diff mbox series

[U-Boot,v2,07/12] armV7R: K3: am654: Load SYSFW binary and config from boot media

Message ID 20190604225555.12186-8-dannenberg@ti.com
State Accepted
Commit c222e3d927f8c2d65c44df659280793db93fea76
Delegated to: Tom Rini
Headers show
Series System Firmware Loader for TI K3 family SoCs | expand

Commit Message

Andreas Dannenberg June 4, 2019, 10:55 p.m. UTC 
Use the System Firmware (SYSFW) loader framework to load and start
the SYSFW as part of the AM654 early initialization sequence. While
at it also initialize the WKUP_UART0 pinmux as it is used by SYSFW
to print diagnostic messages.

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
---
 arch/arm/mach-k3/am6_init.c | 27 ++++++++++++++++++++++++++-
 board/ti/am65x/Kconfig      |  1 +
 2 files changed, 27 insertions(+), 1 deletion(-)

Comments

Tom Rini July 19, 2019, midnight UTC | #1 
On Tue, Jun 04, 2019 at 05:55:50PM -0500, Andreas Dannenberg wrote:

> Use the System Firmware (SYSFW) loader framework to load and start
> the SYSFW as part of the AM654 early initialization sequence. While
> at it also initialize the WKUP_UART0 pinmux as it is used by SYSFW
> to print diagnostic messages.
> 
> Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>

Applied to u-boot/master, thanks!
diff mbox series

Patch

diff --git a/arch/arm/mach-k3/am6_init.c b/arch/arm/mach-k3/am6_init.c
index 60a580305d..e326f575e5 100644
--- a/arch/arm/mach-k3/am6_init.c
+++ b/arch/arm/mach-k3/am6_init.c
@@ -10,8 +10,11 @@ 
 #include <asm/io.h>
 #include <spl.h>
 #include <asm/arch/hardware.h>
+#include <asm/arch/sysfw-loader.h>
 #include "common.h"
 #include <dm.h>
+#include <dm/uclass-internal.h>
+#include <dm/pinctrl.h>
 
 #ifdef CONFIG_SPL_BUILD
 static void mmr_unlock(u32 base, u32 partition)
@@ -63,7 +66,7 @@  static void store_boot_index_from_rom(void)
 
 void board_init_f(ulong dummy)
 {
-#if defined(CONFIG_K3_AM654_DDRSS)
+#if defined(CONFIG_K3_LOAD_SYSFW) || defined(CONFIG_K3_AM654_DDRSS)
 	struct udevice *dev;
 	int ret;
 #endif
@@ -83,8 +86,30 @@  void board_init_f(ulong dummy)
 	/* Init DM early in-order to invoke system controller */
 	spl_early_init();
 
+#ifdef CONFIG_K3_LOAD_SYSFW
+	/*
+	 * Process pinctrl for the serial0 a.k.a. WKUP_UART0 module and continue
+	 * regardless of the result of pinctrl. Do this without probing the
+	 * device, but instead by searching the device that would request the
+	 * given sequence number if probed. The UART will be used by the system
+	 * firmware (SYSFW) image for various purposes and SYSFW depends on us
+	 * to initialize its pin settings.
+	 */
+	ret = uclass_find_device_by_seq(UCLASS_SERIAL, 0, true, &dev);
+	if (!ret)
+		pinctrl_select_state(dev, "default");
+
+	/*
+	 * Load, start up, and configure system controller firmware. Provide
+	 * the U-Boot console init function to the SYSFW post-PM configuration
+	 * callback hook, effectively switching on (or over) the console
+	 * output.
+	 */
+	k3_sysfw_loader(preloader_console_init);
+#else
 	/* Prepare console output */
 	preloader_console_init();
+#endif
 
 #ifdef CONFIG_K3_AM654_DDRSS
 	ret = uclass_get_device(UCLASS_RAM, 0, &dev);
diff --git a/board/ti/am65x/Kconfig b/board/ti/am65x/Kconfig
index 98172c28f5..60bb834aca 100644
--- a/board/ti/am65x/Kconfig
+++ b/board/ti/am65x/Kconfig
@@ -18,6 +18,7 @@  config TARGET_AM654_R5_EVM
 	select CPU_V7R
 	select SYS_THUMB_BUILD
 	select SOC_K3_AM6
+	select K3_LOAD_SYSFW
 	select K3_AM654_DDRSS
 	imply SYS_K3_SPL_ATF