@@ -614,15 +614,6 @@ config TARGET_WANDBOARD
select BOARD_LATE_INIT
select SUPPORT_SPL
-config TARGET_XPRESS
- bool "CCV xPress"
- depends on MX6UL
- select BOARD_LATE_INIT
- select DM
- select DM_THERMAL
- select SUPPORT_SPL
- imply CMD_DM
-
config TARGET_ZC5202
bool "zc5202"
select BOARD_LATE_INIT
@@ -670,7 +661,6 @@ source "board/armadeus/opos6uldev/Kconfig"
source "board/barco/titanium/Kconfig"
source "board/boundary/nitrogen6x/Kconfig"
source "board/bticino/mamoj/Kconfig"
-source "board/ccv/xpress/Kconfig"
source "board/compulab/cm_fx6/Kconfig"
source "board/congatec/cgtqmx6eval/Kconfig"
source "board/dhelectronics/dh_imx6/Kconfig"
deleted file mode 100644
@@ -1,12 +0,0 @@
-if TARGET_XPRESS
-
-config SYS_BOARD
- default "xpress"
-
-config SYS_VENDOR
- default "ccv"
-
-config SYS_CONFIG_NAME
- default "xpress"
-
-endif
deleted file mode 100644
@@ -1,7 +0,0 @@
-CCV XPRESS BOARD
-M: Stefan Roese <sr@denx.de>
-S: Maintained
-F: board/ccv/xpress/
-F: include/configs/xpress.h
-F: configs/xpress_defconfig
-F: configs/xpress_spl_defconfig
deleted file mode 100644
@@ -1,6 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (C) 2015-2016 Stefan Roese <sr@denx.de>
-
-obj-y := xpress.o
-obj-$(CONFIG_SPL_BUILD) += spl.o
deleted file mode 100644
@@ -1,175 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2015-2016 Stefan Roese <sr@denx.de>
- *
- * Refer doc/imx/mkimage/imximage.txt for more details about how-to configure
- * and create imximage boot image
- *
- * The syntax is taken as close as possible with the kwbimage
- */
-
-/* image version */
-
-IMAGE_VERSION 2
-
-/*
- * Boot Device : one of
- * sd, nand
- */
-BOOT_FROM sd
-
-/*
- * Device Configuration Data (DCD)
- *
- * Each entry must have the format:
- * Addr-type Address Value
- *
- * where:
- * Addr-type register length (1,2 or 4 bytes)
- * Address absolute address of the register
- * value value to be stored in the register
- */
-
-#define __ASSEMBLY__
-#include <config.h>
-
-/* Enable all clocks */
-DATA 4 0x020c4068 0xffffffff
-DATA 4 0x020c406c 0xffffffff
-DATA 4 0x020c4070 0xffffffff
-DATA 4 0x020c4074 0xffffffff
-DATA 4 0x020c4078 0xffffffff
-DATA 4 0x020c407c 0xffffffff
-DATA 4 0x020c4080 0xffffffff
-DATA 4 0x020c4084 0xffffffff
-
-/* ddr io type */
-DATA 4 0x020e04b4 0x000C0000 /* IOMUXC_SW_PAD_CTL_GRP_DDR_TYPE */
-DATA 4 0x020e04ac 0x00000000 /* IOMUXC_SW_PAD_CTL_GRP_DDRPKE */
-
-/* clock */
-DATA 4 0x020e027c 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDCLK0_P */
-
-/* control and address */
-DATA 4 0x020E0250 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_CAS */
-DATA 4 0x020E024C 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_RAS */
-DATA 4 0x020E0490 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_ADDDS */
-DATA 4 0x020E0288 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_RESET */
-DATA 4 0x020E0270 0x00000000 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDBA2 - DSE can be
- configured using Group Control Register:
- IOMUXC_SW_PAD_CTL_GRP_CTLDS */
-DATA 4 0x020E0260 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_ODT0 */
-DATA 4 0x020E0264 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_ODT1 */
-DATA 4 0x020E04A0 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_CTLDS */
-
-/* data strobes */
-DATA 4 0x020e0494 0x00020000 /* IOMUXC_SW_PAD_CTL_GRP_DDRMODE_CTL */
-DATA 4 0x020e0280 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS0_P */
-DATA 4 0x020e0284 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS1_P */
-
-/* data */
-DATA 4 0x020E04B0 0x00020000 /* IOMUXC_SW_PAD_CTL_GRP_DDRMODE */
-DATA 4 0x020E0498 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_B0DS */
-DATA 4 0x020E04A4 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_B1DS */
-DATA 4 0x020E0244 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM0 */
-DATA 4 0x020E0248 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM1 */
-
-/*
- * DDR Controller Registers
- *
- * Manufacturer: IM
- * Device Part Number: IME1G16D3EEBG-15EI
- * Clock Freq.: 400MHz
- * Density per CS in Gb: 1
- * Chip Selects used: 1
- * Number of Banks: 8
- * Row address: 13
- * Column address: 10
- * Data bus width 16
- */
-DATA 4 0x021b001c 0x00008000 /* MMDC0_MDSCR, set the Configuration request bit
- during MMDC set up */
-
-/*
- * Calibration setup
- */
-DATA 4 0x021b0800 0xA1390003 /* DDR_PHY_P0_MPZQHWCTRL, enable both one-time &
- periodic HW ZQ calibration. */
-
-/*
- * For target board, may need to run write leveling calibration to fine tune
- * these settings.
- */
-DATA 4 0x021b080c 0x00000000
-
-/* Read DQS Gating calibration */
-DATA 4 0x021b083c 0x4164015C /* MPDGCTRL0 PHY0 */
-
-/* Read calibration */
-DATA 4 0x021b0848 0x40404446 /* MPRDDLCTL PHY0 */
-
-/* Write calibration */
-DATA 4 0x021b0850 0x40405A52 /* MPWRDLCTL PHY0 */
-
-/*
- * read data bit delay: (3 is the reccommended default value, although out of
- * reset value is 0)
- */
-DATA 4 0x021b081c 0x33333333 /* DDR_PHY_P0_MPREDQBY0DL3 */
-DATA 4 0x021b0820 0x33333333 /* DDR_PHY_P0_MPREDQBY1DL3 */
-DATA 4 0x021b082c 0xF3333333
-DATA 4 0x021b0830 0xF3333333
-
-DATA 4 0x021b08c0 0x00921012
-
-/* Clock Fine Tuning */
-DATA 4 0x021B0858 0x00000F00 /* [MMDC_MPSDCTRL] MMDC PHY CK Control Register */
-
-/* Complete calibration by forced measurement: */
-DATA 4 0x021b08b8 0x00000800 /* DDR_PHY_P0_MPMUR0, frc_msr */
-/*
- * Calibration setup end
- */
-
-/* MMDC init: */
-DATA 4 0x021b0004 0x0002002D /* MMDC0_MDPDC */
-DATA 4 0x021b0008 0x1B333030 /* MMDC0_MDOTC */
-DATA 4 0x021b000c 0x3F4352F3 /* MMDC0_MDCFG0 */
-DATA 4 0x021b0010 0xB66D0B63 /* MMDC0_MDCFG1 */
-DATA 4 0x021b0014 0x01FF00DB /* MMDC0_MDCFG2 */
-
-/*
- * MDMISC: RALAT kept to the high level of 5.
- * MDMISC: consider reducing RALAT if your 528MHz board design allow that.
- * Lower RALAT benefits:
- * a. better operation at low frequency, for LPDDR2 freq < 100MHz, change RALAT
- * to 3
- * b. Small performence improvment
- */
-DATA 4 0x021b0018 0x00201740 /* MMDC0_MDMISC */
-
-DATA 4 0x021b001c 0x00008000 /* MMDC0_MDSCR, set the Configuration request bit
- during MMDC set up */
-
-DATA 4 0x021b002c 0x000026D2 /* MMDC0_MDRWD */
-DATA 4 0x021b0030 0x00431023 /* MMDC0_MDOR */
-DATA 4 0x021b0040 0x00000047 /* Chan0 CS0_END */
-DATA 4 0x021b0000 0x82180000 /* MMDC0_MDCTL */
-
-/* Mode register writes */
-DATA 4 0x021b001c 0x02008032 /* MMDC0_MDSCR, MR2 write, CS0 */
-DATA 4 0x021b001c 0x00008033 /* MMDC0_MDSCR, MR3 write, CS0 */
-DATA 4 0x021b001c 0x00048031 /* MMDC0_MDSCR, MR1 write, CS0 */
-DATA 4 0x021b001c 0x15208030 /* MMDC0_MDSCR, MR0 write, CS0 */
-DATA 4 0x021b001c 0x04008040 /* MMDC0_MDSCR, ZQ calibration command sent to
- device on CS0 */
-
-DATA 4 0x021b0020 0x00000800 /* MMDC0_MDREF */
-DATA 4 0x021b0818 0x00000227 /* DDR_PHY_P0_MPODTCTRL */
-DATA 4 0x021b0004 0x0002556D /* MMDC0_MDPDC now SDCTL power down enabled */
-DATA 4 0x021b0404 0x00011006 /* MMDC0_MAPSR ADOPT power down enabled, MMDC will
- enter automatically to self-refresh while the
- number of idle cycle reached. */
-DATA 4 0x021b001c 0x00000000 /* MMDC0_MDSCR, clear this register (especially
- the configuration bit as initialization is
- complete) */
deleted file mode 100644
@@ -1,118 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * SPL specific code for CCV xPress
- *
- * Copyright (C) 2015-2016 Stefan Roese <sr@denx.de>
- */
-
-#include <common.h>
-#include <init.h>
-#include <spl.h>
-#include <asm/io.h>
-#include <asm/arch/mx6-ddr.h>
-#include <asm/arch/crm_regs.h>
-
-/* Configuration for IM IME1G16D3EEBG-15EI, 64M x 16 -> 128MiB */
-
-static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = {
- .grp_addds = 0x00000030,
- .grp_ddrmode_ctl = 0x00020000,
- .grp_b0ds = 0x00000030,
- .grp_ctlds = 0x00000030,
- .grp_b1ds = 0x00000030,
- .grp_ddrpke = 0x00000000,
- .grp_ddrmode = 0x00020000,
- .grp_ddr_type = 0x000c0000,
-};
-
-static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
- .dram_dqm0 = 0x00000030,
- .dram_dqm1 = 0x00000030,
- .dram_ras = 0x00000030,
- .dram_cas = 0x00000030,
- .dram_odt0 = 0x00000030,
- .dram_odt1 = 0x00000030,
- .dram_sdba2 = 0x00000000,
- .dram_sdclk_0 = 0x00000008,
- .dram_sdqs0 = 0x00000038,
- .dram_sdqs1 = 0x00000030,
- .dram_reset = 0x00000030,
-};
-
-static struct mx6_mmdc_calibration mx6_mmcd_calib = {
- .p0_mpwldectrl0 = 0x00000000,
- .p0_mpdgctrl0 = 0x4164015C,
- .p0_mprddlctl = 0x40404446,
- .p0_mpwrdlctl = 0x40405A52,
-};
-
-struct mx6_ddr_sysinfo ddr_sysinfo = {
- .dsize = 0,
- .cs_density = 20,
- .ncs = 1,
- .cs1_mirror = 0,
- .rtt_wr = 2,
- .rtt_nom = 1, /* RTT_Nom = RZQ/2 */
- .walat = 1, /* Write additional latency */
- .ralat = 5, /* Read additional latency */
- .mif3_mode = 3, /* Command prediction working mode */
- .bi_on = 1, /* Bank interleaving enabled */
- .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
- .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
- .ddr_type = DDR_TYPE_DDR3,
- .refsel = 1, /* Refresh cycles at 32KHz */
- .refr = 7, /* 8 refresh commands per refresh cycle */
-};
-
-static struct mx6_ddr3_cfg mem_ddr = {
- .mem_speed = 800,
- .density = 4,
- .width = 16,
- .banks = 8,
- .rowaddr = 13,
- .coladdr = 10,
- .pagesz = 2,
- .trcd = 1375,
- .trcmin = 4875,
- .trasmin = 3500,
-};
-
-static void ccgr_init(void)
-{
- struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
-
- writel(0xFFFFFFFF, &ccm->CCGR0);
- writel(0xFFFFFFFF, &ccm->CCGR1);
- writel(0xFFFFFFFF, &ccm->CCGR2);
- writel(0xFFFFFFFF, &ccm->CCGR3);
- writel(0xFFFFFFFF, &ccm->CCGR4);
- writel(0xFFFFFFFF, &ccm->CCGR5);
- writel(0xFFFFFFFF, &ccm->CCGR6);
- writel(0xFFFFFFFF, &ccm->CCGR7);
-}
-
-static void spl_dram_init(void)
-{
- mx6ul_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs);
- mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr);
-}
-
-void board_init_f(ulong dummy)
-{
- /* Setup AIPS and disable watchdog */
- arch_cpu_init();
-
- ccgr_init();
-
- /* Setup iomux and i2c */
- board_early_init_f();
-
- /* Setup GP timer */
- timer_init();
-
- /* UART clocks enabled and gd valid - init serial console */
- preloader_console_init();
-
- /* DDR initialization */
- spl_dram_init();
-}
deleted file mode 100644
@@ -1,341 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2015-2016 Stefan Roese <sr@denx.de>
- */
-
-#include <init.h>
-#include <net.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/iomux.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/crm_regs.h>
-#include <asm/arch/mx6ul_pins.h>
-#include <asm/arch/mx6-pins.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/global_data.h>
-#include <asm/gpio.h>
-#include <asm/mach-imx/iomux-v3.h>
-#include <asm/mach-imx/boot_mode.h>
-#include <asm/mach-imx/mxc_i2c.h>
-#include <asm/io.h>
-#include <common.h>
-#include <env.h>
-#include <fsl_esdhc_imx.h>
-#include <i2c.h>
-#include <miiphy.h>
-#include <mmc.h>
-#include <netdev.h>
-#include <usb.h>
-#include <linux/delay.h>
-#include <usb/ehci-ci.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
- PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
- PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-
-#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
- PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \
- PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-
-#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
- PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
- PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
- PAD_CTL_ODE)
-
-#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
- PAD_CTL_SPEED_HIGH | \
- PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST)
-
-#define MDIO_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
- PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST | PAD_CTL_ODE)
-
-#define ENET_CLK_PAD_CTRL (PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
-
-#define ENET_RX_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
- PAD_CTL_SPEED_HIGH | PAD_CTL_SRE_FAST)
-
-#define OTGID_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
- PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \
- PAD_CTL_DSE_80ohm | PAD_CTL_HYS | \
- PAD_CTL_SRE_FAST)
-
-#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
-
-static struct i2c_pads_info i2c_pad_info1 = {
- .scl = {
- .i2c_mode = MX6_PAD_GPIO1_IO02__I2C1_SCL | PC,
- .gpio_mode = MX6_PAD_GPIO1_IO02__GPIO1_IO02 | PC,
- .gp = IMX_GPIO_NR(1, 2),
- },
- .sda = {
- .i2c_mode = MX6_PAD_GPIO1_IO03__I2C1_SDA | PC,
- .gpio_mode = MX6_PAD_GPIO1_IO03__GPIO1_IO03 | PC,
- .gp = IMX_GPIO_NR(1, 3),
- },
-};
-
-static struct i2c_pads_info i2c_pad_info2 = {
- .scl = {
- .i2c_mode = MX6_PAD_GPIO1_IO00__I2C2_SCL | PC,
- .gpio_mode = MX6_PAD_GPIO1_IO00__GPIO1_IO00 | PC,
- .gp = IMX_GPIO_NR(1, 0),
- },
- .sda = {
- .i2c_mode = MX6_PAD_GPIO1_IO01__I2C2_SDA | PC,
- .gpio_mode = MX6_PAD_GPIO1_IO01__GPIO1_IO01 | PC,
- .gp = IMX_GPIO_NR(1, 1),
- },
-};
-
-static struct i2c_pads_info i2c_pad_info4 = {
- .scl = {
- .i2c_mode = MX6_PAD_UART2_TX_DATA__I2C4_SCL | PC,
- .gpio_mode = MX6_PAD_UART2_TX_DATA__GPIO1_IO20 | PC,
- .gp = IMX_GPIO_NR(1, 20),
- },
- .sda = {
- .i2c_mode = MX6_PAD_UART2_RX_DATA__I2C4_SDA | PC,
- .gpio_mode = MX6_PAD_UART2_RX_DATA__GPIO1_IO21 | PC,
- .gp = IMX_GPIO_NR(1, 21),
- },
-};
-
-int dram_init(void)
-{
- gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
-
- return 0;
-}
-
-static iomux_v3_cfg_t const uart1_pads[] = {
- MX6_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_UART1_CTS_B__UART1_DCE_CTS | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_UART1_RTS_B__UART1_DCE_RTS | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const uart4_pads[] = {
- MX6_PAD_UART4_TX_DATA__UART4_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_UART4_RX_DATA__UART4_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const uart5_pads[] = {
- MX6_PAD_GPIO1_IO04__UART5_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_GPIO1_IO05__UART5_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_GPIO1_IO09__UART5_DCE_CTS | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_GPIO1_IO08__UART5_DCE_RTS | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const uart7_pads[] = {
- MX6_PAD_ENET2_RX_EN__UART7_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_ENET2_TX_DATA0__UART7_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const uart8_pads[] = {
- MX6_PAD_LCD_DATA20__UART8_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_LCD_DATA21__UART8_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-static void setup_iomux_uart(void)
-{
- imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
- imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
- imx_iomux_v3_setup_multiple_pads(uart5_pads, ARRAY_SIZE(uart5_pads));
- imx_iomux_v3_setup_multiple_pads(uart7_pads, ARRAY_SIZE(uart7_pads));
- imx_iomux_v3_setup_multiple_pads(uart8_pads, ARRAY_SIZE(uart8_pads));
-}
-
-/* eMMC on USDHC2 */
-static iomux_v3_cfg_t const usdhc2_pads[] = {
- MX6_PAD_NAND_RE_B__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NAND_WE_B__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NAND_DATA00__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NAND_DATA01__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NAND_DATA02__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NAND_DATA04__USDHC2_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NAND_DATA05__USDHC2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NAND_DATA06__USDHC2_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NAND_DATA07__USDHC2_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-
- /*
- * RST_B
- */
- MX6_PAD_NAND_ALE__USDHC2_RESET_B | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-static struct fsl_esdhc_cfg usdhc_cfg = {
- .esdhc_base = USDHC2_BASE_ADDR,
- .max_bus_width = 8,
-};
-
-#define USDHC2_PWR_GPIO IMX_GPIO_NR(1, 9)
-
-int board_mmc_getcd(struct mmc *mmc)
-{
- /* eMMC is always present */
- return 1;
-}
-
-int board_mmc_init(struct bd_info *bis)
-{
- imx_iomux_v3_setup_multiple_pads(usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
-
- usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
-
- return fsl_esdhc_initialize(bis, &usdhc_cfg);
-}
-
-#define USB_OTHERREGS_OFFSET 0x800
-#define UCTRL_PWR_POL (1 << 9)
-
-static iomux_v3_cfg_t const usb_otg_pads[] = {
- /* OTG1 */
- MX6_PAD_SD1_CMD__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_SD1_DATA0__ANATOP_OTG1_ID | MUX_PAD_CTRL(OTGID_PAD_CTRL),
- /* OTG2 */
- MX6_PAD_SD1_DATA1__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_SD1_DATA3__ANATOP_OTG2_ID | MUX_PAD_CTRL(OTGID_PAD_CTRL),
-};
-
-static void setup_usb(void)
-{
- imx_iomux_v3_setup_multiple_pads(usb_otg_pads,
- ARRAY_SIZE(usb_otg_pads));
-}
-
-int board_usb_phy_mode(int port)
-{
- if (port == 1)
- return USB_INIT_HOST;
- else
- return usb_phy_mode(port);
-}
-
-int board_ehci_hcd_init(int port)
-{
- u32 *usbnc_usb_ctrl;
-
- if (port > 1)
- return -EINVAL;
-
- usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET +
- port * 4);
-
- /* Set Power polarity */
- setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL);
-
- return 0;
-}
-
-static iomux_v3_cfg_t const fec1_pads[] = {
- MX6_PAD_GPIO1_IO06__ENET1_MDIO | MUX_PAD_CTRL(MDIO_PAD_CTRL),
- MX6_PAD_GPIO1_IO07__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET1_TX_DATA0__ENET1_TDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET1_TX_DATA1__ENET1_TDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET1_TX_EN__ENET1_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
- MX6_PAD_ENET1_RX_DATA0__ENET1_RDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET1_RX_DATA1__ENET1_RDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET1_RX_ER__ENET1_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET1_RX_EN__ENET1_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
-
- /* ENET1 reset */
- MX6_PAD_CSI_MCLK__GPIO4_IO17 | MUX_PAD_CTRL(NO_PAD_CTRL),
- /* ENET1 interrupt */
- MX6_PAD_CSI_PIXCLK__GPIO4_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-#define ENET_PHY_RESET_GPIO IMX_GPIO_NR(4, 17)
-
-int board_eth_init(struct bd_info *bis)
-{
- int ret;
-
- imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
-
- /* Reset LAN8742 PHY */
- ret = gpio_request(ENET_PHY_RESET_GPIO, "phy-reset");
- if (!ret)
- gpio_direction_output(ENET_PHY_RESET_GPIO , 0);
- mdelay(10);
- gpio_set_value(ENET_PHY_RESET_GPIO, 1);
- mdelay(10);
-
- return cpu_eth_init(bis);
-}
-
-static int setup_fec(int fec_id)
-{
- struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
- int ret;
-
- /*
- * Use 50M anatop loopback REF_CLK1 for ENET1,
- * clear gpr1[13], set gpr1[17].
- */
- clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC1_MASK,
- IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK);
-
- ret = enable_fec_anatop_clock(fec_id, ENET_50MHZ);
- if (ret)
- return ret;
-
- enable_enet_clk(1);
-
- return 0;
-}
-
-int board_phy_config(struct phy_device *phydev)
-{
- if (phydev->drv->config)
- phydev->drv->config(phydev);
-
- return 0;
-}
-
-int board_early_init_f(void)
-{
- setup_iomux_uart();
-
- return 0;
-}
-
-int board_init(void)
-{
- /* Address of boot parameters */
- gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
-
- setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
- setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
- setup_i2c(3, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info4);
-
- setup_fec(CONFIG_FEC_ENET_DEV);
-
- setup_usb();
-
- return 0;
-}
-
-static const struct boot_mode board_boot_modes[] = {
- /* 8 bit bus width */
- {"emmc", MAKE_CFGVAL(0x60, 0x28, 0x00, 0x00)},
- { NULL, 0 },
-};
-
-int board_late_init(void)
-{
- add_board_boot_modes(board_boot_modes);
- env_set("board_name", "xpress");
-
- return 0;
-}
-
-int checkboard(void)
-{
- puts("Board: CCV-EVA xPress\n");
-
- return 0;
-}
deleted file mode 100644
@@ -1,46 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_MX6=y
-CONFIG_SYS_TEXT_BASE=0x87800000
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_SYS_MEMTEST_START=0x80000000
-CONFIG_SYS_MEMTEST_END=0x90000000
-CONFIG_ENV_SIZE=0x4000
-CONFIG_ENV_OFFSET=0x80000
-CONFIG_MX6UL=y
-CONFIG_TARGET_XPRESS=y
-CONFIG_SUPPORT_RAW_INITRD=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/ccv/xpress/imximage.cfg"
-CONFIG_BOOTDELAY=3
-CONFIG_SYS_CONSOLE_INFO_QUIET=y
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_BOOTZ=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_SYS_MMC_ENV_PART=1
-CONFIG_BOUNCE_BUFFER=y
-CONFIG_SUPPORT_EMMC_BOOT=y
-CONFIG_FSL_USDHC=y
-CONFIG_MTD=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_SMSC=y
-CONFIG_MII=y
-CONFIG_MXC_UART=y
-CONFIG_IMX_THERMAL=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
deleted file mode 100644
@@ -1,57 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_MX6=y
-CONFIG_SYS_TEXT_BASE=0x87800000
-CONFIG_SPL_GPIO_SUPPORT=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_SYS_MEMTEST_START=0x80000000
-CONFIG_SYS_MEMTEST_END=0x90000000
-CONFIG_ENV_SIZE=0x4000
-CONFIG_ENV_OFFSET=0x80000
-CONFIG_MX6UL=y
-CONFIG_TARGET_XPRESS=y
-CONFIG_SPL_TEXT_BASE=0x00908000
-CONFIG_SPL_MMC_SUPPORT=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_SPL_LIBDISK_SUPPORT=y
-CONFIG_SUPPORT_RAW_INITRD=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
-CONFIG_BOOTDELAY=3
-CONFIG_SYS_CONSOLE_INFO_QUIET=y
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_SPL_FS_EXT4=y
-CONFIG_SPL_I2C_SUPPORT=y
-CONFIG_SPL_WATCHDOG_SUPPORT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_CMD_BOOTZ=y
-CONFIG_CMD_MEMTEST=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_SYS_MMC_ENV_PART=1
-CONFIG_BOUNCE_BUFFER=y
-CONFIG_SUPPORT_EMMC_BOOT=y
-CONFIG_FSL_USDHC=y
-CONFIG_MTD=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_SMSC=y
-CONFIG_MII=y
-CONFIG_MXC_UART=y
-CONFIG_IMX_THERMAL=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y
This board has not been converted to CONFIG_DM_MMC by the deadline. Remove it. Cc: Stefan Roese <sr@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com> --- arch/arm/mach-imx/mx6/Kconfig | 10 - board/ccv/xpress/Kconfig | 12 -- board/ccv/xpress/MAINTAINERS | 7 - board/ccv/xpress/Makefile | 6 - board/ccv/xpress/imximage.cfg | 175 ----------------- board/ccv/xpress/spl.c | 118 ------------ board/ccv/xpress/xpress.c | 341 ---------------------------------- configs/xpress_defconfig | 46 ----- configs/xpress_spl_defconfig | 57 ------ 9 files changed, 772 deletions(-) delete mode 100644 board/ccv/xpress/Kconfig delete mode 100644 board/ccv/xpress/MAINTAINERS delete mode 100644 board/ccv/xpress/Makefile delete mode 100644 board/ccv/xpress/imximage.cfg delete mode 100644 board/ccv/xpress/spl.c delete mode 100644 board/ccv/xpress/xpress.c delete mode 100644 configs/xpress_defconfig delete mode 100644 configs/xpress_spl_defconfig