[1/2] pinctrl: stm32: Convert to use APIs which support live DT

Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
---

 drivers/pinctrl/pinctrl_stm32.c | 43 ++++++++++++++++++---------------
 1 file changed, 23 insertions(+), 20 deletions(-)

Hi Patrick

On 9/9/20 5:50 PM, Patrick Delaunay wrote:
> Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
> driver can support live DT.
>
> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
> ---
>
>  drivers/pinctrl/pinctrl_stm32.c | 43 ++++++++++++++++++---------------
>  1 file changed, 23 insertions(+), 20 deletions(-)
>
> diff --git a/drivers/pinctrl/pinctrl_stm32.c b/drivers/pinctrl/pinctrl_stm32.c
> index 71fa29a389..24ed83dd46 100644
> --- a/drivers/pinctrl/pinctrl_stm32.c
> +++ b/drivers/pinctrl/pinctrl_stm32.c
> @@ -13,8 +13,6 @@
>  #include <linux/err.h>
>  #include <linux/libfdt.h>
>  
> -DECLARE_GLOBAL_DATA_PTR;
> -
>  #define MAX_PINS_ONE_IP			70
>  #define MODE_BITS_MASK			3
>  #define OSPEED_MASK			3
> @@ -308,7 +306,8 @@ static int prep_gpio_dsc(struct stm32_gpio_dsc *gpio_dsc, u32 port_pin)
>  	return 0;
>  }
>  
> -static int prep_gpio_ctl(struct stm32_gpio_ctl *gpio_ctl, u32 gpio_fn, int node)
> +static int prep_gpio_ctl(struct stm32_gpio_ctl *gpio_ctl, u32 gpio_fn,
> +			 ofnode node)
>  {
>  	gpio_fn &= 0x00FF;
>  	gpio_ctl->af = 0;
> @@ -329,16 +328,16 @@ static int prep_gpio_ctl(struct stm32_gpio_ctl *gpio_ctl, u32 gpio_fn, int node)
>  		break;
>  	}
>  
> -	gpio_ctl->speed = fdtdec_get_int(gd->fdt_blob, node, "slew-rate", 0);
> +	gpio_ctl->speed = ofnode_read_u32_default(node, "slew-rate", 0);
>  
> -	if (fdtdec_get_bool(gd->fdt_blob, node, "drive-open-drain"))
> +	if (ofnode_read_bool(node, "drive-open-drain"))
>  		gpio_ctl->otype = STM32_GPIO_OTYPE_OD;
>  	else
>  		gpio_ctl->otype = STM32_GPIO_OTYPE_PP;
>  
> -	if (fdtdec_get_bool(gd->fdt_blob, node, "bias-pull-up"))
> +	if (ofnode_read_bool(node, "bias-pull-up"))
>  		gpio_ctl->pupd = STM32_GPIO_PUPD_UP;
> -	else if (fdtdec_get_bool(gd->fdt_blob, node, "bias-pull-down"))
> +	else if (ofnode_read_bool(node, "bias-pull-down"))
>  		gpio_ctl->pupd = STM32_GPIO_PUPD_DOWN;
>  	else
>  		gpio_ctl->pupd = STM32_GPIO_PUPD_NO;
> @@ -350,32 +349,37 @@ static int prep_gpio_ctl(struct stm32_gpio_ctl *gpio_ctl, u32 gpio_fn, int node)
>  	return 0;
>  }
>  
> -static int stm32_pinctrl_config(int offset)
> +static int stm32_pinctrl_config(ofnode node)
>  {
>  	u32 pin_mux[MAX_PINS_ONE_IP];
>  	int rv, len;
> +	ofnode subnode;
>  
>  	/*
>  	 * check for "pinmux" property in each subnode (e.g. pins1 and pins2 for
>  	 * usart1) of pin controller phandle "pinctrl-0"
>  	 * */
> -	fdt_for_each_subnode(offset, gd->fdt_blob, offset) {
> +	ofnode_for_each_subnode(subnode, node) {
>  		struct stm32_gpio_dsc gpio_dsc;
>  		struct stm32_gpio_ctl gpio_ctl;
>  		int i;
>  
> -		len = fdtdec_get_int_array_count(gd->fdt_blob, offset,
> -						 "pinmux", pin_mux,
> -						 ARRAY_SIZE(pin_mux));
> +		rv = ofnode_read_size(subnode, "pinmux");
> +		if (rv < 0)
> +			return rv;
> +		len = rv / sizeof(pin_mux[0]);
>  		debug("%s: no of pinmux entries= %d\n", __func__, len);
> -		if (len < 0)
> +		if (len > MAX_PINS_ONE_IP)
>  			return -EINVAL;
> +		rv = ofnode_read_u32_array(subnode, "pinmux", pin_mux, len);
> +		if (rv < 0)
> +			return rv;
>  		for (i = 0; i < len; i++) {
>  			struct gpio_desc desc;
>  
>  			debug("%s: pinmux = %x\n", __func__, *(pin_mux + i));
>  			prep_gpio_dsc(&gpio_dsc, *(pin_mux + i));
> -			prep_gpio_ctl(&gpio_ctl, *(pin_mux + i), offset);
> +			prep_gpio_ctl(&gpio_ctl, *(pin_mux + i), subnode);
>  			rv = uclass_get_device_by_seq(UCLASS_GPIO,
>  						      gpio_dsc.port,
>  						      &desc.dev);
> @@ -424,19 +428,18 @@ static int stm32_pinctrl_bind(struct udevice *dev)
>  #if CONFIG_IS_ENABLED(PINCTRL_FULL)
>  static int stm32_pinctrl_set_state(struct udevice *dev, struct udevice *config)
>  {
> -	return stm32_pinctrl_config(dev_of_offset(config));
> +	return stm32_pinctrl_config(dev_ofnode(config));
>  }
>  #else /* PINCTRL_FULL */
>  static int stm32_pinctrl_set_state_simple(struct udevice *dev,
>  					  struct udevice *periph)
>  {
> -	const void *fdt = gd->fdt_blob;
>  	const fdt32_t *list;
>  	uint32_t phandle;
> -	int config_node;
> +	ofnode config_node;
>  	int size, i, ret;
>  
> -	list = fdt_getprop(fdt, dev_of_offset(periph), "pinctrl-0", &size);
> +	list = ofnode_get_property(dev_ofnode(periph), "pinctrl-0", &size);
>  	if (!list)
>  		return -EINVAL;
>  
> @@ -446,8 +449,8 @@ static int stm32_pinctrl_set_state_simple(struct udevice *dev,
>  	for (i = 0; i < size; i++) {
>  		phandle = fdt32_to_cpu(*list++);
>  
> -		config_node = fdt_node_offset_by_phandle(fdt, phandle);
> -		if (config_node < 0) {
> +		config_node = ofnode_get_by_phandle(phandle);
> +		if (!ofnode_valid(config_node)) {
>  			pr_err("prop pinctrl-0 index %d invalid phandle\n", i);
>  			return -EINVAL;
>  		}

Reviewed-by: Patrice Chotard <patrice.chotard@st.com>

Thanks

Hi,

> From: Patrick DELAUNAY <patrick.delaunay@st.com>
> Sent: mercredi 9 septembre 2020 17:50
> 
> Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the driver can
> support live DT.
> 
> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
> ---
> 
>  drivers/pinctrl/pinctrl_stm32.c | 43 ++++++++++++++++++---------------
>  1 file changed, 23 insertions(+), 20 deletions(-)
> 

Applied to u-boot-stm/next, thanks!

Regards

Patrick