diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 2c86b293a8..9541ee614f 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -638,6 +638,7 @@ dtb-$(CONFIG_ARCH_MX7ULP) += imx7ulp-evk.dtb
 dtb-$(CONFIG_ARCH_IMX8) += \
 	fsl-imx8qm-apalis.dtb \
 	fsl-imx8qm-mek.dtb \
+	imx8qm-cgtqmx8.dtb \
 	fsl-imx8qxp-colibri.dtb \
 	fsl-imx8qxp-mek.dtb
 
diff --git a/arch/arm/dts/imx8qm-cgtqmx8.dts b/arch/arm/dts/imx8qm-cgtqmx8.dts
new file mode 100644
index 0000000000..79a99ddb10
--- /dev/null
+++ b/arch/arm/dts/imx8qm-cgtqmx8.dts
@@ -0,0 +1,427 @@
+// SPDX-License-Identifier:	GPL-2.0+
+/*
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ * Copyright 2017 NXP
+ * Copyright 2017 congatec AG
+ * Copyright (C) 2019 Oliver Graute <oliver.graute@kococonnector.com>
+ */
+
+/dts-v1/;
+
+/* First 128KB is for PSCI ATF. */
+/memreserve/ 0x80000000 0x00020000;
+
+#include "fsl-imx8qm.dtsi"
+
+/ {
+	model = "Congatec QMX8 Qseven series";
+	compatible = "fsl,imx8qm-qmx8", "fsl,imx8qm";
+
+	chosen {
+		bootargs = "console=ttyLP0,115200 earlycon=lpuart32,0x5a060000,115200";
+		stdout-path = &lpuart0;
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reg_usdhc2_vmmc: usdhc2_vmmc {
+			compatible = "regulator-fixed";
+			regulator-name = "sw-3p3-sd1";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio4 7 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+			off-on-delay-us = <3000>;
+		};
+
+		reg_usdhc3_vmmc: usdhc3_vmmc {
+			compatible = "regulator-fixed";
+			regulator-name = "sw-3p3-sd2";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio4 9 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+			off-on-delay-us = <3000>;
+		};
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy0>;
+	fsl,magic-packet;
+	fsl,rgmii_txc_dly;
+	fsl,rgmii_rxc_dly;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <6>;
+			at803x,eee-disabled;
+			at803x,vddio-1p8v;
+		};
+	};
+};
+
+&gpio2 {
+	status = "okay";
+};
+
+&gpio5 {
+	status = "okay";
+};
+
+&i2c0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpi2c0>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	rtc_ext: m41t62@68 {
+		compatible = "st,m41t62";
+		reg = <0x68>;
+	};
+};
+
+&i2c1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpi2c1>;
+	status = "okay";
+
+	wm8904: wm8904@1a {
+		compatible = "wlf,wm8904";
+		reg = <0x1a>;
+
+		clocks = <&clk IMX8QM_AUD_MCLKOUT0>;
+		clock-names = "mclk";
+		wlf,shared-lrclk;
+		/* power-domains = <&pd_mclk_out0>; */
+
+		assigned-clocks = <&clk IMX8QM_AUD_PLL0_DIV>,
+				<&clk IMX8QM_AUD_ACM_AUD_PLL_CLK0_DIV>,
+				<&clk IMX8QM_AUD_ACM_AUD_REC_CLK0_DIV>,
+				<&clk IMX8QM_AUD_MCLKOUT0>;
+
+		assigned-clock-rates = <786432000>, <49152000>, <24576000>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	imx8qm-qmx8 {
+
+		pinctrl_hog: hoggrp{
+			fsl,pins = <
+				SC_P_M40_GPIO0_01_LSIO_GPIO0_IO09		0x00000021
+				SC_P_USB_SS3_TC1_LSIO_GPIO4_IO04		0x00000021
+				SC_P_M40_GPIO0_00_LSIO_GPIO0_IO08		0x00000021
+				SC_P_ESAI1_SCKT_LSIO_GPIO2_IO07			0x00000021
+				SC_P_SPDIF0_TX_LSIO_GPIO2_IO15			0x00000021
+				SC_P_FLEXCAN1_RX_LSIO_GPIO3_IO31		0x00000021
+				SC_P_ESAI1_TX0_LSIO_GPIO2_IO08			0x00000021
+				SC_P_FLEXCAN1_TX_LSIO_GPIO4_IO00		0x00000021
+				SC_P_ESAI1_TX1_LSIO_GPIO2_IO09			0x00000021
+			>;
+		};
+
+		pinctrl_fec1: fec1grp {
+			fsl,pins = <
+				SC_P_ENET0_MDC_CONN_ENET0_MDC			0x06000020
+				SC_P_ENET0_MDIO_CONN_ENET0_MDIO			0x06000020
+				SC_P_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL	0x06000020
+				SC_P_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC	0x06000020
+				SC_P_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0	0x06000020
+				SC_P_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1	0x06000020
+				SC_P_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2	0x06000020
+				SC_P_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3	0x06000020
+				SC_P_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC	0x06000020
+				SC_P_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL	0x06000020
+				SC_P_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0	0x06000020
+				SC_P_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1	0x06000020
+				SC_P_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2	0x06000020
+				SC_P_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3	0x06000020
+			>;
+		};
+
+		pinctrl_lpi2c0: lpi2c0grp {
+			fsl,pins = <
+				SC_P_HDMI_TX0_TS_SCL_DMA_I2C0_SCL	0xc600004c
+				SC_P_HDMI_TX0_TS_SDA_DMA_I2C0_SDA	0xc600004c
+			>;
+		};
+
+		pinctrl_lpi2c1: lpi2c1grp {
+			fsl,pins = <
+				SC_P_GPT0_CLK_DMA_I2C1_SCL		0xc600004c
+				SC_P_GPT0_CAPTURE_DMA_I2C1_SDA		0xc600004c
+			>;
+		};
+
+		pinctrl_lpuart0: lpuart0grp {
+			fsl,pins = <
+				SC_P_UART0_RX_DMA_UART0_RX		0x06000020
+				SC_P_UART0_TX_DMA_UART0_TX		0x06000020
+			>;
+		};
+
+		pinctrl_lpuart1: lpuart1grp {
+			fsl,pins = <
+				SC_P_UART1_RX_DMA_UART1_RX		0x06000020
+				SC_P_UART1_TX_DMA_UART1_TX		0x06000020
+				SC_P_UART1_CTS_B_DMA_UART1_CTS_B	0x06000020
+				SC_P_UART1_RTS_B_DMA_UART1_RTS_B	0x06000020
+			>;
+		};
+
+		pinctrl_lpuart3: lpuart3grp {
+			fsl,pins = <
+				SC_P_M41_GPIO0_00_DMA_UART3_RX		0x06000020
+				SC_P_M41_GPIO0_01_DMA_UART3_TX		0x06000020
+			>;
+		};
+
+		pinctrl_mlb: mlbgrp {
+			fsl,pins = <
+				SC_P_MLB_SIG_CONN_MLB_SIG		0x21
+				SC_P_MLB_CLK_CONN_MLB_CLK		0x21
+				SC_P_MLB_DATA_CONN_MLB_DATA		0x21
+			>;
+		};
+
+		pinctrl_isl29023: isl29023grp {
+			fsl,pins = <
+				SC_P_ADC_IN2_LSIO_GPIO3_IO20		0x00000021
+			>;
+		};
+
+		pinctrl_usdhc1: usdhc1grp {
+			fsl,pins = <
+				SC_P_EMMC0_CLK_CONN_EMMC0_CLK		0x06000041
+				SC_P_EMMC0_CMD_CONN_EMMC0_CMD		0x00000021
+				SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0	0x00000021
+				SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1	0x00000021
+				SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2	0x00000021
+				SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3	0x00000021
+				SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4	0x00000021
+				SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5	0x00000021
+				SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6	0x00000021
+				SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7	0x00000021
+				SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE	0x00000041
+				SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B	0x00000021
+			>;
+		};
+
+		pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+			fsl,pins = <
+				SC_P_EMMC0_CLK_CONN_EMMC0_CLK		0x06000040
+				SC_P_EMMC0_CMD_CONN_EMMC0_CMD		0x00000020
+				SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0	0x00000020
+				SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1	0x00000020
+				SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2	0x00000020
+				SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3	0x00000020
+				SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4	0x00000020
+				SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5	0x00000020
+				SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6	0x00000020
+				SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7	0x00000020
+				SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE	0x00000040
+				SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B	0x00000020
+			>;
+		};
+
+		pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+			fsl,pins = <
+				SC_P_EMMC0_CLK_CONN_EMMC0_CLK		0x06000040
+				SC_P_EMMC0_CMD_CONN_EMMC0_CMD		0x00000020
+				SC_P_EMMC0_DATA0_CONN_EMMC0_DATA0	0x00000020
+				SC_P_EMMC0_DATA1_CONN_EMMC0_DATA1	0x00000020
+				SC_P_EMMC0_DATA2_CONN_EMMC0_DATA2	0x00000020
+				SC_P_EMMC0_DATA3_CONN_EMMC0_DATA3	0x00000020
+				SC_P_EMMC0_DATA4_CONN_EMMC0_DATA4	0x00000020
+				SC_P_EMMC0_DATA5_CONN_EMMC0_DATA5	0x00000020
+				SC_P_EMMC0_DATA6_CONN_EMMC0_DATA6	0x00000020
+				SC_P_EMMC0_DATA7_CONN_EMMC0_DATA7	0x00000020
+				SC_P_EMMC0_STROBE_CONN_EMMC0_STROBE	0x00000040
+				SC_P_EMMC0_RESET_B_CONN_EMMC0_RESET_B	0x00000020
+			>;
+		};
+
+		pinctrl_usdhc2_gpio: usdhc2grpgpio {
+			fsl,pins = <
+				SC_P_USDHC1_DATA6_LSIO_GPIO5_IO21	0x00000021
+				SC_P_USDHC1_DATA7_LSIO_GPIO5_IO22	0x00000021
+				SC_P_USDHC1_RESET_B_LSIO_GPIO4_IO07	0x00000021
+			>;
+		};
+
+		pinctrl_usdhc2: usdhc2grp {
+			fsl,pins = <
+				SC_P_USDHC1_CLK_CONN_USDHC1_CLK		0x06000041
+				SC_P_USDHC1_CMD_CONN_USDHC1_CMD		0x00000021
+				SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0	0x00000021
+				SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1	0x00000021
+				SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2	0x00000021
+				SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3	0x00000021
+				SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT	0x00000021
+			>;
+		};
+
+		pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+			fsl,pins = <
+				SC_P_USDHC1_CLK_CONN_USDHC1_CLK		0x06000040
+				SC_P_USDHC1_CMD_CONN_USDHC1_CMD		0x00000020
+				SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0	0x00000020
+				SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1	0x00000020
+				SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2	0x00000020
+				SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3	0x00000020
+				SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT	0x00000020
+			>;
+		};
+
+		pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+			fsl,pins = <
+				SC_P_USDHC1_CLK_CONN_USDHC1_CLK		0x06000040
+				SC_P_USDHC1_CMD_CONN_USDHC1_CMD		0x00000020
+				SC_P_USDHC1_DATA0_CONN_USDHC1_DATA0	0x00000020
+				SC_P_USDHC1_DATA1_CONN_USDHC1_DATA1	0x00000020
+				SC_P_USDHC1_DATA2_CONN_USDHC1_DATA2	0x00000020
+				SC_P_USDHC1_DATA3_CONN_USDHC1_DATA3	0x00000020
+				SC_P_USDHC1_VSELECT_CONN_USDHC1_VSELECT	0x00000020
+			>;
+		};
+
+		pinctrl_usdhc3_gpio: usdhc3grpgpio {
+			fsl,pins = <
+				SC_P_USDHC2_RESET_B_LSIO_GPIO4_IO09	0x00000021
+				SC_P_USDHC2_CD_B_LSIO_GPIO4_IO12	0x00000021
+			>;
+		};
+
+		pinctrl_usdhc3: usdhc3grp {
+			fsl,pins = <
+				SC_P_USDHC2_CLK_CONN_USDHC2_CLK		0x06000041
+				SC_P_USDHC2_CMD_CONN_USDHC2_CMD		0x00000021
+				SC_P_USDHC2_DATA0_CONN_USDHC2_DATA0	0x00000021
+				SC_P_USDHC2_DATA1_CONN_USDHC2_DATA1	0x00000021
+				SC_P_USDHC2_DATA2_CONN_USDHC2_DATA2	0x00000021
+				SC_P_USDHC2_DATA3_CONN_USDHC2_DATA3	0x00000021
+				SC_P_USDHC2_VSELECT_CONN_USDHC2_VSELECT	0x00000021
+			>;
+		};
+
+		pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+			fsl,pins = <
+				SC_P_USDHC2_CLK_CONN_USDHC2_CLK		0x06000040
+				SC_P_USDHC2_CMD_CONN_USDHC2_CMD		0x00000020
+				SC_P_USDHC2_DATA0_CONN_USDHC2_DATA0	0x00000020
+				SC_P_USDHC2_DATA1_CONN_USDHC2_DATA1	0x00000020
+				SC_P_USDHC2_DATA2_CONN_USDHC2_DATA2	0x00000020
+				SC_P_USDHC2_DATA3_CONN_USDHC2_DATA3	0x00000020
+				SC_P_USDHC2_VSELECT_CONN_USDHC2_VSELECT	0x00000020
+			>;
+		};
+
+		pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+			fsl,pins = <
+				SC_P_USDHC2_CLK_CONN_USDHC2_CLK		0x06000040
+				SC_P_USDHC2_CMD_CONN_USDHC2_CMD		0x00000020
+				SC_P_USDHC2_DATA0_CONN_USDHC2_DATA0	0x00000020
+				SC_P_USDHC2_DATA1_CONN_USDHC2_DATA1	0x00000020
+				SC_P_USDHC2_DATA2_CONN_USDHC2_DATA2	0x00000020
+				SC_P_USDHC2_DATA3_CONN_USDHC2_DATA3	0x00000020
+				SC_P_USDHC2_VSELECT_CONN_USDHC2_VSELECT	0x00000020
+			>;
+		};
+/*
+		pinctrl_usbotg1: usbotg1 {
+			fsl,pins = <
+				SC_P_USB_SS3_TC0_CONN_USB_OTG1_PWR		0x00000021
+			>;
+		};
+*/
+	};
+};
+
+&lpuart0 { /* console */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart0>;
+	status = "okay";
+};
+
+&lpuart1 { /* Q7 connector */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart1>;
+	status = "okay";
+};
+
+&pd_dma_lpuart0 {
+	debug_console;
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	bus-width = <4>;
+	cd-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio5 21 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	fsl,tuning-start-tap = <20>;
+	fsl,tuning-step= <2>;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>, <&pinctrl_usdhc3_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>, <&pinctrl_usdhc3_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>, <&pinctrl_usdhc3_gpio>;
+	bus-width = <4>;
+	cd-gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&reg_usdhc3_vmmc>;
+	fsl,tuning-start-tap = <20>;
+	fsl,tuning-step= <2>;
+	status = "okay";
+};
+/*
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	power-polarity-active-high;
+	disable-over-current;
+	status = "okay";
+};
+
+&usb2 {
+	status = "okay";
+};
+*/
diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile
index fbd99a3499..891631055a 100644
--- a/arch/arm/mach-imx/Makefile
+++ b/arch/arm/mach-imx/Makefile
@@ -152,10 +152,8 @@ ifeq ($(DEPFILE_EXISTS),0)
 endif
 
 flash.bin: spl/u-boot-spl-ddr.bin u-boot.itb FORCE
-ifeq ($(DEPFILE_EXISTS),0)
 	$(call if_changed,mkimage)
 endif
-endif
 
 ifeq ($(CONFIG_ARCH_IMX8), y)
 SPL:
diff --git a/arch/arm/mach-imx/imx8/Kconfig b/arch/arm/mach-imx/imx8/Kconfig
index d17760e333..d47946d744 100644
--- a/arch/arm/mach-imx/imx8/Kconfig
+++ b/arch/arm/mach-imx/imx8/Kconfig
@@ -55,6 +55,12 @@ config TARGET_IMX8QM_MEK
 	select BOARD_LATE_INIT
 	select IMX8QM
 
+config TARGET_CONGA_QMX8
+	bool "Support congatec conga-QMX8 board"
+	select BOARD_LATE_INIT
+	select SUPPORT_SPL
+	select IMX8QM
+
 config TARGET_IMX8QXP_MEK
 	bool "Support i.MX8QXP MEK board"
 	select BOARD_LATE_INIT
@@ -64,6 +70,7 @@ endchoice
 
 source "board/freescale/imx8qm_mek/Kconfig"
 source "board/freescale/imx8qxp_mek/Kconfig"
+source "board/congatec/cgtqmx8/Kconfig"
 source "board/toradex/apalis-imx8/Kconfig"
 source "board/toradex/colibri-imx8x/Kconfig"
 
diff --git a/board/congatec/cgtqmx8/Kconfig b/board/congatec/cgtqmx8/Kconfig
new file mode 100644
index 0000000000..7273039261
--- /dev/null
+++ b/board/congatec/cgtqmx8/Kconfig
@@ -0,0 +1,14 @@
+if TARGET_CONGA_QMX8
+
+config SYS_BOARD
+	default "cgtqmx8"
+
+config SYS_VENDOR
+	default "congatec"
+
+config SYS_CONFIG_NAME
+	default "cgtqmx8"
+
+source "board/congatec/common/Kconfig"
+
+endif
diff --git a/board/congatec/cgtqmx8/MAINTAINERS b/board/congatec/cgtqmx8/MAINTAINERS
new file mode 100644
index 0000000000..a242e534c8
--- /dev/null
+++ b/board/congatec/cgtqmx8/MAINTAINERS
@@ -0,0 +1,6 @@
+i.MX8QM CGTQMX8 BOARD
+M:	Oliver Graute <oliver.graute@kococonnector.com>
+S:	Maintained
+F:	board/congatec/cgtqmx8/
+F:	include/configs/cgtqmx8.h
+F:	configs/cgtqmx8_defconfig
diff --git a/board/congatec/cgtqmx8/Makefile b/board/congatec/cgtqmx8/Makefile
new file mode 100644
index 0000000000..4b59dbb6bc
--- /dev/null
+++ b/board/congatec/cgtqmx8/Makefile
@@ -0,0 +1,11 @@
+#
+# Copyright 2017 NXP
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y += cgtqmx8.o
+
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+endif
diff --git a/board/congatec/cgtqmx8/README b/board/congatec/cgtqmx8/README
new file mode 100644
index 0000000000..5724eb89f7
--- /dev/null
+++ b/board/congatec/cgtqmx8/README
@@ -0,0 +1,15 @@
+Build U-Boot
+============
+
+$ export ATF_LOAD_ADDR=0x80000000
+$ export BL33_LOAD_ADDR=0x80020000
+$ make cgtqmx8_defconfig
+$ make u-boot.bin
+$ make flash.bin
+
+Flash the binary into the SD card
+=================================
+
+Burn the flash.bin binary to SD card offset 32KB:
+
+$ sudo dd if=flash.bin of=/dev/sd[x] bs=1k seek=32 conv=fsync
diff --git a/board/congatec/cgtqmx8/cgtqmx8.c b/board/congatec/cgtqmx8/cgtqmx8.c
new file mode 100644
index 0000000000..d0f5f62c41
--- /dev/null
+++ b/board/congatec/cgtqmx8/cgtqmx8.c
@@ -0,0 +1,478 @@
+//SPDX-License-Identifier:	GPL-2.0+
+/*
+ * Copyright 2018 congatec AG
+ * Copyright (C) 2019 Oliver Graute <oliver.graute@kococonnector.com>
+ */
+#include <common.h>
+#include <errno.h>
+#include <linux/libfdt.h>
+#include <fsl_esdhc.h>
+
+#include <asm/io.h>
+#include <asm/gpio.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sci/sci.h>
+#include <asm/arch/imx8-pins.h>
+#include <usb.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/sys_proto.h>
+#include <power-domain.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define ESDHC_PAD_CTRL	((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \
+		(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+		(SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+		(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define ESDHC_CLK_PAD_CTRL	((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \
+			(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+			(SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+			(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define ENET_INPUT_PAD_CTRL	((SC_PAD_CONFIG_OD_IN << PADRING_CONFIG_SHIFT) | \
+			(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+			(SC_PAD_28FDSOI_DSE_18V_10MA << PADRING_DSE_SHIFT) | \
+			(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define ENET_NORMAL_PAD_CTRL	((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \
+			(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+			(SC_PAD_28FDSOI_DSE_18V_10MA << PADRING_DSE_SHIFT) | \
+			(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define FSPI_PAD_CTRL	((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \
+			(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+			(SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+			(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define GPIO_PAD_CTRL	((SC_PAD_CONFIG_NORMAL << PADRING_CONFIG_SHIFT) | \
+			(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+			(SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+			(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define I2C_PAD_CTRL	((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \
+			(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+			(SC_PAD_28FDSOI_DSE_DV_LOW << PADRING_DSE_SHIFT) | \
+			(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+#define UART_PAD_CTRL	((SC_PAD_CONFIG_OUT_IN << PADRING_CONFIG_SHIFT) | \
+			(SC_PAD_ISO_OFF << PADRING_LPCONFIG_SHIFT) | \
+			(SC_PAD_28FDSOI_DSE_DV_HIGH << PADRING_DSE_SHIFT) | \
+			(SC_PAD_28FDSOI_PS_PU << PADRING_PULL_SHIFT))
+
+static iomux_cfg_t uart0_pads[] = {
+	SC_P_UART0_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	SC_P_UART0_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+	imx8_iomux_setup_multiple_pads(uart0_pads, ARRAY_SIZE(uart0_pads));
+}
+
+int board_early_init_f(void)
+{
+	/* sc_ipc_t ipcHndl = 0; */
+	sc_err_t sciErr = 0;
+
+	/* When start u-boot in XEN VM, directly return */
+	/* if (IS_ENABLED(CONFIG_XEN)) */
+		/* return 0; */
+
+	/* ipcHndl = gd->arch.ipc_channel_handle; */
+
+	/* Power up UART0, this is very early while power domain is not working */
+	sciErr = sc_pm_set_resource_power_mode(-1, SC_R_UART_0, SC_PM_PW_MODE_ON);
+	if (sciErr != SC_ERR_NONE)
+		return 0;
+
+	/* Set UART0 clock root to 80 MHz */
+	sc_pm_clock_rate_t rate = 80000000;
+	sciErr = sc_pm_set_clock_rate(-1, SC_R_UART_0, 2, &rate);
+	if (sciErr != SC_ERR_NONE)
+		return 0;
+
+	/* Enable UART0 clock root */
+	sciErr = sc_pm_clock_enable(-1, SC_R_UART_0, 2, true, false);
+	if (sciErr != SC_ERR_NONE)
+		return 0;
+
+	setup_iomux_uart();
+
+	return 0;
+}
+
+#ifdef CONFIG_FSL_ESDHC
+
+#define USDHC1_CD_GPIO	IMX_GPIO_NR(5, 22)
+#define USDHC2_CD_GPIO	IMX_GPIO_NR(4, 12)
+
+static struct fsl_esdhc_cfg usdhc_cfg[CONFIG_SYS_FSL_USDHC_NUM] = {
+	{USDHC1_BASE_ADDR, 0, 8},
+	{USDHC2_BASE_ADDR, 0, 4},
+	{USDHC3_BASE_ADDR, 0, 4},
+};
+
+static iomux_cfg_t emmc0[] = {
+	SC_P_EMMC0_CLK | MUX_PAD_CTRL(ESDHC_CLK_PAD_CTRL),
+	SC_P_EMMC0_CMD | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_DATA0 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_DATA1 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_DATA2 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_DATA3 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_DATA4 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_DATA5 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_DATA6 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_DATA7 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_RESET_B | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_EMMC0_STROBE | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+};
+
+static iomux_cfg_t usdhc1_sd[] = {
+	SC_P_USDHC1_CLK | MUX_PAD_CTRL(ESDHC_CLK_PAD_CTRL),
+	SC_P_USDHC1_CMD | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC1_DATA0 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC1_DATA1 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC1_DATA2 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC1_DATA3 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC1_DATA6 | MUX_MODE_ALT(2) | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC1_DATA7 | MUX_MODE_ALT(3) | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC1_RESET_B | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC1_VSELECT | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+};
+
+static iomux_cfg_t usdhc2_sd[] = {
+	SC_P_USDHC2_CLK | MUX_PAD_CTRL(ESDHC_CLK_PAD_CTRL),
+	SC_P_USDHC2_CMD | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC2_DATA0 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC2_DATA1 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC2_DATA2 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC2_DATA3 | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC2_RESET_B | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC2_VSELECT | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC2_WP | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+	SC_P_USDHC2_CD_B | MUX_MODE_ALT(3) | MUX_PAD_CTRL(ESDHC_PAD_CTRL),
+};
+
+int board_mmc_init(bd_t *bis)
+{
+	int i, ret;
+	struct power_domain pd;
+
+	/*
+	 * According to the board_mmc_init() the following map is done:
+	 * (U-Boot device node)    (Physical Port)
+	 * mmc0 (onboard eMMC)     USDHC1
+	 * mmc1 (external SD card) USDHC2
+	 * mmc2 (onboard µSD)      USDHC3
+	 */
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+		  /* onboard eMMC */
+			if (!power_domain_lookup_name("conn_sdhc0", &pd))
+				power_domain_on(&pd);
+
+			imx8_iomux_setup_multiple_pads(emmc0, ARRAY_SIZE(emmc0));
+			init_clk_usdhc(0);
+			usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+			break;
+		case 1:
+		  /* external SD card */
+			if (!power_domain_lookup_name("conn_sdhc1", &pd))
+				power_domain_on(&pd);
+
+			imx8_iomux_setup_multiple_pads(usdhc1_sd, ARRAY_SIZE(usdhc1_sd));
+			init_clk_usdhc(1);
+			usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+			gpio_request(USDHC1_CD_GPIO, "sd1_cd");
+			gpio_direction_input(USDHC1_CD_GPIO);
+			break;
+		case 2:
+		  /* onboard µSD */
+			if (!power_domain_lookup_name("conn_sdhc2", &pd))
+				power_domain_on(&pd);
+
+			imx8_iomux_setup_multiple_pads(usdhc2_sd, ARRAY_SIZE(usdhc2_sd));
+			init_clk_usdhc(2);
+			usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+			gpio_request(USDHC2_CD_GPIO, "sd2_cd");
+			gpio_direction_input(USDHC2_CD_GPIO);
+			break;
+		default:
+			printf("Warning: you configured more USDHC controllers"
+				"(%d) than supported by the board\n", i + 1);
+			return 0;
+		}
+		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+		if (ret) {
+			printf("Warning: failed to initialize mmc dev %d\n", i);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+	int ret = 0;
+
+	switch (cfg->esdhc_base) {
+	case USDHC1_BASE_ADDR:
+		ret = 1;
+		break;
+	case USDHC2_BASE_ADDR:
+		ret = !gpio_get_value(USDHC1_CD_GPIO);
+		break;
+	case USDHC3_BASE_ADDR:
+		ret = !gpio_get_value(USDHC2_CD_GPIO);
+		break;
+	}
+
+	return ret;
+}
+
+#endif /* CONFIG_FSL_ESDHC */
+
+#ifdef CONFIG_FEC_MXC
+#include <miiphy.h>
+
+static iomux_cfg_t pad_enet0[] = {
+	SC_P_ENET0_RGMII_RX_CTL | MUX_PAD_CTRL(ENET_INPUT_PAD_CTRL),
+	SC_P_ENET0_RGMII_RXD0 | MUX_PAD_CTRL(ENET_INPUT_PAD_CTRL),
+	SC_P_ENET0_RGMII_RXD1 | MUX_PAD_CTRL(ENET_INPUT_PAD_CTRL),
+	SC_P_ENET0_RGMII_RXD2 | MUX_PAD_CTRL(ENET_INPUT_PAD_CTRL),
+	SC_P_ENET0_RGMII_RXD3 | MUX_PAD_CTRL(ENET_INPUT_PAD_CTRL),
+	SC_P_ENET0_RGMII_RXC | MUX_PAD_CTRL(ENET_INPUT_PAD_CTRL),
+	SC_P_ENET0_RGMII_TX_CTL | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL),
+	SC_P_ENET0_RGMII_TXD0 | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL),
+	SC_P_ENET0_RGMII_TXD1 | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL),
+	SC_P_ENET0_RGMII_TXD2 | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL),
+	SC_P_ENET0_RGMII_TXD3 | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL),
+	SC_P_ENET0_RGMII_TXC | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL),
+	SC_P_ENET0_MDC | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL),
+	SC_P_ENET0_MDIO | MUX_PAD_CTRL(ENET_NORMAL_PAD_CTRL),
+};
+
+static void setup_iomux_fec(void)
+{
+	imx8_iomux_setup_multiple_pads(pad_enet0, ARRAY_SIZE(pad_enet0));
+}
+
+static void enet_device_phy_reset(void)
+{
+	gpio_set_value(FEC0_RESET, 0);
+	udelay(50);
+	gpio_set_value(FEC0_RESET, 1);
+
+	/* The board has a long delay for this reset to become stable */
+	mdelay(200);
+}
+
+int board_eth_init(bd_t *bis)
+{
+	int ret;
+	struct power_domain pd0;
+
+	/* if (!power_domain_lookup_name(FEC0_PDOMAIN, &pd0)) */
+	  /* power_domain_on(&pd0); */
+
+	setup_iomux_fec();
+
+	/* ret = fecmxc_initialize_multi(bis, CONFIG_FEC_ENET_DEV, */
+		/* CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE); */
+	if (ret)
+		printf("FEC0 MXC: %s:failed\n", __func__);
+
+	return ret;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
+
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x00);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x82ee);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+
+static int setup_fec(void)
+{
+	/* Reset ENET PHY */
+	enet_device_phy_reset();
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_MXC_GPIO
+
+#define LVDS_ENABLE IMX_GPIO_NR(1, 6)
+#define BKL_ENABLE  IMX_GPIO_NR(1, 7)
+
+static iomux_cfg_t board_gpios[] = {
+	SC_P_LVDS0_I2C0_SCL | MUX_MODE_ALT(3) | MUX_PAD_CTRL(GPIO_PAD_CTRL),
+	SC_P_LVDS0_I2C0_SDA | MUX_MODE_ALT(3) | MUX_PAD_CTRL(GPIO_PAD_CTRL),
+	SC_P_ESAI1_FST | MUX_MODE_ALT(3) | MUX_PAD_CTRL(GPIO_PAD_CTRL),
+};
+
+static void board_gpio_init(void)
+{
+	imx8_iomux_setup_multiple_pads(board_gpios, ARRAY_SIZE(board_gpios));
+
+	/* enable LVDS */
+	gpio_request(LVDS_ENABLE, "lvds_enable");
+	gpio_direction_output(LVDS_ENABLE, 1);
+
+	/* enable backlight */
+	gpio_request(BKL_ENABLE, "bkl_enable");
+	gpio_direction_output(BKL_ENABLE, 1);
+
+	/* ethernet reset */
+	gpio_request(FEC0_RESET, "enet0_reset");
+	gpio_direction_output(FEC0_RESET, 1);
+}
+#endif
+
+int checkboard(void)
+{
+	puts("Board: conga-QMX8\n");
+
+	build_info();
+	print_bootinfo();
+
+	/* Note:  After reloc, ipcHndl will no longer be valid.  If handle
+	 *        returned by sc_ipc_open matches SC_IPC_CH, use this
+	 *        macro (valid after reloc) for subsequent SCI calls.
+	 */
+	/*
+	if (gd->arch.ipc_channel_handle != SC_IPC_CH) {
+		printf("\nSCI error! Invalid handle\n");
+	}
+	*/
+
+	return 0;
+}
+
+int board_init(void)
+{
+	if (IS_ENABLED(CONFIG_XEN))
+		return 0;
+
+#ifdef CONFIG_MXC_GPIO
+	board_gpio_init();
+#endif
+
+#ifdef CONFIG_FEC_MXC
+	setup_fec();
+#endif
+
+	return 0;
+}
+
+void detail_board_ddr_info(void)
+{
+	puts("\nDDR    ");
+}
+
+/*
+ * Board specific reset that is system reset.
+ */
+void reset_cpu(ulong addr)
+{
+/*
+	puts("SCI reboot request");
+	sc_pm_reboot(SC_IPC_CH, SC_PM_RESET_TYPE_COLD);
+	while (1)
+		putc('.');
+*/
+	/* TODO */
+}
+
+
+#ifdef CONFIG_OF_BOARD_SETUP
+int ft_board_setup(void *blob, bd_t *bd)
+{
+	return 0;
+}
+#endif
+
+int board_mmc_get_env_dev(int devno)
+{
+	/* Use EMMC */
+	if (IS_ENABLED(CONFIG_XEN))
+		return 0;
+
+	return devno;
+}
+
+int mmc_map_to_kernel_blk(int dev_no)
+{
+	/* Use EMMC */
+	if (IS_ENABLED(CONFIG_XEN))
+		return 0;
+
+	return dev_no;
+}
+
+extern uint32_t _end_ofs;
+int board_late_init(void)
+{
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+	env_set("board_name", "QMX8");
+	env_set("board_rev", "iMX8QM");
+#endif
+
+	env_set("sec_boot", "no");
+#ifdef CONFIG_AHAB_BOOT
+	env_set("sec_boot", "yes");
+#endif
+
+#ifdef CONFIG_ENV_IS_IN_MMC
+	board_late_mmc_env_init();
+#endif
+
+#ifdef IMX_LOAD_HDMI_FIMRWARE
+	char *end_of_uboot;
+	char command[256];
+	end_of_uboot = (char *)(ulong)(CONFIG_SYS_TEXT_BASE + _end_ofs + fdt_totalsize(gd->fdt_blob));
+	end_of_uboot += 9;
+
+	/* load hdmitxfw.bin and hdmirxfw.bin*/
+	memcpy(IMX_HDMI_FIRMWARE_LOAD_ADDR, end_of_uboot,
+			IMX_HDMITX_FIRMWARE_SIZE + IMX_HDMIRX_FIRMWARE_SIZE);
+
+	sprintf(command, "hdp load 0x%x", IMX_HDMI_FIRMWARE_LOAD_ADDR);
+	run_command(command, 0);
+
+	sprintf(command, "hdprx load 0x%x",
+			IMX_HDMI_FIRMWARE_LOAD_ADDR + IMX_HDMITX_FIRMWARE_SIZE);
+	run_command(command, 0);
+#endif
+
+	return 0;
+}
+
+#ifdef CONFIG_FSL_FASTBOOT
+#ifdef CONFIG_ANDROID_RECOVERY
+int is_recovery_key_pressing(void)
+{
+	return 0; /*TODO*/
+}
+#endif /*CONFIG_ANDROID_RECOVERY*/
+#endif /*CONFIG_FSL_FASTBOOT*/
+
+/* Only Enable USB3 resources currently */
+int board_usb_init(int index, enum usb_init_type init)
+{
+	return 0;
+}
diff --git a/board/congatec/cgtqmx8/imximage.cfg b/board/congatec/cgtqmx8/imximage.cfg
new file mode 100644
index 0000000000..e324c7ca37
--- /dev/null
+++ b/board/congatec/cgtqmx8/imximage.cfg
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier:	GPL-2.0+ */
+/*
+ * Copyright 2018 NXP
+ */
+
+#define __ASSEMBLY__
+
+/* Boot from SD, sector size 0x400 */
+BOOT_FROM SD 0x400
+/* SoC type IMX8QM */
+SOC_TYPE IMX8QM
+/* Append seco container image */
+APPEND mx8qm-ahab-container.img
+/* Create the 2nd container */
+CONTAINER
+/* Add scfw image with exec attribute */
+IMAGE SCU mx8qm-val-scfw-tcm.bin
+/* Add ATF image with exec attribute */
+IMAGE A35 bl31.bin 0x80000000
+/* Add U-Boot image with load attribute */
+DATA A35 u-boot-dtb.bin 0x80020000
diff --git a/board/congatec/cgtqmx8/spl.c b/board/congatec/cgtqmx8/spl.c
new file mode 100644
index 0000000000..95ce9f37e8
--- /dev/null
+++ b/board/congatec/cgtqmx8/spl.c
@@ -0,0 +1,75 @@
+/*
+ * Copyright 2018 NXP
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <spl.h>
+#include <dm/uclass.h>
+#include <dm/device.h>
+#include <dm/uclass-internal.h>
+#include <dm/device-internal.h>
+#include <dm/lists.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void spl_board_init(void)
+{
+	struct udevice *dev;
+	int offset;
+
+	uclass_find_first_device(UCLASS_MISC, &dev);
+
+	for (; dev; uclass_find_next_device(&dev)) {
+		if (device_probe(dev))
+			continue;
+	}
+
+	offset = fdt_node_offset_by_compatible(gd->fdt_blob, -1, "nxp,imx8-pd");
+	while (offset != -FDT_ERR_NOTFOUND) {
+		lists_bind_fdt(gd->dm_root, offset_to_ofnode(offset),
+			       NULL, true);
+		offset = fdt_node_offset_by_compatible(gd->fdt_blob, offset,
+						       "nxp,imx8-pd");
+	}
+
+	uclass_find_first_device(UCLASS_POWER_DOMAIN, &dev);
+
+	for (; dev; uclass_find_next_device(&dev)) {
+		if (device_probe(dev))
+			continue;
+	}
+
+	arch_cpu_init();
+
+	board_early_init_f();
+
+	timer_init();
+
+	preloader_console_init();
+
+	puts("Normal Boot\n");
+}
+
+#ifdef CONFIG_SPL_LOAD_FIT
+int board_fit_config_name_match(const char *name)
+{
+	/* Just empty function now - can't decide what to choose */
+	debug("%s: %s\n", __func__, name);
+
+	return 0;
+}
+#endif
+
+void board_init_f(ulong dummy)
+{
+	/* Clear global data */
+	memset((void *)gd, 0, sizeof(gd_t));
+
+	/* Clear the BSS. */
+	memset(__bss_start, 0, __bss_end - __bss_start);
+
+	board_init_r(NULL, 0);
+}
diff --git a/board/congatec/common/Kconfig b/board/congatec/common/Kconfig
new file mode 100644
index 0000000000..5c205bd830
--- /dev/null
+++ b/board/congatec/common/Kconfig
@@ -0,0 +1,48 @@
+if !ARCH_IMX8M && !ARCH_IMX8
+
+config CHAIN_OF_TRUST
+	depends on !FIT_SIGNATURE && SECURE_BOOT
+	imply CMD_BLOB
+	imply CMD_HASH if ARM
+	select FSL_CAAM
+	select SPL_BOARD_INIT if (ARM && SPL)
+	select SHA_HW_ACCEL
+	select SHA_PROG_HW_ACCEL
+	select ENV_IS_NOWHERE
+	select CMD_EXT4 if ARM
+	select CMD_EXT4_WRITE if ARM
+	bool
+	default y
+
+config CMD_ESBC_VALIDATE
+	bool "Enable the 'esbc_validate' and 'esbc_halt' commands"
+	default y if CHAIN_OF_TRUST
+	help
+	  This option enables two commands used for secure booting:
+
+	    esbc_validate - validate signature using RSA verification
+	    esbc_halt - put the core in spin loop (Secure Boot Only)
+
+endif
+
+config VOL_MONITOR_LTC3882_READ
+	depends on VID
+	bool "Enable the LTC3882 voltage monitor read"
+	default n
+	help
+	 This option enables LTC3882 voltage monitor read
+	 functionality. It is used by common VID driver.
+
+config VOL_MONITOR_LTC3882_SET
+	depends on VID
+	bool "Enable the LTC3882 voltage monitor set"
+	default n
+	help
+	 This option enables LTC3882 voltage monitor set
+	 functionality. It is used by common VID driver.
+
+config USB_TCPC
+	bool "USB Typec port controller simple driver"
+	default n
+	help
+	  Enable USB type-c port controller (TCPC) driver
diff --git a/board/congatec/common/Makefile b/board/congatec/common/Makefile
new file mode 100644
index 0000000000..d4ddfbf971
--- /dev/null
+++ b/board/congatec/common/Makefile
@@ -0,0 +1,23 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+MINIMAL=
+
+ifdef CONFIG_SPL_BUILD
+ifdef CONFIG_SPL_INIT_MINIMAL
+MINIMAL=y
+endif
+endif
+
+ifdef MINIMAL
+# necessary to create built-in.o
+obj- := __dummy__.o
+else
+
+obj-y				+= mmc.o
+
+endif
diff --git a/board/congatec/common/mmc.c b/board/congatec/common/mmc.c
new file mode 100644
index 0000000000..9fc3e68728
--- /dev/null
+++ b/board/congatec/common/mmc.c
@@ -0,0 +1,50 @@
+/*
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ * Copyright 2018 NXP
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <linux/errno.h>
+#include <asm/io.h>
+#include <stdbool.h>
+#include <mmc.h>
+
+static int check_mmc_autodetect(void)
+{
+	char *autodetect_str = env_get("mmcautodetect");
+
+	if ((autodetect_str != NULL) &&
+		(strcmp(autodetect_str, "yes") == 0)) {
+		return 1;
+	}
+
+	return 0;
+}
+
+/* This should be defined for each board */
+__weak int mmc_map_to_kernel_blk(int dev_no)
+{
+	return dev_no;
+}
+
+void board_late_mmc_env_init(void)
+{
+	char cmd[32];
+	char mmcblk[32];
+	u32 dev_no = mmc_get_env_dev();
+
+	if (!check_mmc_autodetect())
+		return;
+
+	env_set_ulong("mmcdev", dev_no);
+
+	/* Set mmcblk env */
+	sprintf(mmcblk, "/dev/mmcblk%dp2 rootwait rw",
+		mmc_map_to_kernel_blk(dev_no));
+	env_set("mmcroot", mmcblk);
+
+	sprintf(cmd, "mmc dev %d", dev_no);
+	run_command(cmd, 0);
+}
diff --git a/configs/cgtqmx8_defconfig b/configs/cgtqmx8_defconfig
new file mode 100644
index 0000000000..1245403fbf
--- /dev/null
+++ b/configs/cgtqmx8_defconfig
@@ -0,0 +1,79 @@
+CONFIG_ARM=y
+CONFIG_SPL_SYS_ICACHE_OFF=y
+CONFIG_SPL_SYS_DCACHE_OFF=y
+CONFIG_ARCH_IMX8=y
+CONFIG_SYS_TEXT_BASE=0x80020000
+CONFIG_SPL_GPIO_SUPPORT=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_TARGET_CONGA_QMX8=y
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=3
+CONFIG_SPL=y
+CONFIG_FIT=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/congatec/cgtqmx8/imximage.cfg"
+CONFIG_BOOTDELAY=3
+CONFIG_LOG=y
+CONFIG_SPL_BOARD_INIT=y
+CONFIG_HUSH_PARSER=y
+CONFIG_SPL_SEPARATE_BSS=y
+CONFIG_SPL_POWER_SUPPORT=y
+CONFIG_SPL_POWER_DOMAIN=y
+CONFIG_SPL_WATCHDOG_SUPPORT=y
+CONFIG_CMD_CPU=y
+# CONFIG_BOOTM_NETBSD is not set
+# CONFIG_CMD_IMPORTENV is not set
+CONFIG_CMD_CLK=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_FAT=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="imx8qm-cgtqmx8"
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_SPL_DM=y
+CONFIG_SPL_CLK=y
+CONFIG_CLK_IMX8=y
+CONFIG_CPU=y
+CONFIG_DM_GPIO=y
+CONFIG_MXC_GPIO=y
+CONFIG_DM_PCA953X=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_IMX_LPI2C=y
+CONFIG_I2C_MUX=y
+CONFIG_I2C_MUX_PCA954x=y
+CONFIG_MISC=y
+CONFIG_DM_MMC=y
+CONFIG_FSL_USDHC=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_ADDR_ENABLE=y
+CONFIG_PHY_ATHEROS=y
+CONFIG_DM_ETH=y
+CONFIG_PHY_GIGE=y
+CONFIG_FEC_MXC_SHARE_MDIO=y
+CONFIG_FEC_MXC_MDIO_BASE=0x5B040000
+CONFIG_FEC_MXC=y
+CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_PINCTRL_IMX8=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_IMX8_POWER_DOMAIN=y
+CONFIG_DM_REGULATOR=y
+CONFIG_SPL_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_SPL_DM_REGULATOR_GPIO=y
+CONFIG_DM_SERIAL=y
+CONFIG_FSL_LPUART=y
+CONFIG_SPL_TINY_MEMSET=y
+# CONFIG_EFI_LOADER is not set
diff --git a/include/configs/cgtqmx8.h b/include/configs/cgtqmx8.h
new file mode 100644
index 0000000000..f29e144d9a
--- /dev/null
+++ b/include/configs/cgtqmx8.h
@@ -0,0 +1,167 @@
+// SPDX-License-Identifier:	GPL-2.0+
+/*
+ * Copyright 2017-2018 NXP
+ * Copyright 2018 congatec AG
+ *
+ */
+
+#ifndef __CGTQMX8_H
+#define __CGTQMX8_H
+
+#include <linux/sizes.h>
+#include <asm/arch/imx-regs.h>
+
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SPL_TEXT_BASE				0x0
+#define CONFIG_SPL_MAX_SIZE				(124 * 1024)
+#define CONFIG_SYS_MONITOR_LEN				(1024 * 1024)
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR		0x800
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION		0
+
+#define CONFIG_SPL_LDSCRIPT		"arch/arm/cpu/armv8/u-boot-spl.lds"
+#define CONFIG_SPL_STACK		0x013E000
+#define CONFIG_SPL_BSS_START_ADDR	0x00128000
+#define CONFIG_SPL_BSS_MAX_SIZE		0x1000	/* 4 KB */
+#define CONFIG_SYS_SPL_MALLOC_START	0x00120000
+#define CONFIG_SYS_SPL_MALLOC_SIZE	0x3000	/* 12 KB */
+#define CONFIG_SERIAL_LPUART_BASE	0x5a060000
+#define CONFIG_MALLOC_F_ADDR		0x00120000
+
+#define CONFIG_SPL_RAW_IMAGE_ARM_TRUSTED_FIRMWARE
+
+#define CONFIG_SPL_ABORT_ON_RAW_IMAGE
+
+#define CONFIG_OF_EMBED
+#endif
+
+#define CONFIG_REMAKE_ELF
+
+#define CONFIG_BOARD_EARLY_INIT_F
+
+/* Flat Device Tree Definitions */
+#define CONFIG_OF_BOARD_SETUP
+
+#undef CONFIG_CMD_EXPORTENV
+#undef CONFIG_CMD_IMPORTENV
+#undef CONFIG_CMD_IMLS
+
+#undef CONFIG_CMD_CRC32
+
+#define CONFIG_SYS_FSL_ESDHC_ADDR       0
+#define USDHC1_BASE_ADDR                0x5B010000
+#define USDHC2_BASE_ADDR                0x5B020000
+#define CONFIG_SUPPORT_EMMC_BOOT	/* eMMC specific */
+
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+
+#define FEC0_RESET IMX_GPIO_NR(2, 5)
+#define FEC0_PDOMAIN "conn_enet0"
+
+/* Initial environment variables */
+#define CONFIG_EXTRA_ENV_SETTINGS		\
+	"script=boot.scr\0" \
+	"image=Image\0" \
+	"panel=NULL\0" \
+	"console=ttyLP0\0" \
+	"fdt_addr=0x83000000\0"			\
+	"fdt_high=0xffffffffffffffff\0"		\
+	"boot_fdt=try\0" \
+	"fdt_file=imx8qm-cgt-qmx8.dtb\0" \
+	"initrd_addr=0x83800000\0"		\
+	"initrd_high=0xffffffffffffffff\0" \
+	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
+	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
+	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+	"mmcautodetect=yes\0" \
+	"mmcargs=setenv bootargs console=${console},${baudrate} root=${mmcroot} earlycon\0 " \
+	"loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+	"bootscript=echo Running bootscript from mmc ...; " \
+		"source\0" \
+	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+	"mmcboot=echo Booting from mmc ...; " \
+		"run mmcargs; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if run loadfdt; then " \
+				"booti ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"echo WARN: Cannot load the DT; " \
+			"fi; " \
+		"else " \
+			"echo wait for boot; " \
+		"fi;\0" \
+	"netargs=setenv bootargs console=${console},${baudrate} " \
+		"root=/dev/nfs " \
+		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp rw earlycon\0" \
+	"netboot=echo Booting from net ...; " \
+		"run netargs;  " \
+		"if test ${ip_dyn} = yes; then " \
+			"setenv get_cmd dhcp; " \
+		"else " \
+			"setenv get_cmd tftp; " \
+		"fi; " \
+		"${get_cmd} ${loadaddr} ${image}; " \
+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+				"booti ${loadaddr} - ${fdt_addr}; " \
+			"else " \
+				"echo WARN: Cannot load the DT; " \
+			"fi; " \
+		"else " \
+			"booti; " \
+		"fi;\0"
+
+#define CONFIG_BOOTCOMMAND \
+	   "mmc dev ${mmcdev}; if mmc rescan; then " \
+		   "if run loadbootscript; then " \
+			   "run bootscript; " \
+		   "else " \
+			   "if run loadimage; then " \
+				   "run mmcboot; " \
+			   "else run netboot; " \
+			   "fi; " \
+		   "fi; " \
+	   "else booti ${loadaddr} - ${fdt_addr}; fi"
+
+/* Link Definitions */
+#define CONFIG_LOADADDR			0x80280000
+
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
+
+#define CONFIG_SYS_INIT_SP_ADDR		0x80200000
+
+/* Default environment is in SD */
+#define CONFIG_ENV_SIZE			0x1000
+#define CONFIG_ENV_OFFSET		(64 * SZ_64K)
+#define CONFIG_SYS_MMC_ENV_PART		0	/* user area */
+
+#define CONFIG_SYS_MMC_IMG_LOAD_PART	1
+
+/* On LPDDR4 board, USDHC1 is for eMMC, USDHC2 is for SD on CPU board */
+#define CONFIG_SYS_MMC_ENV_DEV		1   /* USDHC2 */
+#define CONFIG_MMCROOT			"/dev/mmcblk1p2"  /* USDHC2 */
+#define CONFIG_SYS_FSL_USDHC_NUM	2
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		((CONFIG_ENV_SIZE + (32 * 1024)) * 1024)
+
+#define CONFIG_SYS_SDRAM_BASE		0x80000000
+#define PHYS_SDRAM_1			0x80000000
+#define PHYS_SDRAM_2			0x880000000
+#define PHYS_SDRAM_1_SIZE		0x80000000	/* 2 GB */
+#define PHYS_SDRAM_2_SIZE		0x100000000	/* 4 GB */
+
+/* Serial */
+#define CONFIG_BAUDRATE			115200
+
+/* Generic Timer Definitions */
+#define COUNTER_FREQUENCY		8000000	/* 8MHz */
+
+/* Networking */
+#define CONFIG_FEC_XCV_TYPE		RGMII
+#define FEC_QUIRK_ENET_MAC
+
+#endif /* __CGTQMX8_H */
