[v2,19/19] configs: j7200_evm_a72: Add Initial support

Add initial A72 defconfig support.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
---
 configs/j7200_evm_a72_defconfig | 175 ++++++++++++++++++++++++++++++++
 1 file changed, 175 insertions(+)
 create mode 100644 configs/j7200_evm_a72_defconfig

Hi Lokesh,

On 8/5/20 12:14 PM, Lokesh Vutla wrote:
> Add initial A72 defconfig support.
> 
> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
> ---
>  configs/j7200_evm_a72_defconfig | 175 ++++++++++++++++++++++++++++++++
>  1 file changed, 175 insertions(+)
>  create mode 100644 configs/j7200_evm_a72_defconfig
> 
> diff --git a/configs/j7200_evm_a72_defconfig b/configs/j7200_evm_a72_defconfig
> new file mode 100644
> index 0000000000..71f8d698c9
> --- /dev/null
> +++ b/configs/j7200_evm_a72_defconfig
> @@ -0,0 +1,175 @@
> +CONFIG_ARM=y
> +CONFIG_ARCH_K3=y
> +CONFIG_SPL_GPIO_SUPPORT=y
> +CONFIG_SPL_LIBCOMMON_SUPPORT=y
> +CONFIG_SPL_LIBGENERIC_SUPPORT=y
> +CONFIG_SYS_MALLOC_F_LEN=0x8000
> +CONFIG_SOC_K3_J721E=y
> +CONFIG_TARGET_J7200_A72_EVM=y
> +CONFIG_ENV_SIZE=0x20000
> +CONFIG_ENV_OFFSET=0x680000
> +CONFIG_SYS_SPI_U_BOOT_OFFS=0x280000
> +CONFIG_DM_GPIO=y
> +CONFIG_SPL_DM_SPI=y
> +CONFIG_SPL_TEXT_BASE=0x80080000
> +CONFIG_SPL_MMC_SUPPORT=y
> +CONFIG_SPL_SERIAL_SUPPORT=y
> +CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
> +CONFIG_SPL_STACK_R_ADDR=0x82000000
> +CONFIG_NR_DRAM_BANKS=2
> +CONFIG_ENV_OFFSET_REDUND=0x6A0000
> +CONFIG_SPL_FS_FAT=y
> +CONFIG_SPL_LIBDISK_SUPPORT=y
> +CONFIG_SPL_SPI_FLASH_SUPPORT=y
> +CONFIG_SPL_SPI_SUPPORT=y
> +# CONFIG_PSCI_RESET is not set
> +CONFIG_DEFAULT_DEVICE_TREE="k3-j7200-common-proc-board"
> +CONFIG_DISTRO_DEFAULTS=y
> +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> +CONFIG_SPL_LOAD_FIT=y
> +CONFIG_SPL_LOAD_FIT_ADDRESS=0x81000000
> +# CONFIG_USE_SPL_FIT_GENERATOR is not set
> +CONFIG_OF_BOARD_SETUP=y
> +CONFIG_BOOTCOMMAND="run findfdt; run envboot; run init_${boot}; run get_kern_${boot}; run get_fdt_${boot}; run get_overlay_${boot}; run run_kern"
> +CONFIG_SPL_BOARD_INIT=y
> +CONFIG_SPL_SYS_MALLOC_SIMPLE=y
> +CONFIG_SPL_STACK_R=y
> +CONFIG_SPL_SEPARATE_BSS=y
> +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
> +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x1400
> +CONFIG_SPL_DMA=y
> +CONFIG_SPL_ENV_SUPPORT=y
> +CONFIG_SPL_I2C_SUPPORT=y
> +CONFIG_SPL_DM_MAILBOX=y
> +CONFIG_SPL_DM_SPI_FLASH=y
> +CONFIG_SPL_DM_RESET=y
> +CONFIG_SPL_POWER_SUPPORT=y
> +CONFIG_SPL_POWER_DOMAIN=y
> +CONFIG_SPL_RAM_SUPPORT=y
> +CONFIG_SPL_RAM_DEVICE=y
> +# CONFIG_SPL_SPI_FLASH_TINY is not set
> +CONFIG_SPL_SPI_FLASH_SFDP_SUPPORT=y
> +CONFIG_SPL_SPI_LOAD=y
> +CONFIG_SPL_USB_GADGET=y
> +CONFIG_SPL_DFU=y
> +CONFIG_SPL_YMODEM_SUPPORT=y
> +CONFIG_CMD_ASKENV=y
> +CONFIG_CMD_DFU=y
> +# CONFIG_CMD_FLASH is not set
> +CONFIG_CMD_GPIO=y
> +CONFIG_CMD_GPT=y
> +CONFIG_CMD_I2C=y
> +CONFIG_CMD_MMC=y
> +CONFIG_CMD_MTD=y
> +CONFIG_CMD_REMOTEPROC=y
> +CONFIG_CMD_UFS=y
> +CONFIG_CMD_USB=y
> +CONFIG_CMD_USB_MASS_STORAGE=y
> +# CONFIG_CMD_SETEXPR is not set
> +CONFIG_CMD_TIME=y
> +CONFIG_CMD_EXT4_WRITE=y
> +CONFIG_MTDIDS_DEFAULT="nor0=47040000.spi.0,nor0=47034000.hyperbus"
> +CONFIG_MTDPARTS_DEFAULT="mtdparts=47040000.spi.0:512k(ospi.tiboot3),2m(ospi.tispl),4m(ospi.u-boot),128k(ospi.env),128k(ospi.env.backup),1m(ospi.sysfw),-@8m(ospi.rootfs);47034000.hyperbus:512k(hbmc.tiboot3),2m(hbmc.tispl),4m(hbmc.u-boot),256k(hbmc.env),1m(hbmc.sysfw),-@8m(hbmc.rootfs)"
> +CONFIG_CMD_UBI=y
> +# CONFIG_ISO_PARTITION is not set
> +# CONFIG_SPL_EFI_PARTITION is not set
> +CONFIG_OF_CONTROL=y
> +CONFIG_SPL_OF_CONTROL=y
> +CONFIG_SPL_MULTI_DTB_FIT=y
> +CONFIG_SPL_MULTI_DTB_FIT_NO_COMPRESSION=y
> +CONFIG_ENV_IS_IN_MMC=y

What about CONFIG_ENV_OVERWRITE?

Is env default -a -f supposed to work? I am getting a bunch of
## Error: Can't force access to <env variable>

> +CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
> +CONFIG_SYS_RELOC_GD_ENV_ADDR=y
> +CONFIG_NET_RANDOM_ETHADDR=y
> +CONFIG_DM=y
> +CONFIG_SPL_DM=y
> +CONFIG_SPL_DM_SEQ_ALIAS=y
> +CONFIG_REGMAP=y
> +CONFIG_SPL_REGMAP=y
> +CONFIG_SYSCON=y
> +CONFIG_SPL_OF_TRANSLATE=y
> +CONFIG_CLK=y
> +CONFIG_SPL_CLK=y
> +CONFIG_CLK_TI_SCI=y
> +CONFIG_DFU_MMC=y
> +CONFIG_DFU_RAM=y
> +CONFIG_DFU_SF=y
> +CONFIG_DMA_CHANNELS=y
> +CONFIG_TI_K3_NAVSS_UDMA=y
> +CONFIG_USB_FUNCTION_FASTBOOT=y
> +CONFIG_FASTBOOT_BUF_ADDR=0x82000000
> +CONFIG_FASTBOOT_BUF_SIZE=0x2F000000
> +CONFIG_FASTBOOT_FLASH=y
> +CONFIG_FASTBOOT_FLASH_MMC_DEV=0
> +CONFIG_FASTBOOT_CMD_OEM_FORMAT=y
> +CONFIG_TI_SCI_PROTOCOL=y
> +CONFIG_DA8XX_GPIO=y
> +CONFIG_DM_PCA953X=y
> +CONFIG_DM_I2C=y
> +CONFIG_SYS_I2C_OMAP24XX=y
> +CONFIG_DM_MAILBOX=y
> +CONFIG_K3_SEC_PROXY=y
> +CONFIG_DM_MMC=y
> +CONFIG_SUPPORT_EMMC_BOOT=y
> +CONFIG_MMC_SDHCI=y
> +CONFIG_MMC_SDHCI_ADMA=y
> +CONFIG_SPL_MMC_SDHCI_ADMA=y
> +CONFIG_MMC_SDHCI_AM654=y
> +CONFIG_MTD=y
> +CONFIG_DM_MTD=y
> +CONFIG_MTD_NOR_FLASH=y
> +CONFIG_FLASH_CFI_DRIVER=y
> +CONFIG_CFI_FLASH=y
> +CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
> +CONFIG_FLASH_CFI_MTD=y
> +CONFIG_SYS_FLASH_CFI=y
> +CONFIG_HBMC_AM654=y
> +CONFIG_DM_SPI_FLASH=y
> +CONFIG_SPI_FLASH_STMICRO=y
> +# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
> +CONFIG_SPI_FLASH_MTD=y
> +CONFIG_PHY_FIXED=y
> +CONFIG_DM_ETH=y
> +CONFIG_TI_AM65_CPSW_NUSS=y
> +CONFIG_PINCTRL=y
> +# CONFIG_PINCTRL_GENERIC is not set
> +CONFIG_SPL_PINCTRL=y
> +# CONFIG_SPL_PINCTRL_GENERIC is not set
> +CONFIG_PINCTRL_SINGLE=y
> +CONFIG_POWER_DOMAIN=y
> +CONFIG_TI_SCI_POWER_DOMAIN=y
> +CONFIG_RAM=y
> +CONFIG_SPL_RAM=y
> +CONFIG_REMOTEPROC_TI_K3_DSP=y

There are no DSPs on J7200, so this can be dropped.

> +CONFIG_REMOTEPROC_TI_K3_R5F=y

Please drop this and CMD_REMOTEPROC until the support for the same is actually added on J7200 SoCs.

The list of remoteprocs on J7200 is different from J721E, so we don't want the environment showing up any of these false remoteprocs from J721E.

> +CONFIG_DM_RESET=y
> +CONFIG_RESET_TI_SCI=y
> +CONFIG_SCSI=y
> +CONFIG_DM_SCSI=y
> +CONFIG_DM_SERIAL=y
> +CONFIG_SOC_DEVICE=y
> +CONFIG_SOC_DEVICE_TI_K3=y
> +CONFIG_SOC_TI=y
> +CONFIG_SPI=y
> +CONFIG_DM_SPI=y
> +CONFIG_CADENCE_QSPI=y
> +CONFIG_SYSRESET=y
> +CONFIG_SPL_SYSRESET=y
> +CONFIG_SYSRESET_TI_SCI=y
> +CONFIG_USB=y
> +CONFIG_DM_USB=y
> +CONFIG_DM_USB_GADGET=y
> +CONFIG_SPL_DM_USB_GADGET=y
> +CONFIG_USB_XHCI_HCD=y
> +CONFIG_USB_CDNS3=y
> +CONFIG_USB_CDNS3_GADGET=y
> +CONFIG_USB_CDNS3_HOST=y
> +CONFIG_SPL_USB_CDNS3_GADGET=y
> +CONFIG_USB_GADGET=y
> +CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments"
> +CONFIG_USB_GADGET_VENDOR_NUM=0x0451
> +CONFIG_USB_GADGET_PRODUCT_NUM=0x6164
> +CONFIG_UFS=y
> +CONFIG_CADENCE_UFS=y
> +CONFIG_TI_J721E_UFS=y
> +CONFIG_OF_LIBFDT_OVERLAY=y
> 

So, in general, this seems to be based on the current J721E defconfig which evolved over time as the corresponding drivers got enabled and supported. Do we want to enable all the related driver defconfigs without them being added/supported in the dts file.

regards
Suman