diff --git a/arch/arm/dts/sun5i-a10s-auxtek-t003.dts b/arch/arm/dts/sun5i-a10s-auxtek-t003.dts
index d4ad021823..39504d720e 100644
--- a/arch/arm/dts/sun5i-a10s-auxtek-t003.dts
+++ b/arch/arm/dts/sun5i-a10s-auxtek-t003.dts
@@ -44,7 +44,6 @@
 #include "sun5i-a10s.dtsi"
 #include "sunxi-common-regulators.dtsi"
 #include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
 
 / {
 	model = "Auxtek t003 A10s hdmi tv-stick";
@@ -94,8 +93,7 @@
 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_t003>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
-	cd-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
-	cd-inverted;
+	cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */
 	status = "okay";
 };
 
@@ -109,17 +107,15 @@
 
 &pio {
 	mmc0_cd_pin_t003: mmc0_cd_pin@0 {
-		allwinner,pins = "PG1";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+		pins = "PG1";
+		function = "gpio_in";
+		bias-pull-up;
 	};
 
 	led_pins_t003: led_pins@0 {
-		allwinner,pins = "PB2";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_20_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PB2";
+		function = "gpio_out";
+		drive-strength = <20>;
 	};
 };
 
@@ -139,14 +135,6 @@
 	status = "okay";
 };
 
-&usb0_vbus_pin_a {
-	allwinner,pins = "PG13";
-};
-
-&usb1_vbus_pin_a {
-	allwinner,pins = "PB10";
-};
-
 &usb_otg {
 	dr_mode = "host";
 	status = "okay";
diff --git a/arch/arm/dts/sun5i-a10s-auxtek-t004.dts b/arch/arm/dts/sun5i-a10s-auxtek-t004.dts
index a790ec8adb..8d4fb93312 100644
--- a/arch/arm/dts/sun5i-a10s-auxtek-t004.dts
+++ b/arch/arm/dts/sun5i-a10s-auxtek-t004.dts
@@ -44,7 +44,6 @@
 #include "sun5i-a10s.dtsi"
 #include "sunxi-common-regulators.dtsi"
 #include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
 
 / {
 	model = "Auxtek t004 A10s hdmi tv-stick";
@@ -105,8 +104,7 @@
 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_t004>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
-	cd-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
-	cd-inverted;
+	cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */
 	status = "okay";
 };
 
@@ -124,26 +122,32 @@
 	status = "okay";
 };
 
+&otg_sram {
+	status = "okay";
+};
+
 &pio {
+	usb0_id_detect_pin: usb0_id_detect_pin@0 {
+		pins = "PG12";
+		function = "gpio_in";
+		bias-pull-up;
+	};
+
 	mmc0_cd_pin_t004: mmc0_cd_pin@0 {
-		allwinner,pins = "PG1";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+		pins = "PG1";
+		function = "gpio_in";
+		bias-pull-up;
 	};
 
 	mmc1_vcc_en_pin_t004: mmc1_vcc_en_pin@0 {
-		allwinner,pins = "PB18";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PB18";
+		function = "gpio_out";
 	};
 
 	led_pins_t004: led_pins@0 {
-		allwinner,pins = "PB2";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_20_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PB2";
+		function = "gpio_out";
+		drive-strength = <20>;
 	};
 };
 
@@ -158,11 +162,15 @@
 	status = "okay";
 };
 
-&usb1_vbus_pin_a {
-	allwinner,pins = "PG13";
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
 };
 
 &usbphy {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_id_detect_pin>;
+	usb0_id_det-gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
 	usb1_vbus-supply = <&reg_usb1_vbus>;
 	status = "okay";
 };
diff --git a/arch/arm/dts/sun5i-a10s-mk802.dts b/arch/arm/dts/sun5i-a10s-mk802.dts
index 23b0114eb4..dd7fd5c3d7 100644
--- a/arch/arm/dts/sun5i-a10s-mk802.dts
+++ b/arch/arm/dts/sun5i-a10s-mk802.dts
@@ -92,8 +92,7 @@
 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_mk802>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
-	cd-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
-	cd-inverted;
+	cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */
 	status = "okay";
 };
 
@@ -116,24 +115,19 @@
 
 &pio {
 	led_pins_mk802: led_pins@0 {
-		allwinner,pins = "PB2";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PB2";
+		function = "gpio_out";
 	};
 
 	mmc0_cd_pin_mk802: mmc0_cd_pin@0 {
-		allwinner,pins = "PG1";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+		pins = "PG1";
+		function = "gpio_in";
+		bias-pull-up;
 	};
 
 	usb1_vbus_pin_mk802: usb1_vbus_pin@0 {
-		allwinner,pins = "PB10";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PB10";
+		function = "gpio_out";
 	};
 };
 
@@ -150,7 +144,7 @@
 };
 
 &usb_otg {
-	dr_mode = "otg";
+	dr_mode = "peripheral";
 	status = "okay";
 };
 
diff --git a/arch/arm/dts/sun5i-a10s-olinuxino-micro.dts b/arch/arm/dts/sun5i-a10s-olinuxino-micro.dts
index aef91476f9..2c902ed2c8 100644
--- a/arch/arm/dts/sun5i-a10s-olinuxino-micro.dts
+++ b/arch/arm/dts/sun5i-a10s-olinuxino-micro.dts
@@ -48,7 +48,6 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
 
 / {
 	model = "Olimex A10s-Olinuxino Micro";
@@ -64,6 +63,17 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
@@ -77,13 +87,17 @@
 	};
 };
 
+&be0 {
+	status = "okay";
+};
+
 &ehci0 {
 	status = "okay";
 };
 
 &emac {
 	pinctrl-names = "default";
-	pinctrl-0 = <&emac_pins_a>;
+	pinctrl-0 = <&emac_pins_b>;
 	phy = <&phy1>;
 	status = "okay";
 };
@@ -92,6 +106,16 @@
 	status = "okay";
 };
 
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
 &i2c0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c0_pins_a>;
@@ -177,8 +201,7 @@
 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxino_micro>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
-	cd-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
-	cd-inverted;
+	cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */
 	status = "okay";
 };
 
@@ -187,8 +210,7 @@
 	pinctrl-0 = <&mmc1_pins_a>, <&mmc1_cd_pin_olinuxino_micro>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
-	cd-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
-	cd-inverted;
+	cd-gpios = <&pio 6 13 GPIO_ACTIVE_LOW>; /* PG13 */
 	status = "okay";
 };
 
@@ -202,38 +224,32 @@
 
 &pio {
 	mmc0_cd_pin_olinuxino_micro: mmc0_cd_pin@0 {
-		allwinner,pins = "PG1";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+		pins = "PG1";
+		function = "gpio_in";
+		bias-pull-up;
 	};
 
 	mmc1_cd_pin_olinuxino_micro: mmc1_cd_pin@0 {
-		allwinner,pins = "PG13";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+		pins = "PG13";
+		function = "gpio_in";
+		bias-pull-up;
 	};
 
 	led_pins_olinuxino: led_pins@0 {
-		allwinner,pins = "PE3";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_20_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PE3";
+		function = "gpio_out";
+		drive-strength = <20>;
 	};
 
 	usb1_vbus_pin_olinuxino_m: usb1_vbus_pin@0 {
-		allwinner,pins = "PB10";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PB10";
+		function = "gpio_out";
 	};
 
 	usb0_id_detect_pin: usb0_id_detect_pin@0 {
-		allwinner,pins = "PG12";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+		pins = "PG12";
+		function = "gpio_in";
+		bias-pull-up;
 	};
 };
 
@@ -250,8 +266,12 @@
 
 &spi2 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&spi2_pins_a>,
-		    <&spi2_cs0_pins_a>;
+	pinctrl-0 = <&spi2_pins_b>,
+		    <&spi2_cs0_pins_b>;
+	status = "okay";
+};
+
+&tcon0 {
 	status = "okay";
 };
 
@@ -263,7 +283,7 @@
 
 &uart2 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart2_pins_a>;
+	pinctrl-0 = <&uart2_pins_b>;
 	status = "okay";
 };
 
@@ -278,10 +298,6 @@
 	status = "okay";
 };
 
-&usb0_vbus_pin_a {
-	allwinner,pins = "PG11";
-};
-
 &usbphy {
 	pinctrl-names = "default";
 	pinctrl-0 = <&usb0_id_detect_pin>;
diff --git a/arch/arm/dts/sun5i-a10s-r7-tv-dongle.dts b/arch/arm/dts/sun5i-a10s-r7-tv-dongle.dts
index 3b057983c7..034853d1c0 100644
--- a/arch/arm/dts/sun5i-a10s-r7-tv-dongle.dts
+++ b/arch/arm/dts/sun5i-a10s-r7-tv-dongle.dts
@@ -45,7 +45,6 @@
 #include "sunxi-common-regulators.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
 
 / {
 	model = "R7 A10s hdmi tv-stick";
@@ -81,8 +80,7 @@
 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_r7>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
-	cd-gpios = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
-	cd-inverted;
+	cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */
 	status = "okay";
 };
 
@@ -101,24 +99,20 @@
 
 &pio {
 	mmc0_cd_pin_r7: mmc0_cd_pin@0 {
-		allwinner,pins = "PG1";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+		pins = "PG1";
+		function = "gpio_in";
+		bias-pull-up;
 	};
 
 	led_pins_r7: led_pins@0 {
-		allwinner,pins = "PB2";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_20_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PB2";
+		function = "gpio_out";
+		drive-strength = <20>;
 	};
 
 	usb1_vbus_pin_r7: usb1_vbus_pin@0 {
-		allwinner,pins = "PG13";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PG13";
+		function = "gpio_out";
 	};
 };
 
diff --git a/arch/arm/dts/sun5i-a10s-wobo-i5.dts b/arch/arm/dts/sun5i-a10s-wobo-i5.dts
index b5de75f4c7..3f68ef5d92 100644
--- a/arch/arm/dts/sun5i-a10s-wobo-i5.dts
+++ b/arch/arm/dts/sun5i-a10s-wobo-i5.dts
@@ -46,7 +46,6 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
 
 / {
 	model = "A10s-Wobo i5";
@@ -95,7 +94,7 @@
 
 &emac {
 	pinctrl-names = "default";
-	pinctrl-0 = <&emac_pins_b>;
+	pinctrl-0 = <&emac_pins_a>;
 	phy = <&phy1>;
 	status = "okay";
 };
@@ -131,8 +130,7 @@
 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_wobo_i5>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
-	cd-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
-	cd-inverted;
+	cd-gpios = <&pio 1 3 GPIO_ACTIVE_LOW>; /* PB3 */
 	status = "okay";
 };
 
@@ -146,24 +144,19 @@
 
 &pio {
 	led_pins_wobo_i5: led_pins@0 {
-		allwinner,pins = "PB2";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PB2";
+		function = "gpio_out";
 	};
 
 	mmc0_cd_pin_wobo_i5: mmc0_cd_pin@0 {
-		allwinner,pins = "PB3";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+		pins = "PB3";
+		function = "gpio_in";
+		bias-pull-up;
 	};
 
 	emac_power_pin_wobo: emac_power_pin@0 {
-		allwinner,pins = "PA02";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PA02";
+		function = "gpio_out";
 	};
 };
 
@@ -222,10 +215,6 @@
 	status = "okay";
 };
 
-&usb1_vbus_pin_a {
-	allwinner,pins = "PG12";
-};
-
 &usbphy {
 	usb1_vbus-supply = <&reg_usb1_vbus>;
 	status = "okay";
diff --git a/arch/arm/dts/sun5i-a10s.dtsi b/arch/arm/dts/sun5i-a10s.dtsi
index c41a2ba34d..316cb8b294 100644
--- a/arch/arm/dts/sun5i-a10s.dtsi
+++ b/arch/arm/dts/sun5i-a10s.dtsi
@@ -47,7 +47,6 @@
 #include "sun5i.dtsi"
 
 #include <dt-bindings/dma/sun4i-a10.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
 
 / {
 	interrupt-parent = <&intc>;
@@ -61,207 +60,118 @@
 		#size-cells = <1>;
 		ranges;
 
-		framebuffer@0 {
+		framebuffer@2 {
 			compatible = "allwinner,simple-framebuffer",
 				     "simple-framebuffer";
 			allwinner,pipeline = "de_be0-lcd0-hdmi";
-			clocks = <&pll3>, <&pll5 1>, <&ahb_gates 36>,
-				 <&ahb_gates 43>, <&ahb_gates 44>;
-			status = "disabled";
-		};
-
-		framebuffer@1 {
-			compatible = "allwinner,simple-framebuffer",
-				     "simple-framebuffer";
-			allwinner,pipeline = "de_be0-lcd0";
-			clocks = <&pll3>, <&pll5 1>, <&ahb_gates 36>,
-				 <&ahb_gates 44>;
+			clocks = <&ccu CLK_AHB_LCD>, <&ccu CLK_AHB_HDMI>,
+				 <&ccu CLK_AHB_DE_BE>, <&ccu CLK_DRAM_DE_BE>,
+				 <&ccu CLK_DE_BE>, <&ccu CLK_HDMI>;
 			status = "disabled";
 		};
+	};
 
-		framebuffer@2 {
-			compatible = "allwinner,simple-framebuffer",
-				     "simple-framebuffer";
-			allwinner,pipeline = "de_be0-lcd0-tve0";
-			clocks = <&pll3>, <&pll5 1>, <&ahb_gates 34>,
-				 <&ahb_gates 36>, <&ahb_gates 44>;
-			status = "disabled";
-		};
+	display-engine {
+		compatible = "allwinner,sun5i-a10s-display-engine";
+		allwinner,pipelines = <&fe0>;
 	};
 
-	clocks {
-		ahb_gates: clk@01c20060 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun5i-a10s-ahb-gates-clk";
-			reg = <0x01c20060 0x8>;
-			clocks = <&ahb>;
-			clock-indices = <0>, <1>,
-					<2>, <5>, <6>,
-					<7>, <8>, <9>,
-					<10>, <13>,
-					<14>, <17>, <18>,
-					<20>, <21>, <22>,
-					<26>, <28>, <32>,
-					<34>, <36>, <40>,
-					<43>, <44>,
-					<46>, <51>,
-					<52>;
-			clock-output-names = "ahb_usbotg", "ahb_ehci",
-					     "ahb_ohci", "ahb_ss", "ahb_dma",
-					     "ahb_bist", "ahb_mmc0", "ahb_mmc1",
-					     "ahb_mmc2", "ahb_nand",
-					     "ahb_sdram", "ahb_emac", "ahb_ts",
-					     "ahb_spi0", "ahb_spi1", "ahb_spi2",
-					     "ahb_gps", "ahb_stimer", "ahb_ve",
-					     "ahb_tve", "ahb_lcd", "ahb_csi",
-					     "ahb_hdmi", "ahb_de_be",
-					     "ahb_de_fe", "ahb_iep",
-					     "ahb_mali400";
-		};
+	soc@1c00000 {
+		hdmi: hdmi@1c16000 {
+			compatible = "allwinner,sun5i-a10s-hdmi";
+			reg = <0x01c16000 0x1000>;
+			interrupts = <58>;
+			clocks = <&ccu CLK_AHB_HDMI>, <&ccu CLK_HDMI>,
+				 <&ccu CLK_PLL_VIDEO0_2X>,
+				 <&ccu CLK_PLL_VIDEO1_2X>;
+			clock-names = "ahb", "mod", "pll-0", "pll-1";
+			dmas = <&dma SUN4I_DMA_NORMAL 16>,
+			       <&dma SUN4I_DMA_NORMAL 16>,
+			       <&dma SUN4I_DMA_DEDICATED 24>;
+			dma-names = "ddc-tx", "ddc-rx", "audio-tx";
+			status = "disabled";
 
-		apb0_gates: clk@01c20068 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun5i-a10s-apb0-gates-clk";
-			reg = <0x01c20068 0x4>;
-			clocks = <&apb0>;
-			clock-indices = <0>, <3>,
-					<5>, <6>,
-					<10>;
-			clock-output-names = "apb0_codec", "apb0_iis",
-					     "apb0_pio", "apb0_ir",
-					     "apb0_keypad";
-		};
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
 
-		apb1_gates: clk@01c2006c {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun5i-a10s-apb1-gates-clk";
-			reg = <0x01c2006c 0x4>;
-			clocks = <&apb1>;
-			clock-indices = <0>, <1>,
-					<2>, <16>,
-					<17>, <18>,
-					<19>;
-			clock-output-names = "apb1_i2c0", "apb1_i2c1",
-					     "apb1_i2c2", "apb1_uart0",
-					     "apb1_uart1", "apb1_uart2",
-					     "apb1_uart3";
-		};
-	};
+				hdmi_in: port@0 {
+					reg = <0>;
 
-	soc@01c00000 {
-		emac: ethernet@01c0b000 {
-			compatible = "allwinner,sun4i-a10-emac";
-			reg = <0x01c0b000 0x1000>;
-			interrupts = <55>;
-			clocks = <&ahb_gates 17>;
-			allwinner,sram = <&emac_sram 1>;
-			status = "disabled";
-		};
+					hdmi_in_tcon0: endpoint {
+						remote-endpoint = <&tcon0_out_hdmi>;
+					};
+				};
 
-		mdio: mdio@01c0b080 {
-			compatible = "allwinner,sun4i-a10-mdio";
-			reg = <0x01c0b080 0x14>;
-			status = "disabled";
-			#address-cells = <1>;
-			#size-cells = <0>;
+				hdmi_out: port@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+			};
 		};
 
-		pwm: pwm@01c20e00 {
+		pwm: pwm@1c20e00 {
 			compatible = "allwinner,sun5i-a10s-pwm";
 			reg = <0x01c20e00 0xc>;
-			clocks = <&osc24M>;
+			clocks = <&ccu CLK_HOSC>;
 			#pwm-cells = <3>;
 			status = "disabled";
 		};
-
-		uart0: serial@01c28000 {
-			compatible = "snps,dw-apb-uart";
-			reg = <0x01c28000 0x400>;
-			interrupts = <1>;
-			reg-shift = <2>;
-			reg-io-width = <4>;
-			clocks = <&apb1_gates 16>;
-			status = "disabled";
-		};
-
-		uart2: serial@01c28800 {
-			compatible = "snps,dw-apb-uart";
-			reg = <0x01c28800 0x400>;
-			interrupts = <3>;
-			reg-shift = <2>;
-			reg-io-width = <4>;
-			clocks = <&apb1_gates 18>;
-			status = "disabled";
-		};
 	};
 };
 
+&ccu {
+	compatible = "allwinner,sun5i-a10s-ccu";
+};
+
 &pio {
 	compatible = "allwinner,sun5i-a10s-pinctrl";
 
 	uart0_pins_a: uart0@0 {
-		allwinner,pins = "PB19", "PB20";
-		allwinner,function = "uart0";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PB19", "PB20";
+		function = "uart0";
 	};
 
-	uart2_pins_a: uart2@0 {
-		allwinner,pins = "PC18", "PC19";
-		allwinner,function = "uart2";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	uart2_pins_b: uart2@1 {
+		pins = "PC18", "PC19";
+		function = "uart2";
 	};
 
-	emac_pins_a: emac0@0 {
-		allwinner,pins = "PA0", "PA1", "PA2",
+	emac_pins_b: emac0@1 {
+		pins = "PA0", "PA1", "PA2",
 				"PA3", "PA4", "PA5", "PA6",
 				"PA7", "PA8", "PA9", "PA10",
 				"PA11", "PA12", "PA13", "PA14",
 				"PA15", "PA16";
-		allwinner,function = "emac";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
-
-	emac_pins_b: emac0@1 {
-		allwinner,pins = "PD6", "PD7", "PD10",
-				"PD11", "PD12", "PD13", "PD14",
-				"PD15", "PD18", "PD19", "PD20",
-				"PD21", "PD22", "PD23", "PD24",
-				"PD25", "PD26", "PD27";
-		allwinner,function = "emac";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		function = "emac";
 	};
 
 	mmc1_pins_a: mmc1@0 {
-		allwinner,pins = "PG3", "PG4", "PG5",
+		pins = "PG3", "PG4", "PG5",
 				 "PG6", "PG7", "PG8";
-		allwinner,function = "mmc1";
-		allwinner,drive = <SUN4I_PINCTRL_30_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		function = "mmc1";
+		drive-strength = <30>;
 	};
 
-	spi2_pins_a: spi2@0 {
-		allwinner,pins = "PB12", "PB13", "PB14";
-		allwinner,function = "spi2";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	spi2_pins_b: spi2@1 {
+		pins = "PB12", "PB13", "PB14";
+		function = "spi2";
 	};
 
-	spi2_cs0_pins_a: spi2_cs0@0 {
-		allwinner,pins = "PB11";
-		allwinner,function = "spi2";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	spi2_cs0_pins_b: spi2_cs0@1 {
+		pins = "PB11";
+		function = "spi2";
 	};
 };
 
 &sram_a {
-	emac_sram: sram-section@8000 {
-		compatible = "allwinner,sun4i-a10-sram-a3-a4";
-		reg = <0x8000 0x4000>;
-		status = "disabled";
+};
+
+&tcon0_out {
+	tcon0_out_hdmi: endpoint@2 {
+		reg = <2>;
+		remote-endpoint = <&hdmi_in_tcon0>;
+		allwinner,tcon-channel = <1>;
 	};
 };
diff --git a/arch/arm/dts/sun5i-a13-empire-electronix-d709.dts b/arch/arm/dts/sun5i-a13-empire-electronix-d709.dts
index 6efbba6d40..378214d831 100644
--- a/arch/arm/dts/sun5i-a13-empire-electronix-d709.dts
+++ b/arch/arm/dts/sun5i-a13-empire-electronix-d709.dts
@@ -46,7 +46,6 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
 #include <dt-bindings/pwm/pwm.h>
 
 / {
@@ -126,8 +125,7 @@
 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_d709>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
-	cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
-	cd-inverted;
+	cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
 	status = "okay";
 };
 
@@ -137,24 +135,21 @@
 
 &pio {
 	mmc0_cd_pin_d709: mmc0_cd_pin@0 {
-		allwinner,pins = "PG0";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+		pins = "PG0";
+		function = "gpio_in";
+		bias-pull-up;
 	};
 
 	usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
-		allwinner,pins = "PG1";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
+		pins = "PG1";
+		function = "gpio_in";
+		bias-pull-down;
 	};
 
 	usb0_id_detect_pin: usb0_id_detect_pin@0 {
-		allwinner,pins = "PG2";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+		pins = "PG2";
+		function = "gpio_in";
+		bias-pull-up;
 	};
 };
 
@@ -211,10 +206,6 @@
 	status = "okay";
 };
 
-&usb0_vbus_pin_a {
-	allwinner,pins = "PG12";
-};
-
 &usbphy {
 	pinctrl-names = "default";
 	pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
diff --git a/arch/arm/dts/sun5i-a13-hsg-h702.dts b/arch/arm/dts/sun5i-a13-hsg-h702.dts
index 3724b98806..7ee0c3f6d7 100644
--- a/arch/arm/dts/sun5i-a13-hsg-h702.dts
+++ b/arch/arm/dts/sun5i-a13-hsg-h702.dts
@@ -46,7 +46,6 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
 
 / {
 	model = "HSG H702";
@@ -121,8 +120,7 @@
 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_h702>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
-	cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
-	cd-inverted;
+	cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
 	status = "okay";
 };
 
@@ -136,24 +134,20 @@
 
 &pio {
 	mmc0_cd_pin_h702: mmc0_cd_pin@0 {
-		allwinner,pins = "PG0";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+		pins = "PG0";
+		function = "gpio_in";
+		bias-pull-up;
 	};
 
 	usb0_id_detect_pin: usb0_id_detect_pin@0 {
-		allwinner,pins = "PG2";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+		pins = "PG2";
+		function = "gpio_in";
+		bias-pull-up;
 	};
 
 	usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
-		allwinner,pins = "PG1";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PG1";
+		function = "gpio_in";
 	};
 };
 
@@ -191,7 +185,6 @@
 };
 
 &reg_usb0_vbus {
-	pinctrl-0 = <&usb0_vbus_pin_a>;
 	gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
 	status = "okay";
 };
@@ -207,10 +200,6 @@
 	status = "okay";
 };
 
-&usb0_vbus_pin_a {
-	allwinner,pins = "PG12";
-};
-
 &usbphy {
 	pinctrl-names = "default";
 	pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
diff --git a/arch/arm/dts/sun5i-a13-inet-98v-rev2.dts b/arch/arm/dts/sun5i-a13-inet-98v-rev2.dts
index 1b11ec95ae..439ae3b537 100644
--- a/arch/arm/dts/sun5i-a13-inet-98v-rev2.dts
+++ b/arch/arm/dts/sun5i-a13-inet-98v-rev2.dts
@@ -42,171 +42,9 @@
 
 /dts-v1/;
 #include "sun5i-a13.dtsi"
-#include "sunxi-common-regulators.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include "sun5i-reference-design-tablet.dtsi"
 
 / {
 	model = "INet-98V Rev 02";
 	compatible = "primux,inet98v-rev2", "allwinner,sun5i-a13";
-
-	aliases {
-		serial0 = &uart1;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-};
-
-&cpu0 {
-	cpu-supply = <&reg_dcdc2>;
-};
-
-&ehci0 {
-	status = "okay";
-};
-
-&i2c0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c0_pins_a>;
-	status = "okay";
-
-	axp209: pmic@34 {
-		reg = <0x34>;
-		interrupts = <0>;
-	};
-};
-
-#include "axp209.dtsi"
-
-&i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins_a>;
-	status = "okay";
-
-	pcf8563: rtc@51 {
-		compatible = "nxp,pcf8563";
-		reg = <0x51>;
-	};
-};
-
-&lradc {
-	vref-supply = <&reg_ldo2>;
-	status = "okay";
-
-	button@200 {
-		label = "Volume Up";
-		linux,code = <KEY_VOLUMEUP>;
-		channel = <0>;
-		voltage = <200000>;
-	};
-
-	button@400 {
-		label = "Volume Down";
-		linux,code = <KEY_VOLUMEDOWN>;
-		channel = <0>;
-		voltage = <400000>;
-	};
-};
-
-&mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_inet98fv2>;
-	vmmc-supply = <&reg_vcc3v3>;
-	bus-width = <4>;
-	cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
-	cd-inverted;
-	status = "okay";
-};
-
-&otg_sram {
-	status = "okay";
-};
-
-&pio {
-	mmc0_cd_pin_inet98fv2: mmc0_cd_pin@0 {
-		allwinner,pins = "PG0";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
-	};
-
-	usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
-		allwinner,pins = "PG1";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
-	};
-
-	usb0_id_detect_pin: usb0_id_detect_pin@0 {
-		allwinner,pins = "PG2";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
-	};
-};
-
-&reg_dcdc2 {
-	regulator-always-on;
-	regulator-min-microvolt = <1000000>;
-	regulator-max-microvolt = <1400000>;
-	regulator-name = "vdd-cpu";
-};
-
-&reg_dcdc3 {
-	regulator-always-on;
-	regulator-min-microvolt = <1250000>;
-	regulator-max-microvolt = <1250000>;
-	regulator-name = "vdd-int-pll";
-};
-
-&reg_ldo1 {
-	regulator-name = "vdd-rtc";
-};
-
-&reg_ldo2 {
-	regulator-always-on;
-	regulator-min-microvolt = <3000000>;
-	regulator-max-microvolt = <3000000>;
-	regulator-name = "avcc";
-};
-
-&reg_ldo3 {
-	regulator-min-microvolt = <3300000>;
-	regulator-max-microvolt = <3300000>;
-	regulator-name = "vcc-wifi";
-};
-
-&reg_usb0_vbus {
-	gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
-	status = "okay";
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart1_pins_b>;
-	status = "okay";
-};
-
-&usb_otg {
-	dr_mode = "otg";
-	status = "okay";
-};
-
-&usb0_vbus_pin_a {
-	allwinner,pins = "PG12";
-};
-
-&usbphy {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
-	usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
-	usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
-	usb0_vbus-supply = <&reg_usb0_vbus>;
-	usb1_vbus-supply = <&reg_ldo3>;
-	status = "okay";
 };
diff --git a/arch/arm/dts/sun5i-a13-olinuxino-micro.dts b/arch/arm/dts/sun5i-a13-olinuxino-micro.dts
index 081329e2b8..aa4b34fd91 100644
--- a/arch/arm/dts/sun5i-a13-olinuxino-micro.dts
+++ b/arch/arm/dts/sun5i-a13-olinuxino-micro.dts
@@ -46,7 +46,6 @@
 #include "sunxi-common-regulators.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
 
 / {
 	model = "Olimex A13-Olinuxino Micro";
@@ -100,8 +99,7 @@
 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxinom>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
-	cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
-	cd-inverted;
+	cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
 	status = "okay";
 };
 
@@ -115,45 +113,37 @@
 
 &pio {
 	mmc0_cd_pin_olinuxinom: mmc0_cd_pin@0 {
-		allwinner,pins = "PG0";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+		pins = "PG0";
+		function = "gpio_in";
+		bias-pull-up;
 	};
 
 	led_pins_olinuxinom: led_pins@0 {
-		allwinner,pins = "PG9";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_20_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PG9";
+		function = "gpio_out";
+		drive-strength = <20>;
 	};
 
 	usb0_id_detect_pin: usb0_id_detect_pin@0 {
-		allwinner,pins = "PG2";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+		pins = "PG2";
+		function = "gpio_in";
+		bias-pull-up;
 	};
 
 	usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
-		allwinner,pins = "PG1";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
+		pins = "PG1";
+		function = "gpio_in";
+		bias-pull-down;
 	};
 
 	usb0_vbus_pin_olinuxinom: usb0_vbus_pin@0 {
-		allwinner,pins = "PG12";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PG12";
+		function = "gpio_out";
 	};
 
 	usb1_vbus_pin_olinuxinom: usb1_vbus_pin@0 {
-		allwinner,pins = "PG11";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PG11";
+		function = "gpio_out";
 	};
 };
 
diff --git a/arch/arm/dts/sun5i-a13-olinuxino.dts b/arch/arm/dts/sun5i-a13-olinuxino.dts
index b3c234c65e..437ad913a3 100644
--- a/arch/arm/dts/sun5i-a13-olinuxino.dts
+++ b/arch/arm/dts/sun5i-a13-olinuxino.dts
@@ -48,7 +48,6 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
 
 / {
 	model = "Olimex A13-Olinuxino";
@@ -72,6 +71,51 @@
 			default-state = "on";
 		};
 	};
+
+	bridge {
+		compatible = "dumb-vga-dac";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				vga_bridge_in: endpoint {
+					remote-endpoint = <&tcon0_out_vga>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				vga_bridge_out: endpoint {
+					remote-endpoint = <&vga_con_in>;
+				};
+			};
+		};
+	};
+
+	vga {
+		compatible = "vga-connector";
+
+		port {
+			vga_con_in: endpoint {
+				remote-endpoint = <&vga_bridge_out>;
+			};
+		};
+	};
+};
+
+&be0 {
+	status = "okay";
+};
+
+&codec {
+	status = "okay";
 };
 
 &ehci0 {
@@ -150,8 +194,7 @@
 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxino>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
-	cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
-	cd-inverted;
+	cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
 	status = "okay";
 };
 
@@ -165,38 +208,32 @@
 
 &pio {
 	mmc0_cd_pin_olinuxino: mmc0_cd_pin@0 {
-		allwinner,pins = "PG0";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+		pins = "PG0";
+		function = "gpio_in";
+		bias-pull-up;
 	};
 
 	led_pins_olinuxino: led_pins@0 {
-		allwinner,pins = "PG9";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_20_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PG9";
+		function = "gpio_out";
+		drive-strength = <20>;
 	};
 
 	usb0_id_detect_pin: usb0_id_detect_pin@0 {
-		allwinner,pins = "PG2";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+		pins = "PG2";
+		function = "gpio_in";
+		bias-pull-up;
 	};
 
 	usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
-		allwinner,pins = "PG1";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
+		pins = "PG1";
+		function = "gpio_in";
+		bias-pull-down;
 	};
 
 	usb1_vbus_pin_olinuxino: usb1_vbus_pin@0 {
-		allwinner,pins = "PG11";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PG11";
+		function = "gpio_out";
 	};
 };
 
@@ -211,6 +248,19 @@
 	status = "okay";
 };
 
+&tcon0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcd_rgb666_pins>;
+	status = "okay";
+};
+
+&tcon0_out {
+	tcon0_out_vga: endpoint@0 {
+		reg = <0>;
+		remote-endpoint = <&vga_bridge_in>;
+	};
+};
+
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart1_pins_b>;
@@ -222,10 +272,6 @@
 	status = "okay";
 };
 
-&usb0_vbus_pin_a {
-	allwinner,pins = "PG12";
-};
-
 &usbphy {
 	pinctrl-names = "default";
 	pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
diff --git a/arch/arm/dts/sun5i-a13-utoo-p66.dts b/arch/arm/dts/sun5i-a13-utoo-p66.dts
index a8b0bcc045..bfdd38d6bf 100644
--- a/arch/arm/dts/sun5i-a13-utoo-p66.dts
+++ b/arch/arm/dts/sun5i-a13-utoo-p66.dts
@@ -80,23 +80,7 @@
 };
 
 &codec_pa_pin {
-	allwinner,pins = "PG3";
-};
-
-&i2c1 {
-	icn8318: touchscreen@40 {
-		compatible = "chipone,icn8318";
-		reg = <0x40>;
-		interrupt-parent = <&pio>;
-		interrupts = <6 9 IRQ_TYPE_EDGE_FALLING>; /* EINT9 (PG9) */
-		pinctrl-names = "default";
-		pinctrl-0 = <&ts_wake_pin_p66>;
-		wake-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
-		touchscreen-size-x = <800>;
-		touchscreen-size-y = <480>;
-		touchscreen-inverted-x;
-		touchscreen-swapped-x-y;
-	};
+	pins = "PG3";
 };
 
 &mmc2 {
@@ -116,30 +100,35 @@
 
 &pio {
 	i2c_lcd_pins: i2c_lcd_pin@0 {
-		allwinner,pins = "PG10", "PG12";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
-	};
-
-	ts_wake_pin_p66: ts_wake_pin@0 {
-		allwinner,pins = "PB3";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PG10", "PG12";
+		function = "gpio_out";
+		bias-pull-up;
 	};
-
 };
 
 &reg_usb0_vbus {
 	gpio = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
 };
 
+&touchscreen {
+	compatible = "chipone,icn8318";
+	reg = <0x40>;
+	/* The P66 uses a different EINT then the reference design */
+	interrupts = <6 9 IRQ_TYPE_EDGE_FALLING>; /* EINT9 (PG9) */
+	/* The icn8318 binding expects wake-gpios instead of power-gpios */
+	wake-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
+	touchscreen-size-x = <800>;
+	touchscreen-size-y = <480>;
+	touchscreen-inverted-x;
+	touchscreen-swapped-x-y;
+	status = "okay";
+};
+
 &uart1 {
 	/* The P66 uses the uart pins as gpios */
 	status = "disabled";
 };
 
 &usb0_vbus_pin_a {
-	allwinner,pins = "PB4";
+	pins = "PB4";
 };
diff --git a/arch/arm/dts/sun5i-a13.dtsi b/arch/arm/dts/sun5i-a13.dtsi
index e012890e0c..b1d8277655 100644
--- a/arch/arm/dts/sun5i-a13.dtsi
+++ b/arch/arm/dts/sun5i-a13.dtsi
@@ -46,27 +46,11 @@
 
 #include "sun5i.dtsi"
 
-#include <dt-bindings/pinctrl/sun4i-a10.h>
 #include <dt-bindings/thermal/thermal.h>
 
 / {
 	interrupt-parent = <&intc>;
 
-	chosen {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		framebuffer@0 {
-			compatible = "allwinner,simple-framebuffer",
-				     "simple-framebuffer";
-			allwinner,pipeline = "de_be0-lcd0";
-			clocks = <&ahb_gates 36>, <&ahb_gates 44>, <&de_be_clk>,
-				 <&tcon_ch0_clk>, <&dram_gates 26>;
-			status = "disabled";
-		};
-	};
-
 	thermal-zones {
 		cpu_thermal {
 			/* milliseconds */
@@ -84,7 +68,7 @@
 			trips {
 				cpu_alert0: cpu_alert0 {
 					/* milliCelsius */
-					temperature = <850000>;
+					temperature = <85000>;
 					hysteresis = <2000>;
 					type = "passive";
 				};
@@ -99,237 +83,27 @@
 		};
 	};
 
-	clocks {
-		ahb_gates: clk@01c20060 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun5i-a13-ahb-gates-clk";
-			reg = <0x01c20060 0x8>;
-			clocks = <&ahb>;
-			clock-indices = <0>, <1>,
-					<2>, <5>, <6>,
-					<7>, <8>, <9>,
-					<10>, <13>,
-					<14>, <20>,
-					<21>, <22>,
-					<28>, <32>, <34>,
-					<36>, <40>, <44>,
-					<46>, <51>,
-					<52>;
-			clock-output-names = "ahb_usbotg", "ahb_ehci",
-					     "ahb_ohci", "ahb_ss", "ahb_dma",
-					     "ahb_bist", "ahb_mmc0", "ahb_mmc1",
-					     "ahb_mmc2", "ahb_nand",
-					     "ahb_sdram", "ahb_spi0",
-					     "ahb_spi1", "ahb_spi2",
-					     "ahb_stimer", "ahb_ve", "ahb_tve",
-					     "ahb_lcd", "ahb_csi", "ahb_de_be",
-					     "ahb_de_fe", "ahb_iep",
-					     "ahb_mali400";
-		};
-
-		apb0_gates: clk@01c20068 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun5i-a13-apb0-gates-clk";
-			reg = <0x01c20068 0x4>;
-			clocks = <&apb0>;
-			clock-indices = <0>, <5>,
-					<6>;
-			clock-output-names = "apb0_codec", "apb0_pio",
-					     "apb0_ir";
-		};
-
-		apb1_gates: clk@01c2006c {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun5i-a13-apb1-gates-clk";
-			reg = <0x01c2006c 0x4>;
-			clocks = <&apb1>;
-			clock-indices = <0>, <1>,
-					<2>, <17>,
-					<19>;
-			clock-output-names = "apb1_i2c0", "apb1_i2c1",
-					     "apb1_i2c2", "apb1_uart1",
-					     "apb1_uart3";
-		};
-
-		dram_gates: clk@01c20100 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun5i-a13-dram-gates-clk",
-				     "allwinner,sun4i-a10-gates-clk";
-			reg = <0x01c20100 0x4>;
-			clocks = <&pll5 0>;
-			clock-indices = <0>,
-					<1>,
-					<25>,
-					<26>,
-					<29>,
-					<31>;
-			clock-output-names = "dram_ve",
-					     "dram_csi",
-					     "dram_de_fe",
-					     "dram_de_be",
-					     "dram_ace",
-					     "dram_iep";
-		};
-
-		de_be_clk: clk@01c20104 {
-			#clock-cells = <0>;
-			#reset-cells = <0>;
-			compatible = "allwinner,sun4i-a10-display-clk";
-			reg = <0x01c20104 0x4>;
-			clocks = <&pll3>, <&pll7>, <&pll5 1>;
-			clock-output-names = "de-be";
-		};
-
-		de_fe_clk: clk@01c2010c {
-			#clock-cells = <0>;
-			#reset-cells = <0>;
-			compatible = "allwinner,sun4i-a10-display-clk";
-			reg = <0x01c2010c 0x4>;
-			clocks = <&pll3>, <&pll7>, <&pll5 1>;
-			clock-output-names = "de-fe";
-		};
-
-		tcon_ch0_clk: clk@01c20118 {
-			#clock-cells = <0>;
-			#reset-cells = <1>;
-			compatible = "allwinner,sun4i-a10-tcon-ch0-clk";
-			reg = <0x01c20118 0x4>;
-			clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
-			clock-output-names = "tcon-ch0-sclk";
-		};
-
-		tcon_ch1_clk: clk@01c2012c {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-tcon-ch1-clk";
-			reg = <0x01c2012c 0x4>;
-			clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
-			clock-output-names = "tcon-ch1-sclk";
-		};
-	};
-
 	display-engine {
 		compatible = "allwinner,sun5i-a13-display-engine";
 		allwinner,pipelines = <&fe0>;
 	};
 
-	soc@01c00000 {
-		tcon0: lcd-controller@01c0c000 {
-			compatible = "allwinner,sun5i-a13-tcon";
-			reg = <0x01c0c000 0x1000>;
-			interrupts = <44>;
-			resets = <&tcon_ch0_clk 1>;
-			reset-names = "lcd";
-			clocks = <&ahb_gates 36>,
-				 <&tcon_ch0_clk>,
-				 <&tcon_ch1_clk>;
-			clock-names = "ahb",
-				      "tcon-ch0",
-				      "tcon-ch1";
-			clock-output-names = "tcon-pixel-clock";
-			status = "disabled";
-
-			ports {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				tcon0_in: port@0 {
-					#address-cells = <1>;
-					#size-cells = <0>;
-					reg = <0>;
-
-					tcon0_in_be0: endpoint@0 {
-						reg = <0>;
-						remote-endpoint = <&be0_out_tcon0>;
-					};
-				};
-
-				tcon0_out: port@1 {
-					#address-cells = <1>;
-					#size-cells = <0>;
-					reg = <1>;
-				};
-			};
-		};
-
-		pwm: pwm@01c20e00 {
+	soc@1c00000 {
+		pwm: pwm@1c20e00 {
 			compatible = "allwinner,sun5i-a13-pwm";
 			reg = <0x01c20e00 0xc>;
-			clocks = <&osc24M>;
+			clocks = <&ccu CLK_HOSC>;
 			#pwm-cells = <3>;
 			status = "disabled";
 		};
 
-		fe0: display-frontend@01e00000 {
-			compatible = "allwinner,sun5i-a13-display-frontend";
-			reg = <0x01e00000 0x20000>;
-			interrupts = <47>;
-			clocks = <&ahb_gates 46>, <&de_fe_clk>,
-				 <&dram_gates 25>;
-			clock-names = "ahb", "mod",
-				      "ram";
-			resets = <&de_fe_clk>;
-			status = "disabled";
-
-			ports {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				fe0_out: port@1 {
-					#address-cells = <1>;
-					#size-cells = <0>;
-					reg = <1>;
-
-					fe0_out_be0: endpoint@0 {
-						reg = <0>;
-						remote-endpoint = <&be0_in_fe0>;
-					};
-				};
-			};
-		};
-
-		be0: display-backend@01e60000 {
-			compatible = "allwinner,sun5i-a13-display-backend";
-			reg = <0x01e60000 0x10000>;
-			clocks = <&ahb_gates 44>, <&de_be_clk>,
-				 <&dram_gates 26>;
-			clock-names = "ahb", "mod",
-				      "ram";
-			resets = <&de_be_clk>;
-			status = "disabled";
-
-			assigned-clocks = <&de_be_clk>;
-			assigned-clock-rates = <300000000>;
-
-			ports {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				be0_in: port@0 {
-					#address-cells = <1>;
-					#size-cells = <0>;
-					reg = <0>;
-
-					be0_in_fe0: endpoint@0 {
-						reg = <0>;
-						remote-endpoint = <&fe0_out_be0>;
-					};
-				};
-
-				be0_out: port@1 {
-					#address-cells = <1>;
-					#size-cells = <0>;
-					reg = <1>;
-
-					be0_out_tcon0: endpoint@0 {
-						reg = <0>;
-						remote-endpoint = <&tcon0_in_be0>;
-					};
-				};
-			};
-		};
 	};
 };
 
+&ccu {
+	compatible = "allwinner,sun5i-a13-ccu";
+};
+
 &cpu0 {
 	clock-latency = <244144>; /* 8 32k periods */
 	operating-points = <
@@ -342,34 +116,8 @@
 		432000	1200000
 		>;
 	#cooling-cells = <2>;
-	cooling-min-level = <0>;
-	cooling-max-level = <5>;
 };
 
 &pio {
 	compatible = "allwinner,sun5i-a13-pinctrl";
-
-	lcd_rgb666_pins: lcd_rgb666@0 {
-		allwinner,pins = "PD2", "PD3", "PD4", "PD5", "PD6", "PD7",
-				 "PD10", "PD11", "PD12", "PD13", "PD14", "PD15",
-				 "PD18", "PD19", "PD20", "PD21", "PD22", "PD23",
-				 "PD24", "PD25", "PD26", "PD27";
-		allwinner,function = "lcd0";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
-
-	uart1_pins_a: uart1@0 {
-		allwinner,pins = "PE10", "PE11";
-		allwinner,function = "uart1";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
-
-	uart1_pins_b: uart1@1 {
-		allwinner,pins = "PG3", "PG4";
-		allwinner,function = "uart1";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
 };
diff --git a/arch/arm/dts/sun5i-gr8-chip-pro.dts b/arch/arm/dts/sun5i-gr8-chip-pro.dts
index 92a2dc6250..c55b11a4d3 100644
--- a/arch/arm/dts/sun5i-gr8-chip-pro.dts
+++ b/arch/arm/dts/sun5i-gr8-chip-pro.dts
@@ -159,23 +159,19 @@
 
 &pio {
 	usb0_id_pin_chip_pro: usb0-id-pin@0 {
-		allwinner,pins = "PG2";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PG2";
+		function = "gpio_in";
 	};
 
 	wifi_reg_on_pin_chip_pro: wifi-reg-on-pin@0 {
-		allwinner,pins = "PB10";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PB10";
+		function = "gpio_out";
 	};
 };
 
 &pwm {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pwm0_pins_a>, <&pwm1_pins>;
+	pinctrl-0 = <&pwm0_pins>, <&pwm1_pins>;
 	status = "disabled";
 };
 
@@ -224,7 +220,7 @@
 
 &uart1 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart1_pins_a>, <&uart1_cts_rts_pins_a>;
+	pinctrl-0 = <&uart1_pins_b>, <&uart1_cts_rts_pins_a>;
 	status = "okay";
 };
 
diff --git a/arch/arm/dts/sun5i-gr8.dtsi b/arch/arm/dts/sun5i-gr8.dtsi
index ea86d4d58d..ef0b7446a9 100644
--- a/arch/arm/dts/sun5i-gr8.dtsi
+++ b/arch/arm/dts/sun5i-gr8.dtsi
@@ -42,901 +42,33 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
-#include <dt-bindings/clock/sun4i-a10-pll2.h>
+#include "sun5i.dtsi"
+
+#include <dt-bindings/clock/sun5i-ccu.h>
 #include <dt-bindings/dma/sun4i-a10.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/reset/sun5i-ccu.h>
 
 / {
-	interrupt-parent = <&intc>;
-	#address-cells = <1>;
-	#size-cells = <1>;
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu0: cpu@0 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a8";
-			reg = <0x0>;
-			clocks = <&cpu>;
-		};
-	};
-
-	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		/*
-		 * This is a dummy clock, to be used as placeholder on
-		 * other mux clocks when a specific parent clock is not
-		 * yet implemented. It should be dropped when the driver
-		 * is complete.
-		 */
-		dummy: dummy {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <0>;
-		};
-
-		osc24M: clk@01c20050 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-osc-clk";
-			reg = <0x01c20050 0x4>;
-			clock-frequency = <24000000>;
-			clock-output-names = "osc24M";
-		};
-
-		osc3M: osc3M-clk {
-			compatible = "fixed-factor-clock";
-			#clock-cells = <0>;
-			clock-div = <8>;
-			clock-mult = <1>;
-			clocks = <&osc24M>;
-			clock-output-names = "osc3M";
-		};
-
-		osc32k: clk@0 {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <32768>;
-			clock-output-names = "osc32k";
-		};
-
-		pll1: clk@01c20000 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-pll1-clk";
-			reg = <0x01c20000 0x4>;
-			clocks = <&osc24M>;
-			clock-output-names = "pll1";
-		};
-
-		pll2: clk@01c20008 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun5i-a13-pll2-clk";
-			reg = <0x01c20008 0x8>;
-			clocks = <&osc24M>;
-			clock-output-names = "pll2-1x", "pll2-2x",
-					     "pll2-4x", "pll2-8x";
-		};
-
-		pll3: clk@01c20010 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-pll3-clk";
-			reg = <0x01c20010 0x4>;
-			clocks = <&osc3M>;
-			clock-output-names = "pll3";
-		};
-
-		pll3x2: pll3x2-clk {
-			compatible = "allwinner,sun4i-a10-pll3-2x-clk";
-			#clock-cells = <0>;
-			clock-div = <1>;
-			clock-mult = <2>;
-			clocks = <&pll3>;
-			clock-output-names = "pll3-2x";
-		};
-
-		pll4: clk@01c20018 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-pll1-clk";
-			reg = <0x01c20018 0x4>;
-			clocks = <&osc24M>;
-			clock-output-names = "pll4";
-		};
-
-		pll5: clk@01c20020 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun4i-a10-pll5-clk";
-			reg = <0x01c20020 0x4>;
-			clocks = <&osc24M>;
-			clock-output-names = "pll5_ddr", "pll5_other";
-		};
-
-		pll6: clk@01c20028 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun4i-a10-pll6-clk";
-			reg = <0x01c20028 0x4>;
-			clocks = <&osc24M>;
-			clock-output-names = "pll6_sata", "pll6_other", "pll6";
-		};
-
-		pll7: clk@01c20030 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-pll3-clk";
-			reg = <0x01c20030 0x4>;
-			clocks = <&osc3M>;
-			clock-output-names = "pll7";
-		};
-
-		pll7x2: pll7x2-clk {
-			compatible = "allwinner,sun4i-a10-pll3-2x-clk";
-			#clock-cells = <0>;
-			clock-div = <1>;
-			clock-mult = <2>;
-			clocks = <&pll7>;
-			clock-output-names = "pll7-2x";
-		};
-
-		/* dummy is 200M */
-		cpu: cpu@01c20054 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-cpu-clk";
-			reg = <0x01c20054 0x4>;
-			clocks = <&osc32k>, <&osc24M>, <&pll1>, <&dummy>;
-			clock-output-names = "cpu";
-		};
-
-		axi: axi@01c20054 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-axi-clk";
-			reg = <0x01c20054 0x4>;
-			clocks = <&cpu>;
-			clock-output-names = "axi";
-		};
-
-		ahb: ahb@01c20054 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun5i-a13-ahb-clk";
-			reg = <0x01c20054 0x4>;
-			clocks = <&axi>, <&cpu>, <&pll6 1>;
-			clock-output-names = "ahb";
-			/*
-			 * Use PLL6 as parent, instead of CPU/AXI
-			 * which has rate changes due to cpufreq
-			 */
-			assigned-clocks = <&ahb>;
-			assigned-clock-parents = <&pll6 1>;
-		};
-
-		apb0: apb0@01c20054 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-apb0-clk";
-			reg = <0x01c20054 0x4>;
-			clocks = <&ahb>;
-			clock-output-names = "apb0";
-		};
-
-		apb1: clk@01c20058 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-apb1-clk";
-			reg = <0x01c20058 0x4>;
-			clocks = <&osc24M>, <&pll6 1>, <&osc32k>;
-			clock-output-names = "apb1";
-		};
-
-		axi_gates: clk@01c2005c {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun4i-a10-gates-clk";
-			reg = <0x01c2005c 0x4>;
-			clocks = <&axi>;
-			clock-indices = <0>;
-			clock-output-names = "axi_dram";
-		};
-
-		ahb_gates: clk@01c20060 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun5i-a13-ahb-gates-clk";
-			reg = <0x01c20060 0x8>;
-			clocks = <&ahb>;
-			clock-indices = <0>, <1>,
-					<2>, <5>, <6>,
-					<7>, <8>, <9>,
-					<10>, <13>,
-					<14>, <17>, <20>,
-					<21>, <22>,
-					<28>, <32>, <34>,
-					<36>, <40>, <44>,
-					<46>, <51>,
-					<52>;
-			clock-output-names = "ahb_usbotg", "ahb_ehci",
-					     "ahb_ohci", "ahb_ss", "ahb_dma",
-					     "ahb_bist", "ahb_mmc0", "ahb_mmc1",
-					     "ahb_mmc2", "ahb_nand",
-					     "ahb_sdram", "ahb_emac", "ahb_spi0",
-					     "ahb_spi1", "ahb_spi2",
-					     "ahb_hstimer", "ahb_ve", "ahb_tve",
-					     "ahb_lcd", "ahb_csi", "ahb_de_be",
-					     "ahb_de_fe", "ahb_iep",
-					     "ahb_mali400";
-		};
-
-		apb0_gates: clk@01c20068 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun4i-a10-gates-clk";
-			reg = <0x01c20068 0x4>;
-			clocks = <&apb0>;
-			clock-indices = <0>, <3>,
-					<5>, <6>;
-			clock-output-names = "apb0_codec", "apb0_i2s0",
-					     "apb0_pio", "apb0_ir";
-		};
-
-		apb1_gates: clk@01c2006c {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun4i-a10-gates-clk";
-			reg = <0x01c2006c 0x4>;
-			clocks = <&apb1>;
-			clock-indices = <0>, <1>,
-					<2>, <17>,
-					<18>, <19>;
-			clock-output-names = "apb1_i2c0", "apb1_i2c1",
-					     "apb1_i2c2", "apb1_uart1",
-					     "apb1_uart2", "apb1_uart3";
-		};
-
-		nand_clk: clk@01c20080 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-mod0-clk";
-			reg = <0x01c20080 0x4>;
-			clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
-			clock-output-names = "nand";
-		};
-
-		ms_clk: clk@01c20084 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-mod0-clk";
-			reg = <0x01c20084 0x4>;
-			clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
-			clock-output-names = "ms";
-		};
-
-		mmc0_clk: clk@01c20088 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun4i-a10-mmc-clk";
-			reg = <0x01c20088 0x4>;
-			clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
-			clock-output-names = "mmc0",
-					     "mmc0_output",
-					     "mmc0_sample";
-		};
-
-		mmc1_clk: clk@01c2008c {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun4i-a10-mmc-clk";
-			reg = <0x01c2008c 0x4>;
-			clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
-			clock-output-names = "mmc1",
-					     "mmc1_output",
-					     "mmc1_sample";
-		};
-
-		mmc2_clk: clk@01c20090 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun4i-a10-mmc-clk";
-			reg = <0x01c20090 0x4>;
-			clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
-			clock-output-names = "mmc2",
-					     "mmc2_output",
-					     "mmc2_sample";
-		};
-
-		ts_clk: clk@01c20098 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-mod0-clk";
-			reg = <0x01c20098 0x4>;
-			clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
-			clock-output-names = "ts";
-		};
-
-		ss_clk: clk@01c2009c {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-mod0-clk";
-			reg = <0x01c2009c 0x4>;
-			clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
-			clock-output-names = "ss";
-		};
-
-		spi0_clk: clk@01c200a0 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-mod0-clk";
-			reg = <0x01c200a0 0x4>;
-			clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
-			clock-output-names = "spi0";
-		};
-
-		spi1_clk: clk@01c200a4 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-mod0-clk";
-			reg = <0x01c200a4 0x4>;
-			clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
-			clock-output-names = "spi1";
-		};
-
-		spi2_clk: clk@01c200a8 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-mod0-clk";
-			reg = <0x01c200a8 0x4>;
-			clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
-			clock-output-names = "spi2";
-		};
-
-		ir0_clk: clk@01c200b0 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-mod0-clk";
-			reg = <0x01c200b0 0x4>;
-			clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
-			clock-output-names = "ir0";
-		};
-
-		i2s0_clk: clk@01c200b8 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-mod1-clk";
-			reg = <0x01c200b8 0x4>;
-			clocks = <&pll2 SUN4I_A10_PLL2_8X>,
-				 <&pll2 SUN4I_A10_PLL2_4X>,
-				 <&pll2 SUN4I_A10_PLL2_2X>,
-				 <&pll2 SUN4I_A10_PLL2_1X>;
-			clock-output-names = "i2s0";
-		};
-
-		spdif_clk: clk@01c200c0 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-mod1-clk";
-			reg = <0x01c200c0 0x4>;
-			clocks = <&pll2 SUN4I_A10_PLL2_8X>,
-				 <&pll2 SUN4I_A10_PLL2_4X>,
-				 <&pll2 SUN4I_A10_PLL2_2X>,
-				 <&pll2 SUN4I_A10_PLL2_1X>;
-			clock-output-names = "spdif";
-		};
-
-		usb_clk: clk@01c200cc {
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-			compatible = "allwinner,sun5i-a13-usb-clk";
-			reg = <0x01c200cc 0x4>;
-			clocks = <&pll6 1>;
-			clock-output-names = "usb_ohci0", "usb_phy";
-		};
-
-		dram_gates: clk@01c20100 {
-			#clock-cells = <1>;
-			compatible = "nextthing,gr8-dram-gates-clk",
-				     "allwinner,sun4i-a10-gates-clk";
-			reg = <0x01c20100 0x4>;
-			clocks = <&pll5 0>;
-			clock-indices = <0>,
-					<1>,
-					<25>,
-					<26>,
-					<29>,
-					<31>;
-			clock-output-names = "dram_ve",
-					     "dram_csi",
-					     "dram_de_fe",
-					     "dram_de_be",
-					     "dram_ace",
-					     "dram_iep";
-		};
-
-		de_be_clk: clk@01c20104 {
-			#clock-cells = <0>;
-			#reset-cells = <0>;
-			compatible = "allwinner,sun4i-a10-display-clk";
-			reg = <0x01c20104 0x4>;
-			clocks = <&pll3>, <&pll7>, <&pll5 1>;
-			clock-output-names = "de-be";
-		};
-
-		de_fe_clk: clk@01c2010c {
-			#clock-cells = <0>;
-			#reset-cells = <0>;
-			compatible = "allwinner,sun4i-a10-display-clk";
-			reg = <0x01c2010c 0x4>;
-			clocks = <&pll3>, <&pll7>, <&pll5 1>;
-			clock-output-names = "de-fe";
-		};
-
-		tcon_ch0_clk: clk@01c20118 {
-			#clock-cells = <0>;
-			#reset-cells = <1>;
-			compatible = "allwinner,sun4i-a10-tcon-ch0-clk";
-			reg = <0x01c20118 0x4>;
-			clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
-			clock-output-names = "tcon-ch0-sclk";
-		};
-
-		tcon_ch1_clk: clk@01c2012c {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-tcon-ch1-clk";
-			reg = <0x01c2012c 0x4>;
-			clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
-			clock-output-names = "tcon-ch1-sclk";
-		};
-
-		codec_clk: clk@01c20140 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-codec-clk";
-			reg = <0x01c20140 0x4>;
-			clocks = <&pll2 SUN4I_A10_PLL2_1X>;
-			clock-output-names = "codec";
-		};
-
-		mbus_clk: clk@01c2015c {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun5i-a13-mbus-clk";
-			reg = <0x01c2015c 0x4>;
-			clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
-			clock-output-names = "mbus";
-		};
-	};
-
 	display-engine {
 		compatible = "allwinner,sun5i-a13-display-engine";
 		allwinner,pipelines = <&fe0>;
 	};
 
-	soc@01c00000 {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		sram-controller@01c00000 {
-			compatible = "allwinner,sun4i-a10-sram-controller";
-			reg = <0x01c00000 0x30>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-
-			sram_a: sram@00000000 {
-				compatible = "mmio-sram";
-				reg = <0x00000000 0xc000>;
-				#address-cells = <1>;
-				#size-cells = <1>;
-				ranges = <0 0x00000000 0xc000>;
-			};
-
-			sram_d: sram@00010000 {
-				compatible = "mmio-sram";
-				reg = <0x00010000 0x1000>;
-				#address-cells = <1>;
-				#size-cells = <1>;
-				ranges = <0 0x00010000 0x1000>;
-
-				otg_sram: sram-section@0000 {
-					compatible = "allwinner,sun4i-a10-sram-d";
-					reg = <0x0000 0x1000>;
-					status = "disabled";
-				};
-			};
-		};
-
-		dma: dma-controller@01c02000 {
-			compatible = "allwinner,sun4i-a10-dma";
-			reg = <0x01c02000 0x1000>;
-			interrupts = <27>;
-			clocks = <&ahb_gates 6>;
-			#dma-cells = <2>;
-		};
-
-		nfc: nand@01c03000 {
-			compatible = "allwinner,sun4i-a10-nand";
-			reg = <0x01c03000 0x1000>;
-			interrupts = <37>;
-			clocks = <&ahb_gates 13>, <&nand_clk>;
-			clock-names = "ahb", "mod";
-			dmas = <&dma SUN4I_DMA_DEDICATED 3>;
-			dma-names = "rxtx";
-			status = "disabled";
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		spi0: spi@01c05000 {
-			compatible = "allwinner,sun4i-a10-spi";
-			reg = <0x01c05000 0x1000>;
-			interrupts = <10>;
-			clocks = <&ahb_gates 20>, <&spi0_clk>;
-			clock-names = "ahb", "mod";
-			dmas = <&dma SUN4I_DMA_DEDICATED 27>,
-			       <&dma SUN4I_DMA_DEDICATED 26>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		spi1: spi@01c06000 {
-			compatible = "allwinner,sun4i-a10-spi";
-			reg = <0x01c06000 0x1000>;
-			interrupts = <11>;
-			clocks = <&ahb_gates 21>, <&spi1_clk>;
-			clock-names = "ahb", "mod";
-			dmas = <&dma SUN4I_DMA_DEDICATED 9>,
-			       <&dma SUN4I_DMA_DEDICATED 8>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		tve0: tv-encoder@01c0a000 {
-			compatible = "allwinner,sun4i-a10-tv-encoder";
-			reg = <0x01c0a000 0x1000>;
-			clocks = <&ahb_gates 34>;
-			resets = <&tcon_ch0_clk 0>;
-			status = "disabled";
-
-			port {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				tve0_in_tcon0: endpoint@0 {
-					reg = <0>;
-					remote-endpoint = <&tcon0_out_tve0>;
-				};
-			};
-		};
-
-		tcon0: lcd-controller@01c0c000 {
-			compatible = "allwinner,sun5i-a13-tcon";
-			reg = <0x01c0c000 0x1000>;
-			interrupts = <44>;
-			resets = <&tcon_ch0_clk 1>;
-			reset-names = "lcd";
-			clocks = <&ahb_gates 36>,
-				 <&tcon_ch0_clk>,
-				 <&tcon_ch1_clk>;
-			clock-names = "ahb",
-				      "tcon-ch0",
-				      "tcon-ch1";
-			clock-output-names = "tcon-pixel-clock";
-			status = "disabled";
-
-			ports {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				tcon0_in: port@0 {
-					#address-cells = <1>;
-					#size-cells = <0>;
-					reg = <0>;
-
-					tcon0_in_be0: endpoint@0 {
-						reg = <0>;
-						remote-endpoint = <&be0_out_tcon0>;
-					};
-				};
-
-				tcon0_out: port@1 {
-					#address-cells = <1>;
-					#size-cells = <0>;
-					reg = <1>;
-
-					tcon0_out_tve0: endpoint@1 {
-						reg = <1>;
-						remote-endpoint = <&tve0_in_tcon0>;
-					};
-				};
-			};
-		};
-
-		mmc0: mmc@01c0f000 {
-			compatible = "allwinner,sun5i-a13-mmc";
-			reg = <0x01c0f000 0x1000>;
-			clocks = <&ahb_gates 8>,
-				 <&mmc0_clk 0>,
-				 <&mmc0_clk 1>,
-				 <&mmc0_clk 2>;
-			clock-names = "ahb",
-				      "mmc",
-				      "output",
-				      "sample";
-			interrupts = <32>;
-			status = "disabled";
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		mmc1: mmc@01c10000 {
-			compatible = "allwinner,sun5i-a13-mmc";
-			reg = <0x01c10000 0x1000>;
-			clocks = <&ahb_gates 9>,
-				 <&mmc1_clk 0>,
-				 <&mmc1_clk 1>,
-				 <&mmc1_clk 2>;
-			clock-names = "ahb",
-				      "mmc",
-				      "output",
-				      "sample";
-			interrupts = <33>;
-			status = "disabled";
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		mmc2: mmc@01c11000 {
-			compatible = "allwinner,sun5i-a13-mmc";
-			reg = <0x01c11000 0x1000>;
-			clocks = <&ahb_gates 10>,
-				 <&mmc2_clk 0>,
-				 <&mmc2_clk 1>,
-				 <&mmc2_clk 2>;
-			clock-names = "ahb",
-				      "mmc",
-				      "output",
-				      "sample";
-			interrupts = <34>;
-			status = "disabled";
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		usb_otg: usb@01c13000 {
-			compatible = "allwinner,sun4i-a10-musb";
-			reg = <0x01c13000 0x0400>;
-			clocks = <&ahb_gates 0>;
-			interrupts = <38>;
-			interrupt-names = "mc";
-			phys = <&usbphy 0>;
-			phy-names = "usb";
-			extcon = <&usbphy 0>;
-			allwinner,sram = <&otg_sram 1>;
-			status = "disabled";
-
-			dr_mode = "otg";
-		};
-
-		usbphy: phy@01c13400 {
-			#phy-cells = <1>;
-			compatible = "allwinner,sun5i-a13-usb-phy";
-			reg = <0x01c13400 0x10 0x01c14800 0x4>;
-			reg-names = "phy_ctrl", "pmu1";
-			clocks = <&usb_clk 8>;
-			clock-names = "usb_phy";
-			resets = <&usb_clk 0>, <&usb_clk 1>;
-			reset-names = "usb0_reset", "usb1_reset";
-			status = "disabled";
-		};
-
-		ehci0: usb@01c14000 {
-			compatible = "allwinner,sun5i-a13-ehci", "generic-ehci";
-			reg = <0x01c14000 0x100>;
-			interrupts = <39>;
-			clocks = <&ahb_gates 1>;
-			phys = <&usbphy 1>;
-			phy-names = "usb";
-			status = "disabled";
-		};
-
-		ohci0: usb@01c14400 {
-			compatible = "allwinner,sun5i-a13-ohci", "generic-ohci";
-			reg = <0x01c14400 0x100>;
-			interrupts = <40>;
-			clocks = <&usb_clk 6>, <&ahb_gates 2>;
-			phys = <&usbphy 1>;
-			phy-names = "usb";
-			status = "disabled";
-		};
-
-		spi2: spi@01c17000 {
-			compatible = "allwinner,sun4i-a10-spi";
-			reg = <0x01c17000 0x1000>;
-			interrupts = <12>;
-			clocks = <&ahb_gates 22>, <&spi2_clk>;
-			clock-names = "ahb", "mod";
-			dmas = <&dma SUN4I_DMA_DEDICATED 29>,
-			       <&dma SUN4I_DMA_DEDICATED 28>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		intc: interrupt-controller@01c20400 {
-			compatible = "allwinner,sun4i-a10-ic";
-			reg = <0x01c20400 0x400>;
-			interrupt-controller;
-			#interrupt-cells = <1>;
-		};
-
-		pio: pinctrl@01c20800 {
-			compatible = "nextthing,gr8-pinctrl";
-			reg = <0x01c20800 0x400>;
-			interrupts = <28>;
-			clocks = <&apb0_gates 5>;
-			gpio-controller;
-			interrupt-controller;
-			#interrupt-cells = <3>;
-			#gpio-cells = <3>;
-
-			i2c0_pins_a: i2c0@0 {
-				allwinner,pins = "PB0", "PB1";
-				allwinner,function = "i2c0";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-
-			i2c1_pins_a: i2c1@0 {
-				allwinner,pins = "PB15", "PB16";
-				allwinner,function = "i2c1";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-
-			i2c2_pins_a: i2c2@0 {
-				allwinner,pins = "PB17", "PB18";
-				allwinner,function = "i2c2";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-
-			i2s0_data_pins_a: i2s0-data@0 {
-				allwinner,pins = "PB6", "PB7", "PB8", "PB9";
-				allwinner,function = "i2s0";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-
-			i2s0_mclk_pins_a: i2s0-mclk@0 {
-				allwinner,pins = "PB5";
-				allwinner,function = "i2s0";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-
-			ir0_rx_pins_a: ir0@0 {
-				allwinner,pins = "PB4";
-				allwinner,function = "ir0";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-
-			lcd_rgb666_pins: lcd-rgb666@0 {
-				allwinner,pins = "PD2", "PD3", "PD4", "PD5", "PD6", "PD7",
-						 "PD10", "PD11", "PD12", "PD13", "PD14", "PD15",
-						 "PD18", "PD19", "PD20", "PD21", "PD22", "PD23",
-						 "PD24", "PD25", "PD26", "PD27";
-				allwinner,function = "lcd0";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-
-			mmc0_pins_a: mmc0@0 {
-				allwinner,pins = "PF0", "PF1", "PF2", "PF3",
-						 "PF4", "PF5";
-				allwinner,function = "mmc0";
-				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-
-			nand_pins_a: nand-base0@0 {
-				allwinner,pins = "PC0", "PC1", "PC2",
-						"PC5", "PC8", "PC9", "PC10",
-						"PC11", "PC12", "PC13", "PC14",
-						"PC15";
-				allwinner,function = "nand0";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-
-			nand_cs0_pins_a: nand-cs@0 {
-				allwinner,pins = "PC4";
-				allwinner,function = "nand0";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-
-			nand_rb0_pins_a: nand-rb@0 {
-				allwinner,pins = "PC6";
-				allwinner,function = "nand0";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-
-			pwm0_pins_a: pwm0@0 {
-				allwinner,pins = "PB2";
-				allwinner,function = "pwm0";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-
-			pwm1_pins: pwm1 {
-				allwinner,pins = "PG13";
-				allwinner,function = "pwm1";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-
-			spdif_tx_pins_a: spdif@0 {
-				allwinner,pins = "PB10";
-				allwinner,function = "spdif";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
-			};
-
-			uart1_pins_a: uart1@1 {
-				allwinner,pins = "PG3", "PG4";
-				allwinner,function = "uart1";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-
-			uart1_cts_rts_pins_a: uart1-cts-rts@0 {
-				allwinner,pins = "PG5", "PG6";
-				allwinner,function = "uart1";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-
-			uart2_pins_a: uart2@1 {
-				allwinner,pins = "PD2", "PD3";
-				allwinner,function = "uart2";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-
-			uart2_cts_rts_pins_a: uart2-cts-rts@0 {
-				allwinner,pins = "PD4", "PD5";
-				allwinner,function = "uart2";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-
-			uart3_pins_a: uart3@1 {
-				allwinner,pins = "PG9", "PG10";
-				allwinner,function = "uart3";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-
-			uart3_cts_rts_pins_a: uart3-cts-rts@0 {
-				allwinner,pins = "PG11", "PG12";
-				allwinner,function = "uart3";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-		};
-
-		pwm: pwm@01c20e00 {
+	soc@1c00000 {
+		pwm: pwm@1c20e00 {
 			compatible = "allwinner,sun5i-a10s-pwm";
 			reg = <0x01c20e00 0xc>;
-			clocks = <&osc24M>;
+			clocks = <&ccu CLK_HOSC>;
 			#pwm-cells = <3>;
 			status = "disabled";
 		};
 
-		timer@01c20c00 {
-			compatible = "allwinner,sun4i-a10-timer";
-			reg = <0x01c20c00 0x90>;
-			interrupts = <22>;
-			clocks = <&osc24M>;
-		};
-
-		wdt: watchdog@01c20c90 {
-			compatible = "allwinner,sun4i-a10-wdt";
-			reg = <0x01c20c90 0x10>;
-		};
-
-		spdif: spdif@01c21000 {
+		spdif: spdif@1c21000 {
 			#sound-dai-cells = <0>;
 			compatible = "allwinner,sun4i-a10-spdif";
 			reg = <0x01c21000 0x400>;
 			interrupts = <13>;
-			clocks = <&apb0_gates 1>, <&spdif_clk>;
+			clocks = <&ccu CLK_APB0_SPDIF>, <&ccu CLK_SPDIF>;
 			clock-names = "apb", "spdif";
 			dmas = <&dma SUN4I_DMA_NORMAL 2>,
 			       <&dma SUN4I_DMA_NORMAL 2>;
@@ -944,189 +76,51 @@
 			status = "disabled";
 		};
 
-		ir0: ir@01c21800 {
-			compatible = "allwinner,sun4i-a10-ir";
-			clocks = <&apb0_gates 6>, <&ir0_clk>;
-			clock-names = "apb", "ir";
-			interrupts = <5>;
-			reg = <0x01c21800 0x40>;
-			status = "disabled";
-		};
-
-		i2s0: i2s@01c22400 {
+		i2s0: i2s@1c22400 {
 			#sound-dai-cells = <0>;
 			compatible = "allwinner,sun4i-a10-i2s";
 			reg = <0x01c22400 0x400>;
 			interrupts = <16>;
-			clocks = <&apb0_gates 3>, <&i2s0_clk>;
+			clocks = <&ccu CLK_APB0_I2S>, <&ccu CLK_I2S>;
 			clock-names = "apb", "mod";
 			dmas = <&dma SUN4I_DMA_NORMAL 3>,
 			       <&dma SUN4I_DMA_NORMAL 3>;
 			dma-names = "rx", "tx";
 			status = "disabled";
 		};
+	};
+};
 
-		lradc: lradc@01c22800 {
-			compatible = "allwinner,sun4i-a10-lradc-keys";
-			reg = <0x01c22800 0x100>;
-			interrupts = <31>;
-			status = "disabled";
-		};
-
-		codec: codec@01c22c00 {
-			#sound-dai-cells = <0>;
-			compatible = "allwinner,sun4i-a10-codec";
-			reg = <0x01c22c00 0x40>;
-			interrupts = <30>;
-			clocks = <&apb0_gates 0>, <&codec_clk>;
-			clock-names = "apb", "codec";
-			dmas = <&dma SUN4I_DMA_NORMAL 19>,
-			       <&dma SUN4I_DMA_NORMAL 19>;
-			dma-names = "rx", "tx";
-			status = "disabled";
-		};
-
-		rtp: rtp@01c25000 {
-			compatible = "allwinner,sun5i-a13-ts";
-			reg = <0x01c25000 0x100>;
-			interrupts = <29>;
-			#thermal-sensor-cells = <0>;
-		};
-
-		uart1: serial@01c28400 {
-			compatible = "snps,dw-apb-uart";
-			reg = <0x01c28400 0x400>;
-			interrupts = <2>;
-			reg-shift = <2>;
-			reg-io-width = <4>;
-			clocks = <&apb1_gates 17>;
-			status = "disabled";
-		};
-
-		uart2: serial@01c28800 {
-			compatible = "snps,dw-apb-uart";
-			reg = <0x01c28800 0x400>;
-			interrupts = <3>;
-			reg-shift = <2>;
-			reg-io-width = <4>;
-			clocks = <&apb1_gates 18>;
-			status = "disabled";
-		};
-
-		uart3: serial@01c28c00 {
-			compatible = "snps,dw-apb-uart";
-			reg = <0x01c28c00 0x400>;
-			interrupts = <4>;
-			reg-shift = <2>;
-			reg-io-width = <4>;
-			clocks = <&apb1_gates 19>;
-			status = "disabled";
-		};
-
-		i2c0: i2c@01c2ac00 {
-			compatible = "allwinner,sun4i-a10-i2c";
-			reg = <0x01c2ac00 0x400>;
-			interrupts = <7>;
-			clocks = <&apb1_gates 0>;
-			status = "disabled";
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		i2c1: i2c@01c2b000 {
-			compatible = "allwinner,sun4i-a10-i2c";
-			reg = <0x01c2b000 0x400>;
-			interrupts = <8>;
-			clocks = <&apb1_gates 1>;
-			status = "disabled";
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		i2c2: i2c@01c2b400 {
-			compatible = "allwinner,sun4i-a10-i2c";
-			reg = <0x01c2b400 0x400>;
-			interrupts = <9>;
-			clocks = <&apb1_gates 2>;
-			status = "disabled";
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		timer@01c60000 {
-			compatible = "allwinner,sun5i-a13-hstimer";
-			reg = <0x01c60000 0x1000>;
-			interrupts = <82>, <83>;
-			clocks = <&ahb_gates 28>;
-		};
-
-		fe0: display-frontend@01e00000 {
-			compatible = "allwinner,sun5i-a13-display-frontend";
-			reg = <0x01e00000 0x20000>;
-			interrupts = <47>;
-			clocks = <&ahb_gates 46>, <&de_fe_clk>,
-				 <&dram_gates 25>;
-			clock-names = "ahb", "mod",
-				      "ram";
-			resets = <&de_fe_clk>;
-			status = "disabled";
-
-			ports {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				fe0_out: port@1 {
-					#address-cells = <1>;
-					#size-cells = <0>;
-					reg = <1>;
-
-					fe0_out_be0: endpoint@0 {
-						reg = <0>;
-						remote-endpoint = <&be0_in_fe0>;
-					};
-				};
-			};
-		};
-
-		be0: display-backend@01e60000 {
-			compatible = "allwinner,sun5i-a13-display-backend";
-			reg = <0x01e60000 0x10000>;
-			clocks = <&ahb_gates 44>, <&de_be_clk>,
-				 <&dram_gates 26>;
-			clock-names = "ahb", "mod",
-				      "ram";
-			resets = <&de_be_clk>;
-			status = "disabled";
+&ccu {
+	compatible = "nextthing,gr8-ccu";
+};
 
-			assigned-clocks = <&de_be_clk>;
-			assigned-clock-rates = <300000000>;
+&pio {
+	compatible = "nextthing,gr8-pinctrl";
 
-			ports {
-				#address-cells = <1>;
-				#size-cells = <0>;
+	i2s0_data_pins_a: i2s0-data@0 {
+		pins = "PB6", "PB7", "PB8", "PB9";
+		function = "i2s0";
+	};
 
-				be0_in: port@0 {
-					#address-cells = <1>;
-					#size-cells = <0>;
-					reg = <0>;
+	i2s0_mclk_pins_a: i2s0-mclk@0 {
+		pins = "PB5";
+		function = "i2s0";
+	};
 
-					be0_in_fe0: endpoint@0 {
-						reg = <0>;
-						remote-endpoint = <&fe0_out_be0>;
-					};
-				};
+	pwm1_pins: pwm1 {
+		pins = "PG13";
+		function = "pwm1";
+	};
 
-				be0_out: port@1 {
-					#address-cells = <1>;
-					#size-cells = <0>;
-					reg = <1>;
+	spdif_tx_pins_a: spdif@0 {
+		pins = "PB10";
+		function = "spdif";
+		bias-pull-up;
+	};
 
-					be0_out_tcon0: endpoint@0 {
-						reg = <0>;
-						remote-endpoint = <&tcon0_in_be0>;
-					};
-				};
-			};
-		};
+	uart1_cts_rts_pins_a: uart1-cts-rts@0 {
+		pins = "PG5", "PG6";
+		function = "uart1";
 	};
 };
diff --git a/arch/arm/dts/sun5i-r8-chip.dts b/arch/arm/dts/sun5i-r8-chip.dts
index 7a8cc27279..879a4b0f3b 100644
--- a/arch/arm/dts/sun5i-r8-chip.dts
+++ b/arch/arm/dts/sun5i-r8-chip.dts
@@ -56,25 +56,39 @@
 
 	aliases {
 		i2c0 = &i2c0;
+		i2c1 = &i2c1;
 		i2c2 = &i2c2;
 		serial0 = &uart1;
 		serial1 = &uart3;
+		spi0 = &spi2;
 	};
 
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
 
-	wifi_reg_on: wifi_reg_on {
-		compatible = "regulator-fixed";
+	leds {
+		compatible = "gpio-leds";
+
+		status {
+			label = "chip:white:status";
+			gpios = <&axp_gpio 2 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	mmc0_pwrseq: mmc0_pwrseq {
+		compatible = "mmc-pwrseq-simple";
 		pinctrl-names = "default";
 		pinctrl-0 = <&chip_wifi_reg_on_pin>;
+		reset-gpios = <&pio 2 19 GPIO_ACTIVE_LOW>; /* PC19 */
+	};
 
-		regulator-name = "wifi-reg-on";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		gpio = <&pio 2 19 GPIO_ACTIVE_HIGH>; /* PC19 */
-		enable-active-high;
+	onewire {
+		compatible = "w1-gpio";
+		gpios = <&pio 3 2 GPIO_ACTIVE_HIGH>; /* PD2 */
+		pinctrl-names = "default";
+		pinctrl-0 = <&chip_w1_pin>;
 	};
 };
 
@@ -114,6 +128,20 @@
 
 #include "axp209.dtsi"
 
+&ac_power_supply {
+	status = "okay";
+};
+
+&battery_power_supply {
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_a>;
+	status = "disabled";
+};
+
 &i2c2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c2_pins_a>;
@@ -134,13 +162,14 @@
 };
 
 &mmc0_pins_a {
-	allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+	bias-pull-up;
 };
 
 &mmc0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins_a>;
-	vmmc-supply = <&wifi_reg_on>;
+	vmmc-supply = <&reg_vcc3v3>;
+	mmc-pwrseq = <&mmc0_pwrseq>;
 	bus-width = <4>;
 	non-removable;
 	status = "okay";
@@ -156,24 +185,24 @@
 
 &pio {
 	chip_vbus_pin: chip_vbus_pin@0 {
-		allwinner,pins = "PB10";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PB10";
+		function = "gpio_out";
 	};
 
 	chip_wifi_reg_on_pin: chip_wifi_reg_on_pin@0 {
-		allwinner,pins = "PC19";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	        pins = "PC19";
+	        function = "gpio_out";
 	};
 
 	chip_id_det_pin: chip_id_det_pin@0 {
-		allwinner,pins = "PG2";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PG2";
+		function = "gpio_in";
+	};
+
+	chip_w1_pin: chip_w1_pin@0 {
+		pins = "PD2";
+		function = "gpio_in";
+	        bias-pull-up;
 	};
 };
 
@@ -202,17 +231,25 @@
 	regulator-always-on;
 };
 
+/*
+ * Both LDO3 and LDO4 are used in parallel to power up the WiFi/BT
+ * Chip.
+ *
+ * If those are not enabled, the SDIO part will not enumerate, and
+ * since there's no way currently to pass DT infos to an SDIO device,
+ * we cannot really do better than this ugly hack for now.
+ */
 &reg_ldo3 {
 	regulator-min-microvolt = <3300000>;
 	regulator-max-microvolt = <3300000>;
-	regulator-name = "vdd-wifi1";
+	regulator-name = "vcc-wifi-1";
 	regulator-always-on;
 };
 
 &reg_ldo4 {
 	regulator-min-microvolt = <3300000>;
 	regulator-max-microvolt = <3300000>;
-	regulator-name = "vdd-wifi2";
+	regulator-name = "vcc-wifi-2";
 	regulator-always-on;
 };
 
@@ -229,6 +266,12 @@
 	status = "okay";
 };
 
+&spi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "disabled";
+};
+
 &tcon0 {
 	status = "okay";
 };
@@ -246,7 +289,7 @@
 &uart3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart3_pins_a>,
-		    <&uart3_pins_cts_rts_a>;
+		    <&uart3_cts_rts_pins_a>;
 	status = "okay";
 };
 
diff --git a/arch/arm/dts/sun5i-r8.dtsi b/arch/arm/dts/sun5i-r8.dtsi
index 8b058f53b7..de35dbcd11 100644
--- a/arch/arm/dts/sun5i-r8.dtsi
+++ b/arch/arm/dts/sun5i-r8.dtsi
@@ -45,43 +45,3 @@
 
 #include "sun5i-a13.dtsi"
 
-/ {
-	chosen {
-		framebuffer@1 {
-			compatible = "allwinner,simple-framebuffer",
-				     "simple-framebuffer";
-			allwinner,pipeline = "de_be0-lcd0-tve0";
-			clocks = <&ahb_gates 34>, <&ahb_gates 36>,
-				 <&ahb_gates 44>, <&de_be_clk>,
-				 <&tcon_ch1_clk>, <&dram_gates 26>;
-			status = "disabled";
-		};
-	};
-
-	soc@01c00000 {
-		tve0: tv-encoder@01c0a000 {
-			compatible = "allwinner,sun4i-a10-tv-encoder";
-			reg = <0x01c0a000 0x1000>;
-			clocks = <&ahb_gates 34>;
-			resets = <&tcon_ch0_clk 0>;
-			status = "disabled";
-
-			port {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				tve0_in_tcon0: endpoint@0 {
-					reg = <0>;
-					remote-endpoint = <&tcon0_out_tve0>;
-				};
-			};
-		};
-	};
-};
-
-&tcon0_out {
-	tcon0_out_tve0: endpoint@1 {
-		reg = <1>;
-		remote-endpoint = <&tve0_in_tcon0>;
-	};
-};
diff --git a/arch/arm/dts/sun5i-reference-design-tablet.dtsi b/arch/arm/dts/sun5i-reference-design-tablet.dtsi
index 20cc940f5f..8acbaab14f 100644
--- a/arch/arm/dts/sun5i-reference-design-tablet.dtsi
+++ b/arch/arm/dts/sun5i-reference-design-tablet.dtsi
@@ -41,6 +41,7 @@
  */
 #include "sunxi-reference-design-tablet.dtsi"
 
+#include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/pwm/pwm.h>
 
 / {
@@ -84,6 +85,23 @@
 };
 
 &i2c1 {
+	/*
+	 * The gsl1680 is rated at 400KHz and it will not work reliable at
+	 * 100KHz, this has been confirmed on multiple different q8 tablets.
+	 * All other devices on this bus are also rated for 400KHz.
+	 */
+	clock-frequency = <400000>;
+
+	touchscreen: touchscreen {
+		interrupt-parent = <&pio>;
+		interrupts = <6 11 IRQ_TYPE_EDGE_FALLING>; /* EINT11 (PG11) */
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_power_pin>;
+		power-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
+		/* Tablet dts must provide reg and compatible */
+		status = "disabled";
+	};
+
 	pcf8563: rtc@51 {
 		compatible = "nxp,pcf8563";
 		reg = <0x51>;
@@ -92,6 +110,14 @@
 
 #include "axp209.dtsi"
 
+&ac_power_supply {
+	status = "okay";
+};
+
+&battery_power_supply {
+	status = "okay";
+};
+
 &lradc {
 	vref-supply = <&reg_ldo2>;
 };
@@ -101,8 +127,7 @@
 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
 	vmmc-supply = <&reg_vcc3v0>;
 	bus-width = <4>;
-	cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
-	cd-inverted;
+	cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
 	status = "okay";
 };
 
@@ -112,38 +137,38 @@
 
 &pio {
 	codec_pa_pin: codec_pa_pin@0 {
-		allwinner,pins = "PG10";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PG10";
+		function = "gpio_out";
 	};
 
 	mmc0_cd_pin: mmc0_cd_pin@0 {
-		allwinner,pins = "PG0";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+		pins = "PG0";
+		function = "gpio_in";
+		bias-pull-up;
+	};
+
+	ts_power_pin: ts_power_pin {
+		pins = "PB3";
+		function = "gpio_out";
+		drive-strength = <10>;
+		bias-disable;
 	};
 
 	usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
-		allwinner,pins = "PG1";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
+		pins = "PG1";
+		function = "gpio_in";
+		bias-pull-down;
 	};
 
 	usb0_id_detect_pin: usb0_id_detect_pin@0 {
-		allwinner,pins = "PG2";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+		pins = "PG2";
+		function = "gpio_in";
+		bias-pull-up;
 	};
 
 	usb0_vbus_pin_a: usb0_vbus_pin@0 {
-		allwinner,pins = "PG12";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+		pins = "PG12";
+		function = "gpio_out";
 	};
 };
 
diff --git a/arch/arm/dts/sun5i.dtsi b/arch/arm/dts/sun5i.dtsi
index e374f4fc80..07f2248ed5 100644
--- a/arch/arm/dts/sun5i.dtsi
+++ b/arch/arm/dts/sun5i.dtsi
@@ -44,9 +44,9 @@
 
 #include "skeleton.dtsi"
 
-#include <dt-bindings/clock/sun4i-a10-pll2.h>
+#include <dt-bindings/clock/sun5i-ccu.h>
 #include <dt-bindings/dma/sun4i-a10.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/reset/sun5i-ccu.h>
 
 / {
 	interrupt-parent = <&intc>;
@@ -59,42 +59,45 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a8";
 			reg = <0x0>;
-			clocks = <&cpu>;
+			clocks = <&ccu CLK_CPU>;
 		};
 	};
 
-	clocks {
+	chosen {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges;
 
-		/*
-		 * This is a dummy clock, to be used as placeholder on
-		 * other mux clocks when a specific parent clock is not
-		 * yet implemented. It should be dropped when the driver
-		 * is complete.
-		 */
-		dummy: dummy {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <0>;
+		framebuffer@0 {
+			compatible = "allwinner,simple-framebuffer",
+				     "simple-framebuffer";
+			allwinner,pipeline = "de_be0-lcd0";
+			clocks = <&ccu CLK_AHB_LCD>, <&ccu CLK_AHB_DE_BE>, <&ccu CLK_DE_BE>,
+				 <&ccu CLK_TCON_CH0>, <&ccu CLK_DRAM_DE_BE>;
+			status = "disabled";
 		};
 
-		osc24M: clk@01c20050 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-osc-clk";
-			reg = <0x01c20050 0x4>;
-			clock-frequency = <24000000>;
-			clock-output-names = "osc24M";
+		framebuffer@1 {
+			compatible = "allwinner,simple-framebuffer",
+				     "simple-framebuffer";
+			allwinner,pipeline = "de_be0-lcd0-tve0";
+			clocks = <&ccu CLK_AHB_TVE>, <&ccu CLK_AHB_LCD>,
+				 <&ccu CLK_AHB_DE_BE>, <&ccu CLK_DE_BE>,
+				 <&ccu CLK_TCON_CH1>, <&ccu CLK_DRAM_DE_BE>;
+			status = "disabled";
 		};
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
 
-		osc3M: osc3M_clk {
-			compatible = "fixed-factor-clock";
+		osc24M: clk@1c20050 {
 			#clock-cells = <0>;
-			clock-div = <8>;
-			clock-mult = <1>;
-			clocks = <&osc24M>;
-			clock-output-names = "osc3M";
+			compatible = "fixed-clock";
+			clock-frequency = <24000000>;
+			clock-output-names = "osc24M";
 		};
 
 		osc32k: clk@0 {
@@ -103,272 +106,22 @@
 			clock-frequency = <32768>;
 			clock-output-names = "osc32k";
 		};
-
-		pll1: clk@01c20000 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-pll1-clk";
-			reg = <0x01c20000 0x4>;
-			clocks = <&osc24M>;
-			clock-output-names = "pll1";
-		};
-
-		pll2: clk@01c20008 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun5i-a13-pll2-clk";
-			reg = <0x01c20008 0x8>;
-			clocks = <&osc24M>;
-			clock-output-names = "pll2-1x", "pll2-2x",
-					     "pll2-4x", "pll2-8x";
-		};
-
-		pll3: clk@01c20010 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-pll3-clk";
-			reg = <0x01c20010 0x4>;
-			clocks = <&osc3M>;
-			clock-output-names = "pll3";
-		};
-
-		pll3x2: pll3x2_clk {
-			compatible = "allwinner,sun4i-a10-pll3-2x-clk", "fixed-factor-clock";
-			#clock-cells = <0>;
-			clock-div = <1>;
-			clock-mult = <2>;
-			clocks = <&pll3>;
-			clock-output-names = "pll3-2x";
-		};
-
-		pll4: clk@01c20018 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-pll1-clk";
-			reg = <0x01c20018 0x4>;
-			clocks = <&osc24M>;
-			clock-output-names = "pll4";
-		};
-
-		pll5: clk@01c20020 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun4i-a10-pll5-clk";
-			reg = <0x01c20020 0x4>;
-			clocks = <&osc24M>;
-			clock-output-names = "pll5_ddr", "pll5_other";
-		};
-
-		pll6: clk@01c20028 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun4i-a10-pll6-clk";
-			reg = <0x01c20028 0x4>;
-			clocks = <&osc24M>;
-			clock-output-names = "pll6_sata", "pll6_other", "pll6";
-		};
-
-		pll7: clk@01c20030 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-pll3-clk";
-			reg = <0x01c20030 0x4>;
-			clocks = <&osc3M>;
-			clock-output-names = "pll7";
-		};
-
-		pll7x2: pll7x2_clk {
-			compatible = "fixed-factor-clock";
-			#clock-cells = <0>;
-			clock-div = <1>;
-			clock-mult = <2>;
-			clocks = <&pll7>;
-			clock-output-names = "pll7-2x";
-		};
-
-		/* dummy is 200M */
-		cpu: cpu@01c20054 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-cpu-clk";
-			reg = <0x01c20054 0x4>;
-			clocks = <&osc32k>, <&osc24M>, <&pll1>, <&dummy>;
-			clock-output-names = "cpu";
-		};
-
-		axi: axi@01c20054 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-axi-clk";
-			reg = <0x01c20054 0x4>;
-			clocks = <&cpu>;
-			clock-output-names = "axi";
-		};
-
-		ahb: ahb@01c20054 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun5i-a13-ahb-clk";
-			reg = <0x01c20054 0x4>;
-			clocks = <&axi>, <&cpu>, <&pll6 1>;
-			clock-output-names = "ahb";
-			/*
-			 * Use PLL6 as parent, instead of CPU/AXI
-			 * which has rate changes due to cpufreq
-			 */
-			assigned-clocks = <&ahb>;
-			assigned-clock-parents = <&pll6 1>;
-		};
-
-		apb0: apb0@01c20054 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-apb0-clk";
-			reg = <0x01c20054 0x4>;
-			clocks = <&ahb>;
-			clock-output-names = "apb0";
-		};
-
-		apb1: clk@01c20058 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-apb1-clk";
-			reg = <0x01c20058 0x4>;
-			clocks = <&osc24M>, <&pll6 1>, <&osc32k>;
-			clock-output-names = "apb1";
-		};
-
-		axi_gates: clk@01c2005c {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun4i-a10-axi-gates-clk";
-			reg = <0x01c2005c 0x4>;
-			clocks = <&axi>;
-			clock-indices = <0>;
-			clock-output-names = "axi_dram";
-		};
-
-		nand_clk: clk@01c20080 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-mod0-clk";
-			reg = <0x01c20080 0x4>;
-			clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
-			clock-output-names = "nand";
-		};
-
-		ms_clk: clk@01c20084 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-mod0-clk";
-			reg = <0x01c20084 0x4>;
-			clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
-			clock-output-names = "ms";
-		};
-
-		mmc0_clk: clk@01c20088 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun4i-a10-mmc-clk";
-			reg = <0x01c20088 0x4>;
-			clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
-			clock-output-names = "mmc0",
-					     "mmc0_output",
-					     "mmc0_sample";
-		};
-
-		mmc1_clk: clk@01c2008c {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun4i-a10-mmc-clk";
-			reg = <0x01c2008c 0x4>;
-			clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
-			clock-output-names = "mmc1",
-					     "mmc1_output",
-					     "mmc1_sample";
-		};
-
-		mmc2_clk: clk@01c20090 {
-			#clock-cells = <1>;
-			compatible = "allwinner,sun4i-a10-mmc-clk";
-			reg = <0x01c20090 0x4>;
-			clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
-			clock-output-names = "mmc2",
-					     "mmc2_output",
-					     "mmc2_sample";
-		};
-
-		ts_clk: clk@01c20098 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-mod0-clk";
-			reg = <0x01c20098 0x4>;
-			clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
-			clock-output-names = "ts";
-		};
-
-		ss_clk: clk@01c2009c {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-mod0-clk";
-			reg = <0x01c2009c 0x4>;
-			clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
-			clock-output-names = "ss";
-		};
-
-		spi0_clk: clk@01c200a0 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-mod0-clk";
-			reg = <0x01c200a0 0x4>;
-			clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
-			clock-output-names = "spi0";
-		};
-
-		spi1_clk: clk@01c200a4 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-mod0-clk";
-			reg = <0x01c200a4 0x4>;
-			clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
-			clock-output-names = "spi1";
-		};
-
-		spi2_clk: clk@01c200a8 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-mod0-clk";
-			reg = <0x01c200a8 0x4>;
-			clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
-			clock-output-names = "spi2";
-		};
-
-		ir0_clk: clk@01c200b0 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-mod0-clk";
-			reg = <0x01c200b0 0x4>;
-			clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
-			clock-output-names = "ir0";
-		};
-
-		usb_clk: clk@01c200cc {
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-			compatible = "allwinner,sun5i-a13-usb-clk";
-			reg = <0x01c200cc 0x4>;
-			clocks = <&pll6 1>;
-			clock-output-names = "usb_ohci0", "usb_phy";
-		};
-
-		codec_clk: clk@01c20140 {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun4i-a10-codec-clk";
-			reg = <0x01c20140 0x4>;
-			clocks = <&pll2 SUN4I_A10_PLL2_1X>;
-			clock-output-names = "codec";
-		};
-
-		mbus_clk: clk@01c2015c {
-			#clock-cells = <0>;
-			compatible = "allwinner,sun5i-a13-mbus-clk";
-			reg = <0x01c2015c 0x4>;
-			clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
-			clock-output-names = "mbus";
-		};
 	};
 
-	soc@01c00000 {
+	soc@1c00000 {
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges;
 
-		sram-controller@01c00000 {
+		sram-controller@1c00000 {
 			compatible = "allwinner,sun4i-a10-sram-controller";
 			reg = <0x01c00000 0x30>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
 
-			sram_a: sram@00000000 {
+			sram_a: sram@0 {
 				compatible = "mmio-sram";
 				reg = <0x00000000 0xc000>;
 				#address-cells = <1>;
@@ -376,14 +129,20 @@
 				ranges = <0 0x00000000 0xc000>;
 			};
 
-			sram_d: sram@00010000 {
+			emac_sram: sram-section@8000 {
+				compatible = "allwinner,sun4i-a10-sram-a3-a4";
+				reg = <0x8000 0x4000>;
+				status = "disabled";
+			};
+
+			sram_d: sram@10000 {
 				compatible = "mmio-sram";
 				reg = <0x00010000 0x1000>;
 				#address-cells = <1>;
 				#size-cells = <1>;
 				ranges = <0 0x00010000 0x1000>;
 
-				otg_sram: sram-section@0000 {
+				otg_sram: sram-section@0 {
 					compatible = "allwinner,sun4i-a10-sram-d";
 					reg = <0x0000 0x1000>;
 					status = "disabled";
@@ -391,19 +150,32 @@
 			};
 		};
 
-		dma: dma-controller@01c02000 {
+		dma: dma-controller@1c02000 {
 			compatible = "allwinner,sun4i-a10-dma";
 			reg = <0x01c02000 0x1000>;
 			interrupts = <27>;
-			clocks = <&ahb_gates 6>;
+			clocks = <&ccu CLK_AHB_DMA>;
 			#dma-cells = <2>;
 		};
 
-		spi0: spi@01c05000 {
+		nfc: nand@1c03000 {
+			compatible = "allwinner,sun4i-a10-nand";
+			reg = <0x01c03000 0x1000>;
+			interrupts = <37>;
+			clocks = <&ccu CLK_AHB_NAND>, <&ccu CLK_NAND>;
+			clock-names = "ahb", "mod";
+			dmas = <&dma SUN4I_DMA_DEDICATED 3>;
+			dma-names = "rxtx";
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		spi0: spi@1c05000 {
 			compatible = "allwinner,sun4i-a10-spi";
 			reg = <0x01c05000 0x1000>;
 			interrupts = <10>;
-			clocks = <&ahb_gates 20>, <&spi0_clk>;
+			clocks = <&ccu CLK_AHB_SPI0>, <&ccu CLK_SPI0>;
 			clock-names = "ahb", "mod";
 			dmas = <&dma SUN4I_DMA_DEDICATED 27>,
 			       <&dma SUN4I_DMA_DEDICATED 26>;
@@ -413,11 +185,11 @@
 			#size-cells = <0>;
 		};
 
-		spi1: spi@01c06000 {
+		spi1: spi@1c06000 {
 			compatible = "allwinner,sun4i-a10-spi";
 			reg = <0x01c06000 0x1000>;
 			interrupts = <11>;
-			clocks = <&ahb_gates 21>, <&spi1_clk>;
+			clocks = <&ccu CLK_AHB_SPI1>, <&ccu CLK_SPI1>;
 			clock-names = "ahb", "mod";
 			dmas = <&dma SUN4I_DMA_DEDICATED 9>,
 			       <&dma SUN4I_DMA_DEDICATED 8>;
@@ -427,61 +199,122 @@
 			#size-cells = <0>;
 		};
 
-		mmc0: mmc@01c0f000 {
+		tve0: tv-encoder@1c0a000 {
+			compatible = "allwinner,sun4i-a10-tv-encoder";
+			reg = <0x01c0a000 0x1000>;
+			clocks = <&ccu CLK_AHB_TVE>;
+			resets = <&ccu RST_TVE>;
+			status = "disabled";
+
+			port {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				tve0_in_tcon0: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&tcon0_out_tve0>;
+				};
+			};
+		};
+
+		emac: ethernet@1c0b000 {
+			compatible = "allwinner,sun4i-a10-emac";
+			reg = <0x01c0b000 0x1000>;
+			interrupts = <55>;
+			clocks = <&ccu CLK_AHB_EMAC>;
+			allwinner,sram = <&emac_sram 1>;
+			status = "disabled";
+		};
+
+		mdio: mdio@1c0b080 {
+			compatible = "allwinner,sun4i-a10-mdio";
+			reg = <0x01c0b080 0x14>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		tcon0: lcd-controller@1c0c000 {
+			compatible = "allwinner,sun5i-a13-tcon";
+			reg = <0x01c0c000 0x1000>;
+			interrupts = <44>;
+			resets = <&ccu RST_LCD>;
+			reset-names = "lcd";
+			clocks = <&ccu CLK_AHB_LCD>,
+				 <&ccu CLK_TCON_CH0>,
+				 <&ccu CLK_TCON_CH1>;
+			clock-names = "ahb",
+				      "tcon-ch0",
+				      "tcon-ch1";
+			clock-output-names = "tcon-pixel-clock";
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				tcon0_in: port@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+
+					tcon0_in_be0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&be0_out_tcon0>;
+					};
+				};
+
+				tcon0_out: port@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+
+					tcon0_out_tve0: endpoint@1 {
+						reg = <1>;
+						remote-endpoint = <&tve0_in_tcon0>;
+						allwinner,tcon-channel = <1>;
+					};
+				};
+			};
+		};
+
+		mmc0: mmc@1c0f000 {
 			compatible = "allwinner,sun5i-a13-mmc";
 			reg = <0x01c0f000 0x1000>;
-			clocks = <&ahb_gates 8>,
-				 <&mmc0_clk 0>,
-				 <&mmc0_clk 1>,
-				 <&mmc0_clk 2>;
-			clock-names = "ahb",
-				      "mmc",
-				      "output",
-				      "sample";
+			clocks = <&ccu CLK_AHB_MMC0>, <&ccu CLK_MMC0>;
+			clock-names = "ahb", "mmc";
 			interrupts = <32>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
 		};
 
-		mmc1: mmc@01c10000 {
+		mmc1: mmc@1c10000 {
 			compatible = "allwinner,sun5i-a13-mmc";
 			reg = <0x01c10000 0x1000>;
-			clocks = <&ahb_gates 9>,
-				 <&mmc1_clk 0>,
-				 <&mmc1_clk 1>,
-				 <&mmc1_clk 2>;
-			clock-names = "ahb",
-				      "mmc",
-				      "output",
-				      "sample";
+			clocks = <&ccu CLK_AHB_MMC1>, <&ccu CLK_MMC1>;
+			clock-names = "ahb", "mmc";
 			interrupts = <33>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
 		};
 
-		mmc2: mmc@01c11000 {
+		mmc2: mmc@1c11000 {
 			compatible = "allwinner,sun5i-a13-mmc";
 			reg = <0x01c11000 0x1000>;
-			clocks = <&ahb_gates 10>,
-				 <&mmc2_clk 0>,
-				 <&mmc2_clk 1>,
-				 <&mmc2_clk 2>;
-			clock-names = "ahb",
-				      "mmc",
-				      "output",
-				      "sample";
+			clocks = <&ccu CLK_AHB_MMC2>, <&ccu CLK_MMC2>;
+			clock-names = "ahb", "mmc";
 			interrupts = <34>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
 		};
 
-		usb_otg: usb@01c13000 {
+		usb_otg: usb@1c13000 {
 			compatible = "allwinner,sun4i-a10-musb";
 			reg = <0x01c13000 0x0400>;
-			clocks = <&ahb_gates 0>;
+			clocks = <&ccu CLK_AHB_OTG>;
 			interrupts = <38>;
 			interrupt-names = "mc";
 			phys = <&usbphy 0>;
@@ -491,43 +324,52 @@
 			status = "disabled";
 		};
 
-		usbphy: phy@01c13400 {
+		usbphy: phy@1c13400 {
 			#phy-cells = <1>;
 			compatible = "allwinner,sun5i-a13-usb-phy";
 			reg = <0x01c13400 0x10 0x01c14800 0x4>;
 			reg-names = "phy_ctrl", "pmu1";
-			clocks = <&usb_clk 8>;
+			clocks = <&ccu CLK_USB_PHY0>;
 			clock-names = "usb_phy";
-			resets = <&usb_clk 0>, <&usb_clk 1>;
+			resets = <&ccu RST_USB_PHY0>, <&ccu RST_USB_PHY1>;
 			reset-names = "usb0_reset", "usb1_reset";
 			status = "disabled";
 		};
 
-		ehci0: usb@01c14000 {
+		ehci0: usb@1c14000 {
 			compatible = "allwinner,sun5i-a13-ehci", "generic-ehci";
 			reg = <0x01c14000 0x100>;
 			interrupts = <39>;
-			clocks = <&ahb_gates 1>;
+			clocks = <&ccu CLK_AHB_EHCI>;
 			phys = <&usbphy 1>;
 			phy-names = "usb";
 			status = "disabled";
 		};
 
-		ohci0: usb@01c14400 {
+		ohci0: usb@1c14400 {
 			compatible = "allwinner,sun5i-a13-ohci", "generic-ohci";
 			reg = <0x01c14400 0x100>;
 			interrupts = <40>;
-			clocks = <&usb_clk 6>, <&ahb_gates 2>;
+			clocks = <&ccu CLK_USB_OHCI>, <&ccu CLK_AHB_OHCI>;
 			phys = <&usbphy 1>;
 			phy-names = "usb";
 			status = "disabled";
 		};
 
-		spi2: spi@01c17000 {
+		crypto: crypto-engine@1c15000 {
+			compatible = "allwinner,sun5i-a13-crypto",
+				     "allwinner,sun4i-a10-crypto";
+			reg = <0x01c15000 0x1000>;
+			interrupts = <54>;
+			clocks = <&ccu CLK_AHB_SS>, <&ccu CLK_SS>;
+			clock-names = "ahb", "mod";
+		};
+
+		spi2: spi@1c17000 {
 			compatible = "allwinner,sun4i-a10-spi";
 			reg = <0x01c17000 0x1000>;
 			interrupts = <12>;
-			clocks = <&ahb_gates 22>, <&spi2_clk>;
+			clocks = <&ccu CLK_AHB_SPI2>, <&ccu CLK_SPI2>;
 			clock-names = "ahb", "mod";
 			dmas = <&dma SUN4I_DMA_DEDICATED 29>,
 			       <&dma SUN4I_DMA_DEDICATED 28>;
@@ -537,107 +379,199 @@
 			#size-cells = <0>;
 		};
 
-		intc: interrupt-controller@01c20400 {
+		ccu: clock@1c20000 {
+			reg = <0x01c20000 0x400>;
+			clocks = <&osc24M>, <&osc32k>;
+			clock-names = "hosc", "losc";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		intc: interrupt-controller@1c20400 {
 			compatible = "allwinner,sun4i-a10-ic";
 			reg = <0x01c20400 0x400>;
 			interrupt-controller;
 			#interrupt-cells = <1>;
 		};
 
-		pio: pinctrl@01c20800 {
+		pio: pinctrl@1c20800 {
 			reg = <0x01c20800 0x400>;
 			interrupts = <28>;
-			clocks = <&apb0_gates 5>;
+			clocks = <&ccu CLK_APB0_PIO>, <&osc24M>, <&osc32k>;
+			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			interrupt-controller;
 			#interrupt-cells = <3>;
 			#gpio-cells = <3>;
 
+			emac_pins_a: emac0@0 {
+				pins = "PD6", "PD7", "PD10",
+				       "PD11", "PD12", "PD13", "PD14",
+				       "PD15", "PD18", "PD19", "PD20",
+				       "PD21", "PD22", "PD23", "PD24",
+				       "PD25", "PD26", "PD27";
+				function = "emac";
+			};
+
 			i2c0_pins_a: i2c0@0 {
-				allwinner,pins = "PB0", "PB1";
-				allwinner,function = "i2c0";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+				pins = "PB0", "PB1";
+				function = "i2c0";
 			};
 
 			i2c1_pins_a: i2c1@0 {
-				allwinner,pins = "PB15", "PB16";
-				allwinner,function = "i2c1";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+				pins = "PB15", "PB16";
+				function = "i2c1";
 			};
 
 			i2c2_pins_a: i2c2@0 {
-				allwinner,pins = "PB17", "PB18";
-				allwinner,function = "i2c2";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+				pins = "PB17", "PB18";
+				function = "i2c2";
+			};
+
+			ir0_rx_pins_a: ir0@0 {
+				pins = "PB4";
+				function = "ir0";
+			};
+
+			lcd_rgb565_pins: lcd_rgb565@0 {
+				pins = "PD3", "PD4", "PD5", "PD6", "PD7",
+						 "PD10", "PD11", "PD12", "PD13", "PD14", "PD15",
+						 "PD19", "PD20", "PD21", "PD22", "PD23",
+						 "PD24", "PD25", "PD26", "PD27";
+				function = "lcd0";
+			};
+
+			lcd_rgb666_pins: lcd_rgb666@0 {
+				pins = "PD2", "PD3", "PD4", "PD5", "PD6", "PD7",
+				       "PD10", "PD11", "PD12", "PD13", "PD14", "PD15",
+				       "PD18", "PD19", "PD20", "PD21", "PD22", "PD23",
+				       "PD24", "PD25", "PD26", "PD27";
+				function = "lcd0";
 			};
 
 			mmc0_pins_a: mmc0@0 {
-				allwinner,pins = "PF0", "PF1", "PF2", "PF3",
-						 "PF4", "PF5";
-				allwinner,function = "mmc0";
-				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+				pins = "PF0", "PF1", "PF2", "PF3",
+				       "PF4", "PF5";
+				function = "mmc0";
+				drive-strength = <30>;
+				bias-pull-up;
 			};
 
 			mmc2_pins_a: mmc2@0 {
-				allwinner,pins = "PC6", "PC7", "PC8", "PC9",
-					"PC10", "PC11", "PC12", "PC13",
-					"PC14", "PC15";
-				allwinner,function = "mmc2";
-				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+				pins = "PC6", "PC7", "PC8", "PC9",
+				       "PC10", "PC11", "PC12", "PC13",
+				       "PC14", "PC15";
+				function = "mmc2";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			mmc2_4bit_pins_a: mmc2-4bit@0 {
+				pins = "PC6", "PC7", "PC8", "PC9",
+				       "PC10", "PC11";
+				function = "mmc2";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			nand_pins_a: nand-base0@0 {
+				pins = "PC0", "PC1", "PC2",
+				       "PC5", "PC8", "PC9", "PC10",
+				       "PC11", "PC12", "PC13", "PC14",
+				       "PC15";
+				function = "nand0";
+			};
+
+			nand_cs0_pins_a: nand-cs@0 {
+				pins = "PC4";
+				function = "nand0";
+			};
+
+			nand_rb0_pins_a: nand-rb@0 {
+				pins = "PC6";
+				function = "nand0";
+			};
+
+			spi2_pins_a: spi2@0 {
+				pins = "PE1", "PE2", "PE3";
+				function = "spi2";
+			};
+
+			spi2_cs0_pins_a: spi2-cs0@0 {
+				pins = "PE0";
+				function = "spi2";
+			};
+
+			uart1_pins_a: uart1@0 {
+				pins = "PE10", "PE11";
+				function = "uart1";
+			};
+
+			uart1_pins_b: uart1@1 {
+				pins = "PG3", "PG4";
+				function = "uart1";
+			};
+
+			uart2_pins_a: uart2@0 {
+				pins = "PD2", "PD3";
+				function = "uart2";
+			};
+
+			uart2_cts_rts_pins_a: uart2-cts-rts@0 {
+				pins = "PD4", "PD5";
+				function = "uart2";
 			};
 
 			uart3_pins_a: uart3@0 {
-				allwinner,pins = "PG9", "PG10";
-				allwinner,function = "uart3";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+				pins = "PG9", "PG10";
+				function = "uart3";
 			};
 
-			uart3_pins_cts_rts_a: uart3-cts-rts@0 {
-				allwinner,pins = "PG11", "PG12";
-				allwinner,function = "uart3";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			uart3_cts_rts_pins_a: uart3-cts-rts@0 {
+				pins = "PG11", "PG12";
+				function = "uart3";
 			};
 
 			pwm0_pins: pwm0 {
-				allwinner,pins = "PB2";
-				allwinner,function = "pwm";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+				pins = "PB2";
+				function = "pwm";
 			};
 		};
 
-		timer@01c20c00 {
+		timer@1c20c00 {
 			compatible = "allwinner,sun4i-a10-timer";
 			reg = <0x01c20c00 0x90>;
 			interrupts = <22>;
-			clocks = <&osc24M>;
+			clocks = <&ccu CLK_HOSC>;
 		};
 
-		wdt: watchdog@01c20c90 {
+		wdt: watchdog@1c20c90 {
 			compatible = "allwinner,sun4i-a10-wdt";
 			reg = <0x01c20c90 0x10>;
 		};
 
-		lradc: lradc@01c22800 {
+		ir0: ir@1c21800 {
+			compatible = "allwinner,sun4i-a10-ir";
+			clocks = <&ccu CLK_APB0_IR>, <&ccu CLK_IR>;
+			clock-names = "apb", "ir";
+			interrupts = <5>;
+			reg = <0x01c21800 0x40>;
+			status = "disabled";
+		};
+
+		lradc: lradc@1c22800 {
 			compatible = "allwinner,sun4i-a10-lradc-keys";
 			reg = <0x01c22800 0x100>;
 			interrupts = <31>;
 			status = "disabled";
 		};
 
-		codec: codec@01c22c00 {
+		codec: codec@1c22c00 {
 			#sound-dai-cells = <0>;
 			compatible = "allwinner,sun4i-a10-codec";
 			reg = <0x01c22c00 0x40>;
 			interrupts = <30>;
-			clocks = <&apb0_gates 0>, <&codec_clk>;
+			clocks = <&ccu CLK_APB0_CODEC>, <&ccu CLK_CODEC>;
 			clock-names = "apb", "codec";
 			dmas = <&dma SUN4I_DMA_NORMAL 19>,
 			       <&dma SUN4I_DMA_NORMAL 19>;
@@ -645,73 +579,163 @@
 			status = "disabled";
 		};
 
-		sid: eeprom@01c23800 {
+		sid: eeprom@1c23800 {
 			compatible = "allwinner,sun4i-a10-sid";
 			reg = <0x01c23800 0x10>;
 		};
 
-		rtp: rtp@01c25000 {
+		rtp: rtp@1c25000 {
 			compatible = "allwinner,sun5i-a13-ts";
 			reg = <0x01c25000 0x100>;
 			interrupts = <29>;
 			#thermal-sensor-cells = <0>;
 		};
 
-		uart1: serial@01c28400 {
+		uart0: serial@1c28000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28000 0x400>;
+			interrupts = <1>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_APB1_UART0>;
+			status = "disabled";
+		};
+
+		uart1: serial@1c28400 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x01c28400 0x400>;
 			interrupts = <2>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
-			clocks = <&apb1_gates 17>;
+			clocks = <&ccu CLK_APB1_UART1>;
 			status = "disabled";
 		};
 
-		uart3: serial@01c28c00 {
+		uart2: serial@1c28800 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28800 0x400>;
+			interrupts = <3>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_APB1_UART2>;
+			status = "disabled";
+		};
+
+		uart3: serial@1c28c00 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x01c28c00 0x400>;
 			interrupts = <4>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
-			clocks = <&apb1_gates 19>;
+			clocks = <&ccu CLK_APB1_UART3>;
 			status = "disabled";
 		};
 
-		i2c0: i2c@01c2ac00 {
+		i2c0: i2c@1c2ac00 {
 			compatible = "allwinner,sun4i-a10-i2c";
 			reg = <0x01c2ac00 0x400>;
 			interrupts = <7>;
-			clocks = <&apb1_gates 0>;
+			clocks = <&ccu CLK_APB1_I2C0>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
 		};
 
-		i2c1: i2c@01c2b000 {
+		i2c1: i2c@1c2b000 {
 			compatible = "allwinner,sun4i-a10-i2c";
 			reg = <0x01c2b000 0x400>;
 			interrupts = <8>;
-			clocks = <&apb1_gates 1>;
+			clocks = <&ccu CLK_APB1_I2C1>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
 		};
 
-		i2c2: i2c@01c2b400 {
+		i2c2: i2c@1c2b400 {
 			compatible = "allwinner,sun4i-a10-i2c";
 			reg = <0x01c2b400 0x400>;
 			interrupts = <9>;
-			clocks = <&apb1_gates 2>;
+			clocks = <&ccu CLK_APB1_I2C2>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
 		};
 
-		timer@01c60000 {
+		timer@1c60000 {
 			compatible = "allwinner,sun5i-a13-hstimer";
 			reg = <0x01c60000 0x1000>;
 			interrupts = <82>, <83>;
-			clocks = <&ahb_gates 28>;
+			clocks = <&ccu CLK_AHB_HSTIMER>;
+		};
+
+		fe0: display-frontend@1e00000 {
+			compatible = "allwinner,sun5i-a13-display-frontend";
+			reg = <0x01e00000 0x20000>;
+			interrupts = <47>;
+			clocks = <&ccu CLK_DE_FE>, <&ccu CLK_DE_FE>,
+				 <&ccu CLK_DRAM_DE_FE>;
+			clock-names = "ahb", "mod",
+				      "ram";
+			resets = <&ccu RST_DE_FE>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fe0_out: port@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+
+					fe0_out_be0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&be0_in_fe0>;
+					};
+				};
+			};
+		};
+
+		be0: display-backend@1e60000 {
+			compatible = "allwinner,sun5i-a13-display-backend";
+			reg = <0x01e60000 0x10000>;
+			interrupts = <47>;
+			clocks = <&ccu CLK_AHB_DE_BE>, <&ccu CLK_DE_BE>,
+				 <&ccu CLK_DRAM_DE_BE>;
+			clock-names = "ahb", "mod",
+				      "ram";
+			resets = <&ccu RST_DE_BE>;
+			status = "disabled";
+
+			assigned-clocks = <&ccu CLK_DE_BE>;
+			assigned-clock-rates = <300000000>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				be0_in: port@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+
+					be0_in_fe0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&fe0_out_be0>;
+					};
+				};
+
+				be0_out: port@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+
+					be0_out_tcon0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&tcon0_in_be0>;
+					};
+				};
+			};
 		};
 	};
 };
diff --git a/include/dt-bindings/clock/sun5i-ccu.h b/include/dt-bindings/clock/sun5i-ccu.h
new file mode 100644
index 0000000000..81f34d477a
--- /dev/null
+++ b/include/dt-bindings/clock/sun5i-ccu.h
@@ -0,0 +1,106 @@
+/*
+ * Copyright 2016 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _DT_BINDINGS_CLK_SUN5I_H_
+#define _DT_BINDINGS_CLK_SUN5I_H_
+
+#define CLK_HOSC		1
+
+#define CLK_PLL_VIDEO0_2X	9
+
+#define CLK_PLL_VIDEO1_2X	16
+#define CLK_CPU			17
+
+#define CLK_AHB_OTG		23
+#define CLK_AHB_EHCI		24
+#define CLK_AHB_OHCI		25
+#define CLK_AHB_SS		26
+#define CLK_AHB_DMA		27
+#define CLK_AHB_BIST		28
+#define CLK_AHB_MMC0		29
+#define CLK_AHB_MMC1		30
+#define CLK_AHB_MMC2		31
+#define CLK_AHB_NAND		32
+#define CLK_AHB_SDRAM		33
+#define CLK_AHB_EMAC		34
+#define CLK_AHB_TS		35
+#define CLK_AHB_SPI0		36
+#define CLK_AHB_SPI1		37
+#define CLK_AHB_SPI2		38
+#define CLK_AHB_GPS		39
+#define CLK_AHB_HSTIMER		40
+#define CLK_AHB_VE		41
+#define CLK_AHB_TVE		42
+#define CLK_AHB_LCD		43
+#define CLK_AHB_CSI		44
+#define CLK_AHB_HDMI		45
+#define CLK_AHB_DE_BE		46
+#define CLK_AHB_DE_FE		47
+#define CLK_AHB_IEP		48
+#define CLK_AHB_GPU		49
+#define CLK_APB0_CODEC		50
+#define CLK_APB0_SPDIF		51
+#define CLK_APB0_I2S		52
+#define CLK_APB0_PIO		53
+#define CLK_APB0_IR		54
+#define CLK_APB0_KEYPAD		55
+#define CLK_APB1_I2C0		56
+#define CLK_APB1_I2C1		57
+#define CLK_APB1_I2C2		58
+#define CLK_APB1_UART0		59
+#define CLK_APB1_UART1		60
+#define CLK_APB1_UART2		61
+#define CLK_APB1_UART3		62
+#define CLK_NAND		63
+#define CLK_MMC0		64
+#define CLK_MMC1		65
+#define CLK_MMC2		66
+#define CLK_TS			67
+#define CLK_SS			68
+#define CLK_SPI0		69
+#define CLK_SPI1		70
+#define CLK_SPI2		71
+#define CLK_IR			72
+#define CLK_I2S			73
+#define CLK_SPDIF		74
+#define CLK_KEYPAD		75
+#define CLK_USB_OHCI		76
+#define CLK_USB_PHY0		77
+#define CLK_USB_PHY1		78
+#define CLK_GPS			79
+#define CLK_DRAM_VE		80
+#define CLK_DRAM_CSI		81
+#define CLK_DRAM_TS		82
+#define CLK_DRAM_TVE		83
+#define CLK_DRAM_DE_FE		84
+#define CLK_DRAM_DE_BE		85
+#define CLK_DRAM_ACE		86
+#define CLK_DRAM_IEP		87
+#define CLK_DE_BE		88
+#define CLK_DE_FE		89
+#define CLK_TCON_CH0		90
+
+#define CLK_TCON_CH1		92
+#define CLK_CSI			93
+#define CLK_VE			94
+#define CLK_CODEC		95
+#define CLK_AVS			96
+#define CLK_HDMI		97
+#define CLK_GPU			98
+
+#define CLK_IEP			100
+
+#endif /* _DT_BINDINGS_CLK_SUN5I_H_ */
diff --git a/include/dt-bindings/reset/sun5i-ccu.h b/include/dt-bindings/reset/sun5i-ccu.h
new file mode 100644
index 0000000000..c2b9726b50
--- /dev/null
+++ b/include/dt-bindings/reset/sun5i-ccu.h
@@ -0,0 +1,32 @@
+/*
+ * Copyright 2016 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _RST_SUN5I_H_
+#define _RST_SUN5I_H_
+
+#define RST_USB_PHY0	0
+#define RST_USB_PHY1	1
+#define RST_GPS		2
+#define RST_DE_BE	3
+#define RST_DE_FE	4
+#define RST_TVE		5
+#define RST_LCD		6
+#define RST_CSI		7
+#define RST_VE		8
+#define RST_GPU		9
+#define RST_IEP		10
+
+#endif /* _RST_SUN5I_H_ */
