@@ -70,7 +70,9 @@ struct fsl_esdhc {
uint sdtimingctl; /* SD timing control register */
char reserved8[20]; /* reserved */
uint dllcfg0; /* DLL config 0 register */
- char reserved9[680]; /* reserved */
+ char reserved9[12]; /* reserved */
+ uint dllstat0; /* DLL status 0 register */
+ char reserved10[664];/* reserved */
uint esdhcctl; /* eSDHC control register */
};
@@ -617,9 +619,11 @@ static void esdhc_exit_hs400(struct fsl_esdhc_priv *priv)
esdhc_tuning_block_enable(priv, false);
}
-static void esdhc_set_timing(struct fsl_esdhc_priv *priv, enum bus_mode mode)
+static int esdhc_set_timing(struct fsl_esdhc_priv *priv, enum bus_mode mode)
{
struct fsl_esdhc *regs = priv->esdhc_regs;
+ ulong start;
+ u32 val;
/* Exit HS400 mode before setting any other mode */
if (esdhc_read32(®s->tbctl) & HS400_MODE &&
@@ -640,17 +644,33 @@ static void esdhc_set_timing(struct fsl_esdhc_priv *priv, enum bus_mode mode)
esdhc_setbits32(®s->dllcfg0, DLL_FREQ_SEL);
esdhc_setbits32(®s->dllcfg0, DLL_ENABLE);
+
+ esdhc_setbits32(®s->dllcfg0, DLL_RESET);
+ udelay(1);
+ esdhc_clrbits32(®s->dllcfg0, DLL_RESET);
+
+ start = get_timer(0);
+ val = DLL_STS_SLV_LOCK;
+ while (!(esdhc_read32(®s->dllstat0) & val)) {
+ if (get_timer(start) > 1000) {
+ printf("fsl_esdhc: delay chain lock timeout\n");
+ return -ETIMEDOUT;
+ }
+ }
+
esdhc_setbits32(®s->tbctl, HS400_WNDW_ADJUST);
esdhc_clock_control(priv, false);
esdhc_flush_async_fifo(priv);
}
esdhc_clock_control(priv, true);
+ return 0;
}
static int esdhc_set_ios_common(struct fsl_esdhc_priv *priv, struct mmc *mmc)
{
struct fsl_esdhc *regs = priv->esdhc_regs;
+ int ret;
if (priv->is_sdhc_per_clk) {
/* Select to use peripheral clock */
@@ -667,7 +687,9 @@ static int esdhc_set_ios_common(struct fsl_esdhc_priv *priv, struct mmc *mmc)
set_sysctl(priv, mmc, mmc->clock);
/* Set timing */
- esdhc_set_timing(priv, mmc->selected_mode);
+ ret = esdhc_set_timing(priv, mmc->selected_mode);
+ if (ret)
+ return ret;
/* Set the bus width */
esdhc_clrbits32(®s->proctl, PROCTL_DTW_4 | PROCTL_DTW_8);
@@ -187,8 +187,12 @@
/* DLL config 0 register */
#define DLL_ENABLE 0x80000000
+#define DLL_RESET 0x40000000
#define DLL_FREQ_SEL 0x08000000
+/* DLL status 0 register */
+#define DLL_STS_SLV_LOCK 0x08000000
+
#define MAX_TUNING_LOOP 40
#define HOSTVER_VENDOR(x) (((x) >> 8) & 0xff)
For eMMC HS400 mode, the DLL reset is a required step for mmc rescan. This step has not been documented in reference manual, but the RM will be fixed sooner or later. In previous commit to support eMMC HS400, db8f936 mmc: fsl_esdhc: support eMMC HS400 mode the steps to configure DLL could be found in commit message, 13. Set DLLCFG0[DLL_ENABLE] and DLLCFG0[DLL_FREQ_SEL]. 14. Wait for delay chain to lock. these would be fixed as, 13. Set DLLCFG0[DLL_ENABLE] and DLLCFG0[DLL_FREQ_SEL]. 13.1 Write DLLCFG0[DLL_RESET] to 1 and wait for 1us, then write DLLCFG0[DLL_RESET] 14. Wait for delay chain to lock. This patch is to add the step of DLL reset, and make sure delay chain locked for HS400. Fixes: db8f93672b42 ("mmc: fsl_esdhc: support eMMC HS400 mode") Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> --- Changes for v2: - Added "Reviewed-by". - Explained more in commit message. --- drivers/mmc/fsl_esdhc.c | 28 +++++++++++++++++++++++++--- include/fsl_esdhc.h | 4 ++++ 2 files changed, 29 insertions(+), 3 deletions(-)