Message ID | 1514991336-23951-1-git-send-email-fabio.estevam@nxp.com |
---|---|
State | Accepted |
Commit | db00e921fdc6af54492606dd0ebd1f0ab53c7a90 |
Delegated to: | Stefano Babic |
Headers | show |
Series | [U-Boot,1/3] mx6memcal: Fix the UART ports for mx6sabresd/auto boards | expand |
On 03/01/2018 15:55, Fabio Estevam wrote: > mx6sabresd board uses the following pins for console: > > PAD_CSI0_DAT10__UART1_TX_DATA > PAD_CSI0_DAT11__UART1_RX_DATA > > ,so put it in the same config option as wandboard. > > mx6sabreauto board uses the following pins for console: > > PAD_KEY_COL0__UART4_TX_DATA > PAD_KEY_ROW0__UART4_RX_DATA > > So do not mention sabreauto board as part of the UART1_SD3_DAT6_7 option. > > The config option for sabreauto can be added later when needed. > > Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> > --- > board/freescale/mx6memcal/Kconfig | 12 ++---------- > 1 file changed, 2 insertions(+), 10 deletions(-) > > diff --git a/board/freescale/mx6memcal/Kconfig b/board/freescale/mx6memcal/Kconfig > index 443804d..9987cba 100644 > --- a/board/freescale/mx6memcal/Kconfig > +++ b/board/freescale/mx6memcal/Kconfig > @@ -45,20 +45,12 @@ choice > NXP SABRELite. > > config UART1_CSI0_DAT10_11 > - bool "UART1 on CSI0_DAT10/11 (Wand)" > + bool "UART1 on CSI0_DAT10/11 (Wand, SabreSD)" > depends on SERIAL_CONSOLE_UART1 > help > Choose this configuration if you're using pads > CSI0_DAT10 and DAT11 for a console on UART1 as > - is done on the i.MX6 Wand board. > - > - config UART1_SD3_DAT6_7 > - bool "UART1 on SD3_DAT6/7 (SabreSD, SabreAuto)" > - depends on SERIAL_CONSOLE_UART1 > - help > - Choose this configuration if you're using pads > - SD3_DAT6 and DAT7 for a console on UART1 as is > - done on the NXP SABRESD or SABREAUTO designs. > + is done on the i.MX6 Wand board and i.MX6 SabreSD. > > config UART1_UART1 > bool "UART1 on UART1 (i.MX6SL EVK, WaRP)" > Applied to u-boot-imx, thanks ! Best regards, Stefano Babic
diff --git a/board/freescale/mx6memcal/Kconfig b/board/freescale/mx6memcal/Kconfig index 443804d..9987cba 100644 --- a/board/freescale/mx6memcal/Kconfig +++ b/board/freescale/mx6memcal/Kconfig @@ -45,20 +45,12 @@ choice NXP SABRELite. config UART1_CSI0_DAT10_11 - bool "UART1 on CSI0_DAT10/11 (Wand)" + bool "UART1 on CSI0_DAT10/11 (Wand, SabreSD)" depends on SERIAL_CONSOLE_UART1 help Choose this configuration if you're using pads CSI0_DAT10 and DAT11 for a console on UART1 as - is done on the i.MX6 Wand board. - - config UART1_SD3_DAT6_7 - bool "UART1 on SD3_DAT6/7 (SabreSD, SabreAuto)" - depends on SERIAL_CONSOLE_UART1 - help - Choose this configuration if you're using pads - SD3_DAT6 and DAT7 for a console on UART1 as is - done on the NXP SABRESD or SABREAUTO designs. + is done on the i.MX6 Wand board and i.MX6 SabreSD. config UART1_UART1 bool "UART1 on UART1 (i.MX6SL EVK, WaRP)"
mx6sabresd board uses the following pins for console: PAD_CSI0_DAT10__UART1_TX_DATA PAD_CSI0_DAT11__UART1_RX_DATA ,so put it in the same config option as wandboard. mx6sabreauto board uses the following pins for console: PAD_KEY_COL0__UART4_TX_DATA PAD_KEY_ROW0__UART4_RX_DATA So do not mention sabreauto board as part of the UART1_SD3_DAT6_7 option. The config option for sabreauto can be added later when needed. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> --- board/freescale/mx6memcal/Kconfig | 12 ++---------- 1 file changed, 2 insertions(+), 10 deletions(-)