8 0x00000038
-DATA 4 0x020E0748 0x00000038
-DATA 4 0x020E074c 0x00000038
-DATA 4 0x020E0750 0x00020000
-
-DATA 4 0x020E0758 0x00000000
-DATA 4 0x020E0774 0x00020000
-DATA 4 0x020E078c 0x00000038
-DATA 4 0x020E0798 0x00080000
-
-DATA 4 0x021b001c 0x00008000
-DATA 4 0x021b401c 0x00008000
-
-DATA 4 0x021b085c 0x1b5f01ff
-DATA 4 0x021b485c 0x1b5f01ff
-
-DATA 4 0x021b0800 0xa1390000
-DATA 4 0x021b4800 0xa1390000
-
-DATA 4 0x021b0890 0x00400000
-DATA 4 0x021b4890 0x00400000
-
-DATA 4 0x021b48bc 0x00055555
-
-DATA 4 0x021b08b8 0x00000800
-DATA 4 0x021b48b8 0x00000800
-
-DATA 4 0x021b081c 0x33333333
-DATA 4 0x021b0820 0x33333333
-DATA 4 0x021b0824 0x33333333
-DATA 4 0x021b0828 0x33333333
-DATA 4 0x021b481c 0x33333333
-DATA 4 0x021b4820 0x33333333
-DATA 4 0x021b4824 0x33333333
-DATA 4 0x021b4828 0x33333333
-
-DATA 4 0x021b082c 0xf3333333
-DATA 4 0x021b0830 0xf3333333
-DATA 4 0x021b0834 0xf3333333
-DATA 4 0x021b0838 0xf3333333
-DATA 4 0x021b482c 0xf3333333
-DATA 4 0x021b4830 0xf3333333
-DATA 4 0x021b4834 0xf3333333
-DATA 4 0x021b4838 0xf3333333
-
-DATA 4 0x021b0848 0x49383b39
-DATA 4 0x021b0850 0x30364738
-DATA 4 0x021b4848 0x3e3c3846
-DATA 4 0x021b4850 0x4c294b35
-
-DATA 4 0x021b083c 0x20000000
-DATA 4 0x021b0840 0x0
-DATA 4 0x021b483c 0x20000000
-DATA 4 0x021b4840 0x0
-
-DATA 4 0x021b0858 0xf00
-DATA 4 0x021b4858 0xf00
-
-DATA 4 0x021b08b8 0x800
-DATA 4 0x021b48b8 0x800
-
-DATA 4 0x021b000c 0x555a61a5
-DATA 4 0x021b0004 0x20036
-DATA 4 0x021b0010 0x160e83
-DATA 4 0x021b0014 0xdd
-DATA 4 0x021b0018 0x8174c
-DATA 4 0x021b002c 0xf9f26d2
-DATA 4 0x021b0030 0x20e
-DATA 4 0x021b0038 0x200aac
-DATA 4 0x021b0008 0x0
-
-DATA 4 0x021b0040 0x5f
-
-DATA 4 0x021b0000 0xc3010000
-
-DATA 4 0x021b400c 0x555a61a5
-DATA 4 0x021b4004 0x20036
-DATA 4 0x021b4010 0x160e83
-DATA 4 0x021b4014 0xdd
-DATA 4 0x021b4018 0x8174c
-DATA 4 0x021b402c 0xf9f26d2
-DATA 4 0x021b4030 0x20e
-DATA 4 0x021b4038 0x200aac
-DATA 4 0x021b4008 0x0
-
-DATA 4 0x021b4040 0x3f
-DATA 4 0x021b4000 0xc3010000
-
-DATA 4 0x021b001c 0x3f8030
-DATA 4 0x021b001c 0xff0a8030
-DATA 4 0x021b001c 0xc2018030
-DATA 4 0x021b001c 0x6028030
-DATA 4 0x021b001c 0x2038030
-
-DATA 4 0x021b401c 0x3f8030
-DATA 4 0x021b401c 0xff0a8030
-DATA 4 0x021b401c 0xc2018030
-DATA 4 0x021b401c 0x6028030
-DATA 4 0x021b401c 0x2038030
-
-DATA 4 0x021b0800 0xa1390003
-DATA 4 0x021b4800 0xa1390003
-
-DATA 4 0x021b0020 0x7800
-DATA 4 0x021b4020 0x7800
-
-DATA 4 0x021b0818 0x0
-DATA 4 0x021b4818 0x0
-
-DATA 4 0x021b0800 0xa1390003
-DATA 4 0x021b4800 0xa1390003
-
-DATA 4 0x021b08b8 0x800
-DATA 4 0x021b48b8 0x800
-
-DATA 4 0x021b001c 0x0
-DATA 4 0x021b401c 0x0
-
-DATA 4 0x021b0404 0x00011006
-
-DATA 4 0x020c4068 0x00C03F3F
-DATA 4 0x020c406c 0x0030FC03
-DATA 4 0x020c4070 0x0FFFC000
-DATA 4 0x020c4074 0x3FF00000
-DATA 4 0x020c4078 0x00FFF300
-DATA 4 0x020c407c 0x0F0000C3
-DATA 4 0x020c4080 0x000003FF
-
-/* enable AXI cache for VDOA/VPU/IPU */
-DATA 4 0x020e0010 0xF00000CF
-/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
-DATA 4 0x020e0018 0x007F007F
-DATA 4 0x020e001c 0x007F007F
-
-#else
-DATA 4 0x020e05a8 0x00000030
-DATA 4 0x020e05b0 0x00000030
-DATA 4 0x020e0524 0x00000030
-DATA 4 0x020e051c 0x00000030
-
-DATA 4 0x020e0518 0x00000030
-DATA 4 0x020e050c 0x00000030
-DATA 4 0x020e05b8 0x00000030
-DATA 4 0x020e05c0 0x00000030
-
-DATA 4 0x020e05ac 0x00020030
-DATA 4 0x020e05b4 0x00020030
-DATA 4 0x020e0528 0x00020030
-DATA 4 0x020e0520 0x00020030
-
-DATA 4 0x020e0514 0x00020030
-DATA 4 0x020e0510 0x00020030
-DATA 4 0x020e05bc 0x00020030
-DATA 4 0x020e05c4 0x00020030
-
-DATA 4 0x020e056c 0x00020030
-DATA 4 0x020e0578 0x00020030
-DATA 4 0x020e0588 0x00020030
-DATA 4 0x020e0594 0x00020030
-
-DATA 4 0x020e057c 0x00020030
-DATA 4 0x020e0590 0x00003000
-DATA 4 0x020e0598 0x00003000
-DATA 4 0x020e058c 0x00000000
-
-DATA 4 0x020e059c 0x00003030
-DATA 4 0x020e05a0 0x00003030
-DATA 4 0x020e0784 0x00000030
-DATA 4 0x020e0788 0x00000030
-
-DATA 4 0x020e0794 0x00000030
-DATA 4 0x020e079c 0x00000030
-DATA 4 0x020e07a0 0x00000030
-DATA 4 0x020e07a4 0x00000030
-
-DATA 4 0x020e07a8 0x00000030
-DATA 4 0x020e0748 0x00000030
-DATA 4 0x020e074c 0x00000030
-DATA 4 0x020e0750 0x00020000
-
-DATA 4 0x020e0758 0x00000000
-DATA 4 0x020e0774 0x00020000
-DATA 4 0x020e078c 0x00000030
-DATA 4 0x020e0798 0x000C0000
-
-DATA 4 0x021b081c 0x33333333
-DATA 4 0x021b0820 0x33333333
-DATA 4 0x021b0824 0x33333333
-DATA 4 0x021b0828 0x33333333
-
-DATA 4 0x021b481c 0x33333333
-DATA 4 0x021b4820 0x33333333
-DATA 4 0x021b4824 0x33333333
-DATA 4 0x021b4828 0x33333333
-
-DATA 4 0x021b0018 0x00081740
-
-DATA 4 0x021b001c 0x00008000
-DATA 4 0x021b000c 0x555A7975
-DATA 4 0x021b0010 0xFF538E64
-DATA 4 0x021b0014 0x01FF00DB
-DATA 4 0x021b002c 0x000026D2
-
-DATA 4 0x021b0030 0x005B0E21
-DATA 4 0x021b0008 0x09444040
-DATA 4 0x021b0004 0x00025576
-DATA 4 0x021b0040 0x00000027
-DATA 4 0x021b0000 0xC31A0000
-
-DATA 4 0x021b001c 0x04088032
-DATA 4 0x021b001c 0x0408803A
-DATA 4 0x021b001c 0x00008033
-DATA 4 0x021b001c 0x0000803B
-DATA 4 0x021b001c 0x00428031
-DATA 4 0x021b001c 0x00428039
-DATA 4 0x021b001c 0x09408030
-DATA 4 0x021b001c 0x09408038
-
-DATA 4 0x021b001c 0x04008040
-DATA 4 0x021b001c 0x04008048
-DATA 4 0x021b0800 0xA1380003
-DATA 4 0x021b4800 0xA1380003
-DATA 4 0x021b0020 0x00005800
-DATA 4 0x021b0818 0x00022227
-DATA 4 0x021b4818 0x00022227
-
-DATA 4 0x021b083c 0x434B0350
-DATA 4 0x021b0840 0x034C0359
-DATA 4 0x021b483c 0x434B0350
-DATA 4 0x021b4840 0x03650348
-DATA 4 0x021b0848 0x4436383B
-DATA 4 0x021b4848 0x39393341
-DATA 4 0x021b0850 0x35373933
-DATA 4 0x021b4850 0x48254A36
-
-DATA 4 0x021b080c 0x001F001F
-DATA 4 0x021b0810 0x001F001F
-
-DATA 4 0x021b480c 0x00440044
-DATA 4 0x021b4810 0x00440044
-
-DATA 4 0x021b08b8 0x00000800
-DATA 4 0x021b48b8 0x00000800
-
-DATA 4 0x021b001c 0x00000000
-DATA 4 0x021b0404 0x00011006
-
-DATA 4 0x020c4068 0x00C03F3F
-DATA 4 0x020c406c 0x0030FC03
-DATA 4 0x020c4070 0x0FFFC000
-DATA 4 0x020c4074 0x3FF00000
-DATA 4 0x020c4078 0x00FFF300
-DATA 4 0x020c407c 0x0F0000C3
-DATA 4 0x020c4080 0x000003FF
-
-/* enable AXI cache for VDOA/VPU/IPU */
-DATA 4 0x020e0010 0xF00000CF
-/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
-DATA 4 0x020e0018 0x007F007F
-DATA 4 0x020e001c 0x007F007F
-
-#endif /* CONFIG_MX6DQ_LPDDR2 */
diff --git a/board/freescale/mx6qarm2/imximage_mx6dl.cfg b/board/freescale/mx6qarm2/imximage_mx6dl.cfg
deleted file mode 100644
index 0d1353119ba1..000000000000
--- a/board/freescale/mx6qarm2/imximage_mx6dl.cfg
+++ /dev/null
@@ -1,461 +0,0 @@ 
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2014 Freescale Semiconductor, Inc.
- * Jason Liu <r64343@freescale.com>
- *
- * Refer doc/imx/mkimage/imximage.txt for more details about how-to configure
- * and create imximage boot image
- *
- * The syntax is taken as close as possible with the kwbimage
- */
-
-/* image version */
-IMAGE_VERSION 2
-
-/*
- * Boot Device : one of
- * spi, sd (the board has no nand neither onenand)
- */
-BOOT_FROM	sd
-
-/*
- * Device Configuration Data (DCD)
- *
- * Each entry must have the format:
- * Addr-type           Address        Value
- *
- * where:
- *	Addr-type register length (1,2 or 4 bytes)
- *	Address	  absolute address of the register
- *	value	  value to be stored in the register
- */
-
-
-
-#ifdef CONFIG_MX6DL_LPDDR2
-
-/* IOMUX SETTINGS */
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS0 */
-DATA 4 0x020E04bc 0x00003028
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS1 */
-DATA 4 0x020E04c0 0x00003028
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS2 */
-DATA 4 0x020E04c4 0x00003028
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS3 */
-DATA 4 0x020E04c8 0x00003028
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS4 */
-DATA 4 0x020E04cc 0x00003028
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS5 */
-DATA 4 0x020E04d0 0x00003028
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS6 */
-DATA 4 0x020E04d4 0x00003028
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS7 */
-DATA 4 0x020E04d8 0x00003028
-
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM0 */
-DATA 4 0x020E0470 0x00000038
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM1 */
-DATA 4 0x020E0474 0x00000038
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM2 */
-DATA 4 0x020E0478 0x00000038
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM3 */
-DATA 4 0x020E047c 0x00000038
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM4 */
-DATA 4 0x020E0480 0x00000038
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM5 */
-DATA 4 0x020E0484 0x00000038
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM6 */
-DATA 4 0x020E0488 0x00000038
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM7 */
-DATA 4 0x020E048c 0x00000038
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_CAS */
-DATA 4 0x020E0464 0x00000038
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_RAS */
-DATA 4 0x020E0490 0x00000038
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDCLK_0 */
-DATA 4 0x020E04ac 0x00000038
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDCLK_1 */
-DATA 4 0x020E04b0 0x00000038
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_RESET */
-DATA 4 0x020E0494 0x00000038
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDCKE0 */
-DATA 4 0x020E04a4 0x00000038
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDCKE1 */
-DATA 4 0x020E04a8 0x00000038
-/*
- * IOMUXC_SW_PAD_CTL_PAD_DRAM_SDBA2
- * DSE can be configured using Group Control Register:
- * IOMUXC_SW_PAD_CTL_GRP_CTLDS
- */
-DATA 4 0x020E04a0 0x00000000
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDODT0 */
-DATA 4 0x020E04b4 0x00000038
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDODT1 */
-DATA 4 0x020E04b8 0x00000038
-/* IOMUXC_SW_PAD_CTL_GRP_B0DS */
-DATA 4 0x020E0764 0x00000038
-/* IOMUXC_SW_PAD_CTL_GRP_B1DS */
-DATA 4 0x020E0770 0x00000038
-/* IOMUXC_SW_PAD_CTL_GRP_B2DS */
-DATA 4 0x020E0778 0x00000038
-/* IOMUXC_SW_PAD_CTL_GRP_B3DS */
-DATA 4 0x020E077c 0x00000038
-/* IOMUXC_SW_PAD_CTL_GRP_B4DS */
-DATA 4 0x020E0780 0x00000038
-/* IOMUXC_SW_PAD_CTL_GRP_B5DS */
-DATA 4 0x020E0784 0x00000038
-/* IOMUXC_SW_PAD_CTL_GRP_B6DS */
-DATA 4 0x020E078c 0x00000038
-/* IOMUXC_SW_PAD_CTL_GRP_B7DS */
-DATA 4 0x020E0748 0x00000038
-/* IOMUXC_SW_PAD_CTL_GRP_ADDDS */
-DATA 4 0x020E074c 0x00000038
-/* IOMUXC_SW_PAD_CTL_GRP_CTLDS */
-DATA 4 0x020E076c 0x00000038
-/* IOMUXC_SW_PAD_CTL_GRP_DDRMODE_CTL */
-DATA 4 0x020E0750 0x00020000
-/* IOMUXC_SW_PAD_CTL_GRP_DDRPKE */
-DATA 4 0x020E0754 0x00000000
-/* IOMUXC_SW_PAD_CTL_GRP_DDRMODE */
-DATA 4 0x020E0760 0x00020000
-/* IOMUXC_SW_PAD_CTL_GRP_DDR_TYPE */
-DATA 4 0x020E0774 0x00080000
-
-/*
- * DDR Controller Registers
- *
- * Manufacturer:	Mocron
- * Device Part Number:	MT42L64M64D2KH-18
- * Clock Freq.: 	528MHz
- * MMDC channels: Both MMDC0, MMDC1
- *Density per CS in Gb: 	256M
- * Chip Selects used:	2
- * Number of Banks:	8
- * Row address:    	14
- * Column address: 	9
- * Data bus width	32
- */
-
-/* MMDC_P0_BASE_ADDR = 0x021b0000 */
-/* MMDC_P1_BASE_ADDR = 0x021b4000 */
-
-/* MMDC0_MDSCR, set the Configuration request bit during MMDC set up */
-DATA 4 0x021b001c 0x00008000
-
-/* MMDC0_MDSCR, set the Configuration request bit during MMDC set up */
-DATA 4 0x021b401c 0x00008000
-
-/*LPDDR2 ZQ params */
-DATA 4 0x021b085c 0x1b5f01ff
-DATA 4 0x021b485c 0x1b5f01ff
-
-/* Calibration setup. */
-/* DDR_PHY_P0_MPZQHWCTRL, enable on time ZQ calibration */
-DATA 4 0x021b0800 0xa1390003
-
-/*ca bus abs delay */
-DATA 4 0x021b0890 0x00400000
-/*ca bus abs delay */
-DATA 4 0x021b4890 0x00400000
-/* values of 20,40,50,60,7f tried. no difference seen */
-
-/* DDR_PHY_P1_MPWRCADL */
-DATA 4 0x021b48bc 0x00055555
-
-/*frc_msr.*/
-DATA 4 0x021b08b8 0x00000800
-/*frc_msr.*/
-DATA 4 0x021b48b8 0x00000800
-
-/* DDR_PHY_P0_MPREDQBY0DL3 */
-DATA 4 0x021b081c 0x33333333
-/* DDR_PHY_P0_MPREDQBY1DL3 */
-DATA 4 0x021b0820 0x33333333
-/* DDR_PHY_P0_MPREDQBY2DL3 */
-DATA 4 0x021b0824 0x33333333
-/* DDR_PHY_P0_MPREDQBY3DL3 */
-DATA 4 0x021b0828 0x33333333
-/* DDR_PHY_P1_MPREDQBY0DL3 */
-DATA 4 0x021b481c 0x33333333
-/* DDR_PHY_P1_MPREDQBY1DL3 */
-DATA 4 0x021b4820 0x33333333
-/* DDR_PHY_P1_MPREDQBY2DL3 */
-DATA 4 0x021b4824 0x33333333
-/* DDR_PHY_P1_MPREDQBY3DL3 */
-DATA 4 0x021b4828 0x33333333
-
-/*
- * Read and write data delay, per byte.
- * For optimized DDR operation it is recommended to run mmdc_calibration
- * on your board, and replace 4 delay register assigns with resulted values
- * Note:
- * a. DQS gating is not relevant for LPDDR2. DSQ gating calibration section
- *    should be skipped, or the write/read calibration comming after that
- *    will stall
- * b. The calibration code that runs for both MMDC0 & MMDC1 should be used.
- */
-
-DATA 4 0x021b0848 0x4b4b524f
-DATA 4 0x021b4848 0x494f4c44
-
-DATA 4 0x021b0850 0x3c3d303c
-DATA 4 0x021b4850 0x3c343d38
-
-/*dqs gating dis */
-DATA 4 0x021b083c 0x20000000
-DATA 4 0x021b0840 0x0
-DATA 4 0x021b483c 0x20000000
-DATA 4 0x021b4840 0x0
-
-/*clk delay */
-DATA 4 0x021b0858 0xa00
-/*clk delay */
-DATA 4 0x021b4858 0xa00
-
-/*frc_msr */
-DATA 4 0x021b08b8 0x00000800
-/*frc_msr */
-DATA 4 0x021b48b8 0x00000800
-/* Calibration setup end */
-
-/* Channel0 - startng address 0x80000000 */
-/* MMDC0_MDCFG0 */
-DATA 4 0x021b000c 0x34386145
-
-/* MMDC0_MDPDC */
-DATA 4 0x021b0004 0x00020036
-/* MMDC0_MDCFG1 */
-DATA 4 0x021b0010 0x00100c83
-/* MMDC0_MDCFG2 */
-DATA 4 0x021b0014 0x000000Dc
-/* MMDC0_MDMISC */
-DATA 4 0x021b0018 0x0000174C
-/* MMDC0_MDRWD;*/
-DATA 4 0x021b002c 0x0f9f26d2
-/* MMDC0_MDOR */
-DATA 4 0x021b0030 0x009f0e10
-/* MMDC0_MDCFG3LP */
-DATA 4 0x021b0038 0x00190778
-/* MMDC0_MDOTC */
-DATA 4 0x021b0008 0x00000000
-
-/* CS0_END */
-DATA 4 0x021b0040 0x0000005f
-/* ROC */
-DATA 4 0x021b0404 0x0000000f
-
-/* MMDC0_MDCTL */
-DATA 4 0x021b0000 0xc3010000
-
-/* Channel1 - starting address 0x10000000 */
-/* MMDC1_MDCFG0 */
-DATA 4 0x021b400c 0x34386145
-
-/* MMDC1_MDPDC */
-DATA 4 0x021b4004 0x00020036
-/* MMDC1_MDCFG1 */
-DATA 4 0x021b4010 0x00100c83
-/* MMDC1_MDCFG2 */
-DATA 4 0x021b4014 0x000000Dc
-/* MMDC1_MDMISC */
-DATA 4 0x021b4018 0x0000174C
-/* MMDC1_MDRWD;*/
-DATA 4 0x021b402c 0x0f9f26d2
-/* MMDC1_MDOR */
-DATA 4 0x021b4030 0x009f0e10
-/* MMDC1_MDCFG3LP */
-DATA 4 0x021b4038 0x00190778
-/* MMDC1_MDOTC */
-DATA 4 0x021b4008 0x00000000
-
-/* CS0_END */
-DATA 4 0x021b4040 0x0000003f
-
-/* MMDC1_MDCTL */
-DATA 4 0x021b4000 0xc3010000
-
-/* Channel0 : Configure DDR device:*/
-/* MRW: BA=0 CS=0 MR_ADDR=63 MR_OP=0 */
-DATA 4 0x021b001c 0x003f8030
-/* MRW: BA=0 CS=0 MR_ADDR=10 MR_OP=ff */
-DATA 4 0x021b001c 0xff0a8030
-/* MRW: BA=0 CS=0 MR_ADDR=1  MR_OP=a2 */
-DATA 4 0x021b001c 0xa2018030
-/* MRW: BA=0 CS=0 MR_ADDR=2  MR_OP=6. tcl=8, tcwl=4 */
-DATA 4 0x021b001c 0x06028030
-/* MRW: BA=0 CS=0 MR_ADDR=3  MR_OP=2.drive=240/6 */
-DATA 4 0x021b001c 0x01038030
-
-/* Channel1 : Configure DDR device:*/
-/* MRW: BA=0 CS=0 MR_ADDR=63 MR_OP=0 */
-DATA 4 0x021b401c 0x003f8030
-/* MRW: BA=0 CS=0 MR_ADDR=10 MR_OP=ff */
-DATA 4 0x021b401c 0xff0a8030
-/* MRW: BA=0 CS=0 MR_ADDR=1  MR_OP=a2 */
-DATA 4 0x021b401c 0xa2018030
-/* MRW: BA=0 CS=0 MR_ADDR=2  MR_OP=6. tcl=8, tcwl=4 */
-DATA 4 0x021b401c 0x06028030
-/* MRW: BA=0 CS=0 MR_ADDR=3  MR_OP=2.drive=240/6 */
-DATA 4 0x021b401c 0x01038030
-
-/* MMDC0_MDREF */
-DATA 4 0x021b0020 0x00005800
-/* MMDC1_MDREF */
-DATA 4 0x021b4020 0x00005800
-
-/* DDR_PHY_P0_MPODTCTRL */
-DATA 4 0x021b0818 0x0
-/* DDR_PHY_P1_MPODTCTRL */
-DATA 4 0x021b4818 0x0
-
-/*
- * calibration values based on calibration compare of 0x00ffff00:
- * Note, these calibration values are based on Freescale's board
- * May need to run calibration on target board to fine tune these
- */
-
-/* DDR_PHY_P0_MPZQHWCTRL, enable automatic ZQ calibration */
-DATA 4 0x021b0800 0xa1310003
-
-/* DDR_PHY_P0_MPMUR0, frc_msr */
-DATA 4 0x021b08b8 0x00000800
-/* DDR_PHY_P1_MPMUR0, frc_msr */
-DATA 4 0x021b48b8 0x00000800
-
-/*
- * MMDC0_MDSCR, clear this register
- * (especially the configuration bit as initialization is complete)
- */
-DATA 4 0x021b001c 0x00000000
-/*
- * MMDC0_MDSCR, clear this register
- * (especially the configuration bit as initialization is complete)
- */
-DATA 4 0x021b401c 0x00000000
-
-DATA 4 0x020c4068 0x00C03F3F
-DATA 4 0x020c406c 0x0030FC03
-DATA 4 0x020c4070 0x0FFFC000
-DATA 4 0x020c4074 0x3FF00000
-DATA 4 0x020c4078 0x00FFF300
-DATA 4 0x020c407c 0x0F0000C3
-DATA 4 0x020c4080 0x000003FF
-
-DATA 4 0x020e0010 0xF00000CF
-DATA 4 0x020e0018 0x007F007F
-DATA 4 0x020e001c 0x007F007F
-
-#else /* CONFIG_MX6DL_LPDDR2 */
-
-DATA 4 0x020e0798 0x000c0000
-DATA 4 0x020e0758 0x00000000
-DATA 4 0x020e0588 0x00000030
-DATA 4 0x020e0594 0x00000030
-DATA 4 0x020e056c 0x00000030
-DATA 4 0x020e0578 0x00000030
-DATA 4 0x020e074c 0x00000030
-DATA 4 0x020e057c 0x00000030
-DATA 4 0x020e0590 0x00003000
-DATA 4 0x020e0598 0x00003000
-DATA 4 0x020e058c 0x00000000
-DATA 4 0x020e059c 0x00003030
-DATA 4 0x020e05a0 0x00003030
-DATA 4 0x020e078c 0x00000030
-DATA 4 0x020e0750 0x00020000
-DATA 4 0x020e05a8 0x00000030
-DATA 4 0x020e05b0 0x00000030
-DATA 4 0x020e0524 0x00000030
-DATA 4 0x020e051c 0x00000030
-DATA 4 0x020e0518 0x00000030
-DATA 4 0x020e050c 0x00000030
-DATA 4 0x020e05b8 0x00000030
-DATA 4 0x020e05c0 0x00000030
-DATA 4 0x020e0774 0x00020000
-DATA 4 0x020e0784 0x00000030
-DATA 4 0x020e0788 0x00000030
-DATA 4 0x020e0794 0x00000030
-DATA 4 0x020e079c 0x00000030
-DATA 4 0x020e07a0 0x00000030
-DATA 4 0x020e07a4 0x00000030
-DATA 4 0x020e07a8 0x00000030
-DATA 4 0x020e0748 0x00000030
-DATA 4 0x020e05ac 0x00000030
-DATA 4 0x020e05b4 0x00000030
-DATA 4 0x020e0528 0x00000030
-DATA 4 0x020e0520 0x00000030
-DATA 4 0x020e0514 0x00000030
-DATA 4 0x020e0510 0x00000030
-DATA 4 0x020e05bc 0x00000030
-DATA 4 0x020e05c4 0x00000030
-
-DATA 4 0x021b0800 0xa1390003
-DATA 4 0x021b4800 0xa1390003
-DATA 4 0x021b080c 0x001F001F
-DATA 4 0x021b0810 0x001F001F
-DATA 4 0x021b480c 0x00370037
-DATA 4 0x021b4810 0x00370037
-DATA 4 0x021b083c 0x422f0220
-DATA 4 0x021b0840 0x021f0219
-DATA 4 0x021b483C 0x422f0220
-DATA 4 0x021b4840 0x022d022f
-DATA 4 0x021b0848 0x47494b49
-DATA 4 0x021b4848 0x48484c47
-DATA 4 0x021b0850 0x39382b2f
-DATA 4 0x021b4850 0x2f35312c
-DATA 4 0x021b081c 0x33333333
-DATA 4 0x021b0820 0x33333333
-DATA 4 0x021b0824 0x33333333
-DATA 4 0x021b0828 0x33333333
-DATA 4 0x021b481c 0x33333333
-DATA 4 0x021b4820 0x33333333
-DATA 4 0x021b4824 0x33333333
-DATA 4 0x021b4828 0x33333333
-DATA 4 0x021b08b8 0x00000800
-DATA 4 0x021b48b8 0x00000800
-DATA 4 0x021b0004 0x0002002d
-DATA 4 0x021b0008 0x00333030
-
-DATA 4 0x021b000c 0x40445323
-DATA 4 0x021b0010 0xb66e8c63
-
-DATA 4 0x021b0014 0x01ff00db
-DATA 4 0x021b0018 0x00081740
-DATA 4 0x021b001c 0x00008000
-DATA 4 0x021b002c 0x000026d2
-DATA 4 0x021b0030 0x00440e21
-#ifdef CONFIG_DDR_32BIT
-DATA 4 0x021b0040 0x00000017
-DATA 4 0x021b0000 0xc3190000
-#else
-DATA 4 0x021b0040 0x00000027
-DATA 4 0x021b0000 0xc31a0000
-#endif
-DATA 4 0x021b001c 0x04008032
-DATA 4 0x021b001c 0x0400803a
-DATA 4 0x021b001c 0x00008033
-DATA 4 0x021b001c 0x0000803b
-DATA 4 0x021b001c 0x00428031
-DATA 4 0x021b001c 0x00428039
-DATA 4 0x021b001c 0x07208030
-DATA 4 0x021b001c 0x07208038
-DATA 4 0x021b001c 0x04008040
-DATA 4 0x021b001c 0x04008048
-DATA 4 0x021b0020 0x00005800
-DATA 4 0x021b0818 0x00000007
-DATA 4 0x021b4818 0x00000007
-DATA 4 0x021b0004 0x0002556d
-DATA 4 0x021b4004 0x00011006
-DATA 4 0x021b001c 0x00000000
-
-DATA 4 0x020c4068 0x00C03F3F
-DATA 4 0x020c406c 0x0030FC03
-DATA 4 0x020c4070 0x0FFFC000
-DATA 4 0x020c4074 0x3FF00000
-DATA 4 0x020c4078 0x00FFF300
-DATA 4 0x020c407c 0x0F0000C3
-DATA 4 0x020c4080 0x000003FF
-
-DATA 4 0x020e0010 0xF00000CF
-DATA 4 0x020e0018 0x007F007F
-DATA 4 0x020e001c 0x007F007F
-#endif /* CONFIG_MX6DL_LPDDR2 */
diff --git a/board/freescale/mx6qarm2/mx6qarm2.c b/board/freescale/mx6qarm2/mx6qarm2.c
deleted file mode 100644
index c06fd643677d..000000000000
--- a/board/freescale/mx6qarm2/mx6qarm2.c
+++ /dev/null
@@ -1,290 +0,0 @@ 
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <init.h>
-#include <net.h>
-#include <asm/global_data.h>
-#include <asm/io.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/mx6-pins.h>
-#include <asm/arch/clock.h>
-#include <linux/errno.h>
-#include <asm/gpio.h>
-#include <asm/mach-imx/iomux-v3.h>
-#include <mmc.h>
-#include <fsl_esdhc_imx.h>
-#include <miiphy.h>
-#include <netdev.h>
-#include <usb.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
-	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |			\
-	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
-
-#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP |			\
-	PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |			\
-	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
-
-#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
-	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
-
-int dram_init(void)
-{
-#if defined(CONFIG_MX6DL) && !defined(CONFIG_MX6DL_LPDDR2) && \
-	defined(CONFIG_DDR_32BIT)
-	gd->ram_size = ((phys_size_t)CONFIG_DDR_MB * 1024 * 1024) / 2;
-#else
-	gd->ram_size = (phys_size_t)CONFIG_DDR_MB * 1024 * 1024;
-#endif
-
-	return 0;
-}
-
-iomux_v3_cfg_t const uart4_pads[] = {
-	MX6_PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-	MX6_PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const usdhc3_pads[] = {
-	MX6_PAD_SD3_CLK__SD3_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD3_CMD__SD3_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_NANDF_CS0__GPIO6_IO11  | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
-};
-
-iomux_v3_cfg_t const usdhc4_pads[] = {
-	MX6_PAD_SD4_CLK__SD4_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_CMD__SD4_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const enet_pads[] = {
-	MX6_PAD_KEY_COL1__ENET_MDIO        | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_KEY_COL2__ENET_MDC         | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_TXC__RGMII_TXC  | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_TD0__RGMII_TD0  | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_TD1__RGMII_TD1  | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_TD2__RGMII_TD2  | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_TD3__RGMII_TD3  | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET_REF_CLK__ENET_TX_CLK  | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_RXC__RGMII_RXC  | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_RD0__RGMII_RD0  | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_RD1__RGMII_RD1  | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_RD2__RGMII_RD2  | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_RD3__RGMII_RD3  | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
-};
-
-
-static void setup_iomux_uart(void)
-{
-	imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
-}
-
-static void setup_iomux_enet(void)
-{
-	imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
-}
-
-#ifdef CONFIG_FSL_ESDHC_IMX
-struct fsl_esdhc_cfg usdhc_cfg[2] = {
-	{USDHC3_BASE_ADDR},
-	{USDHC4_BASE_ADDR},
-};
-
-int board_mmc_get_env_dev(int devno)
-{
-	return devno - 2;
-}
-
-int board_mmc_getcd(struct mmc *mmc)
-{
-	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
-	int ret;
-
-	if (cfg->esdhc_base == USDHC3_BASE_ADDR) {
-		gpio_direction_input(IMX_GPIO_NR(6, 11));
-		ret = !gpio_get_value(IMX_GPIO_NR(6, 11));
-	} else /* Don't have the CD GPIO pin on board */
-		ret = 1;
-
-	return ret;
-}
-
-int board_mmc_init(struct bd_info *bis)
-{
-	int ret;
-	u32 index = 0;
-
-	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
-	usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
-
-	for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) {
-		switch (index) {
-		case 0:
-			imx_iomux_v3_setup_multiple_pads(
-				usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
-			break;
-		case 1:
-			imx_iomux_v3_setup_multiple_pads(
-				usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
-			break;
-		default:
-			printf("Warning: you configured more USDHC controllers"
-				"(%d) then supported by the board (%d)\n",
-				index + 1, CONFIG_SYS_FSL_USDHC_NUM);
-			return -EINVAL;
-		}
-
-		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[index]);
-		if (ret)
-			return ret;
-	}
-
-	return 0;
-}
-#endif
-
-#define MII_MMD_ACCESS_CTRL_REG		0xd
-#define MII_MMD_ACCESS_ADDR_DATA_REG	0xe
-#define MII_DBG_PORT_REG		0x1d
-#define MII_DBG_PORT2_REG		0x1e
-
-int fecmxc_mii_postcall(int phy)
-{
-	unsigned short val;
-
-	/*
-	 * Due to the i.MX6Q Armadillo2 board HW design,there is
-	 * no 125Mhz clock input from SOC. In order to use RGMII,
-	 * We need enable AR8031 ouput a 125MHz clk from CLK_25M
-	 */
-	miiphy_write("FEC", phy, MII_MMD_ACCESS_CTRL_REG, 0x7);
-	miiphy_write("FEC", phy, MII_MMD_ACCESS_ADDR_DATA_REG, 0x8016);
-	miiphy_write("FEC", phy, MII_MMD_ACCESS_CTRL_REG, 0x4007);
-	miiphy_read("FEC", phy, MII_MMD_ACCESS_ADDR_DATA_REG, &val);
-	val &= 0xffe3;
-	val |= 0x18;
-	miiphy_write("FEC", phy, MII_MMD_ACCESS_ADDR_DATA_REG, val);
-
-	/* For the RGMII phy, we need enable tx clock delay */
-	miiphy_write("FEC", phy, MII_DBG_PORT_REG, 0x5);
-	miiphy_read("FEC", phy, MII_DBG_PORT2_REG, &val);
-	val |= 0x0100;
-	miiphy_write("FEC", phy, MII_DBG_PORT2_REG, val);
-
-	miiphy_write("FEC", phy, MII_BMCR, 0xa100);
-
-	return 0;
-}
-
-int board_eth_init(struct bd_info *bis)
-{
-	struct eth_device *dev;
-	int ret = cpu_eth_init(bis);
-
-	if (ret)
-		return ret;
-
-	dev = eth_get_dev_by_name("FEC");
-	if (!dev) {
-		printf("FEC MXC: Unable to get FEC device entry\n");
-		return -EINVAL;
-	}
-
-	ret = fecmxc_register_mii_postcall(dev, fecmxc_mii_postcall);
-	if (ret) {
-		printf("FEC MXC: Unable to register FEC mii postcall\n");
-		return ret;
-	}
-
-	return 0;
-}
-
-#ifdef CONFIG_USB_EHCI_MX6
-#define USB_OTHERREGS_OFFSET	0x800
-#define UCTRL_PWR_POL		(1 << 9)
-
-static iomux_v3_cfg_t const usb_otg_pads[] = {
-	MX6_PAD_EIM_D22__USB_OTG_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
-	MX6_PAD_GPIO_1__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-static void setup_usb(void)
-{
-	imx_iomux_v3_setup_multiple_pads(usb_otg_pads,
-					 ARRAY_SIZE(usb_otg_pads));
-
-	/*
-	 * set daisy chain for otg_pin_id on 6q.
-	 * for 6dl, this bit is reserved
-	 */
-	imx_iomux_set_gpr_register(1, 13, 1, 1);
-}
-
-int board_ehci_hcd_init(int port)
-{
-	u32 *usbnc_usb_ctrl;
-
-	if (port > 0)
-		return -EINVAL;
-
-	usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET +
-				 port * 4);
-
-	setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL);
-
-	return 0;
-}
-#endif
-
-int board_early_init_f(void)
-{
-	setup_iomux_uart();
-	setup_iomux_enet();
-
-	return 0;
-}
-
-int board_init(void)
-{
-	/* address of boot parameters */
-	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
-
-#ifdef CONFIG_USB_EHCI_MX6
-	setup_usb();
-#endif
-
-	return 0;
-}
-
-int checkboard(void)
-{
-#ifdef CONFIG_MX6DL
-	puts("Board: MX6DL-Armadillo2\n");
-#else
-	puts("Board: MX6Q-Armadillo2\n");
-#endif
-
-	return 0;
-}
diff --git a/configs/mx6dlarm2_defconfig b/configs/mx6dlarm2_defconfig
deleted file mode 100644
index 57da844e8d3b..000000000000
--- a/configs/mx6dlarm2_defconfig
+++ /dev/null
@@ -1,41 +0,0 @@ 
-CONFIG_ARM=y
-CONFIG_ARCH_MX6=y
-CONFIG_SYS_TEXT_BASE=0x17800000
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x60000
-CONFIG_MX6DL=y
-CONFIG_TARGET_MX6QARM2=y
-# CONFIG_CMD_BMODE is not set
-CONFIG_SUPPORT_RAW_INITRD=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6qarm2/imximage_mx6dl.cfg,DDR_MB=2048"
-CONFIG_BOOTDELAY=3
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_BOOTZ=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_SYS_MMC_ENV_DEV=1
-CONFIG_BOUNCE_BUFFER=y
-CONFIG_FSL_USDHC=y
-CONFIG_MII=y
-CONFIG_MXC_UART=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_HOST_ETHER=y
-CONFIG_USB_ETHER_ASIX=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/mx6dlarm2_lpddr2_defconfig b/configs/mx6dlarm2_lpddr2_defconfig
deleted file mode 100644
index c1f4fed2cbeb..000000000000
--- a/configs/mx6dlarm2_lpddr2_defconfig
+++ /dev/null
@@ -1,41 +0,0 @@ 
-CONFIG_ARM=y
-CONFIG_ARCH_MX6=y
-CONFIG_SYS_TEXT_BASE=0x17800000
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x60000
-CONFIG_MX6DL=y
-CONFIG_TARGET_MX6QARM2=y
-# CONFIG_CMD_BMODE is not set
-CONFIG_SUPPORT_RAW_INITRD=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6qarm2/imximage_mx6dl.cfg,MX6DL_LPDDR2,DDR_MB=512"
-CONFIG_BOOTDELAY=3
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_BOOTZ=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_SYS_MMC_ENV_DEV=1
-CONFIG_BOUNCE_BUFFER=y
-CONFIG_FSL_USDHC=y
-CONFIG_MII=y
-CONFIG_MXC_UART=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_HOST_ETHER=y
-CONFIG_USB_ETHER_ASIX=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/mx6qarm2_defconfig b/configs/mx6qarm2_defconfig
deleted file mode 100644
index 180d5f9baa69..000000000000
--- a/configs/mx6qarm2_defconfig
+++ /dev/null
@@ -1,41 +0,0 @@ 
-CONFIG_ARM=y
-CONFIG_ARCH_MX6=y
-CONFIG_SYS_TEXT_BASE=0x17800000
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x60000
-CONFIG_MX6Q=y
-CONFIG_TARGET_MX6QARM2=y
-# CONFIG_CMD_BMODE is not set
-CONFIG_SUPPORT_RAW_INITRD=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6qarm2/imximage.cfg,DDR_MB=2048"
-CONFIG_BOOTDELAY=3
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_BOOTZ=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_SYS_MMC_ENV_DEV=1
-CONFIG_BOUNCE_BUFFER=y
-CONFIG_FSL_USDHC=y
-CONFIG_MII=y
-CONFIG_MXC_UART=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_HOST_ETHER=y
-CONFIG_USB_ETHER_ASIX=y
-CONFIG_OF_LIBFDT=y
diff --git a/configs/mx6qarm2_lpddr2_defconfig b/configs/mx6qarm2_lpddr2_defconfig
deleted file mode 100644
index d481f686be02..000000000000
--- a/configs/mx6qarm2_lpddr2_defconfig
+++ /dev/null
@@ -1,41 +0,0 @@ 
-CONFIG_ARM=y
-CONFIG_ARCH_MX6=y
-CONFIG_SYS_TEXT_BASE=0x17800000
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_ENV_SIZE=0x2000
-CONFIG_ENV_OFFSET=0x60000
-CONFIG_MX6Q=y
-CONFIG_TARGET_MX6QARM2=y
-# CONFIG_CMD_BMODE is not set
-CONFIG_SUPPORT_RAW_INITRD=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6qarm2/imximage.cfg,MX6DQ_LPDDR2,DDR_MB=512"
-CONFIG_BOOTDELAY=3
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_BOOTZ=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_SYS_MMC_ENV_DEV=1
-CONFIG_BOUNCE_BUFFER=y
-CONFIG_FSL_USDHC=y
-CONFIG_MII=y
-CONFIG_MXC_UART=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_HOST_ETHER=y
-CONFIG_USB_ETHER_ASIX=y
-CONFIG_OF_LIBFDT=y
diff --git a/include/configs/mx6qarm2.h b/include/configs/mx6qarm2.h
deleted file mode 100644
index 83c09ead2710..000000000000
--- a/include/configs/mx6qarm2.h
+++ /dev/null
@@ -1,127 +0,0 @@ 
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
- *
- * Configuration settings for the Freescale i.MX6Q Armadillo2 board.
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include "mx6_common.h"
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 2 * 1024 * 1024)
-
-#define CONFIG_MXC_UART_BASE		UART4_BASE
-
-/* MMC Configs */
-#define CONFIG_SYS_FSL_ESDHC_ADDR	USDHC4_BASE_ADDR
-#define CONFIG_SYS_FSL_USDHC_NUM	2
-
-#define	CONFIG_FEC_MXC
-#define IMX_FEC_BASE			ENET_BASE_ADDR
-#define	CONFIG_FEC_XCV_TYPE		RGMII
-#define CONFIG_FEC_MXC_PHYADDR		0
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	"script=boot.scr\0" \
-	"image=zImage\0" \
-	"console=ttymxc3\0" \
-	"fdt_file=imx6q-arm2.dtb\0" \
-	"fdt_addr=0x18000000\0" \
-	"fdt_high=0xffffffff\0" \
-	"initrd_high=0xffffffff\0" \
-	"boot_fdt=try\0" \
-	"ip_dyn=yes\0" \
-	"mmcdev=1\0" \
-	"mmcpart=1\0" \
-	"mmcroot=/dev/mmcblk0p2 rootwait rw\0" \
-	"mmcargs=setenv bootargs console=${console},${baudrate} " \
-		"root=${mmcroot}\0" \
-	"loadbootscript=" \
-		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
-	"bootscript=echo Running bootscript from mmc ...; " \
-		"source\0" \
-	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
-	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
-	"mmcboot=echo Booting from mmc ...; " \
-		"run mmcargs; " \
-		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
-			"if run loadfdt; then " \
-				"bootz ${loadaddr} - ${fdt_addr}; " \
-			"else " \
-				"if test ${boot_fdt} = try; then " \
-					"bootz; " \
-				"else " \
-					"echo WARN: Cannot load the DT; " \
-				"fi; " \
-			"fi; " \
-		"else " \
-			"bootz; " \
-		"fi;\0" \
-	"netargs=setenv bootargs console=${console},${baudrate} " \
-		"root=/dev/nfs " \
-		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
-	"netboot=echo Booting from net ...; " \
-		"run netargs; " \
-		"if test ${ip_dyn} = yes; then " \
-			"setenv get_cmd dhcp; " \
-		"else " \
-			"setenv get_cmd tftp; " \
-		"fi; " \
-		"${get_cmd} ${image}; " \
-		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
-			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
-				"bootz ${loadaddr} - ${fdt_addr}; " \
-			"else " \
-				"if test ${boot_fdt} = try; then " \
-					"bootz; " \
-				"else " \
-					"echo WARN: Cannot load the DT; " \
-				"fi; " \
-			"fi; " \
-		"else " \
-			"bootz; " \
-		"fi;\0"
-
-#define CONFIG_BOOTCOMMAND \
-	"mmc dev ${mmcdev};" \
-	"mmc dev ${mmcdev}; if mmc rescan; then " \
-		"if run loadbootscript; then " \
-			"run bootscript; " \
-		"else " \
-			"if run loadimage; then " \
-				"run mmcboot; " \
-			"else run netboot; " \
-			"fi; " \
-		"fi; " \
-	"else run netboot; fi"
-
-#define CONFIG_ARP_TIMEOUT	200UL
-
-/* Miscellaneous configurable options */
-
-/* Physical Memory Map */
-#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
-
-#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
-#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
-#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
-
-#define CONFIG_SYS_INIT_SP_OFFSET \
-	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR \
-	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
-
-/* Environment organization */
-
-/* USB Configs */
-#ifdef CONFIG_CMD_USB
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_MXC_USB_PORTSC		(PORT_PTS_UTMI | PORT_PTS_PTW)
-#define CONFIG_MXC_USB_FLAGS		0
-#define CONFIG_USB_MAX_CONTROLLER_COUNT	1
-#endif
-
-#endif				/* __CONFIG_H */