diff --git a/arch/arm/mach-socfpga/Makefile b/arch/arm/mach-socfpga/Makefile
index 809cd47..b76de4c 100644
--- a/arch/arm/mach-socfpga/Makefile
+++ b/arch/arm/mach-socfpga/Makefile
@@ -13,7 +13,8 @@ obj-y	+= misc.o timer.o reset_manager.o system_manager.o clock_manager.o \
 obj-$(CONFIG_SPL_BUILD) += spl.o freeze_controller.o
 
 # QTS-generated config file wrappers
-obj-$(CONFIG_TARGET_SOCFPGA_GEN5)	+= scan_manager.o wrap_pll_config.o
+obj-$(CONFIG_TARGET_SOCFPGA_GEN5)	+= scan_manager.o wrap_pll_config.o \
+					   clock_manager_gen5.o
 obj-$(CONFIG_SPL_BUILD) += wrap_iocsr_config.o wrap_pinmux_config.o	\
 			   wrap_sdram_config.o
 CFLAGS_wrap_iocsr_config.o	+= -I$(srctree)/board/$(BOARDDIR)
diff --git a/arch/arm/mach-socfpga/clock_manager.c b/arch/arm/mach-socfpga/clock_manager.c
index 29e18f8..c2af6f3 100644
--- a/arch/arm/mach-socfpga/clock_manager.c
+++ b/arch/arm/mach-socfpga/clock_manager.c
@@ -1,5 +1,5 @@
 /*
- *  Copyright (C) 2013 Altera Corporation <www.altera.com>
+ *  Copyright (C) 2013-2017 Altera Corporation <www.altera.com>
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */
@@ -13,10 +13,10 @@ DECLARE_GLOBAL_DATA_PTR;
 static const struct socfpga_clock_manager *clock_manager_base =
 	(struct socfpga_clock_manager *)SOCFPGA_CLKMGR_ADDRESS;
 
-static void cm_wait_for_lock(uint32_t mask)
+void cm_wait_for_lock(u32 mask)
 {
-	register uint32_t inter_val;
-	uint32_t retry = 0;
+	u32 inter_val;
+	u32 retry = 0;
 	do {
 		inter_val = readl(&clock_manager_base->inter) & mask;
 		if (inter_val == mask)
@@ -29,512 +29,12 @@ static void cm_wait_for_lock(uint32_t mask)
 }
 
 /* function to poll in the fsm busy bit */
-static void cm_wait_for_fsm(void)
+void cm_wait_for_fsm(void)
 {
 	while (readl(&clock_manager_base->stat) & CLKMGR_STAT_BUSY)
 		;
 }
 
-/*
- * function to write the bypass register which requires a poll of the
- * busy bit
- */
-static void cm_write_bypass(uint32_t val)
-{
-	writel(val, &clock_manager_base->bypass);
-	cm_wait_for_fsm();
-}
-
-/* function to write the ctrl register which requires a poll of the busy bit */
-static void cm_write_ctrl(uint32_t val)
-{
-	writel(val, &clock_manager_base->ctrl);
-	cm_wait_for_fsm();
-}
-
-/* function to write a clock register that has phase information */
-static void cm_write_with_phase(uint32_t value,
-				uint32_t reg_address, uint32_t mask)
-{
-	/* poll until phase is zero */
-	while (readl(reg_address) & mask)
-		;
-
-	writel(value, reg_address);
-
-	while (readl(reg_address) & mask)
-		;
-}
-
-/*
- * Setup clocks while making no assumptions about previous state of the clocks.
- *
- * Start by being paranoid and gate all sw managed clocks
- * Put all plls in bypass
- * Put all plls VCO registers back to reset value (bandgap power down).
- * Put peripheral and main pll src to reset value to avoid glitch.
- * Delay 5 us.
- * Deassert bandgap power down and set numerator and denominator
- * Start 7 us timer.
- * set internal dividers
- * Wait for 7 us timer.
- * Enable plls
- * Set external dividers while plls are locking
- * Wait for pll lock
- * Assert/deassert outreset all.
- * Take all pll's out of bypass
- * Clear safe mode
- * set source main and peripheral clocks
- * Ungate clocks
- */
-
-void cm_basic_init(const struct cm_config * const cfg)
-{
-	unsigned long end;
-
-	/* Start by being paranoid and gate all sw managed clocks */
-
-	/*
-	 * We need to disable nandclk
-	 * and then do another apb access before disabling
-	 * gatting off the rest of the periperal clocks.
-	 */
-	writel(~CLKMGR_PERPLLGRP_EN_NANDCLK_MASK &
-		readl(&clock_manager_base->per_pll.en),
-		&clock_manager_base->per_pll.en);
-
-	/* DO NOT GATE OFF DEBUG CLOCKS & BRIDGE CLOCKS */
-	writel(CLKMGR_MAINPLLGRP_EN_DBGTIMERCLK_MASK |
-		CLKMGR_MAINPLLGRP_EN_DBGTRACECLK_MASK |
-		CLKMGR_MAINPLLGRP_EN_DBGCLK_MASK |
-		CLKMGR_MAINPLLGRP_EN_DBGATCLK_MASK |
-		CLKMGR_MAINPLLGRP_EN_S2FUSER0CLK_MASK |
-		CLKMGR_MAINPLLGRP_EN_L4MPCLK_MASK,
-		&clock_manager_base->main_pll.en);
-
-	writel(0, &clock_manager_base->sdr_pll.en);
-
-	/* now we can gate off the rest of the peripheral clocks */
-	writel(0, &clock_manager_base->per_pll.en);
-
-	/* Put all plls in bypass */
-	cm_write_bypass(CLKMGR_BYPASS_PERPLL | CLKMGR_BYPASS_SDRPLL |
-			CLKMGR_BYPASS_MAINPLL);
-
-	/* Put all plls VCO registers back to reset value. */
-	writel(CLKMGR_MAINPLLGRP_VCO_RESET_VALUE &
-	       ~CLKMGR_MAINPLLGRP_VCO_REGEXTSEL_MASK,
-	       &clock_manager_base->main_pll.vco);
-	writel(CLKMGR_PERPLLGRP_VCO_RESET_VALUE &
-	       ~CLKMGR_PERPLLGRP_VCO_REGEXTSEL_MASK,
-	       &clock_manager_base->per_pll.vco);
-	writel(CLKMGR_SDRPLLGRP_VCO_RESET_VALUE &
-	       ~CLKMGR_SDRPLLGRP_VCO_REGEXTSEL_MASK,
-	       &clock_manager_base->sdr_pll.vco);
-
-	/*
-	 * The clocks to the flash devices and the L4_MAIN clocks can
-	 * glitch when coming out of safe mode if their source values
-	 * are different from their reset value.  So the trick it to
-	 * put them back to their reset state, and change input
-	 * after exiting safe mode but before ungating the clocks.
-	 */
-	writel(CLKMGR_PERPLLGRP_SRC_RESET_VALUE,
-	       &clock_manager_base->per_pll.src);
-	writel(CLKMGR_MAINPLLGRP_L4SRC_RESET_VALUE,
-	       &clock_manager_base->main_pll.l4src);
-
-	/* read back for the required 5 us delay. */
-	readl(&clock_manager_base->main_pll.vco);
-	readl(&clock_manager_base->per_pll.vco);
-	readl(&clock_manager_base->sdr_pll.vco);
-
-
-	/*
-	 * We made sure bgpwr down was assert for 5 us. Now deassert BG PWR DN
-	 * with numerator and denominator.
-	 */
-	writel(cfg->main_vco_base, &clock_manager_base->main_pll.vco);
-	writel(cfg->peri_vco_base, &clock_manager_base->per_pll.vco);
-	writel(cfg->sdram_vco_base, &clock_manager_base->sdr_pll.vco);
-
-	/*
-	 * Time starts here. Must wait 7 us from
-	 * BGPWRDN_SET(0) to VCO_ENABLE_SET(1).
-	 */
-	end = timer_get_us() + 7;
-
-	/* main mpu */
-	writel(cfg->mpuclk, &clock_manager_base->main_pll.mpuclk);
-
-	/* altera group mpuclk */
-	writel(cfg->altera_grp_mpuclk, &clock_manager_base->altera.mpuclk);
-
-	/* main main clock */
-	writel(cfg->mainclk, &clock_manager_base->main_pll.mainclk);
-
-	/* main for dbg */
-	writel(cfg->dbgatclk, &clock_manager_base->main_pll.dbgatclk);
-
-	/* main for cfgs2fuser0clk */
-	writel(cfg->cfg2fuser0clk,
-	       &clock_manager_base->main_pll.cfgs2fuser0clk);
-
-	/* Peri emac0 50 MHz default to RMII */
-	writel(cfg->emac0clk, &clock_manager_base->per_pll.emac0clk);
-
-	/* Peri emac1 50 MHz default to RMII */
-	writel(cfg->emac1clk, &clock_manager_base->per_pll.emac1clk);
-
-	/* Peri QSPI */
-	writel(cfg->mainqspiclk, &clock_manager_base->main_pll.mainqspiclk);
-
-	writel(cfg->perqspiclk, &clock_manager_base->per_pll.perqspiclk);
-
-	/* Peri pernandsdmmcclk */
-	writel(cfg->mainnandsdmmcclk,
-	       &clock_manager_base->main_pll.mainnandsdmmcclk);
-
-	writel(cfg->pernandsdmmcclk,
-	       &clock_manager_base->per_pll.pernandsdmmcclk);
-
-	/* Peri perbaseclk */
-	writel(cfg->perbaseclk, &clock_manager_base->per_pll.perbaseclk);
-
-	/* Peri s2fuser1clk */
-	writel(cfg->s2fuser1clk, &clock_manager_base->per_pll.s2fuser1clk);
-
-	/* 7 us must have elapsed before we can enable the VCO */
-	while (timer_get_us() < end)
-		;
-
-	/* Enable vco */
-	/* main pll vco */
-	writel(cfg->main_vco_base | CLKMGR_MAINPLLGRP_VCO_EN,
-	       &clock_manager_base->main_pll.vco);
-
-	/* periferal pll */
-	writel(cfg->peri_vco_base | CLKMGR_MAINPLLGRP_VCO_EN,
-	       &clock_manager_base->per_pll.vco);
-
-	/* sdram pll vco */
-	writel(cfg->sdram_vco_base | CLKMGR_MAINPLLGRP_VCO_EN,
-	       &clock_manager_base->sdr_pll.vco);
-
-	/* L3 MP and L3 SP */
-	writel(cfg->maindiv, &clock_manager_base->main_pll.maindiv);
-
-	writel(cfg->dbgdiv, &clock_manager_base->main_pll.dbgdiv);
-
-	writel(cfg->tracediv, &clock_manager_base->main_pll.tracediv);
-
-	/* L4 MP, L4 SP, can0, and can1 */
-	writel(cfg->perdiv, &clock_manager_base->per_pll.div);
-
-	writel(cfg->gpiodiv, &clock_manager_base->per_pll.gpiodiv);
-
-#define LOCKED_MASK \
-	(CLKMGR_INTER_SDRPLLLOCKED_MASK  | \
-	CLKMGR_INTER_PERPLLLOCKED_MASK  | \
-	CLKMGR_INTER_MAINPLLLOCKED_MASK)
-
-	cm_wait_for_lock(LOCKED_MASK);
-
-	/* write the sdram clock counters before toggling outreset all */
-	writel(cfg->ddrdqsclk & CLKMGR_SDRPLLGRP_DDRDQSCLK_CNT_MASK,
-	       &clock_manager_base->sdr_pll.ddrdqsclk);
-
-	writel(cfg->ddr2xdqsclk & CLKMGR_SDRPLLGRP_DDR2XDQSCLK_CNT_MASK,
-	       &clock_manager_base->sdr_pll.ddr2xdqsclk);
-
-	writel(cfg->ddrdqclk & CLKMGR_SDRPLLGRP_DDRDQCLK_CNT_MASK,
-	       &clock_manager_base->sdr_pll.ddrdqclk);
-
-	writel(cfg->s2fuser2clk & CLKMGR_SDRPLLGRP_S2FUSER2CLK_CNT_MASK,
-	       &clock_manager_base->sdr_pll.s2fuser2clk);
-
-	/*
-	 * after locking, but before taking out of bypass
-	 * assert/deassert outresetall
-	 */
-	uint32_t mainvco = readl(&clock_manager_base->main_pll.vco);
-
-	/* assert main outresetall */
-	writel(mainvco | CLKMGR_MAINPLLGRP_VCO_OUTRESETALL_MASK,
-	       &clock_manager_base->main_pll.vco);
-
-	uint32_t periphvco = readl(&clock_manager_base->per_pll.vco);
-
-	/* assert pheriph outresetall */
-	writel(periphvco | CLKMGR_PERPLLGRP_VCO_OUTRESETALL_MASK,
-	       &clock_manager_base->per_pll.vco);
-
-	/* assert sdram outresetall */
-	writel(cfg->sdram_vco_base | CLKMGR_MAINPLLGRP_VCO_EN|
-		CLKMGR_SDRPLLGRP_VCO_OUTRESETALL,
-		&clock_manager_base->sdr_pll.vco);
-
-	/* deassert main outresetall */
-	writel(mainvco & ~CLKMGR_MAINPLLGRP_VCO_OUTRESETALL_MASK,
-	       &clock_manager_base->main_pll.vco);
-
-	/* deassert pheriph outresetall */
-	writel(periphvco & ~CLKMGR_PERPLLGRP_VCO_OUTRESETALL_MASK,
-	       &clock_manager_base->per_pll.vco);
-
-	/* deassert sdram outresetall */
-	writel(cfg->sdram_vco_base | CLKMGR_MAINPLLGRP_VCO_EN,
-	       &clock_manager_base->sdr_pll.vco);
-
-	/*
-	 * now that we've toggled outreset all, all the clocks
-	 * are aligned nicely; so we can change any phase.
-	 */
-	cm_write_with_phase(cfg->ddrdqsclk,
-			    (uint32_t)&clock_manager_base->sdr_pll.ddrdqsclk,
-			    CLKMGR_SDRPLLGRP_DDRDQSCLK_PHASE_MASK);
-
-	/* SDRAM DDR2XDQSCLK */
-	cm_write_with_phase(cfg->ddr2xdqsclk,
-			    (uint32_t)&clock_manager_base->sdr_pll.ddr2xdqsclk,
-			    CLKMGR_SDRPLLGRP_DDR2XDQSCLK_PHASE_MASK);
-
-	cm_write_with_phase(cfg->ddrdqclk,
-			    (uint32_t)&clock_manager_base->sdr_pll.ddrdqclk,
-			    CLKMGR_SDRPLLGRP_DDRDQCLK_PHASE_MASK);
-
-	cm_write_with_phase(cfg->s2fuser2clk,
-			    (uint32_t)&clock_manager_base->sdr_pll.s2fuser2clk,
-			    CLKMGR_SDRPLLGRP_S2FUSER2CLK_PHASE_MASK);
-
-	/* Take all three PLLs out of bypass when safe mode is cleared. */
-	cm_write_bypass(0);
-
-	/* clear safe mode */
-	cm_write_ctrl(readl(&clock_manager_base->ctrl) | CLKMGR_CTRL_SAFEMODE);
-
-	/*
-	 * now that safe mode is clear with clocks gated
-	 * it safe to change the source mux for the flashes the the L4_MAIN
-	 */
-	writel(cfg->persrc, &clock_manager_base->per_pll.src);
-	writel(cfg->l4src, &clock_manager_base->main_pll.l4src);
-
-	/* Now ungate non-hw-managed clocks */
-	writel(~0, &clock_manager_base->main_pll.en);
-	writel(~0, &clock_manager_base->per_pll.en);
-	writel(~0, &clock_manager_base->sdr_pll.en);
-
-	/* Clear the loss of lock bits (write 1 to clear) */
-	writel(CLKMGR_INTER_SDRPLLLOST_MASK | CLKMGR_INTER_PERPLLLOST_MASK |
-	       CLKMGR_INTER_MAINPLLLOST_MASK,
-	       &clock_manager_base->inter);
-}
-
-static unsigned int cm_get_main_vco_clk_hz(void)
-{
-	uint32_t reg, clock;
-
-	/* get the main VCO clock */
-	reg = readl(&clock_manager_base->main_pll.vco);
-	clock = cm_get_osc_clk_hz(1);
-	clock /= ((reg & CLKMGR_MAINPLLGRP_VCO_DENOM_MASK) >>
-		  CLKMGR_MAINPLLGRP_VCO_DENOM_OFFSET) + 1;
-	clock *= ((reg & CLKMGR_MAINPLLGRP_VCO_NUMER_MASK) >>
-		  CLKMGR_MAINPLLGRP_VCO_NUMER_OFFSET) + 1;
-
-	return clock;
-}
-
-static unsigned int cm_get_per_vco_clk_hz(void)
-{
-	uint32_t reg, clock = 0;
-
-	/* identify PER PLL clock source */
-	reg = readl(&clock_manager_base->per_pll.vco);
-	reg = (reg & CLKMGR_PERPLLGRP_VCO_SSRC_MASK) >>
-	      CLKMGR_PERPLLGRP_VCO_SSRC_OFFSET;
-	if (reg == CLKMGR_VCO_SSRC_EOSC1)
-		clock = cm_get_osc_clk_hz(1);
-	else if (reg == CLKMGR_VCO_SSRC_EOSC2)
-		clock = cm_get_osc_clk_hz(2);
-	else if (reg == CLKMGR_VCO_SSRC_F2S)
-		clock = cm_get_f2s_per_ref_clk_hz();
-
-	/* get the PER VCO clock */
-	reg = readl(&clock_manager_base->per_pll.vco);
-	clock /= ((reg & CLKMGR_PERPLLGRP_VCO_DENOM_MASK) >>
-		  CLKMGR_PERPLLGRP_VCO_DENOM_OFFSET) + 1;
-	clock *= ((reg & CLKMGR_PERPLLGRP_VCO_NUMER_MASK) >>
-		  CLKMGR_PERPLLGRP_VCO_NUMER_OFFSET) + 1;
-
-	return clock;
-}
-
-unsigned long cm_get_mpu_clk_hz(void)
-{
-	uint32_t reg, clock;
-
-	clock = cm_get_main_vco_clk_hz();
-
-	/* get the MPU clock */
-	reg = readl(&clock_manager_base->altera.mpuclk);
-	clock /= (reg + 1);
-	reg = readl(&clock_manager_base->main_pll.mpuclk);
-	clock /= (reg + 1);
-	return clock;
-}
-
-unsigned long cm_get_sdram_clk_hz(void)
-{
-	uint32_t reg, clock = 0;
-
-	/* identify SDRAM PLL clock source */
-	reg = readl(&clock_manager_base->sdr_pll.vco);
-	reg = (reg & CLKMGR_SDRPLLGRP_VCO_SSRC_MASK) >>
-	      CLKMGR_SDRPLLGRP_VCO_SSRC_OFFSET;
-	if (reg == CLKMGR_VCO_SSRC_EOSC1)
-		clock = cm_get_osc_clk_hz(1);
-	else if (reg == CLKMGR_VCO_SSRC_EOSC2)
-		clock = cm_get_osc_clk_hz(2);
-	else if (reg == CLKMGR_VCO_SSRC_F2S)
-		clock = cm_get_f2s_sdr_ref_clk_hz();
-
-	/* get the SDRAM VCO clock */
-	reg = readl(&clock_manager_base->sdr_pll.vco);
-	clock /= ((reg & CLKMGR_SDRPLLGRP_VCO_DENOM_MASK) >>
-		  CLKMGR_SDRPLLGRP_VCO_DENOM_OFFSET) + 1;
-	clock *= ((reg & CLKMGR_SDRPLLGRP_VCO_NUMER_MASK) >>
-		  CLKMGR_SDRPLLGRP_VCO_NUMER_OFFSET) + 1;
-
-	/* get the SDRAM (DDR_DQS) clock */
-	reg = readl(&clock_manager_base->sdr_pll.ddrdqsclk);
-	reg = (reg & CLKMGR_SDRPLLGRP_DDRDQSCLK_CNT_MASK) >>
-	      CLKMGR_SDRPLLGRP_DDRDQSCLK_CNT_OFFSET;
-	clock /= (reg + 1);
-
-	return clock;
-}
-
-unsigned int cm_get_l4_sp_clk_hz(void)
-{
-	uint32_t reg, clock = 0;
-
-	/* identify the source of L4 SP clock */
-	reg = readl(&clock_manager_base->main_pll.l4src);
-	reg = (reg & CLKMGR_MAINPLLGRP_L4SRC_L4SP) >>
-	      CLKMGR_MAINPLLGRP_L4SRC_L4SP_OFFSET;
-
-	if (reg == CLKMGR_L4_SP_CLK_SRC_MAINPLL) {
-		clock = cm_get_main_vco_clk_hz();
-
-		/* get the clock prior L4 SP divider (main clk) */
-		reg = readl(&clock_manager_base->altera.mainclk);
-		clock /= (reg + 1);
-		reg = readl(&clock_manager_base->main_pll.mainclk);
-		clock /= (reg + 1);
-	} else if (reg == CLKMGR_L4_SP_CLK_SRC_PERPLL) {
-		clock = cm_get_per_vco_clk_hz();
-
-		/* get the clock prior L4 SP divider (periph_base_clk) */
-		reg = readl(&clock_manager_base->per_pll.perbaseclk);
-		clock /= (reg + 1);
-	}
-
-	/* get the L4 SP clock which supplied to UART */
-	reg = readl(&clock_manager_base->main_pll.maindiv);
-	reg = (reg & CLKMGR_MAINPLLGRP_MAINDIV_L4SPCLK_MASK) >>
-	      CLKMGR_MAINPLLGRP_MAINDIV_L4SPCLK_OFFSET;
-	clock = clock / (1 << reg);
-
-	return clock;
-}
-
-unsigned int cm_get_mmc_controller_clk_hz(void)
-{
-	uint32_t reg, clock = 0;
-
-	/* identify the source of MMC clock */
-	reg = readl(&clock_manager_base->per_pll.src);
-	reg = (reg & CLKMGR_PERPLLGRP_SRC_SDMMC_MASK) >>
-	      CLKMGR_PERPLLGRP_SRC_SDMMC_OFFSET;
-
-	if (reg == CLKMGR_SDMMC_CLK_SRC_F2S) {
-		clock = cm_get_f2s_per_ref_clk_hz();
-	} else if (reg == CLKMGR_SDMMC_CLK_SRC_MAIN) {
-		clock = cm_get_main_vco_clk_hz();
-
-		/* get the SDMMC clock */
-		reg = readl(&clock_manager_base->main_pll.mainnandsdmmcclk);
-		clock /= (reg + 1);
-	} else if (reg == CLKMGR_SDMMC_CLK_SRC_PER) {
-		clock = cm_get_per_vco_clk_hz();
-
-		/* get the SDMMC clock */
-		reg = readl(&clock_manager_base->per_pll.pernandsdmmcclk);
-		clock /= (reg + 1);
-	}
-
-	/* further divide by 4 as we have fixed divider at wrapper */
-	clock /= 4;
-	return clock;
-}
-
-unsigned int cm_get_qspi_controller_clk_hz(void)
-{
-	uint32_t reg, clock = 0;
-
-	/* identify the source of QSPI clock */
-	reg = readl(&clock_manager_base->per_pll.src);
-	reg = (reg & CLKMGR_PERPLLGRP_SRC_QSPI_MASK) >>
-	      CLKMGR_PERPLLGRP_SRC_QSPI_OFFSET;
-
-	if (reg == CLKMGR_QSPI_CLK_SRC_F2S) {
-		clock = cm_get_f2s_per_ref_clk_hz();
-	} else if (reg == CLKMGR_QSPI_CLK_SRC_MAIN) {
-		clock = cm_get_main_vco_clk_hz();
-
-		/* get the qspi clock */
-		reg = readl(&clock_manager_base->main_pll.mainqspiclk);
-		clock /= (reg + 1);
-	} else if (reg == CLKMGR_QSPI_CLK_SRC_PER) {
-		clock = cm_get_per_vco_clk_hz();
-
-		/* get the qspi clock */
-		reg = readl(&clock_manager_base->per_pll.perqspiclk);
-		clock /= (reg + 1);
-	}
-
-	return clock;
-}
-
-unsigned int cm_get_spi_controller_clk_hz(void)
-{
-	uint32_t reg, clock = 0;
-
-	clock = cm_get_per_vco_clk_hz();
-
-	/* get the clock prior L4 SP divider (periph_base_clk) */
-	reg = readl(&clock_manager_base->per_pll.perbaseclk);
-	clock /= (reg + 1);
-
-	return clock;
-}
-
-static void cm_print_clock_quick_summary(void)
-{
-	printf("MPU       %10ld kHz\n", cm_get_mpu_clk_hz() / 1000);
-	printf("DDR       %10ld kHz\n", cm_get_sdram_clk_hz() / 1000);
-	printf("EOSC1       %8d kHz\n", cm_get_osc_clk_hz(1) / 1000);
-	printf("EOSC2       %8d kHz\n", cm_get_osc_clk_hz(2) / 1000);
-	printf("F2S_SDR_REF %8d kHz\n", cm_get_f2s_sdr_ref_clk_hz() / 1000);
-	printf("F2S_PER_REF %8d kHz\n", cm_get_f2s_per_ref_clk_hz() / 1000);
-	printf("MMC         %8d kHz\n", cm_get_mmc_controller_clk_hz() / 1000);
-	printf("QSPI        %8d kHz\n", cm_get_qspi_controller_clk_hz() / 1000);
-	printf("UART        %8d kHz\n", cm_get_l4_sp_clk_hz() / 1000);
-	printf("SPI         %8d kHz\n", cm_get_spi_controller_clk_hz() / 1000);
-}
-
 int set_cpu_clk_info(void)
 {
 	/* Calculate the clock frequencies required for drivers */
diff --git a/arch/arm/mach-socfpga/clock_manager_gen5.c b/arch/arm/mach-socfpga/clock_manager_gen5.c
new file mode 100644
index 0000000..bca27df
--- /dev/null
+++ b/arch/arm/mach-socfpga/clock_manager_gen5.c
@@ -0,0 +1,510 @@
+/*
+ *  Copyright (C) 2013-2017 Altera Corporation <www.altera.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/clock_manager.h>
+#include <wait_bit.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static const struct socfpga_clock_manager *clock_manager_base =
+	(struct socfpga_clock_manager *)SOCFPGA_CLKMGR_ADDRESS;
+
+/*
+ * function to write the bypass register which requires a poll of the
+ * busy bit
+ */
+static void cm_write_bypass(u32 val)
+{
+	writel(val, &clock_manager_base->bypass);
+	cm_wait_for_fsm();
+}
+
+/* function to write the ctrl register which requires a poll of the busy bit */
+static void cm_write_ctrl(u32 val)
+{
+	writel(val, &clock_manager_base->ctrl);
+	cm_wait_for_fsm();
+}
+
+/* function to write a clock register that has phase information */
+static void cm_write_with_phase(u32 value,
+				u32 reg_address, u32 mask)
+{
+	/* poll until phase is zero */
+	err = wait_for_bit(__func__, (const u32 *)reg_address, mask,
+			   false, 20000, false);
+
+	writel(value, reg_address);
+
+	err = wait_for_bit(__func__, (const u32 *)reg_address, mask,
+			   false, 20000, false);
+}
+
+/*
+ * Setup clocks while making no assumptions about previous state of the clocks.
+ *
+ * Start by being paranoid and gate all sw managed clocks
+ * Put all plls in bypass
+ * Put all plls VCO registers back to reset value (bandgap power down).
+ * Put peripheral and main pll src to reset value to avoid glitch.
+ * Delay 5 us.
+ * Deassert bandgap power down and set numerator and denominator
+ * Start 7 us timer.
+ * set internal dividers
+ * Wait for 7 us timer.
+ * Enable plls
+ * Set external dividers while plls are locking
+ * Wait for pll lock
+ * Assert/deassert outreset all.
+ * Take all pll's out of bypass
+ * Clear safe mode
+ * set source main and peripheral clocks
+ * Ungate clocks
+ */
+
+void cm_basic_init(const struct cm_config * const cfg)
+{
+	unsigned long end;
+
+	/* Start by being paranoid and gate all sw managed clocks */
+
+	/*
+	 * We need to disable nandclk
+	 * and then do another apb access before disabling
+	 * gatting off the rest of the periperal clocks.
+	 */
+	writel(~CLKMGR_PERPLLGRP_EN_NANDCLK_MASK &
+		readl(&clock_manager_base->per_pll.en),
+		&clock_manager_base->per_pll.en);
+
+	/* DO NOT GATE OFF DEBUG CLOCKS & BRIDGE CLOCKS */
+	writel(CLKMGR_MAINPLLGRP_EN_DBGTIMERCLK_MASK |
+		CLKMGR_MAINPLLGRP_EN_DBGTRACECLK_MASK |
+		CLKMGR_MAINPLLGRP_EN_DBGCLK_MASK |
+		CLKMGR_MAINPLLGRP_EN_DBGATCLK_MASK |
+		CLKMGR_MAINPLLGRP_EN_S2FUSER0CLK_MASK |
+		CLKMGR_MAINPLLGRP_EN_L4MPCLK_MASK,
+		&clock_manager_base->main_pll.en);
+
+	writel(0, &clock_manager_base->sdr_pll.en);
+
+	/* now we can gate off the rest of the peripheral clocks */
+	writel(0, &clock_manager_base->per_pll.en);
+
+	/* Put all plls in bypass */
+	cm_write_bypass(CLKMGR_BYPASS_PERPLL | CLKMGR_BYPASS_SDRPLL |
+			CLKMGR_BYPASS_MAINPLL);
+
+	/* Put all plls VCO registers back to reset value. */
+	writel(CLKMGR_MAINPLLGRP_VCO_RESET_VALUE &
+	       ~CLKMGR_MAINPLLGRP_VCO_REGEXTSEL_MASK,
+	       &clock_manager_base->main_pll.vco);
+	writel(CLKMGR_PERPLLGRP_VCO_RESET_VALUE &
+	       ~CLKMGR_PERPLLGRP_VCO_REGEXTSEL_MASK,
+	       &clock_manager_base->per_pll.vco);
+	writel(CLKMGR_SDRPLLGRP_VCO_RESET_VALUE &
+	       ~CLKMGR_SDRPLLGRP_VCO_REGEXTSEL_MASK,
+	       &clock_manager_base->sdr_pll.vco);
+
+	/*
+	 * The clocks to the flash devices and the L4_MAIN clocks can
+	 * glitch when coming out of safe mode if their source values
+	 * are different from their reset value.  So the trick it to
+	 * put them back to their reset state, and change input
+	 * after exiting safe mode but before ungating the clocks.
+	 */
+	writel(CLKMGR_PERPLLGRP_SRC_RESET_VALUE,
+	       &clock_manager_base->per_pll.src);
+	writel(CLKMGR_MAINPLLGRP_L4SRC_RESET_VALUE,
+	       &clock_manager_base->main_pll.l4src);
+
+	/* read back for the required 5 us delay. */
+	readl(&clock_manager_base->main_pll.vco);
+	readl(&clock_manager_base->per_pll.vco);
+	readl(&clock_manager_base->sdr_pll.vco);
+
+
+	/*
+	 * We made sure bgpwr down was assert for 5 us. Now deassert BG PWR DN
+	 * with numerator and denominator.
+	 */
+	writel(cfg->main_vco_base, &clock_manager_base->main_pll.vco);
+	writel(cfg->peri_vco_base, &clock_manager_base->per_pll.vco);
+	writel(cfg->sdram_vco_base, &clock_manager_base->sdr_pll.vco);
+
+	/*
+	 * Time starts here. Must wait 7 us from
+	 * BGPWRDN_SET(0) to VCO_ENABLE_SET(1).
+	 */
+	end = timer_get_us() + 7;
+
+	/* main mpu */
+	writel(cfg->mpuclk, &clock_manager_base->main_pll.mpuclk);
+
+	/* altera group mpuclk */
+	writel(cfg->altera_grp_mpuclk, &clock_manager_base->altera.mpuclk);
+
+	/* main main clock */
+	writel(cfg->mainclk, &clock_manager_base->main_pll.mainclk);
+
+	/* main for dbg */
+	writel(cfg->dbgatclk, &clock_manager_base->main_pll.dbgatclk);
+
+	/* main for cfgs2fuser0clk */
+	writel(cfg->cfg2fuser0clk,
+	       &clock_manager_base->main_pll.cfgs2fuser0clk);
+
+	/* Peri emac0 50 MHz default to RMII */
+	writel(cfg->emac0clk, &clock_manager_base->per_pll.emac0clk);
+
+	/* Peri emac1 50 MHz default to RMII */
+	writel(cfg->emac1clk, &clock_manager_base->per_pll.emac1clk);
+
+	/* Peri QSPI */
+	writel(cfg->mainqspiclk, &clock_manager_base->main_pll.mainqspiclk);
+
+	writel(cfg->perqspiclk, &clock_manager_base->per_pll.perqspiclk);
+
+	/* Peri pernandsdmmcclk */
+	writel(cfg->mainnandsdmmcclk,
+	       &clock_manager_base->main_pll.mainnandsdmmcclk);
+
+	writel(cfg->pernandsdmmcclk,
+	       &clock_manager_base->per_pll.pernandsdmmcclk);
+
+	/* Peri perbaseclk */
+	writel(cfg->perbaseclk, &clock_manager_base->per_pll.perbaseclk);
+
+	/* Peri s2fuser1clk */
+	writel(cfg->s2fuser1clk, &clock_manager_base->per_pll.s2fuser1clk);
+
+	/* 7 us must have elapsed before we can enable the VCO */
+	while (timer_get_us() < end)
+		;
+
+	/* Enable vco */
+	/* main pll vco */
+	writel(cfg->main_vco_base | CLKMGR_MAINPLLGRP_VCO_EN,
+	       &clock_manager_base->main_pll.vco);
+
+	/* periferal pll */
+	writel(cfg->peri_vco_base | CLKMGR_MAINPLLGRP_VCO_EN,
+	       &clock_manager_base->per_pll.vco);
+
+	/* sdram pll vco */
+	writel(cfg->sdram_vco_base | CLKMGR_MAINPLLGRP_VCO_EN,
+	       &clock_manager_base->sdr_pll.vco);
+
+	/* L3 MP and L3 SP */
+	writel(cfg->maindiv, &clock_manager_base->main_pll.maindiv);
+
+	writel(cfg->dbgdiv, &clock_manager_base->main_pll.dbgdiv);
+
+	writel(cfg->tracediv, &clock_manager_base->main_pll.tracediv);
+
+	/* L4 MP, L4 SP, can0, and can1 */
+	writel(cfg->perdiv, &clock_manager_base->per_pll.div);
+
+	writel(cfg->gpiodiv, &clock_manager_base->per_pll.gpiodiv);
+
+	cm_wait_for_lock(LOCKED_MASK);
+
+	/* write the sdram clock counters before toggling outreset all */
+	writel(cfg->ddrdqsclk & CLKMGR_SDRPLLGRP_DDRDQSCLK_CNT_MASK,
+	       &clock_manager_base->sdr_pll.ddrdqsclk);
+
+	writel(cfg->ddr2xdqsclk & CLKMGR_SDRPLLGRP_DDR2XDQSCLK_CNT_MASK,
+	       &clock_manager_base->sdr_pll.ddr2xdqsclk);
+
+	writel(cfg->ddrdqclk & CLKMGR_SDRPLLGRP_DDRDQCLK_CNT_MASK,
+	       &clock_manager_base->sdr_pll.ddrdqclk);
+
+	writel(cfg->s2fuser2clk & CLKMGR_SDRPLLGRP_S2FUSER2CLK_CNT_MASK,
+	       &clock_manager_base->sdr_pll.s2fuser2clk);
+
+	/*
+	 * after locking, but before taking out of bypass
+	 * assert/deassert outresetall
+	 */
+	u32 mainvco = readl(&clock_manager_base->main_pll.vco);
+
+	/* assert main outresetall */
+	writel(mainvco | CLKMGR_MAINPLLGRP_VCO_OUTRESETALL_MASK,
+	       &clock_manager_base->main_pll.vco);
+
+	u32 periphvco = readl(&clock_manager_base->per_pll.vco);
+
+	/* assert pheriph outresetall */
+	writel(periphvco | CLKMGR_PERPLLGRP_VCO_OUTRESETALL_MASK,
+	       &clock_manager_base->per_pll.vco);
+
+	/* assert sdram outresetall */
+	writel(cfg->sdram_vco_base | CLKMGR_MAINPLLGRP_VCO_EN|
+		CLKMGR_SDRPLLGRP_VCO_OUTRESETALL,
+		&clock_manager_base->sdr_pll.vco);
+
+	/* deassert main outresetall */
+	writel(mainvco & ~CLKMGR_MAINPLLGRP_VCO_OUTRESETALL_MASK,
+	       &clock_manager_base->main_pll.vco);
+
+	/* deassert pheriph outresetall */
+	writel(periphvco & ~CLKMGR_PERPLLGRP_VCO_OUTRESETALL_MASK,
+	       &clock_manager_base->per_pll.vco);
+
+	/* deassert sdram outresetall */
+	writel(cfg->sdram_vco_base | CLKMGR_MAINPLLGRP_VCO_EN,
+	       &clock_manager_base->sdr_pll.vco);
+
+	/*
+	 * now that we've toggled outreset all, all the clocks
+	 * are aligned nicely; so we can change any phase.
+	 */
+	cm_write_with_phase(cfg->ddrdqsclk,
+			    (u32)&clock_manager_base->sdr_pll.ddrdqsclk,
+			    CLKMGR_SDRPLLGRP_DDRDQSCLK_PHASE_MASK);
+
+	/* SDRAM DDR2XDQSCLK */
+	cm_write_with_phase(cfg->ddr2xdqsclk,
+			    (u32)&clock_manager_base->sdr_pll.ddr2xdqsclk,
+			    CLKMGR_SDRPLLGRP_DDR2XDQSCLK_PHASE_MASK);
+
+	cm_write_with_phase(cfg->ddrdqclk,
+			    (u32)&clock_manager_base->sdr_pll.ddrdqclk,
+			    CLKMGR_SDRPLLGRP_DDRDQCLK_PHASE_MASK);
+
+	cm_write_with_phase(cfg->s2fuser2clk,
+			    (u32)&clock_manager_base->sdr_pll.s2fuser2clk,
+			    CLKMGR_SDRPLLGRP_S2FUSER2CLK_PHASE_MASK);
+
+	/* Take all three PLLs out of bypass when safe mode is cleared. */
+	cm_write_bypass(0);
+
+	/* clear safe mode */
+	cm_write_ctrl(readl(&clock_manager_base->ctrl) | CLKMGR_CTRL_SAFEMODE);
+
+	/*
+	 * now that safe mode is clear with clocks gated
+	 * it safe to change the source mux for the flashes the the L4_MAIN
+	 */
+	writel(cfg->persrc, &clock_manager_base->per_pll.src);
+	writel(cfg->l4src, &clock_manager_base->main_pll.l4src);
+
+	/* Now ungate non-hw-managed clocks */
+	writel(~0, &clock_manager_base->main_pll.en);
+	writel(~0, &clock_manager_base->per_pll.en);
+	writel(~0, &clock_manager_base->sdr_pll.en);
+
+	/* Clear the loss of lock bits (write 1 to clear) */
+	writel(CLKMGR_INTER_SDRPLLLOST_MASK | CLKMGR_INTER_PERPLLLOST_MASK |
+	       CLKMGR_INTER_MAINPLLLOST_MASK,
+	       &clock_manager_base->inter);
+}
+
+static unsigned int cm_get_main_vco_clk_hz(void)
+{
+	u32 reg, clock;
+
+	/* get the main VCO clock */
+	reg = readl(&clock_manager_base->main_pll.vco);
+	clock = cm_get_osc_clk_hz(1);
+	clock /= ((reg & CLKMGR_MAINPLLGRP_VCO_DENOM_MASK) >>
+		  CLKMGR_MAINPLLGRP_VCO_DENOM_OFFSET) + 1;
+	clock *= ((reg & CLKMGR_MAINPLLGRP_VCO_NUMER_MASK) >>
+		  CLKMGR_MAINPLLGRP_VCO_NUMER_OFFSET) + 1;
+
+	return clock;
+}
+
+static unsigned int cm_get_per_vco_clk_hz(void)
+{
+	u32 reg, clock = 0;
+
+	/* identify PER PLL clock source */
+	reg = readl(&clock_manager_base->per_pll.vco);
+	reg = (reg & CLKMGR_PERPLLGRP_VCO_SSRC_MASK) >>
+	      CLKMGR_PERPLLGRP_VCO_SSRC_OFFSET;
+	if (reg == CLKMGR_VCO_SSRC_EOSC1)
+		clock = cm_get_osc_clk_hz(1);
+	else if (reg == CLKMGR_VCO_SSRC_EOSC2)
+		clock = cm_get_osc_clk_hz(2);
+	else if (reg == CLKMGR_VCO_SSRC_F2S)
+		clock = cm_get_f2s_per_ref_clk_hz();
+
+	/* get the PER VCO clock */
+	reg = readl(&clock_manager_base->per_pll.vco);
+	clock /= ((reg & CLKMGR_PERPLLGRP_VCO_DENOM_MASK) >>
+		  CLKMGR_PERPLLGRP_VCO_DENOM_OFFSET) + 1;
+	clock *= ((reg & CLKMGR_PERPLLGRP_VCO_NUMER_MASK) >>
+		  CLKMGR_PERPLLGRP_VCO_NUMER_OFFSET) + 1;
+
+	return clock;
+}
+
+unsigned long cm_get_mpu_clk_hz(void)
+{
+	u32 reg, clock;
+
+	clock = cm_get_main_vco_clk_hz();
+
+	/* get the MPU clock */
+	reg = readl(&clock_manager_base->altera.mpuclk);
+	clock /= (reg + 1);
+	reg = readl(&clock_manager_base->main_pll.mpuclk);
+	clock /= (reg + 1);
+	return clock;
+}
+
+unsigned long cm_get_sdram_clk_hz(void)
+{
+	u32 reg, clock = 0;
+
+	/* identify SDRAM PLL clock source */
+	reg = readl(&clock_manager_base->sdr_pll.vco);
+	reg = (reg & CLKMGR_SDRPLLGRP_VCO_SSRC_MASK) >>
+	      CLKMGR_SDRPLLGRP_VCO_SSRC_OFFSET;
+	if (reg == CLKMGR_VCO_SSRC_EOSC1)
+		clock = cm_get_osc_clk_hz(1);
+	else if (reg == CLKMGR_VCO_SSRC_EOSC2)
+		clock = cm_get_osc_clk_hz(2);
+	else if (reg == CLKMGR_VCO_SSRC_F2S)
+		clock = cm_get_f2s_sdr_ref_clk_hz();
+
+	/* get the SDRAM VCO clock */
+	reg = readl(&clock_manager_base->sdr_pll.vco);
+	clock /= ((reg & CLKMGR_SDRPLLGRP_VCO_DENOM_MASK) >>
+		  CLKMGR_SDRPLLGRP_VCO_DENOM_OFFSET) + 1;
+	clock *= ((reg & CLKMGR_SDRPLLGRP_VCO_NUMER_MASK) >>
+		  CLKMGR_SDRPLLGRP_VCO_NUMER_OFFSET) + 1;
+
+	/* get the SDRAM (DDR_DQS) clock */
+	reg = readl(&clock_manager_base->sdr_pll.ddrdqsclk);
+	reg = (reg & CLKMGR_SDRPLLGRP_DDRDQSCLK_CNT_MASK) >>
+	      CLKMGR_SDRPLLGRP_DDRDQSCLK_CNT_OFFSET;
+	clock /= (reg + 1);
+
+	return clock;
+}
+
+unsigned int cm_get_l4_sp_clk_hz(void)
+{
+	u32 reg, clock = 0;
+
+	/* identify the source of L4 SP clock */
+	reg = readl(&clock_manager_base->main_pll.l4src);
+	reg = (reg & CLKMGR_MAINPLLGRP_L4SRC_L4SP) >>
+	      CLKMGR_MAINPLLGRP_L4SRC_L4SP_OFFSET;
+
+	if (reg == CLKMGR_L4_SP_CLK_SRC_MAINPLL) {
+		clock = cm_get_main_vco_clk_hz();
+
+		/* get the clock prior L4 SP divider (main clk) */
+		reg = readl(&clock_manager_base->altera.mainclk);
+		clock /= (reg + 1);
+		reg = readl(&clock_manager_base->main_pll.mainclk);
+		clock /= (reg + 1);
+	} else if (reg == CLKMGR_L4_SP_CLK_SRC_PERPLL) {
+		clock = cm_get_per_vco_clk_hz();
+
+		/* get the clock prior L4 SP divider (periph_base_clk) */
+		reg = readl(&clock_manager_base->per_pll.perbaseclk);
+		clock /= (reg + 1);
+	}
+
+	/* get the L4 SP clock which supplied to UART */
+	reg = readl(&clock_manager_base->main_pll.maindiv);
+	reg = (reg & CLKMGR_MAINPLLGRP_MAINDIV_L4SPCLK_MASK) >>
+	      CLKMGR_MAINPLLGRP_MAINDIV_L4SPCLK_OFFSET;
+	clock = clock / (1 << reg);
+
+	return clock;
+}
+
+unsigned int cm_get_mmc_controller_clk_hz(void)
+{
+	u32 reg, clock = 0;
+
+	/* identify the source of MMC clock */
+	reg = readl(&clock_manager_base->per_pll.src);
+	reg = (reg & CLKMGR_PERPLLGRP_SRC_SDMMC_MASK) >>
+	      CLKMGR_PERPLLGRP_SRC_SDMMC_OFFSET;
+
+	if (reg == CLKMGR_SDMMC_CLK_SRC_F2S) {
+		clock = cm_get_f2s_per_ref_clk_hz();
+	} else if (reg == CLKMGR_SDMMC_CLK_SRC_MAIN) {
+		clock = cm_get_main_vco_clk_hz();
+
+		/* get the SDMMC clock */
+		reg = readl(&clock_manager_base->main_pll.mainnandsdmmcclk);
+		clock /= (reg + 1);
+	} else if (reg == CLKMGR_SDMMC_CLK_SRC_PER) {
+		clock = cm_get_per_vco_clk_hz();
+
+		/* get the SDMMC clock */
+		reg = readl(&clock_manager_base->per_pll.pernandsdmmcclk);
+		clock /= (reg + 1);
+	}
+
+	/* further divide by 4 as we have fixed divider at wrapper */
+	clock /= 4;
+	return clock;
+}
+
+unsigned int cm_get_qspi_controller_clk_hz(void)
+{
+	u32 reg, clock = 0;
+
+	/* identify the source of QSPI clock */
+	reg = readl(&clock_manager_base->per_pll.src);
+	reg = (reg & CLKMGR_PERPLLGRP_SRC_QSPI_MASK) >>
+	      CLKMGR_PERPLLGRP_SRC_QSPI_OFFSET;
+
+	if (reg == CLKMGR_QSPI_CLK_SRC_F2S) {
+		clock = cm_get_f2s_per_ref_clk_hz();
+	} else if (reg == CLKMGR_QSPI_CLK_SRC_MAIN) {
+		clock = cm_get_main_vco_clk_hz();
+
+		/* get the qspi clock */
+		reg = readl(&clock_manager_base->main_pll.mainqspiclk);
+		clock /= (reg + 1);
+	} else if (reg == CLKMGR_QSPI_CLK_SRC_PER) {
+		clock = cm_get_per_vco_clk_hz();
+
+		/* get the qspi clock */
+		reg = readl(&clock_manager_base->per_pll.perqspiclk);
+		clock /= (reg + 1);
+	}
+
+	return clock;
+}
+
+unsigned int cm_get_spi_controller_clk_hz(void)
+{
+	u32 reg, clock = 0;
+
+	clock = cm_get_per_vco_clk_hz();
+
+	/* get the clock prior L4 SP divider (periph_base_clk) */
+	reg = readl(&clock_manager_base->per_pll.perbaseclk);
+	clock /= (reg + 1);
+
+	return clock;
+}
+
+void cm_print_clock_quick_summary(void)
+{
+	printf("MPU       %10ld kHz\n", cm_get_mpu_clk_hz() / 1000);
+	printf("DDR       %10ld kHz\n", cm_get_sdram_clk_hz() / 1000);
+	printf("EOSC1       %8d kHz\n", cm_get_osc_clk_hz(1) / 1000);
+	printf("EOSC2       %8d kHz\n", cm_get_osc_clk_hz(2) / 1000);
+	printf("F2S_SDR_REF %8d kHz\n", cm_get_f2s_sdr_ref_clk_hz() / 1000);
+	printf("F2S_PER_REF %8d kHz\n", cm_get_f2s_per_ref_clk_hz() / 1000);
+	printf("MMC         %8d kHz\n", cm_get_mmc_controller_clk_hz() / 1000);
+	printf("QSPI        %8d kHz\n", cm_get_qspi_controller_clk_hz() / 1000);
+	printf("UART        %8d kHz\n", cm_get_l4_sp_clk_hz() / 1000);
+	printf("SPI         %8d kHz\n", cm_get_spi_controller_clk_hz() / 1000);
+}
diff --git a/arch/arm/mach-socfpga/include/mach/clock_manager.h b/arch/arm/mach-socfpga/include/mach/clock_manager.h
index 803c926..d0d0487 100644
--- a/arch/arm/mach-socfpga/include/mach/clock_manager.h
+++ b/arch/arm/mach-socfpga/include/mach/clock_manager.h
@@ -1,5 +1,5 @@
 /*
- *  Copyright (C) 2013 Altera Corporation <www.altera.com>
+ *  Copyright (C) 2013-2017 Altera Corporation <www.altera.com>
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */
@@ -8,310 +8,12 @@
 #define	_CLOCK_MANAGER_H_
 
 #ifndef __ASSEMBLER__
-/* Clock speed accessors */
-unsigned long cm_get_mpu_clk_hz(void);
-unsigned long cm_get_sdram_clk_hz(void);
-unsigned int cm_get_l4_sp_clk_hz(void);
-unsigned int cm_get_mmc_controller_clk_hz(void);
-unsigned int cm_get_qspi_controller_clk_hz(void);
-unsigned int cm_get_spi_controller_clk_hz(void);
-const unsigned int cm_get_osc_clk_hz(const int osc);
-const unsigned int cm_get_f2s_per_ref_clk_hz(void);
-const unsigned int cm_get_f2s_sdr_ref_clk_hz(void);
-
-/* Clock configuration accessors */
-const struct cm_config * const cm_get_default_config(void);
+void cm_wait_for_lock(u32 mask);
+void cm_wait_for_fsm(void);
+void cm_print_clock_quick_summary(void);
 #endif
 
-struct cm_config {
-	/* main group */
-	uint32_t main_vco_base;
-	uint32_t mpuclk;
-	uint32_t mainclk;
-	uint32_t dbgatclk;
-	uint32_t mainqspiclk;
-	uint32_t mainnandsdmmcclk;
-	uint32_t cfg2fuser0clk;
-	uint32_t maindiv;
-	uint32_t dbgdiv;
-	uint32_t tracediv;
-	uint32_t l4src;
-
-	/* peripheral group */
-	uint32_t peri_vco_base;
-	uint32_t emac0clk;
-	uint32_t emac1clk;
-	uint32_t perqspiclk;
-	uint32_t pernandsdmmcclk;
-	uint32_t perbaseclk;
-	uint32_t s2fuser1clk;
-	uint32_t perdiv;
-	uint32_t gpiodiv;
-	uint32_t persrc;
-
-	/* sdram pll group */
-	uint32_t sdram_vco_base;
-	uint32_t ddrdqsclk;
-	uint32_t ddr2xdqsclk;
-	uint32_t ddrdqclk;
-	uint32_t s2fuser2clk;
-
-	/* altera group */
-	uint32_t altera_grp_mpuclk;
-};
-
-void cm_basic_init(const struct cm_config * const cfg);
-
-struct socfpga_clock_manager_main_pll {
-	u32	vco;
-	u32	misc;
-	u32	mpuclk;
-	u32	mainclk;
-	u32	dbgatclk;
-	u32	mainqspiclk;
-	u32	mainnandsdmmcclk;
-	u32	cfgs2fuser0clk;
-	u32	en;
-	u32	maindiv;
-	u32	dbgdiv;
-	u32	tracediv;
-	u32	l4src;
-	u32	stat;
-	u32	_pad_0x38_0x40[2];
-};
-
-struct socfpga_clock_manager_per_pll {
-	u32	vco;
-	u32	misc;
-	u32	emac0clk;
-	u32	emac1clk;
-	u32	perqspiclk;
-	u32	pernandsdmmcclk;
-	u32	perbaseclk;
-	u32	s2fuser1clk;
-	u32	en;
-	u32	div;
-	u32	gpiodiv;
-	u32	src;
-	u32	stat;
-	u32	_pad_0x34_0x40[3];
-};
-
-struct socfpga_clock_manager_sdr_pll {
-	u32	vco;
-	u32	ctrl;
-	u32	ddrdqsclk;
-	u32	ddr2xdqsclk;
-	u32	ddrdqclk;
-	u32	s2fuser2clk;
-	u32	en;
-	u32	stat;
-};
-
-struct socfpga_clock_manager_altera {
-	u32	mpuclk;
-	u32	mainclk;
-};
-
-struct socfpga_clock_manager {
-	u32	ctrl;
-	u32	bypass;
-	u32	inter;
-	u32	intren;
-	u32	dbctrl;
-	u32	stat;
-	u32	_pad_0x18_0x3f[10];
-	struct socfpga_clock_manager_main_pll main_pll;
-	struct socfpga_clock_manager_per_pll per_pll;
-	struct socfpga_clock_manager_sdr_pll sdr_pll;
-	struct socfpga_clock_manager_altera altera;
-	u32	_pad_0xe8_0x200[70];
-};
-
-#define CLKMGR_CTRL_SAFEMODE				(1 << 0)
-#define CLKMGR_CTRL_SAFEMODE_OFFSET			0
-
-#define CLKMGR_BYPASS_PERPLLSRC				(1 << 4)
-#define CLKMGR_BYPASS_PERPLLSRC_OFFSET			4
-#define CLKMGR_BYPASS_PERPLL				(1 << 3)
-#define CLKMGR_BYPASS_PERPLL_OFFSET			3
-#define CLKMGR_BYPASS_SDRPLLSRC				(1 << 2)
-#define CLKMGR_BYPASS_SDRPLLSRC_OFFSET			2
-#define CLKMGR_BYPASS_SDRPLL				(1 << 1)
-#define CLKMGR_BYPASS_SDRPLL_OFFSET			1
-#define CLKMGR_BYPASS_MAINPLL				(1 << 0)
-#define CLKMGR_BYPASS_MAINPLL_OFFSET			0
-
-#define CLKMGR_INTER_SDRPLLLOCKED_MASK			0x00000100
-#define CLKMGR_INTER_PERPLLLOCKED_MASK			0x00000080
-#define CLKMGR_INTER_MAINPLLLOCKED_MASK			0x00000040
-#define CLKMGR_INTER_PERPLLLOST_MASK			0x00000010
-#define CLKMGR_INTER_SDRPLLLOST_MASK			0x00000020
-#define CLKMGR_INTER_MAINPLLLOST_MASK			0x00000008
-
-#define CLKMGR_STAT_BUSY				(1 << 0)
-
-/* Main PLL */
-#define CLKMGR_MAINPLLGRP_VCO_BGPWRDN			(1 << 0)
-#define CLKMGR_MAINPLLGRP_VCO_BGPWRDN_OFFSET		0
-#define CLKMGR_MAINPLLGRP_VCO_DENOM_OFFSET		16
-#define CLKMGR_MAINPLLGRP_VCO_DENOM_MASK		0x003f0000
-#define CLKMGR_MAINPLLGRP_VCO_EN			(1 << 1)
-#define CLKMGR_MAINPLLGRP_VCO_EN_OFFSET			1
-#define CLKMGR_MAINPLLGRP_VCO_NUMER_OFFSET		3
-#define CLKMGR_MAINPLLGRP_VCO_NUMER_MASK		0x0000fff8
-#define CLKMGR_MAINPLLGRP_VCO_OUTRESETALL_MASK		0x01000000
-#define CLKMGR_MAINPLLGRP_VCO_PWRDN			(1 << 2)
-#define CLKMGR_MAINPLLGRP_VCO_PWRDN_OFFSET		2
-#define CLKMGR_MAINPLLGRP_VCO_REGEXTSEL_MASK		0x80000000
-#define CLKMGR_MAINPLLGRP_VCO_RESET_VALUE		0x8001000d
-
-#define CLKMGR_MAINPLLGRP_MPUCLK_CNT_OFFSET		0
-#define CLKMGR_MAINPLLGRP_MPUCLK_CNT_MASK		0x000001ff
-
-#define CLKMGR_MAINPLLGRP_MAINCLK_CNT_OFFSET		0
-#define CLKMGR_MAINPLLGRP_MAINCLK_CNT_MASK		0x000001ff
-
-#define CLKMGR_MAINPLLGRP_DBGATCLK_CNT_OFFSET		0
-#define CLKMGR_MAINPLLGRP_DBGATCLK_CNT_MASK		0x000001ff
-
-#define CLKMGR_MAINPLLGRP_MAINQSPICLK_CNT_OFFSET	0
-#define CLKMGR_MAINPLLGRP_MAINQSPICLK_CNT_MASK		0x000001ff
-
-#define CLKMGR_MAINPLLGRP_MAINNANDSDMMCCLK_CNT_OFFSET	0
-#define CLKMGR_MAINPLLGRP_MAINNANDSDMMCCLK_CNT_MASK	0x000001ff
-
-#define CLKMGR_MAINPLLGRP_CFGS2FUSER0CLK_CNT_OFFSET	0
-#define CLKMGR_MAINPLLGRP_CFGS2FUSER0CLK_CNT_MASK	0x000001ff
-
-#define CLKMGR_MAINPLLGRP_EN_DBGATCLK_MASK		0x00000010
-#define CLKMGR_MAINPLLGRP_EN_DBGCLK_MASK		0x00000020
-#define CLKMGR_MAINPLLGRP_EN_DBGTIMERCLK_MASK		0x00000080
-#define CLKMGR_MAINPLLGRP_EN_DBGTRACECLK_MASK		0x00000040
-#define CLKMGR_MAINPLLGRP_EN_L4MPCLK_MASK		0x00000004
-#define CLKMGR_MAINPLLGRP_EN_S2FUSER0CLK_MASK		0x00000200
-
-#define CLKMGR_MAINPLLGRP_MAINDIV_L3MPCLK_OFFSET	0
-#define CLKMGR_MAINPLLGRP_MAINDIV_L3MPCLK_MASK		0x00000003
-#define CLKMGR_MAINPLLGRP_MAINDIV_L3SPCLK_OFFSET	2
-#define CLKMGR_MAINPLLGRP_MAINDIV_L3SPCLK_MASK		0x0000000c
-#define CLKMGR_MAINPLLGRP_MAINDIV_L4MPCLK_OFFSET	4
-#define CLKMGR_MAINPLLGRP_MAINDIV_L4MPCLK_MASK		0x00000070
-#define CLKMGR_MAINPLLGRP_MAINDIV_L4SPCLK_OFFSET	7
-#define CLKMGR_MAINPLLGRP_MAINDIV_L4SPCLK_MASK		0x00000380
-
-#define CLKMGR_MAINPLLGRP_DBGDIV_DBGATCLK_OFFSET	0
-#define CLKMGR_MAINPLLGRP_DBGDIV_DBGATCLK_MASK		0x00000003
-#define CLKMGR_MAINPLLGRP_DBGDIV_DBGCLK_OFFSET		2
-#define CLKMGR_MAINPLLGRP_DBGDIV_DBGCLK_MASK		0x0000000c
-
-#define CLKMGR_MAINPLLGRP_TRACEDIV_TRACECLK_OFFSET	0
-#define CLKMGR_MAINPLLGRP_TRACEDIV_TRACECLK_MASK	0x00000007
-
-#define CLKMGR_MAINPLLGRP_L4SRC_L4MP			(1 << 0)
-#define CLKMGR_MAINPLLGRP_L4SRC_L4MP_OFFSET		0
-#define CLKMGR_MAINPLLGRP_L4SRC_L4SP			(1 << 1)
-#define CLKMGR_MAINPLLGRP_L4SRC_L4SP_OFFSET		1
-#define CLKMGR_MAINPLLGRP_L4SRC_RESET_VALUE		0x00000000
-#define CLKMGR_L4_SP_CLK_SRC_MAINPLL			0x0
-#define CLKMGR_L4_SP_CLK_SRC_PERPLL			0x1
-
-/* Per PLL */
-#define CLKMGR_PERPLLGRP_VCO_DENOM_OFFSET		16
-#define CLKMGR_PERPLLGRP_VCO_DENOM_MASK			0x003f0000
-#define CLKMGR_PERPLLGRP_VCO_NUMER_OFFSET		3
-#define CLKMGR_PERPLLGRP_VCO_NUMER_MASK			0x0000fff8
-#define CLKMGR_PERPLLGRP_VCO_OUTRESETALL_MASK		0x01000000
-#define CLKMGR_PERPLLGRP_VCO_PSRC_OFFSET		22
-#define CLKMGR_PERPLLGRP_VCO_PSRC_MASK			0x00c00000
-#define CLKMGR_PERPLLGRP_VCO_REGEXTSEL_MASK		0x80000000
-#define CLKMGR_PERPLLGRP_VCO_RESET_VALUE		0x8001000d
-#define CLKMGR_PERPLLGRP_VCO_SSRC_OFFSET		22
-#define CLKMGR_PERPLLGRP_VCO_SSRC_MASK			0x00c00000
-
-#define CLKMGR_VCO_SSRC_EOSC1				0x0
-#define CLKMGR_VCO_SSRC_EOSC2				0x1
-#define CLKMGR_VCO_SSRC_F2S				0x2
-
-#define CLKMGR_PERPLLGRP_EMAC0CLK_CNT_OFFSET		0
-#define CLKMGR_PERPLLGRP_EMAC0CLK_CNT_MASK		0x000001ff
-
-#define CLKMGR_PERPLLGRP_EMAC1CLK_CNT_OFFSET		0
-#define CLKMGR_PERPLLGRP_EMAC1CLK_CNT_MASK		0x000001ff
-
-#define CLKMGR_PERPLLGRP_PERQSPICLK_CNT_OFFSET		0
-#define CLKMGR_PERPLLGRP_PERQSPICLK_CNT_MASK		0x000001ff
-
-#define CLKMGR_PERPLLGRP_PERNANDSDMMCCLK_CNT_OFFSET	0
-#define CLKMGR_PERPLLGRP_PERNANDSDMMCCLK_CNT_MASK	0x000001ff
-
-#define CLKMGR_PERPLLGRP_PERBASECLK_CNT_OFFSET		0
-#define CLKMGR_PERPLLGRP_PERBASECLK_CNT_MASK		0x000001ff
-
-#define CLKMGR_PERPLLGRP_S2FUSER1CLK_CNT_OFFSET		0
-#define CLKMGR_PERPLLGRP_S2FUSER1CLK_CNT_MASK		0x000001ff
-
-#define CLKMGR_PERPLLGRP_EN_NANDCLK_MASK		0x00000400
-#define CLKMGR_PERPLLGRP_EN_SDMMCCLK_MASK		0x00000100
-
-#define CLKMGR_PERPLLGRP_DIV_CAN0CLK_OFFSET		6
-#define CLKMGR_PERPLLGRP_DIV_CAN0CLK_MASK		0x000001c0
-#define CLKMGR_PERPLLGRP_DIV_CAN1CLK_OFFSET		9
-#define CLKMGR_PERPLLGRP_DIV_CAN1CLK_MASK		0x00000e00
-#define CLKMGR_PERPLLGRP_DIV_SPIMCLK_OFFSET		3
-#define CLKMGR_PERPLLGRP_DIV_SPIMCLK_OFFSET		3
-#define CLKMGR_PERPLLGRP_DIV_USBCLK_OFFSET		0
-#define CLKMGR_PERPLLGRP_DIV_USBCLK_MASK		0x00000007
-
-#define CLKMGR_PERPLLGRP_GPIODIV_GPIODBCLK_OFFSET	0
-#define CLKMGR_PERPLLGRP_GPIODIV_GPIODBCLK_MASK		0x00ffffff
-
-#define CLKMGR_PERPLLGRP_SRC_NAND_OFFSET		2
-#define CLKMGR_PERPLLGRP_SRC_NAND_MASK			0x0000000c
-#define CLKMGR_PERPLLGRP_SRC_QSPI_OFFSET		4
-#define CLKMGR_PERPLLGRP_SRC_QSPI_MASK			0x00000030
-#define CLKMGR_PERPLLGRP_SRC_RESET_VALUE		0x00000015
-#define CLKMGR_PERPLLGRP_SRC_SDMMC_OFFSET		0
-#define CLKMGR_PERPLLGRP_SRC_SDMMC_MASK			0x00000003
-#define CLKMGR_SDMMC_CLK_SRC_F2S			0x0
-#define CLKMGR_SDMMC_CLK_SRC_MAIN			0x1
-#define CLKMGR_SDMMC_CLK_SRC_PER			0x2
-#define CLKMGR_QSPI_CLK_SRC_F2S				0x0
-#define CLKMGR_QSPI_CLK_SRC_MAIN			0x1
-#define CLKMGR_QSPI_CLK_SRC_PER				0x2
-
-/* SDR PLL */
-#define CLKMGR_SDRPLLGRP_VCO_DENOM_OFFSET		16
-#define CLKMGR_SDRPLLGRP_VCO_DENOM_MASK			0x003f0000
-#define CLKMGR_SDRPLLGRP_VCO_NUMER_OFFSET		3
-#define CLKMGR_SDRPLLGRP_VCO_NUMER_MASK			0x0000fff8
-#define CLKMGR_SDRPLLGRP_VCO_OUTRESETALL		(1 << 24)
-#define CLKMGR_SDRPLLGRP_VCO_OUTRESETALL_OFFSET		24
-#define CLKMGR_SDRPLLGRP_VCO_OUTRESET_OFFSET		25
-#define CLKMGR_SDRPLLGRP_VCO_OUTRESET_MASK		0x7e000000
-#define CLKMGR_SDRPLLGRP_VCO_REGEXTSEL_MASK		0x80000000
-#define CLKMGR_SDRPLLGRP_VCO_RESET_VALUE		0x8001000d
-#define CLKMGR_SDRPLLGRP_VCO_SSRC_OFFSET		22
-#define CLKMGR_SDRPLLGRP_VCO_SSRC_MASK			0x00c00000
-
-#define CLKMGR_SDRPLLGRP_DDRDQSCLK_CNT_OFFSET		0
-#define CLKMGR_SDRPLLGRP_DDRDQSCLK_CNT_MASK		0x000001ff
-#define CLKMGR_SDRPLLGRP_DDRDQSCLK_PHASE_OFFSET		9
-#define CLKMGR_SDRPLLGRP_DDRDQSCLK_PHASE_MASK		0x00000e00
-
-#define CLKMGR_SDRPLLGRP_DDR2XDQSCLK_CNT_OFFSET		0
-#define CLKMGR_SDRPLLGRP_DDR2XDQSCLK_CNT_MASK		0x000001ff
-#define CLKMGR_SDRPLLGRP_DDR2XDQSCLK_PHASE_OFFSET	9
-#define CLKMGR_SDRPLLGRP_DDR2XDQSCLK_PHASE_MASK		0x00000e00
-
-#define CLKMGR_SDRPLLGRP_DDRDQCLK_CNT_OFFSET		0
-#define CLKMGR_SDRPLLGRP_DDRDQCLK_CNT_MASK		0x000001ff
-#define CLKMGR_SDRPLLGRP_DDRDQCLK_PHASE_OFFSET		9
-#define CLKMGR_SDRPLLGRP_DDRDQCLK_PHASE_MASK		0x00000e00
-
-#define CLKMGR_SDRPLLGRP_S2FUSER2CLK_CNT_OFFSET		0
-#define CLKMGR_SDRPLLGRP_S2FUSER2CLK_CNT_MASK		0x000001ff
-#define CLKMGR_SDRPLLGRP_S2FUSER2CLK_PHASE_OFFSET	9
-#define CLKMGR_SDRPLLGRP_S2FUSER2CLK_PHASE_MASK		0x00000e00
-
+#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
+#include <asm/arch/clock_manager_gen5.h>
+#endif
 #endif /* _CLOCK_MANAGER_H_ */
diff --git a/arch/arm/mach-socfpga/include/mach/clock_manager_gen5.h b/arch/arm/mach-socfpga/include/mach/clock_manager_gen5.h
new file mode 100644
index 0000000..8d62d8e
--- /dev/null
+++ b/arch/arm/mach-socfpga/include/mach/clock_manager_gen5.h
@@ -0,0 +1,322 @@
+/*
+ *  Copyright (C) 2013-2017 Altera Corporation <www.altera.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _CLOCK_MANAGER_GEN5_H_
+#define _CLOCK_MANAGER_GEN5_H_
+
+#ifndef __ASSEMBLER__
+
+struct cm_config {
+	/* main group */
+	u32 main_vco_base;
+	u32 mpuclk;
+	u32 mainclk;
+	u32 dbgatclk;
+	u32 mainqspiclk;
+	u32 mainnandsdmmcclk;
+	u32 cfg2fuser0clk;
+	u32 maindiv;
+	u32 dbgdiv;
+	u32 tracediv;
+	u32 l4src;
+
+	/* peripheral group */
+	u32 peri_vco_base;
+	u32 emac0clk;
+	u32 emac1clk;
+	u32 perqspiclk;
+	u32 pernandsdmmcclk;
+	u32 perbaseclk;
+	u32 s2fuser1clk;
+	u32 perdiv;
+	u32 gpiodiv;
+	u32 persrc;
+
+	/* sdram pll group */
+	u32 sdram_vco_base;
+	u32 ddrdqsclk;
+	u32 ddr2xdqsclk;
+	u32 ddrdqclk;
+	u32 s2fuser2clk;
+
+	/* altera group */
+	u32 altera_grp_mpuclk;
+};
+
+struct socfpga_clock_manager_main_pll {
+	u32	vco;
+	u32	misc;
+	u32	mpuclk;
+	u32	mainclk;
+	u32	dbgatclk;
+	u32	mainqspiclk;
+	u32	mainnandsdmmcclk;
+	u32	cfgs2fuser0clk;
+	u32	en;
+	u32	maindiv;
+	u32	dbgdiv;
+	u32	tracediv;
+	u32	l4src;
+	u32	stat;
+	u32	_pad_0x38_0x40[2];
+};
+
+struct socfpga_clock_manager_per_pll {
+	u32	vco;
+	u32	misc;
+	u32	emac0clk;
+	u32	emac1clk;
+	u32	perqspiclk;
+	u32	pernandsdmmcclk;
+	u32	perbaseclk;
+	u32	s2fuser1clk;
+	u32	en;
+	u32	div;
+	u32	gpiodiv;
+	u32	src;
+	u32	stat;
+	u32	_pad_0x34_0x40[3];
+};
+
+struct socfpga_clock_manager_sdr_pll {
+	u32	vco;
+	u32	ctrl;
+	u32	ddrdqsclk;
+	u32	ddr2xdqsclk;
+	u32	ddrdqclk;
+	u32	s2fuser2clk;
+	u32	en;
+	u32	stat;
+};
+
+struct socfpga_clock_manager_altera {
+	u32	mpuclk;
+	u32	mainclk;
+};
+
+struct socfpga_clock_manager {
+	u32	ctrl;
+	u32	bypass;
+	u32	inter;
+	u32	intren;
+	u32	dbctrl;
+	u32	stat;
+	u32	_pad_0x18_0x3f[10];
+	struct socfpga_clock_manager_main_pll main_pll;
+	struct socfpga_clock_manager_per_pll per_pll;
+	struct socfpga_clock_manager_sdr_pll sdr_pll;
+	struct socfpga_clock_manager_altera altera;
+	u32	_pad_0xe8_0x200[70];
+};
+
+/* Clock speed accessors */
+unsigned long cm_get_mpu_clk_hz(void);
+unsigned long cm_get_sdram_clk_hz(void);
+unsigned int cm_get_l4_sp_clk_hz(void);
+unsigned int cm_get_mmc_controller_clk_hz(void);
+unsigned int cm_get_qspi_controller_clk_hz(void);
+unsigned int cm_get_spi_controller_clk_hz(void);
+const unsigned int cm_get_osc_clk_hz(const int osc);
+const unsigned int cm_get_f2s_per_ref_clk_hz(void);
+const unsigned int cm_get_f2s_sdr_ref_clk_hz(void);
+
+/* Clock configuration accessors */
+void cm_basic_init(const struct cm_config * const cfg);
+const struct cm_config * const cm_get_default_config(void);
+#endif /* __ASSEMBLER__ */
+
+#define LOCKED_MASK \
+	(CLKMGR_INTER_SDRPLLLOCKED_MASK  | \
+	CLKMGR_INTER_PERPLLLOCKED_MASK  | \
+	CLKMGR_INTER_MAINPLLLOCKED_MASK)
+
+#define CLKMGR_CTRL_SAFEMODE				BIT(0)
+#define CLKMGR_CTRL_SAFEMODE_OFFSET			0
+
+#define CLKMGR_BYPASS_PERPLLSRC				BIT(4)
+#define CLKMGR_BYPASS_PERPLLSRC_OFFSET			4
+#define CLKMGR_BYPASS_PERPLL				BIT(3)
+#define CLKMGR_BYPASS_PERPLL_OFFSET			3
+#define CLKMGR_BYPASS_SDRPLLSRC				BIT(2)
+#define CLKMGR_BYPASS_SDRPLLSRC_OFFSET			2
+#define CLKMGR_BYPASS_SDRPLL				BIT(1)
+#define CLKMGR_BYPASS_SDRPLL_OFFSET			1
+#define CLKMGR_BYPASS_MAINPLL				BIT(0)
+#define CLKMGR_BYPASS_MAINPLL_OFFSET			0
+
+#define CLKMGR_INTER_SDRPLLLOCKED_MASK			0x00000100
+#define CLKMGR_INTER_PERPLLLOCKED_MASK			0x00000080
+#define CLKMGR_INTER_MAINPLLLOCKED_MASK			0x00000040
+#define CLKMGR_INTER_PERPLLLOST_MASK			0x00000010
+#define CLKMGR_INTER_SDRPLLLOST_MASK			0x00000020
+#define CLKMGR_INTER_MAINPLLLOST_MASK			0x00000008
+
+#define CLKMGR_STAT_BUSY				BIT(0)
+
+/* Main PLL */
+#define CLKMGR_MAINPLLGRP_VCO_BGPWRDN			BIT(0)
+#define CLKMGR_MAINPLLGRP_VCO_BGPWRDN_OFFSET		0
+#define CLKMGR_MAINPLLGRP_VCO_DENOM_OFFSET		16
+#define CLKMGR_MAINPLLGRP_VCO_DENOM_MASK		0x003f0000
+#define CLKMGR_MAINPLLGRP_VCO_EN			BIT(1)
+#define CLKMGR_MAINPLLGRP_VCO_EN_OFFSET			1
+#define CLKMGR_MAINPLLGRP_VCO_NUMER_OFFSET		3
+#define CLKMGR_MAINPLLGRP_VCO_NUMER_MASK		0x0000fff8
+#define CLKMGR_MAINPLLGRP_VCO_OUTRESETALL_MASK		0x01000000
+#define CLKMGR_MAINPLLGRP_VCO_PWRDN			BIT(2)
+#define CLKMGR_MAINPLLGRP_VCO_PWRDN_OFFSET		2
+#define CLKMGR_MAINPLLGRP_VCO_REGEXTSEL_MASK		0x80000000
+#define CLKMGR_MAINPLLGRP_VCO_RESET_VALUE		0x8001000d
+
+#define CLKMGR_MAINPLLGRP_MPUCLK_CNT_OFFSET		0
+#define CLKMGR_MAINPLLGRP_MPUCLK_CNT_MASK		0x000001ff
+
+#define CLKMGR_MAINPLLGRP_MAINCLK_CNT_OFFSET		0
+#define CLKMGR_MAINPLLGRP_MAINCLK_CNT_MASK		0x000001ff
+
+#define CLKMGR_MAINPLLGRP_DBGATCLK_CNT_OFFSET		0
+#define CLKMGR_MAINPLLGRP_DBGATCLK_CNT_MASK		0x000001ff
+
+#define CLKMGR_MAINPLLGRP_MAINQSPICLK_CNT_OFFSET	0
+#define CLKMGR_MAINPLLGRP_MAINQSPICLK_CNT_MASK		0x000001ff
+
+#define CLKMGR_MAINPLLGRP_MAINNANDSDMMCCLK_CNT_OFFSET	0
+#define CLKMGR_MAINPLLGRP_MAINNANDSDMMCCLK_CNT_MASK	0x000001ff
+
+#define CLKMGR_MAINPLLGRP_CFGS2FUSER0CLK_CNT_OFFSET	0
+#define CLKMGR_MAINPLLGRP_CFGS2FUSER0CLK_CNT_MASK	0x000001ff
+
+#define CLKMGR_MAINPLLGRP_EN_DBGATCLK_MASK		0x00000010
+#define CLKMGR_MAINPLLGRP_EN_DBGCLK_MASK		0x00000020
+#define CLKMGR_MAINPLLGRP_EN_DBGTIMERCLK_MASK		0x00000080
+#define CLKMGR_MAINPLLGRP_EN_DBGTRACECLK_MASK		0x00000040
+#define CLKMGR_MAINPLLGRP_EN_L4MPCLK_MASK		0x00000004
+#define CLKMGR_MAINPLLGRP_EN_S2FUSER0CLK_MASK		0x00000200
+
+#define CLKMGR_MAINPLLGRP_MAINDIV_L3MPCLK_OFFSET	0
+#define CLKMGR_MAINPLLGRP_MAINDIV_L3MPCLK_MASK		0x00000003
+#define CLKMGR_MAINPLLGRP_MAINDIV_L3SPCLK_OFFSET	2
+#define CLKMGR_MAINPLLGRP_MAINDIV_L3SPCLK_MASK		0x0000000c
+#define CLKMGR_MAINPLLGRP_MAINDIV_L4MPCLK_OFFSET	4
+#define CLKMGR_MAINPLLGRP_MAINDIV_L4MPCLK_MASK		0x00000070
+#define CLKMGR_MAINPLLGRP_MAINDIV_L4SPCLK_OFFSET	7
+#define CLKMGR_MAINPLLGRP_MAINDIV_L4SPCLK_MASK		0x00000380
+
+#define CLKMGR_MAINPLLGRP_DBGDIV_DBGATCLK_OFFSET	0
+#define CLKMGR_MAINPLLGRP_DBGDIV_DBGATCLK_MASK		0x00000003
+#define CLKMGR_MAINPLLGRP_DBGDIV_DBGCLK_OFFSET		2
+#define CLKMGR_MAINPLLGRP_DBGDIV_DBGCLK_MASK		0x0000000c
+
+#define CLKMGR_MAINPLLGRP_TRACEDIV_TRACECLK_OFFSET	0
+#define CLKMGR_MAINPLLGRP_TRACEDIV_TRACECLK_MASK	0x00000007
+
+#define CLKMGR_MAINPLLGRP_L4SRC_L4MP			BIT(0)
+#define CLKMGR_MAINPLLGRP_L4SRC_L4MP_OFFSET		0
+#define CLKMGR_MAINPLLGRP_L4SRC_L4SP			BIT(1)
+#define CLKMGR_MAINPLLGRP_L4SRC_L4SP_OFFSET		1
+#define CLKMGR_MAINPLLGRP_L4SRC_RESET_VALUE		0x00000000
+#define CLKMGR_L4_SP_CLK_SRC_MAINPLL			0x0
+#define CLKMGR_L4_SP_CLK_SRC_PERPLL			0x1
+
+/* Per PLL */
+#define CLKMGR_PERPLLGRP_VCO_DENOM_OFFSET		16
+#define CLKMGR_PERPLLGRP_VCO_DENOM_MASK			0x003f0000
+#define CLKMGR_PERPLLGRP_VCO_NUMER_OFFSET		3
+#define CLKMGR_PERPLLGRP_VCO_NUMER_MASK			0x0000fff8
+#define CLKMGR_PERPLLGRP_VCO_OUTRESETALL_MASK		0x01000000
+#define CLKMGR_PERPLLGRP_VCO_PSRC_OFFSET		22
+#define CLKMGR_PERPLLGRP_VCO_PSRC_MASK			0x00c00000
+#define CLKMGR_PERPLLGRP_VCO_REGEXTSEL_MASK		0x80000000
+#define CLKMGR_PERPLLGRP_VCO_RESET_VALUE		0x8001000d
+#define CLKMGR_PERPLLGRP_VCO_SSRC_OFFSET		22
+#define CLKMGR_PERPLLGRP_VCO_SSRC_MASK			0x00c00000
+
+#define CLKMGR_VCO_SSRC_EOSC1				0x0
+#define CLKMGR_VCO_SSRC_EOSC2				0x1
+#define CLKMGR_VCO_SSRC_F2S				0x2
+
+#define CLKMGR_PERPLLGRP_EMAC0CLK_CNT_OFFSET		0
+#define CLKMGR_PERPLLGRP_EMAC0CLK_CNT_MASK		0x000001ff
+
+#define CLKMGR_PERPLLGRP_EMAC1CLK_CNT_OFFSET		0
+#define CLKMGR_PERPLLGRP_EMAC1CLK_CNT_MASK		0x000001ff
+
+#define CLKMGR_PERPLLGRP_PERQSPICLK_CNT_OFFSET		0
+#define CLKMGR_PERPLLGRP_PERQSPICLK_CNT_MASK		0x000001ff
+
+#define CLKMGR_PERPLLGRP_PERNANDSDMMCCLK_CNT_OFFSET	0
+#define CLKMGR_PERPLLGRP_PERNANDSDMMCCLK_CNT_MASK	0x000001ff
+
+#define CLKMGR_PERPLLGRP_PERBASECLK_CNT_OFFSET		0
+#define CLKMGR_PERPLLGRP_PERBASECLK_CNT_MASK		0x000001ff
+
+#define CLKMGR_PERPLLGRP_S2FUSER1CLK_CNT_OFFSET		0
+#define CLKMGR_PERPLLGRP_S2FUSER1CLK_CNT_MASK		0x000001ff
+
+#define CLKMGR_PERPLLGRP_EN_NANDCLK_MASK		0x00000400
+#define CLKMGR_PERPLLGRP_EN_SDMMCCLK_MASK		0x00000100
+
+#define CLKMGR_PERPLLGRP_DIV_CAN0CLK_OFFSET		6
+#define CLKMGR_PERPLLGRP_DIV_CAN0CLK_MASK		0x000001c0
+#define CLKMGR_PERPLLGRP_DIV_CAN1CLK_OFFSET		9
+#define CLKMGR_PERPLLGRP_DIV_CAN1CLK_MASK		0x00000e00
+#define CLKMGR_PERPLLGRP_DIV_SPIMCLK_OFFSET		3
+#define CLKMGR_PERPLLGRP_DIV_SPIMCLK_OFFSET		3
+#define CLKMGR_PERPLLGRP_DIV_USBCLK_OFFSET		0
+#define CLKMGR_PERPLLGRP_DIV_USBCLK_MASK		0x00000007
+
+#define CLKMGR_PERPLLGRP_GPIODIV_GPIODBCLK_OFFSET	0
+#define CLKMGR_PERPLLGRP_GPIODIV_GPIODBCLK_MASK		0x00ffffff
+
+#define CLKMGR_PERPLLGRP_SRC_NAND_OFFSET		2
+#define CLKMGR_PERPLLGRP_SRC_NAND_MASK			0x0000000c
+#define CLKMGR_PERPLLGRP_SRC_QSPI_OFFSET		4
+#define CLKMGR_PERPLLGRP_SRC_QSPI_MASK			0x00000030
+#define CLKMGR_PERPLLGRP_SRC_RESET_VALUE		0x00000015
+#define CLKMGR_PERPLLGRP_SRC_SDMMC_OFFSET		0
+#define CLKMGR_PERPLLGRP_SRC_SDMMC_MASK			0x00000003
+#define CLKMGR_SDMMC_CLK_SRC_F2S			0x0
+#define CLKMGR_SDMMC_CLK_SRC_MAIN			0x1
+#define CLKMGR_SDMMC_CLK_SRC_PER			0x2
+#define CLKMGR_QSPI_CLK_SRC_F2S				0x0
+#define CLKMGR_QSPI_CLK_SRC_MAIN			0x1
+#define CLKMGR_QSPI_CLK_SRC_PER				0x2
+
+/* SDR PLL */
+#define CLKMGR_SDRPLLGRP_VCO_DENOM_OFFSET		16
+#define CLKMGR_SDRPLLGRP_VCO_DENOM_MASK			0x003f0000
+#define CLKMGR_SDRPLLGRP_VCO_NUMER_OFFSET		3
+#define CLKMGR_SDRPLLGRP_VCO_NUMER_MASK			0x0000fff8
+#define CLKMGR_SDRPLLGRP_VCO_OUTRESETALL		BIT(24)
+#define CLKMGR_SDRPLLGRP_VCO_OUTRESETALL_OFFSET		24
+#define CLKMGR_SDRPLLGRP_VCO_OUTRESET_OFFSET		25
+#define CLKMGR_SDRPLLGRP_VCO_OUTRESET_MASK		0x7e000000
+#define CLKMGR_SDRPLLGRP_VCO_REGEXTSEL_MASK		0x80000000
+#define CLKMGR_SDRPLLGRP_VCO_RESET_VALUE		0x8001000d
+#define CLKMGR_SDRPLLGRP_VCO_SSRC_OFFSET		22
+#define CLKMGR_SDRPLLGRP_VCO_SSRC_MASK			0x00c00000
+
+#define CLKMGR_SDRPLLGRP_DDRDQSCLK_CNT_OFFSET		0
+#define CLKMGR_SDRPLLGRP_DDRDQSCLK_CNT_MASK		0x000001ff
+#define CLKMGR_SDRPLLGRP_DDRDQSCLK_PHASE_OFFSET		9
+#define CLKMGR_SDRPLLGRP_DDRDQSCLK_PHASE_MASK		0x00000e00
+
+#define CLKMGR_SDRPLLGRP_DDR2XDQSCLK_CNT_OFFSET		0
+#define CLKMGR_SDRPLLGRP_DDR2XDQSCLK_CNT_MASK		0x000001ff
+#define CLKMGR_SDRPLLGRP_DDR2XDQSCLK_PHASE_OFFSET	9
+#define CLKMGR_SDRPLLGRP_DDR2XDQSCLK_PHASE_MASK		0x00000e00
+
+#define CLKMGR_SDRPLLGRP_DDRDQCLK_CNT_OFFSET		0
+#define CLKMGR_SDRPLLGRP_DDRDQCLK_CNT_MASK		0x000001ff
+#define CLKMGR_SDRPLLGRP_DDRDQCLK_PHASE_OFFSET		9
+#define CLKMGR_SDRPLLGRP_DDRDQCLK_PHASE_MASK		0x00000e00
+
+#define CLKMGR_SDRPLLGRP_S2FUSER2CLK_CNT_OFFSET		0
+#define CLKMGR_SDRPLLGRP_S2FUSER2CLK_CNT_MASK		0x000001ff
+#define CLKMGR_SDRPLLGRP_S2FUSER2CLK_PHASE_OFFSET	9
+#define CLKMGR_SDRPLLGRP_S2FUSER2CLK_PHASE_MASK		0x00000e00
+
+#endif /* _CLOCK_MANAGER_GEN5_H_ */
