new file mode 100644
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * NXP LS1028A-QDS device tree fragment for RCW 1xxx
+ *
+ * Copyright 2019-2021 NXP Semiconductors
+ */
+
+/*
+ * This setup is using a SCH-30842 card with AQR112 PHY in slot 1 for ENETC
+ * port 0 USXGMII.
+ */
+&slot1 {
+ #include "fsl-sch-30842.dtsi"
+};
+
+&enetc0 {
+ status = "okay";
+ phy-mode = "usxgmii";
+ phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@02}>;
+};
new file mode 100644
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * NXP LS1028A-QDS device tree fragment for RCW 6xxx
+ *
+ * Copyright 2019-2021 NXP Semiconductors
+ */
+
+/*
+ * This setup is using SCH-30842 cards with AQR112 PHY.
+ */
+&slot1 {
+ #include "fsl-sch-30842.dtsi"
+};
+
+&enetc0 {
+ status = "okay";
+ phy-mode = "sgmii-2500";
+ phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@02}>;
+};
new file mode 100644
@@ -0,0 +1,49 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * NXP LS1028A-QDS device tree fragment for RCW 7777
+ *
+ * Copyright 2019-2021 NXP Semiconductors
+ */
+
+/*
+ * This setup is using a SCH-30841 card with AQR412 10G quad PHY.
+ *
+ * Switch ports are mapped 1:1 to AQR412 card ports seated in slot 1.
+ * Bottom port is port 0.
+ * Note that this is only usable for:
+ * - QDS boards WITHOUT lane B rework,
+ * - AQR412 card WITHOUT lane A -> lane C rework
+ *
+ * The following DTS assumes DIP SW5[1-3] = 000b.
+ */
+&slot1 {
+#include "fsl-sch-30841.dtsi"
+};
+
+&mscc_felix {
+ status = "okay";
+};
+
+&mscc_felix_port0 {
+ status = "okay";
+ phy-mode = "sgmii-2500";
+ phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@00}>;
+};
+
+&mscc_felix_port1 {
+ status = "okay";
+ phy-mode = "sgmii-2500";
+ phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@01}>;
+};
+
+&mscc_felix_port2 {
+ status = "okay";
+ phy-mode = "sgmii-2500";
+ phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@02}>;
+};
+
+&mscc_felix_port3 {
+ status = "okay";
+ phy-mode = "sgmii-2500";
+ phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@03}>;
+};
new file mode 100644
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * NXP LS1028A-QDS device tree fragment for RCW 7xx7
+ *
+ * Copyright 2019-2021 NXP Semiconductors
+ */
+
+&slot1 {
+#include "fsl-sch-30841.dtsi"
+};
+
+&mscc_felix {
+ status = "okay";
+};
+
+&mscc_felix_port0 {
+ status = "okay";
+ phy-mode = "sgmii-2500";
+ phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@02}>;
+};
+
+&mscc_felix_port3 {
+ status = "okay";
+ phy-mode = "sgmii-2500";
+ phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@03}>;
+};
new file mode 100644
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * NXP LS1028A-QDS device tree fragment for RCW 8xxx
+ *
+ * Copyright 2019-2021 NXP Semiconductors
+ */
+
+/*
+ * This setup is using SCH-24801 cards with VSC8234 quad SGMII PHY in slot 1.
+ */
+&slot1 {
+ #include "fsl-sch-24801.dtsi"
+};
+
+&enetc0 {
+ status = "okay";
+ phy-mode = "sgmii";
+ phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1c}>;
+};
new file mode 100644
@@ -0,0 +1,63 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * NXP LS1028A-QDS device tree fragment for RCW 9999
+ *
+ * Copyright 2019-2021 NXP Semiconductors
+ */
+
+/*
+ * This setup is using SCH-24801 cards with VSC8234 quad SGMII PHY.
+ * LS1028A QDS boards with lane B rework require two cards for the 4 switch
+ * ports, QDS boards without the lane B rework only require one card.
+ *
+ * Switch ports are routed as follows:
+ * Port 0 goes to 1st port of VSC8234 quad card in slot 1,
+ * Port 1:
+ * - if the QDS has had lane B rework, it is 1st port in slot 2,
+ * - otherwise it is 2nd port in slot 1.
+ * Port 2:
+ * - if DIP SW5[1] = 0 it is 3rd port in slot 1,
+ * - otherwise it is 1st port in slot 3.
+ * Port 3:
+ * - if DIP SW5[2-3] = 00b it is 4th port in slot 1,
+ * - if DIP SW5[2-3] = 01b it is 2nd port in slot 3,
+ * - if DIP SW5[2-3] = 11b it is 1st port in slot 4.
+ *
+ * The following DTS assumes QDS lane B rework and DIP SW5[1-3] = 000b. Two
+ * SCH-24801 cards are required in slots 1 and 2.
+ */
+&slot1 {
+ #include "fsl-sch-24801.dtsi"
+};
+
+&slot2 {
+ #include "fsl-sch-24801.dtsi"
+};
+
+&mscc_felix {
+ status = "okay";
+};
+
+&mscc_felix_port0 {
+ status = "okay";
+ phy-mode = "sgmii";
+ phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1c}>;
+};
+
+&mscc_felix_port1 {
+ status = "okay";
+ phy-mode = "sgmii";
+ phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@1c}>;
+};
+
+&mscc_felix_port2 {
+ status = "okay";
+ phy-mode = "sgmii";
+ phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1e}>;
+};
+
+&mscc_felix_port3 {
+ status = "okay";
+ phy-mode = "sgmii";
+ phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1f}>;
+};
new file mode 100644
@@ -0,0 +1,48 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * NXP LS1028A-QDS device tree fragment for RCW 9999
+ *
+ * Copyright 2019-2021 NXP Semiconductors
+ *
+ */
+
+/*
+ * This set-up is using SCH-24801 cards with VSC8234 quad SGMII PHY.
+ *
+ * Switch ports are mapped 1:1 to VSC8234 card ports seated in slot 1.
+ * Top port is port 0.
+ *
+ * The following DTS assumes DIP SW5[1-3] = 000b.
+ */
+
+&slot1 {
+ #include "fsl-sch-24801.dtsi"
+};
+
+&mscc_felix {
+ status = "okay";
+};
+
+&mscc_felix_port0 {
+ status = "okay";
+ phy-mode = "sgmii";
+ phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1c}>;
+};
+
+&mscc_felix_port1 {
+ status = "okay";
+ phy-mode = "sgmii";
+ phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1d}>;
+};
+
+&mscc_felix_port2 {
+ status = "okay";
+ phy-mode = "sgmii";
+ phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1e}>;
+};
+
+&mscc_felix_port3 {
+ status = "okay";
+ phy-mode = "sgmii";
+ phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@40/phy@1f}>;
+};
new file mode 100644
@@ -0,0 +1,48 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * NXP LS1028A-QDS device tree fragment for RCW x3xx
+ *
+ * Copyright 2019-2021 NXP Semiconductors
+ */
+
+/*
+ * This setup is using a SCH-30841-R card with AQR412 quad PHY in slot 2. This
+ * is used for the 4 integrated ethernet switch in a multiplexes USXGMII set-up.
+ *
+ * We're including the normal .dsti file, not the reworked card .dtsi
+ * intentionally. We are using multiplexing of the 4 interfaces on a single
+ * lane and the rework doesn't actually disable any port. The rework is in fact
+ * needed, otherwise the PHY won't work with the default wiring on the QDS/PHY
+ * card.
+ */
+&slot2 {
+#include "fsl-sch-30841.dtsi"
+};
+
+&mscc_felix {
+ status = "okay";
+};
+
+&mscc_felix_port0 {
+ status = "okay";
+ phy-mode = "usxgmii";
+ phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@00}>;
+};
+
+&mscc_felix_port1 {
+ status = "okay";
+ phy-mode = "usxgmii";
+ phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@01}>;
+};
+
+&mscc_felix_port2 {
+ status = "okay";
+ phy-mode = "usxgmii";
+ phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@02}>;
+};
+
+&mscc_felix_port3 {
+ status = "okay";
+ phy-mode = "usxgmii";
+ phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@03}>;
+};
new file mode 100644
@@ -0,0 +1,42 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * NXP LS1028A-QDS device tree fragment for RCW x5xx
+ *
+ * Copyright 2019-2021 NXP Semiconductors
+ */
+
+/*
+ * This setup is using SCH-28021 cards with VSC8514 QSGMII PHY in slot 2.
+ * This is only available on LS1028A QDS boards with lane B rework.
+ */
+&slot2 {
+ #include "fsl-sch-28021.dtsi"
+};
+
+&mscc_felix {
+ status = "okay";
+};
+
+&mscc_felix_port0 {
+ status = "okay";
+ phy-mode = "qsgmii";
+ phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@08}>;
+};
+
+&mscc_felix_port1 {
+ status = "okay";
+ phy-mode = "qsgmii";
+ phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@09}>;
+};
+
+&mscc_felix_port2 {
+ status = "okay";
+ phy-mode = "qsgmii";
+ phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@0a}>;
+};
+
+&mscc_felix_port3 {
+ status = "okay";
+ phy-mode = "qsgmii";
+ phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@0b}>;
+};
new file mode 100644
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * NXP LS1028A-QDS device tree fragment for RCW 7777
+ *
+ * Copyright 2019-2021 NXP Semiconductors
+ */
+
+&slot2 {
+#include "fsl-sch-30842.dtsi"
+};
+
+&mscc_felix {
+ status = "okay";
+};
+
+&mscc_felix_port1 {
+ status = "okay";
+ phy-mode = "sgmii-2500";
+ phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@50/phy@02}>;
+};
new file mode 100644
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * NXP LS1028A-QDS device tree fragment for RCW 7777
+ *
+ * Copyright 2019-2021 NXP Semiconductors
+ */
+
+&slot3 {
+#include "fsl-sch-30842.dtsi"
+};
+
+&mscc_felix {
+ status = "okay";
+};
+
+&mscc_felix_port2 {
+ status = "okay";
+ phy-mode = "sgmii-2500";
+ phy-handle = <&{/i2c@2000000/fpga@66/mux-mdio@54/mdio@60/phy@02}>;
+};
@@ -258,3 +258,6 @@
&mdio0 {
status = "okay";
};
+
+#include "fsl-ls1028a-qds-8xxx-sch-24801.dtsi"
+#include "fsl-ls1028a-qds-x5xx-sch-28021-LBRW.dtsi"
new file mode 100644
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * Device tree fragment for RCW SCH-24801 card
+ *
+ * Copyright 2019-2021 NXP Semiconductors
+ */
+
+/*
+ * SCH-24801 is a 4xSGMII add-on card used with various FSL QDS boards.
+ * It integrates a VSC8234 quad PHY which supports 4 SGMII interfaces.
+ * PHY addresses are 0x1c - 0x1f.
+ * On the card the first port is the top port (farthest from PEX connector).
+ */
+phy@1c {
+ reg = <0x1c>;
+};
+
+phy@1d {
+ reg = <0x1d>;
+};
+
+phy@1e {
+ reg = <0x1e>;
+};
+
+phy@1f {
+ reg = <0x1f>;
+};
new file mode 100644
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * Device tree fragment for RCW SCH-28021 card
+ *
+ * Copyright 2019-2021 NXP Semiconductors
+ */
+
+/*
+ * SCH-28021 is a QSGMII add-on card used with various FSL QDS boards.
+ * It integrates a VSC8514 quad PHY which supports 4 interfaces muxed on a
+ * single QSGMII lane.
+ * PHY addresses are 0x08 - 0x0b.
+ * On the card the first port is the top port (farthest from PEX connector).
+ */
+phy@08 {
+ reg = <0x08>;
+};
+
+phy@09 {
+ reg = <0x09>;
+};
+
+phy@0a {
+ reg = <0x0a>;
+};
+
+phy@0b {
+ reg = <0x0b>;
+};
new file mode 100644
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * Device tree fragment for RCW SCH-30841 card
+ *
+ * Copyright 2019-2021 NXP Semiconductors
+ */
+
+/*
+ * SCH-30841 is a 4 port add-on card used with various FSL QDS boards.
+ * It integrates a AQR412C quad PHY which supports 4 interfaces either muxed
+ * together on a single lane or mapped 1:1 to serdes lanes.
+ * It supports several protocols - SGMII, SGMII-2500, USXGMII, M-USX, XFI.
+ * PHY addresses are 0x00 - 0x03.
+ * On the card the first port is the bottom port (closest to PEX connector).
+ */
+phy@00 {
+ reg = <0x00>;
+ mdi-reversal = <1>;
+ smb-addr = <0x25>;
+};
+
+phy@01 {
+ reg = <0x01>;
+ mdi-reversal = <1>;
+ smb-addr = <0x26>;
+};
+
+phy@02 {
+ reg = <0x02>;
+ mdi-reversal = <1>;
+ smb-addr = <0x27>;
+};
+
+phy@03 {
+ reg = <0x03>;
+ mdi-reversal = <1>;
+ smb-addr = <0x28>;
+};
new file mode 100644
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * Device tree fragment for RCW SCH-30842 card
+ *
+ * Copyright 2019-2021 NXP Semiconductors
+ */
+
+/*
+ * SCH-30842 is a single port add-on card used with various FSL QDS boards.
+ * It integrates a AQR112 PHY, which supports several protocols - SGMII,
+ * SGMII-2500, USXGMII, XFI.
+ * PHY address is 0x02.
+ */
+phy@02 {
+ reg = <0x02>;
+ mdi-reversal = <1>;
+ smb-addr = <0x25>;
+};